Problems in the Service Console command esxcfg-firewall running

Similar Questions

• What is the service console command to give the IP address of the ESX host?

  What is the service console command to give the IP address of the ESX host? /

  What is the command to give the IP address of a host that has no IP?

  see this

  http://KB.VMware.com/kb/4309499

  It's good to have as well

  http://VMware-land.com/esxcfg-help.html

• Service console command

  Hello

  I'm new to this group.can give me the service console command to get the version of the firmware of the HBA in ESX 3.X.Thanks in advance

  With love... Rocky

  Using the cat/proc/scsi/YourDeviceName/1. less

  or cat/proc/scsi/YourDeviceName/1. grep driver

• Command not found in the service console ESX 4.0 u2

  Hi all

  I have a very simple question.

  I have haven´t access to the service console ESX 4.0 for some time and today I need run commands to verify information on some host bus adapters.

  I logged a user then used 'su root' to switch to the ROOT user.

  I use Putty to connect to the Service Console.

  But when I try to execute the following commands it said "Command Not Found":

  vmkload_mod

  esxcfg-module

  I read VMware KBs, that say to use these commands for this version of ESX, but I can´t do run.

  I think the answer is something very simple, but I can´t find it.

  Anyone have any ideas?

  Thank you

  Mark

  Try this command:

  quo

  as documented in http://kb.vmware.com/kb/1006573

• Installation Partition problem (allocated too expensive for the Service Console?)

  Installation Partition problem (allocated too expensive for the Service Console?)

  RAID1 (15K 146 GB SAS) on Dell R710 and VMFS is on table EQL.

  What I did during the ESX4.1 excavation, it's that I have used ALL the space in 146 GB (mainly for / and / var), after adding this ESX host to vCenter, VC and EQL ASM/VE started to complain about the following points:

  1 VC: health check of localstorage warning (only has 245 MB left on 146SAS localstorage)

  2 EQL ASM/VE: warning rootFolder folder (due to the above)

  I thought that he is authorized to use all the space for / (50 GB) and / var (50 GB) in my case for only 146 GB, I don't think I need to leave any space on the installation disc.

  Could someone share some lights here?

  Thank you

  As you can see SDS use all the SDC VMFS partition space.

  This create the alarm.

  The thing really confused me why I have to leave a space on the disk at all?

  Technically there is no reason to let the space... but also no reason to have a big service console

  Usually, you need 10 to 20% free space for each snapshot data store and Exchange files... but in your case, you will not have these files.

  If you have any problems, but you receive the alarm until you do not disable them on this specific data store.

  PS: I suggest you switch to ESXi, is quite simple and it doesn't have this strange vmdk for the "console".

  André

• Slow performance NFS (16 MB/s) of the Service Console

  I'm trying to set up an environment with ghettoVCB but I have problems with the flow to the NFS share.

  My configuration:

  ESXi host:

  ESXi 4.0.0 164009

  Reference Dell R710 with 8x300GB 10 k SAS.

  NAS server:

  Nexenta 3.1.0

  Dell PE2950 with 6x2TB Sata

  Local write on the nas performance is around 230 Mbps. tested by running these two commands in two different sessions of PuTTY:

  zpool iostat tank 5
  
  dd if=/dev/zero of=sometestfile2 bs=1024000 count=5000
  
  

  Zpool iostat output:

                 capacity     operations    bandwidth
  pool        alloc   free   read  write   read  write
  
  ----------  -----  -----  -----  -----  -----  -----
  tank        7.59G  10.9T      0      0      0      0
  tank        6.74G  10.9T      0    709      0  64.2M
  tank        8.11G  10.9T      0  2.06K      0   235M
  tank        9.62G  10.9T      0  2.07K      0   254M
  tank        10.8G  10.9T      0  1.81K      0   219M
  
  
  

  Switch dedicated for storage area network:

  Cisco 3750 with mtu 9000 system

  Nexenta hosts both ESXi are connected to the switch with network cards with Jumbo enabled frames.

  I created an NFS share and mounted as a data store in ESXi. When I run the command "dd" even the service console, I get this:

  tank        6.94G  10.9T      0    178      0  16.9M
  tank        7.03G  10.9T      0    190      0  16.2M
  tank        7.11G  10.9T      0    180      0  17.0M
  
  
  

  To test another way, I created a vmnic in the vSwitch dedicated for nfs and then attached this nic to a guest vm under Debian. I mounted the same nfs share and run the same command "dd":

  splunk01:mount 192.168.XXX.XXX:/volumes/tank/vmbackup /mnt/nas0
  splunk01:/mnt/nas0# dd if=/dev/zero of=sometestfile4 bs=1024000 count=5000
  5000+0 records in
  5000+0 records out
  5120000000 bytes (5.1 GB) copied, 56.1965 s, 91.1 MB/s
  splunk01:/mnt/nas0#
  
  
  
  
  
  

  zpool iostat output:

  admin@nas0:~$ zpool iostat tank 5
               capacity     operations    bandwidth
  
  pool        alloc   free   read  write   read  write
  ----------  -----  -----  -----  -----  -----  -----
  tank        8.73G  10.9T      0      1  5.72K   143K
  tank        8.73G  10.9T      0      0      0      0
  tank        8.73G  10.9T      0    389      0  47.5M
  tank        9.49G  10.9T      0    684      0  80.7M
  tank        4.24G  10.9T      0    702      0  84.6M
  tank        4.63G  10.9T      0    780      0  92.7M
  tank        4.63G  10.9T      0    750      0  91.1M
  tank        5.74G  10.9T      0    820      0  98.4M
  tank        6.27G  10.9T      0    729      0  87.9M
  tank        6.27G  10.9T      0    756      0  91.1M
  tank        7.28G  10.9T      0    785      0  94.9M
  tank        7.80G  10.9T      0    694      0  83.6M
  tank        7.80G  10.9T      0    801      0  96.6M
  tank        8.74G  10.9T      0    595      0  69.2M
  tank        8.74G  10.9T      0      0      0      0
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  
  

  So there is clearly no problem on the side of Nexenta.

  What I am doing wrong?

  Is there a problem with this build exakt?

  Andreas

  Hello

  you try this optimalizations in the GUI:

  1 / disable ZIL
  Settings-> preferences-> system
  Sys_zfs_nocacheflush Yes (default: No.)
  WARNING: it is dangerous without UPS

  2 / disable Nagel algoritm
  Settings-> preferences-> network
  Net_tcp_naglim_def 1 (default: 4095)

  3 / adapt for HDD SATA

  Settings-> preferences-> system
  Sys_zfs_vdev_max_pending 1 (default: 10)

  4 / disabling synchronization

  Data-> actions-> folder xxx management

  Turning off synchronization (default: Standard)

• Identify the process of the virtual machine in the Service Console

  Maybe it's a little challenging, but I need to "hang" a VM intentionally for purposes of Compliance\Qualification.  I'm trying to understand the best way to do this and my colleague suggested to connect to the service console, identify the process virtual machine running and terminate, so suspend the virtual machine.  The problem is, I'm not sure how to proceed.  Could someone point me to the light?

  Thank you very much.

  Steve

  You must know the name of the vmx file (usually it is the first name of the virtual machine).

  Then, connect SSH (or console) to your ESX and run the following command

  PS auxfww | grep 'VMXname '.

  At this point, you can locate the correct PID of the virtual machine. The first number to appear in the output is your PID.

  The PID can be used to complete the process by issuing the command kill-9 PID.

  André

• the system configuration not saved during the last stop on the service console error

  Hello

  I m getting this msg of error on the service console

  the system configuration not saved during the last stop on the service console error

  but when I tried to run some commands s troubleshoot mode according to the vmware esxcfg-boot - b, esxcfg-boot - p I got an error message like

  bad interprator usr permission denied

  I guess you follow this KB: http://kb.vmware.com/kb/1002503

  But seems like you have file system errors.

  Try to restart your system in init 1

  Then use fsck command to check your ext3 file system (remember that the file systems are not in use and use the - f option).

  André

• Change the IP address of the Service Console

  Hi, when I try to change the IP address and the address of the gateway to the Service Console NIC on the console, I always get this message:

  !!! WARNING!

  Loss of connectivity network may occur if the parameters not valid in

  Add, remove, Portgroup or IP operations.

  and nothing is changed. How is it possible to change the IP address of vswif?

  I try with the command "esxcfg-vswif!

  Thank you

  Hello

  There are two ways of CLI to chang the IP address of the service console.

  Either remove the current vswif0 and recreate it using esxcfg-swif.

  But as you must change the ip address of the service console, you can try e under method, change the entries in the file.

  for the ip address and the mask of the service console, you can change the entries in the file below.

  / etc/sysconfig/network-scipts/ifcfg-vswif0

  and for the gateway, host name using the file below

  sysconfig

  for the dns entries

  /etc/resolv.conf

  After all the changes, try to network service.

  service network restart

  Let me know if you need more information.

  -Aurelia

• I just paid my creative service cloud for a month, but there is a problem with the service, is that someone has the same problem?

  I just paid my creative service cloud for a month, but there is a problem with the service, is that someone has the same problem?

  I paid with Paypal, which is linked to my debit card and already wait two days.

  Thanks to the community

  Please read https://forums.adobe.com/thread/1499014

  -try some steps such as changing browsers and disable your firewall

  -also clear the cache of your browser if you start with a fresh browser

  -check the file hosts for blocked entries https://forums.adobe.com/thread/1912777

  http://myleniumerrors.com/installation-and-licensing-problems/creative-cloud-error-codes-w ip.

  https://helpx.Adobe.com/creative-cloud/KB/creative-cloud-desktop-application-failed.html

  http://helpx.Adobe.com/creative-cloud/KB/failed-install-creative-cloud-desktop.html

  or

  Your subscription to cloud shows correctly on your account page?

  If you have more than one email, you will be sure that you use the right Adobe ID?

  https://www.adobe.com/account.html for subscriptions on your page from Adobe

  .

  If Yes

  Some general information for a subscription of cloud

  Cloud programs don't use serial... numbers you, connect you to your cloud account paying to download & install & activate... you may need to sign out of the cloud and restart your computer and log into the cloud for things to work

  Sign out of your account of cloud... Restart your computer... Connect to your paid account of cloud

  -Connect using http://helpx.adobe.com/x-productkb/policy-pricing/account-password-sign-faq.html

  -http://helpx.adobe.com/creative-cloud/kb/sign-in-out-creative-cloud-desktop-app.html

  -http://helpx.adobe.com/x-productkb/policy-pricing/activation-network-issues.html

  -http://helpx.adobe.com/creative-suite/kb/trial--1-launch.html

  -ID help https://helpx.adobe.com/contact.html?step=ZNA_id-signing_stillNeedHelp

  -http://helpx.adobe.com/creative-cloud/kb/license-this-software.html

  .

  If no

  This is an open forum, Adobe support... you need Adobe personnel to help

  Adobe contact information - http://helpx.adobe.com/contact.html

  Chat/phone: Mon - Fri 05:00-19:00 (US Pacific Time)<=== note="" days="" and="">

  -Select your product and what you need help with

  -Click on the blue box "still need help? Contact us. "

• How to control the service console in ESX?

  How to control the service console in ESX?

  http://www.Petri.co.il/5-critical-VMware-ESX-CLI-network-commands.htm

  http://download3.VMware.com/VMworld/2006/mdc9694.PDF

  http://download3.VMware.com/VMworld/2006/mdc9807.PDF

  http://download3.VMware.com/VMworld/2006/tac0028.PDF

  http://download3.VMware.com/VMworld/2006/tac9689-b.PDF

  http://download3.VMware.com/VMworld/2006/labs2006/VMworld.06.Lab04-performance-manual.PDF

  http://www.RTFM-ed.co.UK/

  PS: If you have found useful messages then please leave a few points

  André

• ESX 3.5: copy files using the service console from a network share to the esx host data store

  Hello

  I wonder. Is there a command that I can run the service console that would allow me to copy a file from a network share on the data store on the esx host?

  Eric

  If sharing is a Windows, you can also use smbclient within the service console and ride sharing.

  André

  * If you found this device or any other answer useful please consider awarding points for correct or helpful answers

• Problem with password reset link - "there is a temporary problem with the service. Please try again. If you continue to receive this message, try again later. »

  Hello, account Windows Live from my wife was hacked a week ago and has been used to send many spam emails. As a result, his account has been disabled or closed (we are not sure). Whenever she asks to reset a password and a link sent to a different e-mail account, when she clicked it gets this message 'there is a temporary problem with the service. Please try again. If you continue to receive this message, try again later. "She is tried repeatedly, but get the same message. Someone knows how to go beyond that, so she can recover her account? Thank you.

  Hello BBB34,

  The best place to ask your question of Windows Live is inside Windows Live help forums. Experts specialize in all things, Windows Live, and would be delighted to help you with your questions. Please choose a product below to be redirected to the appropriate community:

  Windows Live Mail

  Windows Live Hotmail

  Windows Live Messenger

  Looking for a different product to Windows Live? Visit the home page Windows Live Help for the complete list of Windows Live forums to www.windowslivehelp.com.

• How can I add an ID related when I get this message (there is a temporary problem with the service. Please try again. If you continue to receive this message, try again later.) ?

  How can I add an ID related when I get this message (there is a temporary problem with the service. Please try again. If you continue to receive this message, try again later.) ?

  Hello

  an answer your other thread

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_vista-networking/why-do-i-keep-getting-your-Windows-Live-ID-cant-be/268ff99c-E459-E011-8dfc-68b599b31bf5?page=1&TM=1301396733390#footer

• Adding an IP to the service console more

  Hi team,

  We have a race ESX 4 and the service console has already been configured with an IP address, I would like to add an IP more (another beach) so this service console must be accessible by both intellectual property.

  Now my console IP service is 172.18.111.155 with a subnet mask of 255.255.255.0, GW - 172.18.111.1

  Now, I need to add another IP 172.18.105.45 Beach IE with a subnet mask of 255.255.254.0. GW - 172.18.104.1

  Could you please let me know if possible, if so how can be done.

  Thank you

  Akhi

  Hello

  Next, you create just a new vSwitch with your 2nd service console using the dedicated bear. Marking will be on the side of the physical switch.

  If this host is in a HA Cluster, you may receive warnings about redundancy.

  Seeing that it is your 2nd service console, you can remove these messages. Watch http://kb.vmware.com/selfservice/microsites/search.do?language=en_US&cmd=displayKC&externalId=1004700

  Please allow points for correct answers