problem with size of power supply for HP6774y upgrade?

I ordered a power SUPPLY Corsair TX650M block as an upgrade. Do this in anticipation of adding a new video card. Thought I had done my homework in the choice of this power supply, but I'm a little distracted by the holidays.

I was surfing just these cards and it is clear another poster that Corsair POWER supply does not fit well it is rated for this size case.

Will want to return it without opening it if this is true. Can someone suggest a modular PSU that adapts no doubt? (I mean only to this one!)

You will enjoy really any help/suggestions.

Diablesseblu,

By returning your other post and lifting all the data, please check my comments.

(1) use have a HP with a 250W supply p6774y.

http://support.HP.com/us-en/document/c02629593

(2) you bought a DIAMOND 6570PE31G Radeon HD 6570 1 GB 128 - bit DDR3 PCI Express 2.1 x 16

This card draws only 50W. It requires that no power does the PSU.

http://www.Newegg.com/product/product.aspx?item=N82E16814103188&TPK=Radeon%20HD%206570

(3) odered the Cosair TX650M

Have you opened the file and actually measured depth of PSU exists on this matter. It should be 5.5 ". If you have another 'inch' of tolerance, I would not worry about it.

As a comment, the 650 is excessive (IMHO), unless your planning on future additions, or perhaps improve the graphics of cards to the 6950 (which only requires a min of 500W).

Your also right, I'm pretty critical of the dimensions of the Corsair. I see too many references to the OCZ and Corsair and rarely see a comment about you measure the depth of cementation, with the exception of the Big_Dave.

Tags: HP Desktops

Similar Questions

  • Problems with the DC Power supply QL 355TP: I can not set the tension level

    Hello

    I'm trying to control a power supply DC via GPIB. The power supply being used is the QL355TP of society Thurlby Thandar Instruments (TTi). There are no drivers of OR to control the instruments, then I need to download and install the driver from the website of TTi: the package I installed is as follows:

    "QL - P power supplies, (including QL Series II) series pilot National instruments (Labview and CVI)"

    and I also installed the following:

    "QL - P power supplies (including QL Series II) series, IVI driver"

    So, my problem is that when I try to use the sample application of the driver 'Volts.vi DC Ouput'; defines a specific level voltage, does not work properly. The application gives no error, but it is not set the specific level voltage. However, other functions work properly, as the measure or activate the output. I tried a lot of things, but I don't know why it does not work.

    I enclose the block diagram of the application and the front panel:

    I must say that I barely control instruments using Labview and is possible that this problem would be because I did not consider things basic and mandatory.

    Any help is appreciated.

    Thank you.

    p.s. Try to replace the decimal comma to period. It is possible that the driver does not correctly handle the comma.

  • Need the dimensions of XPS8300 power supply for the upgrade.

    So I bought a Dell XPS 8300 on sale Black Friday mainly because of the processor, RAM and HARD drive.  I need a new computer and wanted it to be fast but also wanted a desktop computer, because I intend to upgrade to a better quality of game.  I plan on upgrading the graphics card to a Geforce GTX 560 Ti FPB.  I understand that this will require a more powerful power supply and seeks to those at the moment, probably a 760W supply.  My concerns are mainly regarding the power supply box installation.

    Currently my XPS 8300 has a 7P3WV 460W power supply.  Part # H460AD-00Someone has dimensions on this so I can get a power supply that will compete?

    Or if no dimensions does anyone know of a compatible PSU?

    Finally, I intend to switch on the case and motherboard and all simply transfer on the parties but that is further down the road.

    Thanks in advance!

    nefastusaequitas

    Generic standard ATX power supply can be installed, with a power of 20 + 4 pin main motherboard, or 24 pins as the XPS 8300 has a rear panel open, with or without the on/off switch.

    You should be able to buy a compatible power supply either a local computer or online store.

    Note: A power supply with four SATA power connectors, is necessary.

    Bev.

  • HP Pavilion G4 1310AU: problem with power supply for laptop HP Pavilion G4 1310AU

    Hi This is my first thread in the toms hardware, I have problem with my laptop power supply. my laptop cannot turn on if I remove the battery and use the charger only, but if I use my cell phone battery can turn on without problem for my laptop to use the battery to turn on and after my laptop that works and I remove the battery my still laptop running with the charger plugged, and that I charge my phone when my battery<80% capacity="" e.g="" on="" 40%="" battery="" power="" my="" laptop="" underclocked="" processor="" speed="" to="" 800="" mhz="" from="" 2.5="" ghz,="" i="" have="" changed="" power="" management="" in="" windows="" setting="" and="" amd="" catalyst="" to="" running="" full="" speed="" when="" plugged="" in="" and="" charging="" but="" my="" laptop="" still="" underclocked.="" i="" have="" updated="" my="" bios="" with="" latest="" version="" but="" still="" underclocked.="" after="" 100%="" fully="" charged="" my="" laptop="" processor="" running="" in="" full="" speed="" at="" 2,5="" ghz...="" other="" that="" no="" issue="" in="" my="" laptop,="" everything="" running="">

    I'm never use my laptop for 3D games, most of use for the office, watch video, listen to music and navigation

    My computer laptop specifications
    AMD A4 3305M 1.9 Ghz Turbo up to 2.5 Ghz (TDP 35watts) (Dual Core)
    2 GB OF DDR3 RAM
    HARD DRIVE 500 GB
    DVD RW
    Bluetooth
    14 "monitor

    What is my charger underpower for power to my laptop? my charger is genuine HP with 65 Watt (18, 5V and 3, 5)
    should I buy charger 90 watt (19V and 4.74)?
    or my default charger? so, my charger not Power not in 65 Watt as a specification written in but less than 65 watts running?

    Thank you

    Sorry for my bad English

    Hi @Dana88 ,

    Please contact our technical support at 800-474-6836. If you do not live in the United States / Canada region, please click on the link below to get a number of assistance for your region.

    World wide phone holder

    I understand that if you remove your battery, you can't boot up your laptop.  This is not unusual. some laptops are set up in this way.

    I understand that when you have the phone connected and charge the batteries of your performance is lowered.  There is more than one draw powere when it loads to the battery.

    Here is a link to the laptops HP - test and calibrate the battery (Windows 7) to ensure that there is no problem with the battery.

    Could also remove the battery once you put under tension.

    You asked questions on the use of a 90-Watt adapter.  Here is a link to HP G4 Notebook PC Maintenance and Service of Guide.  Chapter 3 page 32 lists not one that is recommended.

    Good luck!

  • Upgrade power supply for dell Inspiron 530 (not slim)

    Yes, it's an old computer, but I want to upgrade the power supply for it. Watts, preferably something of 400 or more, but I can settle for 350w or 300w

    I have improved the power supply on an Inspiron 530 with an Antec 550 watt modular power supply with no problems.  Just be sure to buy a power supply of standard size, and you should have no problem.

  • Need new power supply for my HP p6210y

    Hello

    I have a HP p6210y (http://support.hp.com/us-en/document/c01859864) and I need to upgrade the power supply for the Radeon HD 4890 I have now. I am reviewing the PSU below. However, the dimensions are actually smaller than my current diet. Who's going because of my problems in terms of ride it properly in the case?

    http://www.Newegg.com/product/product.aspx?item=N82E16817338038

    If this will cause problems, can anyone suggest a power supply (it's the exact size as my current) which would be suitable for my graphics card. I need "500W with two connectors to power 75W 6-pin PCI Express.

    Thank you!

    I believe that the PSU is designed for a different style of the case. Discover the Corsair CX500, or CX600 power supplies. They are highly recommended and are favorite forum. In addition, they are only slightly larger than the stock power supply HP and are known to adapt.

    Frank

  • HP Elite 1090-T H8: seeking your suggestions for upgrading the power supply for a new video card

    I have a HP EliteH8-1090 t who is about a year, but with an AMD Radeon HD 6570 low power graphics card and a 450W power supply. I want to upgrade the 650W power to support the installation of a replacement graphics card.

    I tried to replace the HP 450W with Corsair TX650 and Corsair TX850 food. The system appears to power (DVD drawer opens and closes, the hard disks spin, fans run) with either a Corsair, he's stuck at this point. My system is unable to enter start mode when either power supply is installed - it seems stuck in a mode of seed, and the monitor still asleep.

    Can someone please advise on a compatible power supply for HP system? I'm puzzled by why a simple exchange of a power supply does not work. Just like a record, the system has a card mother Pegatron IPMTB-K (Truckee).

    Thank you!

    No problem. I wish you good luck with it. On a positive note the HX650 is a much better than the TX650 ILA unit internal quality and what I like is the best it's quite fan fan much quieter than the TX650 while helping your organization of cable being modular and help keep temperatures cooler in your computer case.

  • Qosmio X X 770-11 - new motherboard and power supply for sale

    Brand new motherboard and power supply for sale

    Posted by jtk
    Brand new motherboard and power supply for sale

    Also Intel® Core i7-2670QM CPU
    4 096 + 4 096) MB, DDR3 RAM (1 333 MHz) memory
    1 000 hard drive (Solid State hybrid 4 G Drive with 500 GB and 4 GB of memory NAND flash + 500 GB) GB
    Jim Kerr sent from my iPad

  • HP 8200 elite CMT: can I use an external power supply for AMD Radeon HD graphics card 7770?

    I have HP 8200 elite CMT CPU in which 320 watts PSU is installed. I want to use AMD Radeon HD 7770 requiring more power (minimum 400 watts power supply) for maximum performance. But the fact is, the higher Watt PSU is not available for my cpu because its cables do not match that. So I ask if I can use the external power supply to power my GPU instead of the CPU power. Will be this harm to my PC?

    Kindly help me to solve this problem.

    Thank you

    Thank you for the information, @haseebkhan7310.

    I'm not a fan of using a separate power supply to power a video card.  It can cause problems.  However, here is a video that will show you how it can be done:

  • I need power supply for HP Z220 CMT workstation up to 500 watt

    HI everyone I want to improve my diet is 400 watt, this does not work with my new graphics card, it's Asus GTX 770 Nvidia GeForce DirectCU II OC 2 GB GDDR5 he needs a minimum of 500 watts...
    Thank you very much for everything give me it please link or model power supply for hp workstation z220 up to 400 watt.

    Hello:

    Power supply in the z220 belong to someone, which means that you can not install any other food but the 400W provided by HP.

    You can also ask your question on the HP Business Support Forum - z section of jobs to see if anyone knows if one different PSU from another series of z that Workstation will work for your model.

    http://h30499.www3.HP.com/T5/workstations-z-series-XW-series/BD-p/BSC-272#.U5nJ2f1OXGg

    For example the z600 has a 650W power supply, but I have no idea if this P/S will work in the z220.

    Perhaps someone on this forum will have some alternatives for you, but don't get your hopes up.

  • Power supply for use in the UNITED Arab Emirates

    Hello

    I just bought a Time Capsule of the airport and an Apple TV (4th gen).  I'm moving to Dubai for work and I intend to take with me.  I can't find out how to replace the power supply for use in Dubai (plug type G).

    • Can I just buy a travel voltage converter?
    • What is the frequency difference (US is 60 Hz and UNITED Arab Emirates is of 50 Hz)?
    • Could I just buy a 'EnergyPal travel Charging Station ETCS04' and connect directly?

    Thanks for any help!

    The airport Time Capsule and the Apple TV work on 100-240 Volts and 50/60 Hz automatically, so they'll work pretty much anywhere in the world if you have the map of the right ankle.  A voltage converter is NOT necessary.

    You can buy the cards you need to any store from the airport, luggage, in Dubai store, etc., most of the hotels the.  If I remember correctly, Dubai uses the same type of plug that she used in the United Kingdom, as well as should work as well.

    http://www.Amazon.com/Ceptics-grounded-Universal-Plug-adapter/DP/B0080R95XI/ref= sr_1_1? ie = UTF8 & qid = 1455557366 & sr = 8-1 & key...

    I do not think that the higher 5 GHz channels are permitted in Dubai, so be sure to put the time Capsule to use a lower numbered GHz 5 channel... 36, 40, 44 or 48.

  • Power supply for Pavilion 720 a and a GeForce 6200 video card

    I bought for a GeForce 6200 card video from Amazon. Only when it happened is because he said that it takes 300 watts or more PSU. My 720 a Pavilion has a HIPRO HP-D2537F3R power supply nominal maximum of 250W.

    My questions are:

    -Does really need 300W or she would work on 250W without burning down the House!

    -If I had to put in level how do you know which suit the PSU? Can you recommend an and a provider. I saw the useful video on the replacement of the PSU. It seems simple enough.

    Thank you

    Tim

    6200 is a GPU very low power.  It will work fine with the stock power SUPPLY HP block.

  • Get a new case and power supply for my HP Pavilion a6355.uk

    1. sound of the HP Pavilion a6355.uk

    2. Windows 7 Professional 64-bit

    3. no error message

    4. it is not a problem, but its had a new graphics card, new ssd, another hard drive, removed the 500 GB hard drive, and that's all I think.

    Hi, I want to get a new case and power supply for my office

    If I want is http://www.pcworld.co.uk/gbuk/antec-one-0-761345-15970-8-atx-full-tower-pc-case-black-13374257-pdt.h...

    The power I want is http://www.pcworld.co.uk/gbuk/zs650w-uk-zs-series-ocz-zs650w-uk-atx-psu-650w-11342059-pdt.html

    Is 650 Watt most the jury can take? I read somewhere that most can take is 650 watts.

    My only concern is that, how do you take the I/O shield? I've never done before.

    Yes, it will fit your card mother Μatx.

    PS > remember to toggle the toggle SOLVED / SOLUTION to the right of MY post/reply.

  • Power supply for Pavilion a6720f?

    Hello. Is power supply for an a6720f a standard ATX, or something exclusive? I need to know.

    Thank you.

    This is a standard size ATX PSU - 5.5 "by 5.9" by 3.4 "but confirm this by opening your PC and by measuring the PSU.  Go back to the bottom of all the cables coming from the PSU for the endpoints so that you know which links are necessary.

  • The upgrade of the power supply for a HP Pavilion 500-054

    Hey people,

    I'm changing the 500-054 flag so that it can play a few games, not a hardcore gamer, just want to be able to play the occasional game. I want to get a lower end external video card, but this requires a power supply greater than 300. I am looking for a new power supply for my computer, but I couldn't find one for the 500-074. Are the ones that will work for my computer or I am a hopeless case?

    Thank you

    A standard ATX power supply will work. Please look at the Corsair CX430, CX500, CX600, or their variations of modular cables for your needs.

    If you have any other questions, feel free to ask.

    Please click the White Star of KUDOS to show your appreciation

Maybe you are looking for

  • You Tube goes all warbley after 4 minutes from Windows 8.1 installation, why?

    I bought a new Windows 8 two years ago, and then they have updated to Windows 8.1. After 4 minutes, something usually playing on You Tube, it gets static warbley & mess the rest of the time. Please fix this because he has never done that on Windows 8

  • multitrack recording with the living presonus studio

    I have a mixer 16.4.2ai people and prefer to use logic pro as my DAW.  With the presonus capture, I can automatically record/capture all channels of entry without having to assign each channel whenever I record.  Is it possible to do it with logic? C

  • Satellite Pro A120: I have a warranty available without proof of purchase?

    Hello My laptop Toshiba Satellite pro A120 computer has been giving me problems after problems; I posted my problems everywhere online on popular technical websites, but without a lot of help similarly really cleaver people; I bought this new laptop

  • FFT waveform recorded

    Hi all I am fairly new to LabView and data acquisition. Sorry to bother you. I have a question: "I recorded a waveform distorted by using digital oscilloscope. The format of the file is .bmp i.e. photo brush. I want to perform the FFT of this wavefor

  • Game WGA600N adapter used to connect to the router WRT310N but not now.

    I have a game WGA600N adapter that connected perfectly to a WRT310N router. Has worked for 2 months. Then one night while being connected via the adapter for games, connection has been lost. I was unable to reconnect since. I have reset the router an