Problem of satellite L850 - warning system - one with the cooling system

Similar Questions

• Satellite A660 - message: WARNING: a problem with the cooling system

  My laptop recenly started giving the error "Warning: a problem with the cooling system has been detected." Please turn off computer immediately and return it for service"- Yes the fan had stopped working and touchpad area was hot.

  So I take it on the type of service (toshiba) and must answer for fan, Mo, HARD drive, he said. Is this possible? -J' I have extended warranty, but is ' t it much? not to mention that it takes a month to get things down.

  He also mentioned that I could use the machine with a cooling pad until then if I wish.

  Any feed back?

  > Yes the fan had stopped working and touchpad area was hot.

  In this case, there is really a hardware problem.
  But I m wondering why he should replace the HARD drive and the motherboard
  Perhaps only the cooling module began at malfunction of course this is just a speculation
  If the technician has checked the material, then they need to know what parts are not OK.
  So don t think you have no choice.

  But the guarantee is valid for all is free

• Satellite P500-12D - a problem with the cooling system has been detected.

  Hi there everyone,

  I bought a Satellite P500-12D, which was a return of retail. When I start it up it runs a few minutes and then it appears on the screen:
  WARNING: A problem with the cooling system has been detected. Please, turn off computer immediately and return it for service.

  Follow the health of toshiba CPU is less than 50% temp and if it goes much higher that the cooling fan turns on and it lowers down and the fan stops again, I noticed that only the fan works r/h to cool the cpu, both should come together? What is a software problem?

  TThe unit is new without even the plastic off the surround screen or webcam. Any help or even point me in the right direction would be much appreciated, gary

  Hello

  Which program gives you this error message about the cooling system?

  Before contacting a service partner, as you can read in the error message, you must clean the cooling system using a jet of compressed air. Maybe dust blocking the fan or something else. Of more to clean up it of not necessary to disassemble.
  Here is an article on this topic: [how to clean a Toshiba laptop cooling system? | http://forums.computers.toshiba-europe.com/forums/ann.jspa?annID=40]

  If it doesn't help, contact the nearest service partner.

• Satellite C660D - a problem with the cooling system has been detected

  My laptop is a * Toshiba Satellite C660D-11th * and I have a message that keeps coming up every once in a while 'alert system' head and reads as follows: "WARNING: a problem with the cooling system has been detected." (Next line) Please, turn off computer immediately and return it for service. »

  I had this warning for the coming weeks and it tolerated, but it worsened and annoyed me for the last time. I can hear the fan and the computer is not over heating (the CPUCool freeware tool detects a 51º CPU temprature C). No further questions arise as the computer slows down, it is right in the path of what I do, like typing right now.

  I tried to solve the problem by changing the "Power Options" in the control panel of Windows 7 'High Performance', and then selected under the 'battery' both 'Sector' columns, 'Never' for the parameter "put the computer to sleep. It seems to work, and no error message has occurred since then. However, this is not a solution...

  Please help quickly, this prevents me from working and even other things now.

  Thank you

  Hello

  Usually, this message would appear if something is not wrong with the cooling system. But I read here in the forum that maybe it's a bug of software and after new system recovery this message should no longer appear.

  But if you notice some upper temperature or abnormal noises, then I recommend to check this with a service technician

• Error message "A problem with the cooling system" on Satellite A660

  Hi all

  Hope I can get help here. I got about 5 laptop computers HP after each of them had problems and errors. I got sick of them and so got a refund and bought a high spec A660-1FH.

  The A660 is a great laptop for two days until yesterday when I started having a saying of warning message "a problem with the cooling system has been detected. Please turn off the power immediately and return it for service "."

  The cpu fan works fine you can here it turns and the temperature of the processor i5 - 460 m is around 40 degrees for two hearts - that seems normal to me. I noticed that this happens only when running on battery, and if you switch from eco utility to the power saving mode. Its fine when running on the "balanced" power setting The fan is louder before when this message appears.

  Like its less than 28 days my retailer swapped it for a brand new immediately. Got a new home page, and the same message reappears. Everyone knows this. Like two laptops had this, I was wondering if it is normal that the laptop A660 series or if it was really a hardware problem?

  I tried to update the eco utility and the bios of the laptop, but the two are the latest versions. Can someone help or share if they have a similar problem with their laptop?

  Thank you

  In front of me, I have Satellite A660-13 q (PSAW3E) and I have about 6 weeks now. It works almost 10 hours a day and so far I didn't notice this message or anything that may be suspect for the operation of the equipment.

  I put really know why this happen on your laptop and don t think that there is nothing you can do about it.
  I would trade it again. What you can also try is to contact the closest service Toshiba. Make a call, explain the situation and ask if they can help you with this.

• Satellite U500 - problem with the cooling system has been detected

  I have a Toshiba Satellite U 500 series, and I just got a message saying "a problem with the cooling system has been detected. Please turn off the power immediately and return it to service.
  Before that, I would like to know if anyone has had this problem and if there is a software solution?
  HIERARCHICAL

  Check HERE to see if anyone else had this problem in the past.

• Satellite A40 - attention: problem with the cooling system has been detected.

  Hello guys,.

  From time to time, I get the following message is displayed:

  WARNING: a problem with the cooling system has been detected Toshiba
  Please turn off computer immediately and return it for service.

  I have Windows XP on it.
  I opened the cooling fan and clean it. Of course, I found it dirty rally.
  But still, I get this message!
  What should I do?
  I live in Northern Germany.

  Any advice is welcome and thanks in advance.

  Ibrahim

  Hello

  The message says it all!
  In this case you should contact the service provider authorized in your country!

  > I opened the cooling fan and clean it. Of course, I found it dirty rally.
  Eventually, the cooling modules don t like needs and that is why the message again!

  Nothing to my friend... you need help laptop technician

• Satellite C750-A103 made a lot of noise - problem with the cooling system

  My toshiba machine made a lot of noise... like a plane. And it gives me the message "a problem with your cooling system has been the detection.

  Turn off immediately and come back for the service "."
  What should I do? It has been recently formatted, also?

  + The message was edited: mode number + added

  You did not provide details on your laptop model and system that is installed on the laptop.

  Even his I don't know how old is the laptop, but according to this short message, it looks like there is a problem with the cooling system.

  Probably notebooks cooling fan doesn t work properly and the unit cannot be cooled as it should this can lead to cell damage through an internal temperature longer.

• Qosmio G20 error message: problem with the cooling system has been detected

  I'm trying to fix a Qosmio G20 (which is about 3 years old, it is no longer in warranty).

  Error message: Warning: a problem with the cooling system has been detected.

  I managed to remove the outer case and observe the operation of the machine, and basically one of the fans does not at all. The fan which is closest to the power connector seems to work very well (he seems to be turning a lot, do not know if this is normal), but the other fan who does not seem to move at all.

  When I put in place the case and on the machine, I noticed after a few minutes the vent of the fan working heat sink had warm enough, while led the non-working fan remained cool.

  I cleaned the fan from dust and have also changed the BIOS battery mode mode high performance, but the problem still exists.

  I would be grateful if someone could give advice if the problem is the fan or something else.

  If the fan is the problem, where I can buy a: i live in the United Kingdom?

  Hello

  I think there might be something wrong with the cooling module and the replacement would be necessary.
  Usually, this should be done by an authorized provider (ASP) in your country.

  Technicians could replace it with a new part and also could renew the thermal grease which is placed between the module and the CPU cooling.

  So contact the ASP in your country and ask for later handling.

  By the way; also, you can buy the cooling of the ASP module!

  Good luck

• Qosmio G10 - a problem with the cooling system

  Hello

  Put on my G10-100 this morning and got the following message:

  "A problem with the cooling system has been detected. "Please turn off immediately and the return of serve.

  My other machine running and connected on toshibas website and found the number of support.

  After which left a message there, the automaton response was "we aim to get back to you within the hour," Needless to say, it's now 6 hours later.

  I can't find whether on the web or in these forums, has anyone encountered this before?

  I'm still in my 1 year warranty, but he soon run out.

  Thank you
  James

  Hello

  This looks like a problem of overheating on your device.
  In this case, you must contact the ASP.
  I don't know if it's a phone number just to post you but please visit this m link:

  http://EU.computers.Toshiba-Europe.com/cgi-bin/ToshibaCSG/generic_content.jsp?service=EU&ID=ASP_SUPPORT

  You will find a Toshiba service partner who is responsible for your country.
  It should help you to solve this problem

  Good bye

• Hello! I use a PC and have problems loading my homepage of Muse. First of all, I made one with the address "nordensstjarnor" and updated several times without any problems. And once, I couldn't download on 'nordensstjarnor' any longer. Don't know why, s

  Hello! I use a PC and have problems loading my homepage of Muse. First of all, I made one with the address "nordensstjarnor" and updated several times without any problems. And once, I couldn't download on 'nordensstjarnor' any longer. Don't know why, when he got the address "nordensstjrnor". That me ok at first, but now I really need to give the first address once again, "nordensstjarnor". But when I try, the alternative of the site of ' publish on ' old isn't here. And if I try to create a new one, but with the old URL, the box turns red. What can I do?

  The reason why you cannot change nordensstjarnor.businesscatalyst.com is because a different Adobe ID is used for the publication of this site.

  t * [email protected] is used for the publication of nordensstjarnor.businesscatalyst.com

  t s. * [email protected] is used for the publication of nordensstjarnorindex.businesscatalyst.com

  You must make sure that Adobe ID is used in account publish, so that you can see a list of the websites published under this account. Go in Edition > Preferences > publish on Business Catalyst > publish with accounts

  You can pass the accounts for you can also make changes to the sites.

  Thank you

  Sanjit

• 23 envy d027c All In One with the card mother Lavaca3-SB IPISB - NK. How to upgrade the video card?

  I have a HP Envy 23 d027c All In One with the card mother Lavaca3-SB (pegatron) IPISB-NK.  It has a PCI slot available for upgrade of the video.  I want to do this.  I intend to use the pc for video processing and maybe a few games.

  How to pass the video?

  What cards are best for this system?

  What has changed in the BIOS or other settings I should do?  How can I get them?

  Thank you

  Art

  The PCIe MXM slot is for HP install graphics cards in some models CTO (configure-to-order). Without the card installed when you purchased the computer, there the fan and radiator bad sets. You will need to buy a graphics card and the heatsink / fan of HP to try to upgrade the GPU in your computer. There is an extensive disassembly involved in this procedure. All-in-One computers have much more in common with laptops than they do with traditional desktop computers.

  Honestly, if you want to do video processing and games... you should get a traditional desktop with enough CPU and GPU for these activities.

  Please click the White Star of KUDOS to show your appreciation

• Ran Malwarebytes & two threats were each one with the same name: PUM. Disabled.SecurityCenter. fact that associated with MSSE PUM & the boxes unchecked in MS security Center.

  Original title: PUM. Disabled.SecurityCenter

  I recently removed "patch system" of my Dell computer XP. Malwarebyte s was the only software to do. MSSE caught, but couldn't fix it. I then updated & ran MSSE on my Toshiba - no threats not found. I then ran Malwarebytes & two threats were each one with the same name: PUM. Disabled.SecurityCenter both at the Date of the registry in HKLM\SOFTE\Microsfot\SecurityCenter\AntiVirusDisableNotify & HKLM\SOFTWARE\Microsfot\securityCenterFirewallDisableNotify.  These two have been listed bad: Good (0) (1).  In the Malwarebytes wesite, I read that this has something to do with MSSE. In a commentary, he says it occurs if, in the MS Security Center, the notification "Notify me if my computer might be at risk because of my virus protection software settings" is unchecked.  I then went ahead & check all 3, firewalls, viruses & automatic updates. My computer seems to work well, except that the fan runs all the time (there are a lot of processes running & the CPU usage is very--often 100%, but the computer works fast).

  My questions are: 1) the PUM associated MSSE & the boxes unchecked in MS security Center; (2) should I click on "ignore" in the Malwarebytes scan? 3) was right to check all the boxes in the center of security - "altert me if my computer may be at rist b/c of my xxx software settings?  Thanks in advance for your help.

  PC fan2

  Hello

  (1) is associated with MSSE PUM & the boxes unchecked in MS security Center;

  The following thread might answer this question: http://forums.malwarebytes.org/index.php?showtopic=69859

  (2) should I click on "ignore" in the Malwarebytes scan?

  Yes

  3) was right to check all the boxes in the center of security - "altert me if my computer may be at rist b/c of my xxx software settings?

  Only, run antivirus software at the same time. Firewall must be performed, evil-ware bytes can be run at your pleasure.

• I'm trying to migrate data from a server to a new one with the file permissions of the files of users and records lost.

  original title: robocopy

  I'm trying to migrate data from a server to a new one with the file permissions of the files of users and records lost. So far, that's what I did, I used \\server1\share \\server2\share/sec /mir robocopy and robocopy \\server1\share \\serve2\share/e/s /copyall. It seams like they copied all files with the permissions of the user for the files, but not files. For example, if a user makes a folder with the files in the folder appear them have permissions appropriate for them but not the root folder or subfolders, they did... How can I fix this and what is the difference between / s /mir and/e/s /copyall?

  Hello

  You can find the Server forums on TechNet support, please create a new post at the following link:

  http://social.technet.Microsoft.com/forums/en/category/WindowsServer/

• Accidentally that hidden/removed the base Panel (the one with the shadows, made highlights, contrast, exposure) to develop module. I was clicking on the exposure slider when my mouse slipped and I clicked on something. How to do back panel?

  Accidentally that hidden/removed the base Panel (the one with the shadows, made highlights, contrast, exposure) to develop module. I was clicking on the exposure slider when my mouse slipped and I clicked on something. How to do back panel?

  Make a right-click on any other Panel name develop. In the menu that appears, put a check mark next to the base.