problems with side-by-side configuration

Similar Questions

• problems with vpn firewall/proxy configuration

  Hello

  I want to access vpn through firewall/proxy (Client VPN) client-side.

  I installed the vpn gateway as firewall pix 515 using Microsoft CA IKE SA.

  I want to establish the vpn tunnel to my vpn through a proxy/firewall client.

  I tried in some places of vpn client where the firewall acts as a linux machine in which he allowed with the ipsec and NAT esp feature. Its works perfectly. But only one concurrent vpn client. Also the first tunnel vpn disconnects when the second user tries without knowing the first established tunnel.

  I heard that we can drive this problem using "NAT Taversal" mode which is available in version ios 6.3 as concentrator 3000 Cisco pix.

  I want to know how NAT Traversal can solve my problem in which multiple concurrent users without support nat esp in a configuration only one simultaneous user without support nat esp in a configuration of firewall/proxy or firewall/proxy.

  Thank you

  Karthikeyan V

  The VPN client is able to detect that he's been through a NAT/PAT device on the way to the hub/PIX, and then if both ends support it, they will automatically start NAT - T and encapsulate the IPSec packets in UDP port 4500 packets. These can then be NAT would properly and you will not get disconnections or problems you currently see.

  You don't see that a client can connect and customers being disconnected when the other connects it is your PAT instrument cannot process the ISAKMP and IPSec packets correctly. It is a fairly common symptom.

  PIX v6.3 code will support NAT - T, should be available in March sometime.

• Problem with the Toshiba 32SL738F configuration menu

  I can t get into the configuration menu of the TV (model 32SL738F). I have no options to take when I get in the configuration of the remote control. It is possible to have several code (PIN)? I don t know where to go. Thank you

  rontu_florin, depending on the specific English operating manual, the code of universal security (password), (at page 55 in the 'Q & A' section), is * 1276.*

  The factory default security code or password is * 0000 * (i.e. four zeroes)

  I am unable to assist you in how to enter codes if you do not see the options, I suggest you if you enter the menu of English language there might be a possibility that some options that have been hidden can (CAN ONLY!), can be consulted, this was found by another owner, with a different problem , in another thread in this forum.

  _I can only suggest, read the carefully_ manual...

  donhe7

• 'Problem with the paging file Configuration '.

  I use a Windows 7 Ulitmate 64 bit vm on my 15 "MacBook Pro (Retina Display). I attributed to the VM 1 core processor and 2 GB of RAM. His virtual HD is 64.2 GB (molten ' preference > general ", but molten" Preferences > hard drive "the slider is set to 40 GB.) In "Preferences > general" there is no recoverable space. Looking at the control panel of Windows 7, I see that there is barely 1 GB free of my 40 GB drive.

  The SSD on Mac is 250 GB and has 67 GB of free, so I guess I could until hard drive of the virtual machine to 60 or 70 GB of space and not paralyze the Mac operating system, and that I can do that by stopping the virtual machine deletion of snapshots and then mount the virtual HD size with the cursor before restarting.

  Moreover, this is the message I get from Windows at startup. Curiously, it is only after I have connected to my account, not as part of the start-up procedure, and it reappears if I log in. I don't have an another user account on the machine, but I guess that the problem comes from the virtual HD is almost full:

  Yes, deletion of snapshots and enlarge the size of the virtual hard disk (and virtual partition) will give you additional disk space on the prompt to work with but how is virtual memory configured in the Windows 7 guest?  You can watch that too.

• Problems with the 'Grid entity' configuration consistency

  I have difficulty getting the configuration work "Entity grid" consistency. I'm on Oracle Version consistency 3.6.0.4 Build 19111. I carefully followed the instructions for the third scenario configuration consistency documented on the page "JPA on the grid" [url http://docs.oracle.com/cd/E14571_01/doc.1111/e16596/tlcgd003.htm#CHDGGGAJ] here. I will include excerpts from the records, but I think that I have been following the docs. I must be missing something that the docs report directly? Any ideas would be greatly appreciated.
  
  The problem I encounter is that when this 'Grid entity' coherence mode is used, the entities are not reading from the database when the application starts. The application behaves as if there is absolutely no data in the database, even if I know that I have lines in tables to backup my entities. In my test dummy application, I also have problems persistent entities. If I temporarily disable consistency commenting annotations {noformat}@Customizer{noformat} entity everything works perfectly (DataSet starting loads from the database as expected and new entities are correctly preserved). If I change to the "grid + hidden +" things configuration seems to work fine. But it's not ideal because we want the features of read/write of entityof the grid.
  
  Here is my file of coherence-cache - config.xml (corresponds almost exactly to the documentation):

  <?xml version='1.0'?>
  <cache-config xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance"
     xmlns="http://xmlns.oracle.com/coherence/coherence-cache-config"
     xsi:schemaLocation="http://xmlns.oracle.com/coherence/coherence-cache-config coherence-cache-config.xsd">
    <caching-scheme-mapping>
      <!--
        Map all entity classes to the eclipselink-distributed-readwrite scheme
  -->
      <cache-mapping>
        <cache-name>*</cache-name>
        <scheme-name>eclipselink-distributed-readwrite</scheme-name>
      </cache-mapping>
    </caching-scheme-mapping>
    <caching-schemes>
      <distributed-scheme>
        <scheme-name>eclipselink-distributed-readwrite</scheme-name>
        <service-name>EclipseLinkJPAReadWrite</service-name>
        <!--
          Configure a wrapper serializer to support serialization of relationships.
        -->
        <serializer>
            <instance>
               <class-name>oracle.eclipselink.coherence.integrated.cache.WrapperSerializer</class-name>
            </instance>
        </serializer>
        <backing-map-scheme>
          <read-write-backing-map-scheme>
            <internal-cache-scheme>
              <local-scheme/>
            </internal-cache-scheme>
            <!-- 
               Define the cache scheme 
             -->
            <cachestore-scheme>
              <class-scheme>
                <class-name>oracle.eclipselink.coherence.integrated.EclipseLinkJPACacheStore</class-name>
                <init-params>
                  <!-- This param is the entity name -->
                  <init-param>
                    <param-type>java.lang.String</param-type>
                    <param-value>{cache-name}</param-value>
                  </init-param>
                  <!-- This param should match the persistence unit name in persistence.xml -->
                  <init-param>
                    <param-type>java.lang.String</param-type>
                    <param-value>test-pu</param-value>
                  </init-param>
                </init-params>
              </class-scheme>
            </cachestore-scheme>
          </read-write-backing-map-scheme>
        </backing-map-scheme>
        <autostart>true</autostart>
      </distributed-scheme>
    </caching-schemes>
  </cache-config>

  Persistence.XML:

  <?xml version="1.0" encoding="windows-1252" ?>
  <persistence xmlns="http://java.sun.com/xml/ns/persistence"
               xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance"
               xsi:schemaLocation="http://java.sun.com/xml/ns/persistence http://java.sun.com/xml/ns/persistence/persistence_1_0.xsd"
               version="1.0">
    <persistence-unit name="test-pu">
      <provider>org.eclipse.persistence.jpa.PersistenceProvider</provider>
      <jta-data-source>jdbc/WineDS</jta-data-source>
      <non-jta-data-source>jdbc/WineDS</non-jta-data-source>
      <class>datagridtest.WineEntity</class>
      <properties>
        <property name="eclipselink.target-server" value="WebLogic_10"/>
        <property name="eclipselink.target-database" value="Oracle11"/>
         <!--<property name="eclipselink.ddl-generation" value="create-tables"/>-->
      </properties>
    </persistence-unit>
  </persistence>

  entity class:

  @Entity(name="Wine")
  @NamedQueries({
    @NamedQuery(name = "Wine.findAll", query = "select o from Wine o"),
    @NamedQuery(name = "Wine.findByRegion", query = "select o from Wine o where o.region = :region"),
    @NamedQuery(name = "Wine.findByVintage", query = "select o from Wine o where o.vintage = :vintage"),
    @NamedQuery(name = "Wine.findByWinery", query = "select o from Wine o where o.winery = :winery")
  })
  @SequenceGenerator(name = "Wine Seq", sequenceName = "WINE_SEQ", allocationSize = 50, initialValue = 50)
  @Customizer(CoherenceReadWriteCustomizer.class)
  public class WineEntity implements Serializable {
       @Id
       @GeneratedValue(strategy = GenerationType.SEQUENCE, generator = "Wine Seq")
       private Integer id;
       @Version
       private Integer version;
       
       private String name;
       
       private int vintage;
       
       private String region;
       
       private String winery;
       
       typical getters and setters follow...
       ....

  Extracts of EJB:

  @Stateless(name = "SessionEJB", mappedName = "PortletProducerApplication-DataGridTest-SessionEJB")
  public class SessionEJBBean implements SessionEJBLocal {
       @PersistenceContext(unitName="test-pu")
       private EntityManager em;
       
       ...
       
       public List<WineEntity> findAllWines() {
            TypedQuery<WineEntity> allWinesQuery = em.createNamedQuery("Wine.findAll", WineEntity.class);
            return allWinesQuery.getResultList();     
       }
       
       ...
       
  }

  (IWLS) server logs:

  <Jun 25, 2012 3:54:41 PM EDT> <Notice> <EclipseLink> <BEA-2005000> <2012-06-25 15:54:41.686--ServerSession(1768045153)--EclipseLink, version: Eclipse Persistence Services - 2.1.3.v20110304-r9073> 
  <Jun 25, 2012 3:54:41 PM EDT> <Notice> <EclipseLink> <BEA-2005000> <2012-06-25 15:54:41.688--ServerSession(1768045153)--Server: 10.3.5.0> 
  <Jun 25, 2012 3:54:42 PM EDT> <Notice> <EclipseLink> <BEA-2005000> <2012-06-25 15:54:42.142--ServerSession(1768045153)--file:/C:/Users/EDITED/AppData/Roaming/JDeveloper/system11.1.1.5.37.60.13/o.j2ee/drs/TestApp/DataGridTestEJB.jar/_test-pu login successful> 
  2012-06-25 15:54:42.502/58.626 Oracle Coherence 3.6.0.4 <Info> (thread=[ACTIVE] ExecuteThread: '4' for queue: 'weblogic.kernel.Default (self-tuning)', member=n/a): Loaded operational configuration from "jar:file:/C:/Oracle/Middleware/oracle_common/modules/oracle.coherence_3.6/coherence.jar!/tangosol-coherence.xml"
  2012-06-25 15:54:42.513/58.637 Oracle Coherence 3.6.0.4 <Info> (thread=[ACTIVE] ExecuteThread: '4' for queue: 'weblogic.kernel.Default (self-tuning)', member=n/a): Loaded operational overrides from "jar:file:/C:/Oracle/Middleware/oracle_common/modules/oracle.coherence_3.6/coherence.jar!/tangosol-coherence-override-dev.xml"
  2012-06-25 15:54:42.516/58.640 Oracle Coherence 3.6.0.4 <D5> (thread=[ACTIVE] ExecuteThread: '4' for queue: 'weblogic.kernel.Default (self-tuning)', member=n/a): Optional configuration override "/tangosol-coherence-override.xml" is not specified
  2012-06-25 15:54:42.524/58.648 Oracle Coherence 3.6.0.4 <D5> (thread=[ACTIVE] ExecuteThread: '4' for queue: 'weblogic.kernel.Default (self-tuning)', member=n/a): Optional configuration override "/custom-mbeans.xml" is not specified
  
  Oracle Coherence Version 3.6.0.4 Build 19111
   Grid Edition: Development mode
  Copyright (c) 2000, 2010, Oracle and/or its affiliates. All rights reserved.
  
  2012-06-25 15:54:42.673/58.797 Oracle Coherence GE 3.6.0.4 <Info> (thread=[ACTIVE] ExecuteThread: '4' for queue: 'weblogic.kernel.Default (self-tuning)', member=n/a): Loaded cache configuration from "file:/C:/workspaces/spaces_branch/TestApp/DataGridTest/src/coherence-cache-config.xml"
  2012-06-25 15:54:43.360/59.484 Oracle Coherence GE 3.6.0.4 <D4> (thread=[ACTIVE] ExecuteThread: '4' for queue: 'weblogic.kernel.Default (self-tuning)', member=n/a): TCMP bound to /172.30.112.202:8088 using SystemSocketProvider
  2012-06-25 15:54:46.747/62.871 Oracle Coherence GE 3.6.0.4 <Info> (thread=Cluster, member=n/a): Created a new cluster "cluster:0xC4DB" with Member(Id=1, Timestamp=2012-06-25 15:54:43.377, Address=172.30.112.202:8088, MachineId=49866, Location=site:EDITED,machine:EDITED,process:10776, Role=WeblogicServer, Edition=Grid Edition, Mode=Development, CpuCount=4, SocketCount=2) UID=0xAC1E70CA000001382535DD31C2CA1F98
  2012-06-25 15:54:46.757/62.881 Oracle Coherence GE 3.6.0.4 <Info> (thread=[ACTIVE] ExecuteThread: '4' for queue: 'weblogic.kernel.Default (self-tuning)', member=n/a): Started cluster Name=cluster:0xC4DB
  
  Group{Address=224.3.6.0, Port=36000, TTL=4}
  
  MasterMemberSet
    (
    ThisMember=Member(Id=1, Timestamp=2012-06-25 15:54:43.377, Address=172.30.112.202:8088, MachineId=49866, Location=site:EDITED,machine:EDITED,process:10776, Role=WeblogicServer)
    OldestMember=Member(Id=1, Timestamp=2012-06-25 15:54:43.377, Address=172.30.112.202:8088, MachineId=49866, Location=site:EDITED,machine:EDITED,process:10776, Role=WeblogicServer)
    ActualMemberSet=MemberSet(Size=1, BitSetCount=2
      Member(Id=1, Timestamp=2012-06-25 15:54:43.377, Address=172.30.112.202:8088, MachineId=49866, Location=site:EDITED,machine:EDITED,process:10776, Role=WeblogicServer)
      )
    RecycleMillis=1200000
    RecycleSet=MemberSet(Size=0, BitSetCount=0
      )
    )
  
  TcpRing{Connections=[]}
  IpMonitor{AddressListSize=0}
  
  2012-06-25 15:54:46.809/62.933 Oracle Coherence GE 3.6.0.4 <D5> (thread=Invocation:Management, member=1): Service Management joined the cluster with senior service member 1
  2012-06-25 15:54:47.155/63.279 Oracle Coherence GE 3.6.0.4 <D5> (thread=DistributedCache:EclipseLinkJPAReadWrite, member=1): Service EclipseLinkJPAReadWrite joined the cluster with senior service member 1
  INFO: Found persistence provider "org.eclipse.persistence.jpa.PersistenceProvider". OpenJPA will not be used.
  INFO: Found persistence provider "org.eclipse.persistence.jpa.PersistenceProvider". OpenJPA will not be used.
  [EL Info]: 2012-06-25 15:54:47.351--ServerSession(1901778202)--EclipseLink, version: Eclipse Persistence Services - 2.1.3.v20110304-r9073
  [EL Info]: 2012-06-25 15:54:47.351--ServerSession(1901778202)--Server: 10.3.5.0
  [EL Info]: 2012-06-25 15:54:47.551--ServerSession(1901778202)--EclipseLinkCacheLoader-test-pu login successful

  And the error when you try to make persistent the new entity:

  javax.ejb.TransactionRolledbackLocalException: Error committing transaction:; nested exception is: javax.persistence.OptimisticLockException: Exception [EclipseLink-5004] (Eclipse Persistence Services - 2.1.3.v20110304-r9073): org.eclipse.persistence.exceptions.OptimisticLockException
  Exception Description: An attempt was made to update the object [datagridtest.WineEntity@1c59a6cc], but it has no version number in the identity map. 
  It may not have been read before the update was attempted. 
  Class> datagridtest.WineEntity Primary Key> 2,050
       at weblogic.ejb.container.internal.EJBRuntimeUtils.throwTransactionRolledbackLocal(EJBRuntimeUtils.java:238)
       at weblogic.ejb.container.internal.EJBRuntimeUtils.throwEJBException(EJBRuntimeUtils.java:136)
       at weblogic.ejb.container.internal.BaseLocalObject.postInvoke1(BaseLocalObject.java:650)
       at weblogic.ejb.container.internal.BaseLocalObject.__WL_postInvokeTxRetry(BaseLocalObject.java:455)
       at weblogic.ejb.container.internal.SessionLocalMethodInvoker.invoke(SessionLocalMethodInvoker.java:52)
       at datagridtest.SessionEJB_qxt9um_SessionEJBLocalImpl.mergeWineEntity(Unknown Source)

  So just to sum up, I currently see two problems: 1) no data from the database consistency and implementation — why not consistency out of database? and (2) what's this persistent mistake on OptimisticLockException? Thanks again for any help.

  JPQL API criteria or both will result in coherence filters when using GridRead or GridEntity.
  TopLink grid has no way of knowing if the data in the cache are sufficient to satisfy the query, for example based on the provided query TopLink grid would determine how between a user with no book and insufficient. Your application will need to determine that not enough has been stored in the cache or to perform an initial charge in bulk for a particular user to redirect the request to the database programmatically. Queries of grid can easily be redirected to the database by setting the IgnoreDefaultRedirector on the query using query.setHint (QueryHints.QUERY_REDIRECTOR, new IgnoreDefaultRedirector()); Read from the database of entities will be automatically pushed to the consistency.

• Strange problem with Vista Home premium configuration update

  Just bought a Toshiba Satellite Pro L300-1AI which was preloaded with Vista Home Premium.

  Clicked on configure updates on the front screen and he entered a loop that says: Configuring updates: stage 3 of 3-0% complete. Do not turn off your computer.

  Every 5 minutes or so then stops and restarts with the same message. I left on for 8 hours, so can not believe he needs for this long. Just tried to set off, but when you restart it defaults as shown above.

  Please advise... even if you can get me right back to the normal screen before

  Hello

  Try please start your computer in safe mode and restore your operating system to an earlier time (before the update). Maybe this will help.

  In the future be careful with updates. I recommend you to disable the automatic update. Just check the list with updated supply and install important and recommended only. Disable all optional updates. You don't need them.

• What is the problem with my controlfile multiplexing configuration?

  Originally, my database was using the controlfile multiplexing configuration default and it worked perfectly fine.
  But then, right now, it no longer works.
  When I try to mount the database, it always throws below error.

  ORA-00205: error in identifying control file, check alert log for more info

  and when I look to the top of the alert.log, it shows:

  ORA-00202: control file: 'E:\ORACLE\PRODUCT\10.2.0\ORADATA\ORCL\CONTROL01.CTL, E:\ORACLE\PRODUCT\10.2.0\ORADATA\ORCL\CONTROL02.CTL, E:\ORACLE\PRODUCT\10.2.0\ORADATA\ORCL\CONTROL03.CTL'
  ORA-27041: unable to open file
  OSD-04002: unable to open the file
  O/S-Error: (OS 123) he system cannot find the path specified.

  But I guarantee you that these files are there.
  
  Then, I start to manipulate the parameter CONTROL_FILES and got below:

  ---When all three controlfiles are included in parameter
  SQL> alter system set control_files='E:\ORACLE\PRODUCT\10.2.0\ORADATA\ORCL\CONTROL01.CTL, E:\ORACLE\PRODUCT\10.2.0\ORADA
  TA\ORCL\CONTROL02.CTL, E:\ORACLE\PRODUCT\10.2.0\ORADATA\ORCL\CONTROL03.CTL' scope=spfile;
  
  System altered.
  
  SQL>
  SQL> startup force;
  ORACLE instance started.
  
  Total System Global Area  612368384 bytes
  Fixed Size                  1250428 bytes
  Variable Size             218106756 bytes
  Database Buffers          385875968 bytes
  Redo Buffers                7135232 bytes
  ORA-00205: error in identifying control file, check alert log for more info
  
  ---When only two of them are included in parameter
  SQL> alter system set control_files='E:\ORACLE\PRODUCT\10.2.0\ORADATA\ORCL\CONTROL01.CTL, E:\ORACLE\PRODUCT\10.2.0\ORADA
  TA\ORCL\CONTROL02.CTL' scope=spfile;
  
  System altered.
  
  SQL> startup force;
  ORACLE instance started.
  
  Total System Global Area  612368384 bytes
  Fixed Size                  1250428 bytes
  Variable Size             218106756 bytes
  Database Buffers          385875968 bytes
  Redo Buffers                7135232 bytes
  ORA-00205: error in identifying control file, check alert log for more info
  
  --only one is included
  SQL> alter system set control_files='E:\ORACLE\PRODUCT\10.2.0\ORADATA\ORCL\CONTROL01.CTL' scope=spfile;
  
  System altered.
  
  SQL> startup force;
  ORACLE instance started.
  
  Total System Global Area  612368384 bytes
  Fixed Size                  1250428 bytes
  Variable Size             218106756 bytes
  Database Buffers          385875968 bytes
  Redo Buffers                7135232 bytes
  Database mounted.
  Database opened.
  SQL>

  Why it's happening? Just in case control02.ctl, control03.ctl are broken, I have manually copy the control01.ctl and rename it to control02.ctl and control03.ctl, but still does not.
  When I copy control01 to 02, 03, I did stop the database, so there is no problem of incompatibility.
  
  So, what could be the reason? someone has an idea?
  
  Thank you

  Hello
  You actually use the incorrect syntax for alter system. Use it like this:

  ALTER system set control_files='E:\ORACLE\PRODUCT\10.2.0\ORADATA\ORCL\CONTROL01. CTL ',' E:\ORACLE\PRODUCT\10.2.0\ORADA
  TA\ORCL\CONTROL02. CTL ',' E:\ORACLE\PRODUCT\10.2.0\ORADATA\ORCL\CONTROL03. CTL' scope = spfile;

  concerning

• Problems with the permissions/security configuration XP Home Edition - can not download any software!

  I have Norton 360 on my computer.  OS is XP Home Edition. My computer very slow in normal mode (not in SafeMode if) I chatted for 4 hours with the help of Norton Tech... try to allow remote access, which could not happen because the piece of software that must be downloaded has been blocked, and I got a pop-up box saying that security settings do not need to download this software.  Then we tried to download Norton360 to reinstall it, and I got the same message.

  Since Explorer crashes constantly, and I'm very furstrated with it, I decided to try the same Firefox downloads.  Software download, but trying to run them, I got a message syaing that I don't have permission to run them.

  What should I do?  I'm NOT a computer guru - actually I'm computer disabled... Please help me.

  Hi IG18912,

  · Have you logged on as a computer administrator?

  · What is the version of Internet explorer, you have installed?

  1. follow the procedure that allows the file below to download in Internet Explorer.

  a. open Internet Explorer.

  b. click on tools, then options.

  c. click on the Security tab.

  d. Select the Internet Zone.

  e. click on the custom level button and then scroll down to download.

  f. be sure to enable the download of the file.

  g. click on apply and Ok

  h. restart Internet Explorer and see if that helps.

  2. in addition, follow the steps in the link below: error message when you try to open the the Task Manager on a Windows XP-based computer: "Task manager has been disabled by your administrator":http://support.microsoft.com/kb/913623

  3. on-line virus scanner and check if any malware or virus detected on the computer activity. You can run the scan for viruses online from the link below:http://onecare.live.com/site/en-us/default.htm

  With regard to:

  Samhrutha G S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• problem with the instanceconfig.xml configuration

  Hello
  I am trying to add a few additional options in my instanceconfig.xml file. But every time I have to add changes (as < ServerInstance > < AllowRememberPassword > n < / AllowRememberPassword >) and restart the service server OBI and OBI, service of presentation server presentation server service is does not start.
  And when I cancel the service changes presentation server will begin end.
  Please give me your point of view to address this issue.
  
  Thanks and greetings
  Suresh.

  Hello...

  Delete the tag and paste only...
  NO.

  This should paste before
  

  It works for me

  Mark as correct if it is correct ;)

  Good luck

  Thank you & best regards
  Kishore Guggilla

  Published by: Kishore Guggilla on October 22, 2008 12:54

• Windows live messenger... having problems with by-side config

  original title: windows live messenger

  problems with side-by-side config nobody knows nothing about it pls

  problems with side-by-side config nobody knows nothing about it pls

  Messenger - side by side configuration error

  Start button > Search box, type regedit > C: key > (uac prompt) >

  expand (click the pointer before) HKET_CURRENT_USER >
  expandSoftware >
  expandMicrosoft >
  expandMSNMessenger >
  Expand PerPassportSettings > under PerPassportSettings, find 2 folders with a series of numbers > delete the two folders including their subfolders > window regedit.
  Restart the Messenger.

  If the above does not help, please repost in Windows Live Solution center - forum Messenger - Messenger discussions section

  http://windowslivehelp.com/forums.aspx?ProductID=2

• Problem with the Cisco VPN and Vista client

  Hello

  I have an easy VPN server configured on a c2811 and users use the Cisco VPN client. Lately, I have users running Windows Vista 64 bit and I need to know what is the correct version of the vpn client, I have to use and the compatibility problems with the server, I configured.

  Thank you and best regards.

  Cisco VPN Client doesn't have any version that is compatible with Vista 64 bit OS. The only customer that Cisco has released that supports the 64 bit OS's AnyConnect, but it is only supported on the CISCO ASA Appliance

• Problem with the controls side by side

  Hello

  I have a problem with a laben and a toggle button.

  I want to show them side by side, but the label must be on the right side and toggle the button on the left side.

  so when I turn my phone into landscape mode is expected to increase the space between them.

  Here is my sample Code, but I does not work as I want it.

          Container {
              layout: StackLayout {
                  orientation: LayoutOrientation.LeftToRight
  
              }
              Label {
                  text: qsTr("Public")
                  textStyle {
                      base: SystemDefaults.TextStyles.TitleText
                  }
              }
              ToggleButton {
  
              }
  
          }
  

  Use code below for your need

  {Of container
  layout: {DockLayout}

  }
  {Of container
  horizontalAlignment: HorizontalAlignment.Left
  {Label
  text: qsTr ("Public")
  textStyle {}
  Base: SystemDefaults.TextStyles.TitleText
  }
  }
  }
  {Of container
  horizontalAlignment: HorizontalAlignment.Right
  ToggleButton {}

  }
  }
  }

  Press on as if that solves your problem and mark it as resolved.

• photos of the iPhone are on the side and I can not turn because theres a problem with the property file

  Photos imported from my iphone came on the side and when I turn and try to save, it won't let me save it like that saying "windows Photo Viewer cannot save changes to this picture because there is a problem with the pictures of file properties". What should I do?

  I don't know if the following links answer your question, but
  they may be worth a visit:

  Good luck and * proceed at your own risk *.

  FWIW... There is a very long discussion (several pages) to the
  following link:

  Cannot change the imported iPhone 4S photo
  https://discussions.Apple.com/thread/3444951?start=0&TSTART=0

  More Discussion

  iPhone 4S image properties is not compartible with Windows?
  Editing can be done on the computer due to the error
  "Windows Photo Viewer cannot save changes to this picture.
  because there is a problem with the properties of the image file".
  Any help?
  https://discussions.Apple.com/message/17291884#17291884

  More Discussion:

  We cannot turn a few photos in Windows 7 (but can turn others)
  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-pictures/cant-rotate-some-photos-in-Windows-7-but-can/3a809845-9144-4BB1-9bb3-ab4f5b856524

  A simple solution is to open the photos in paint or most other
  digital image editor and modify it.

  Some people have reported success using the following free download
  to remove the metadata.

  Property restrictions stripper iphone 4S (JPEG & PNG Stripper)
  http://www.SteelBytes.com/?mid=30&cmd=download&PID=15

  Here's a way to turn...

  Easily turn locked iPhone 4 and 4 s Photos in Windows 7 with
  the rotator Lossless JPEG free
  http://www.daleisphere.com/easily-rotate-locked-iPhone-4-and-4S-photos-in-Windows-7-with-the-free-JPEG-lossless-Rotator/

  Free download JPEG Lossless rotating
  http://annystudio.com/software/jpeglosslessrotator/

• Windows 7 Causes of security errors - Invalid SIDS - problem with loading of programs such as Adobe Flash

  I discovered a bug in my Windows 7 (64-bit) that causes security errors in my system.  I honestly do not know or understand how these mistakes happened.  For example, my system lists the group "power users ^ 0' and 'Power users' (the latter should of course)."  I have never tested with the accounts system, not to mention the well known windows accounts.
  Even when I try to delete the group "power users ^ 0' the system replied that he could not remove a well-known group."  This isn't a well-known group.  The Group initially appeared in 'users and groups' within the 'computer management '.  I made a few changes to the security in the registry settings to try to fix my system, but the group no longer appears in "computer Management\Users and groups."  It appears when I look at the 'properties' for a user and select ' Add/search' when I try to add a group to the user. »
  Regarding Adobe Flash, it does not when I am connected with a normal user account.  It does not load when I log in as an administrator (on the same machine).  So I suspect there is a security problem in the registry which prevents Adobe Flash to load for a regular user.  What me stem, is that when I go there and install Adobe Flash for a normal user (Yes, he invites me to run the installation as long as the administrator - date which I enter the password to continue the installation, which runs without error reported).  The installation of Adobe Flash completed successfully for the user as an Explorer window showing the installation of Adobe Flash successfully, I proceed to access any site that requires Adobe Flash to be installed on the client computer and the site if poster correctly - flash loads fine.  Now, if log out me of the account of user and re - login under the same user on this computer, even when the user has just installed Adobe Flash, it loads is no longer!  When I navigate to a site that requires Adobe Flash, it generates an error indicating that Adobe Flash must be installed!  Curiously, when I connect as administrator, Adobe Flash loads very well!  For me, Windows 7 displays security system errors / makes me crazy.  I would be grateful if I get assistance for this problem.   All system errors have focused on SIDS invalid, invalid years system well-known accounts created by Windows 7.  In the meantime, I connect as administrator because he never complains you need to install Adobe Flash.
  Help, please!

  Thank you
  E-mail address is removed from the privacy *... com

  I decided to do a clean reinstall of my computer Windows 7 (64 bit)...  Nevertheless, I think that I think I know when the error with the "Power User ^ 0' saw the light of day..."  When I was rebuilding my machine with a fresh install of Windows 7 (with a full format my system drive), I noticed that when I renamed my machine (as everyone would expect to see), I inspected the "users and groups" in "Computer management" and low and has appeared the "power users ^ 0' group."  I believe that this has happened during the time where I've renamed my machine.   I have never messed with the creation of groups or something of the sort.  I am amazed that such a simple task would result in such a mistake.  As for my problem with impossible to load Adobe Flash, that the error has been removed, but I don't see how it existed in the first place.  I do not understand why Microsoft publishes several buggy instead of solidification Windows 7 systems.

  Thank you for your help,

  ~ sreyes27

• Error message: "the application failed to start because its side-by-side configuration is incorrect." How can I solve this problem?

  Program does not start. Error message "could not start because its side-by-side configuration is incorrect." How can I solve this problem?

  Program does not start. Error message "could not start because its side-by-side configuration is incorrect." How can I solve this problem?

  Solved!

  http://answers.Microsoft.com/en-us/windowslive/Forum/Messenger-wlinstall/the-application-has-failed-to-start-because-its/3f8a8186-9E97-4962-BE5D-b453b1597a78?tab=AllReplies#tabs