Problem of QoS policy

Similar Questions

• EA2700 problems installing QoS

  I have an EA2700, which has updated the firmware fo the 1.0.14 (not Cisco Cloud Connect), and the window of QoS parameters on the installation of Web does not seem to work. All fields are gray'ed out, and the installation link does not work.  The original on the configuration firmware 1.0.12 box seemed to work.  I tried to revert to the previous firmware without success.  I would take some uplink of my VOIP (VONAGE) interface priority but had no chance. Is there a problem with the new firmware?

  davidmeyer wrote:

  I have an EA2700, which has updated the firmware fo the 1.0.14 (not Cisco Cloud Connect), and the window of QoS parameters on the installation of Web does not seem to work. All fields are gray'ed out, and the installation link does not work.  The original on the configuration firmware 1.0.12 box seemed to work.  I tried to revert to the previous firmware without success.  I would take some uplink of my VOIP (VONAGE) interface priority but had no chance. Is there a problem with the new firmware?

  Why not upgrade to Cisco Connect cloud, it is easy for you to give priority to the VOIP interface since it just drag and drop! But if you're not really comfortable with it. You can powercycle the router for 10-30 seconds if not work still then reset and reconfigure the router

• QoS policy & policy-card entry on marking interface

  Dear experts from Cisco,

  I am deploying QoS on a WAN. On the LAN to the interface of a 3845 router, I need police and mark traffic between the local network. I tried to add two separate policies of the interface, but this was rejected.

  So my questions are;

  1. is it possible to have two incoming policies on an interface? If so, how?

  2. If the above is not possible how the above is possible using nested policies?

  Here's my policy:

  Policy-map MARKING
  class VOICE
  set ip dscp ef
  class in time REAL-INTERACTIVE
  set ip dscp af41
  class CRITICISM-DATA-AF31
  set ip dscp af31
  class CRITICISM-DATA-AF21
  set ip dscp af21
  SIGNALLING of class
  set ip dscp cs3
  the class of DATA MASS
  set ip dscp af13
  class SCAVENGER
  set ip dscp cs1
  NETWORK-CONTROL class
  set ip dscp cs6
  class class by default

  !

  POLICE policy-map
  class VOICE
  Police cir 5000000
  EF game-dscp-transmit action in line
  EF exceed the action set-dscp-transmit
  failure to send set-dscp action violate

  This is the error I get when you try to add the second sheet of policy to the interface:

  Router (config) #int IM 0/0/0
  Router(Config-if) #service - political POLICING entry
  Political map of MARKING is already attached

  Thanking you in advance for your help and your time.

  Kind regards

  Paul

  Disclaimer

  The author of this announcement offers the information in this publication without compensation and with the understanding of the reader that there is no implicit or explicit adequacy or adaptation to any purpose. Information provided is for information purposes only and should not be interpreted as making the professional advice of any kind. Use information from this announcement is only at risk of the reader.

  RESPONSIBILITY

  Any author will be responsible for any wha2tsoever of damage and interest (including, without limitation, damages for loss of use, data or profits) arising out of the use or inability to use the information in the view even if author has been advised of the possibility of such damages.

  Poster

  Only one service entry and/or authorized release policy.

  You don't need a strategy nested.  Change class of your MARKING policy VOICE to be what you have for your POLICE policy VOICE class.

  i.e.

  Policy-map MARKING
  class VOICE
  set ip dscp ef

  Police cir 5000000
  EF game-dscp-transmit action in line
  EF exceed the action set-dscp-transmit
  failure to send set-dscp action violate
  class in time REAL-INTERACTIVE
  set ip dscp af41
  class CRITICISM-DATA-AF31
  set ip dscp af31
  class CRITICISM-DATA-AF21
  set ip dscp af21
  SIGNALLING of class
  set ip dscp cs3
  the class of DATA MASS
  set ip dscp af13
  class SCAVENGER
  set ip dscp cs1
  NETWORK-CONTROL class
  set ip dscp cs6
  class class by default

  ! You can also set a default class marking

  ! MAYBE

• How to limit a vNic to use 5 GB/s. I can't find the good QOS policy to assign to a vNic

  Should a vNic to use the maximum of 5 GB/s...

  You don't really specify the line rate. Rate is the speed that would result in the available BW entry to be used.

  To answer the underlying question when you lower the rate, you specify burst and the value formatting.

  Formatting is discussed for example here:

  http://www.Cisco.com/en/us/Tech/tk543/tk545/technologies_q_and_a_item09186a00800cdfab.shtml#policing

  Example of

  bdsol-6248-06-A(nxos)# show run | section Gold
  policy-map type queuing org-root/ep-qos-Gold_QoS
  class type queuing class-default
  bandwidth percent 100
  shape 5000000 kbps 65000
  

  and when the use of line.

  bdsol-6248-06-A(nxos)# show run | section Platinium
  policy-map type queuing org-root/ep-qos-Platinium_5124
  class type queuing class-default
  bandwidth percent 100
  shape 10000000 kbps 5124
  

  Production of my USC in the laboratory.

  

  

• Problem definition fault policy at the level of the BPEL components

  Hello
  
  I have a composite with 2 BPELs. (BPEL1 and BPEL2). In my composite BPEL1 called BPEL2.
  My requirement is that when an error occurs in BPEL2, I want to throw 1 BPEL and BPEL1, I want to handle using fault strategies defined on MDS.
  
  < name = "oracle.composite.faultPolicyFile property" > oramds:/apps/faultpolicy/fault-policies.xml < / property >
  < name = "oracle.composite.faultBindingFile property" > oramds:/apps/faultpolicy/fault-bindings.xml < / property >
  
  The problem here is that when I use the lines above at the composite level, BPEL2 is contagious the fault using the policy of the fault. (I am pasting the above two properties just after the service tag).
  But if I want to use this manipulation in BPEL 1, I'm pastin lines above within the tag < element > 1 BPEL. In this case, BPEL2 is to launch the flaw, but BPEL1 is not able to do as the policy of the fault is not entered into force.
  
  Can someone paste a contents of composite.xml example to set the faultpolicy specific to a BPEL component, rather than the whole composite.xml?
  
  Any help on this is much appreciated.
  
  Thank you
  Prates T.

  Error binding allows to set policy for the required component fault.
  for example: -.

  
  
  xmlns = "http://schemas.oracle.com/bpel/faultpolicy."
  xmlns: xsi = "http://www.w3.org/2001/XMLSchema-instance" >

  
  BPEL1
  Medias2
  
  
  
  HelloWorld
  ShippingComponent
  AnotherComponent ".
  

  See section links fault in http://docs.oracle.com/cd/E12839_01/integration.1111/e10224/bp_faults.htm

• Better QoS policy for office video

  Hi all

  If this question is referring to the Movi time (I'll use this name for differentiation) and Jabber for Windows/Mac/iPad etc.

  Assuming NBAR is out of the question, so what means are at our disposal to ensure that the media in real time of these soft clients is found in a priority queue?

  I am aware that the VCS can apply DSCP Movi traffic tags when the media is routed through VCS, but what when the media takes the shortest path directly between customer Movi and the remote endpoint?  It is still referenced?

  What is Jabber?  These are configurable in CUCM?

  Best regards, Glen

  VCS does not mark traffic as the media does not pass through the VCS. All traces of Movi I took to direct call view all unmarked traffic DSCP 0 by default. The application is not marking traffic

• Subnet VPN IPSec problem

  Hello

  I am configuring site to site connection using the pre-shared key VPN. The VPN connection is getting up and running, but I'm having problems on information routing between subnets.

  Our subnet is 192.168.1.0 and we cannot use that subnet for VPN. Because of this, we use 10.240.86.33 for are created the IPSec traffic and destination network (PC) is on 164.2.107.56.

  We cannot connect to the 164.2.107.56 computer network, can someone help us acomplishing this \windows\system32\conifg\system?

  Our configuration is below:

  interface FastEthernet0/0
  Description $FW_OUTSIDE$
  IP 200.111.XXX.XXX 255.255.255.248
  no ip redirection
  no ip unreachable
  no ip proxy-arp
  NBAR IP protocol discovery
  NAT outside IP
  IP virtual-reassembly
  route IP cache flow
  automatic duplex
  automatic speed
  No mop enabled
  map SDM_CMAP_1 crypto
  service-policy output SDM-QoS-policy-1
  !
  interface FastEthernet0/1
  Description $ES_LAN$ $FW_INSIDE$
  IP 192.168.1.1 255.255.255.0
  no ip redirection
  no ip unreachable
  no ip proxy-arp
  IP nat inside
  IP virtual-reassembly
  route IP cache flow
  automatic duplex
  automatic speed
  No mop enabled
  !
  Router eigrp 1
  10.0.0.0 network
  network 192.168.1.0
  No Auto-resume
  !
  IP forward-Protocol ND
  IP route 0.0.0.0 0.0.0.0 200.111.XXX.XXX 2
  !
  !
  IP http server
  no ip http secure server
  IP nat pool INTERNET 200.111.XXX.XXX 200.111.XXX.XXX netmask 255.255.255.248
  overload INTERNET IP nat inside source map route SHEEP pool
  IP nat inside source static 192.168.1.0 network 164.2.107.0/24
  IP nat inside source 192.168.1.104 static 200.111.XXX.XXX
  IP NAT outside source static network 10.240.86.0 192.168.1.0/24
  !
  recording of debug trap
  access-list 10 permit 192.168.1.0 0.0.0.255
  access-list 15 allow 200.6.103.241
  access-list 15 permit 192.168.1.0 0.0.0.255
  Access-list 100 = 4 SDM_ACL category note
  Note access-list 100 IPSec rule
  access-list 100 permit ip 10.240.86.0 0.0.0.255 164.2.107.56 0.0.0.1
  not run cdp
  !
  !
  SHEEP allowed 10 route map
  corresponds to the IP 10
  !
  allowed SDM_RMAP_1 1 route map
  corresponds to the IP 150
  !
  !
  !

  Hello

  It is the router that ends the VPN tunnel? (I don't see the VPN configuration).

  Since you can't use your real address LAN, you need to NAT before you send the traffic through the tunnel.

  First, you apply the NAT rule to translate 192.168.1.0/24 to 10.240.86.33 when you go to 164.2.107.56

  NAT 192.168.1.0 ip access list allow 0.0.0.255 host 164.2.107.56

  NAT route map

  corresponds to the IP NAT

  IP pool local VPNPool 10.240.86.33 10.240.86.33

  IP nat inside source overload map route NAT pool VPNPool

  Next, you create the ACL list for interesting traffic to address coordinated at the address of the site to another

  VPN ip host 10.240.86.33 access list permit 164.2.107.56

  We will see the results.

  Federico.

• What is client group policy?

  It doesn't let me access my account.  I share the pc with my partner.

  Hi Calvin,

  Welcome to the Microsoft community.

  According to the description, you cannot share the computer with your partner that you are facing problems with Group Policy client. Am I wrong?

  1 did you changes to the computer before the show?

  2. do you get an error message/code?

  Group Policy in part controls what users can or not do on a computer system, for example: a policy of complexity of password which prevents users to choose a password that is too simple, to allow or prevent users not identified from remote computers to connect to a network share, to block access to the Windows Task Manager or to restrict access to certain folders.

  Please refer to the article for the Group Policy settings:

  http://windows.microsoft.com/en-US/windows7/Group-Policy-management-for-IT-pros.

  http://Windows.Microsoft.com/en-us/Windows7/what-Group-Policy-settings-are-used-with-BitLocker

  Note: sections apply to Vista

  Let us know if you have other questions about Windows in the future. We will be happy to help you. We at Microsoft, strive for excellence and provide our customers with the best support.

• Remove group policy that blocks USB

  I have a group policy that is configured to block access to removable devices for all users. There is a group in Active Directory (2008 R2) that users can be put to block access to the policy and a policy that allows the removable devices. When users are in the group, the registry is changed so that they should have access, but when they try to access a CD or USB drive, they get "access denied".

  The policy to block (and allow) access is by using Configuration of user - political - administrative templates - system - removable storage access. I "CD and DVD: deny read access", "CD and DVD: deny write access", "floppy drives: deny read access", "Floppy Drives: deny write access", "removable disks: deny read access ', ' removable disks: deny write access", "all removable storage classes: refuse access to all the", "Ribbon devices: deny Read access", "Ribbon devices: deny Write access", "WPD devices." ": deny Read access ' and ' WPD Devices: deny Write access.

  On the strategy of blocking, all who are set to enabled and the policy to allow it, all are set to disabled. If the user is allowed access after that be denied that they are always refused on their main computer. If they log on another computer, it works.

  Why the police work as it should?

  Hello Kevin,

  Thank you for visiting Microsoft Community and we provide a detailed description of the issue.

  According to the description, I understand that the problem with Group Policy delete that blocks USB into the computer.

  Certainly, I understand your concern and will try my best to help you.

  To get more information about it, we have a dedicated forum where these issues are dealt with and would be better suited to the TechNet community.

  Please visit the link below to find a community that will provide the best support.

  https://social.technet.Microsoft.com/forums/WindowsServer/en-us/home?category=WindowsServer

  I hope this information is useful.

  Please let us know if you need more help, we will be happy to help you.

  Thank you.

• Implementation of QoS on the border routers

  Hi all

  I have a question about the implementation of QoS in the local network. There are a bunch of L3 - L2 switches with the support of 802.1 p. 2921 SRI is on the edge of the network. I need to ensure service to certain types of traffic in the event of congestion of the uplink to the internet (attached).

  I could somehow score interesting traffic on RSR on the side LAN and apply a QoS policy? What criteria should I use? Thanks in advance.

  Hello

  Yes it is possible. You can try using the model from the following link:

  http://www.Cisco.com/c/en/us/TD/docs/solutions/Enterprise/WAN_and_MAN/QO...

  There are also other scenarios of QoS in the the reference Network Solution of QoS above Enterprise Design Guide.

  HTH,

  Alex

  * Please note the useful messages

• Issue of QoS Catalyst 3750

  Hello

  I have a scan server (IP = 1.2.3.4 for this example) who wreaks havoc when it works, which is evident in the number of drops of output I see.  I thought the police thing, but it is a production environment and 3750-G switch does not support Netflow or any other tool that would provide accurate estimates of flow to work from.

  So, my thoughts are rather to implement queuing for the scan server and limit his access to common buffers, etc..  I would like to have some feedback on the config.  (I've included notes in an attempt to illustrate my thought.)

  !**| Catalyst 3750-G | **
  !
  ! * Activate QoS
  !
  MLS qos
  !
  ! * Create custom queue-set
  ! * increase buffer 1 and disable the stamp 4
  !
  MLS qos all the output queue 2 buffers 50 25 25 0
  !
  ! * To queue 1, make available to the threshold of 1 full buffer,
  ! * reserve full buffer for the local queue only, enable
  ! * queue to borrow 3 x more common pool pads.
  !
  MLS qos all the queue of output 2 1 100 100 100 400 threshold
  !
  ! * To queue 3, make available to the threshold of 1 full buffer,
  ! * reserve 30% of buffer for the local queue only, enable
  ! * queue to borrow 4 x more common pool pads.
  !
  MLS qos all the queue of output 2 3 100 100 33 165 threshold
  !
  ! * Assign values DSCP 16, 18, 20, 22 & to queue 1;
  ! * assign values DSCP 8, 10, 12, 14 & the queue of 3
  !
  queue threshold 1 dscp-map of MLS qos srr-queue output 1 16 18 20 22
  queue threshold 3 dscp-map of MLS qos srr-queue output 1 8 10 12 14
  !
  ! * To be complete, assign COS values associated with the same queues.
  !
  queue threshold cos 1-map of MLS qos srr-queue output 1 2
  queue threshold cos 3-map of MLS qos srr-queue output 1 1
  !
  ! * Access-list 130 identifies (bidirectional) scan traffic.
  !
  IP access-list 130 allow any host 1.2.3.4
  access-list 130 allow the host ip 1.2.3.4 everything
  !
  ! * Create a class map to match previously configured access group.
  !
  class-map correspondence-any CM-SCANS
  Description * no critical analysis traffic
  game group-access 130
  output
  !
  ! * Create policy-map to assign a DSCP values to analyze default traffic.
  !
  Policy-map PM-QOS-IN
  Description * Ingress QoS strategy
  class of CM-SCANS
  set ip dscp af11
  output
  !
  class class by default
  set ip dscp af21
  output
  output
  !
  ! * Assign the queue-series 2 and/or service-policy (single entry) if required.
  !
  gix/x/x interface
  queue-series 2
  entry of service-politics-PM-QOS-IN
  output
  !

  PS - There is no voice that cross this switch, so I don't see it had to book the queue 1 for voice or turn on the priority queue, etc..

  Any help is appreciated.  Thank you in advance.

  Disclaimer

  The author of this announcement offers the information in this publication without compensation and with the understanding of the reader that there is no implicit or explicit adequacy or adaptation to any purpose. Information provided is for information purposes only and should not be interpreted as making the professional advice of any kind. Use information from this announcement is only at risk of the reader.

  RESPONSIBILITY

  Any author will be responsible for any wha2tsoever of damage and interest (including, without limitation, damages for loss of use, data or profits) arising out of the use or inability to use the information in the view even if author has been advised of the possibility of such damages.

  Poster

  Well, then you're a little stuck trying to manage the flow of this server.  Unless you want to look at the penetration of the port police server and/or to "shape" the output port.  The idea being, if you can slow down the movement of this server, you might avoid configuration QoS requirements.

  Otherwise, you're on the right track, in what you're trying to do.

  You may want to traffic of tag to this server as 'trap' (CS1).  Ideally, you may be able to distinguish the traffic 'scan' of other traffic to and from this server.

  On treatment of output of your QoS policy, rather than create a 'special' configuration to handle this traffic, you should consider having a policy that has a low priority class (scavenger), which is where direct you this traffic.  That is a policy of 4 class that takes in charge in time real (PQ), foreground (twice in 10 x % of the default value), by default and the background (1%), planning priorities.

  3750 of buffer management, I found the setting of thresholds all up and moving more if not all buffers to the pool, usually works quite well.

• VMFEX / ports VMK / QoS

  When you use (non-performing) vmfex how would you define the ports for vmotion vmk, nfs, etc. and are also using vmfex...? Is it just a case of creating a profile of port for vmotion etc, then creating a vmotion interface and attach it to the port with vcentre group?

  In addition, using this mode where you attached the qos policy? And finally, when you use UCS qos is policy applied to the FIs, as well as the adapter or just the adapter?

  Concerning

  Hello

  Yes, you can use VM - FEX vmkernel ports for vmotion, NFS trafffic. You can use existing port profile or create separate port profile and associate with the vmk appropriate interfaces.

  Each port-profile can have a QoS policy. CoS marking is done according to the QoS configuration and corresponding traffic is placed in queues in FI.

  http://www.Cisco.com/en/us/docs/unified_computing/UCS/SW/vm_fex/VMware/GUI/config_guide/GUI_VMware_VM-FEX_UCSM_Configuration_Guide_chapter7.html

  More info

  http://www.Cisco.com/en/us/NetSol/ns1124/index.html

  Padma

• QoS for tenant

  I rent a small apartment next to my house.  The tenant use the internet a lot and when I try to use it, it becomes very slow. I don't want to limit bandwidth, when I'm not home that he can use all he wants, but I want a way to give priority to my use of the internet.  My main router is a 1841 and I have already setup QoS for voice.  I just want to apply the QoS policy on his particular IP.  I give him a public IP address and it connects his router.

  So, basically, I want to have him use internet at full speed, until I decide to use it, at that time my stuff will prevail on his stuff.  It will always be unless it is VoIP, then VoIP stuff will always take precedence over everything.

  The 1841 has two interfaces Fa0/0 is my WAN and fa/0/1 my LAN.

  How can I do this?

  Bandwidth control is what is used to establish the value of percentage Yes.

  Queues of traffic is only really makes sense when you let the router not load Rx is already received over your WAN interface.i.e. entry.

  Then apply the policy to output interfaces (output) and that should do the job.

• Implementation of QOS for on multiple switches for two VLAN

  afternoon all that I was looking for a little help in configuring QOS for two local area networks VIRTUAL, I created. These will be for voice traffic vlan 22 and traffic video vlan23. I also have three other VLAN for pc, wireless devices and our cnc machines. We have 5 switches which are all SG30028P with a single switch making the intervlan routing (Layer 3-powered). all switches are resources shared by the main switch and ive been through the guide written on how to do it on a single switch, which I think is layer 3.

  could someone help me with what I want the video and voice to take precedence over the rest of the traffic

  best regards Patrick

  Right, this way, you can give priority to IP or MAC address.

  No, there is nothing different, only one review of the routing. As the L3 switch can make local routing decisions, the placement of the ACL can vary. In an L2 environment, all packages are transferred to the router, then back down the network to the local destination, so you can clear an ACL on the uplink.

  Since you have a L3 switch, you can practice the same, empty an ACL on the link downstream for L2 switches for all traffic subject to the ACL. Any connection to the L3 switch, you can of course apply an ACL to the uplink router to get all notice of incoming traffic correctly. You can also apply a policy on port source interface to get the note as soon as traffic hits the switch.

  QoS policy is the concept of an ACL, you want it is the closest to the resource. If you apply a QoS policy an uplink upward, QoS will be marked up when it hits this port. Not before. So it should be applied closest to the device as possible. Many times, local QoS is not as important, until it starts to get to the router. As most Cat 6 environments can generally manage all local traffic. So, depending on the number of devices and the amount of traffic, a decently robust network can handle all traffic local then you just give priority to the uplink remarks to ensure that what is important is first.

• Group Policy client could not start

  Hello

  I have a problem of Group Policy Client on a stand-alone computer with Windows 7 SP1. When the computer starts, the main account can be accessed as usual, but once the office is reached, a notification bubble appears indicating that Group Policy Client didn't start and that standard user accounts cannot be loaded. Administrator accounts have worked normally until recently, where administrator privileges have begun to not be available in Mozilla Firefox.

  Do you know how to fix this?

  Hi Kiran,

  Thanks for the reply.

  Make sure that the Group Policy client service is running.

  See the following steps:

  a. click Start, type runand press enter

  b. type services.msc , and then click OK.

  c. search customer service strategie strategy group, right-click on it and click Properties.

  d. Make sure that Service status is started and the startup type is automatic

  e. click on apply and OK.

  Thank you.