Pwerconnect 6224: vlan client computers do not receive the ip address of DHCP server on a different VLAN
Hello
I have a prolem routing dhcp requests between the vlan management where DHCP server resides and the other VLANs.
I have the scenario of base with three VLANS: vlan 10 (management vlan), 20, 30, configured on a Powerconnect 6224 switch L2 mode. This switch is connected to a pfsense router. The router is configured at the package of road between the VLANS and it does it well.
In Vlan 10, I have a configured DHCP server to use the ip addresses of all the VLANS (10, 20, 30). VLAN 10 client computers receive ip address but not others from other VLANs.
When I put the ip address in the appropriate range of VLANs manually on computers, I ping the server and I have connectivity.
This suggests that the problem is with the dhcp package.
The following is the configuration of the switch:
Configure
database of VLAN
VLAN 10,20,30
VLAN 1 1 routing
VLAN 20 2 routing
VLAN 30 3 routing
output
SNTP server time.nist.gov
clock timezone 1 minutes 0
battery
1 1 member
2 2 Member
output
DHCP IP address
IP address vlan 10
name of the IP-server 172.16.10.1
bootpdhcprelay cidridoptmode
interface vlan 1
Routing
IP 172.16.1.1 255.255.255.0
output
interface vlan 20
Routing
address 172.16.20.1 IP 255.255.255.0
output
interface vlan 30
Routing
IP 172.16.30.1 255.255.255.0
output
level of 20fc49459a1898b923ed3ec7b3e81276 user name 'admin' password encrypted 15
No spanning tree
spanning tree priority 0
l2relay DHCP
DHCP l2relay VLANs 10, 20-30
DHCP l2relay circuit-id VLANs 10, 20-30
!
interface ethernet 1/g2
l2relay DHCP
switchport access vlan 20
output
!
interface ethernet 1/g3
l2relay DHCP
switchport access vlan 30
output
!
interface ethernet 1/g21
switchport access vlan 10
output
!
interface ethernet 1/g22
switchport access vlan 10
output
!
interface ethernet 1/g23
switchport access vlan 10
output
!
interface ethernet 1/g24
switchport mode trunk
switchport trunk allowed vlan add 10,20,30
output
Server SNMP community EyesOfNetwork ro
SNMP-server community public ro
output
I followed the instructions in the powerconnect 6224 user guide, but no progress on this issue.
Any help will be be grateful.
Thank you
Zoubeir
The DHCP server stores information that could be useful? May need to configure monitoring ports and something as wireshark to monitor DHCP packets. This would help determine where the package is stopping.
example:
Console (config) #monitor session 1 source interface 1/g8
Console (config) #monitor session 1 destination interface 1/g10
session mode 1 #monitor console (config)
right now I don't see anything in the config of the switch that stands out. If the DHCP server is configured for option 82, then you will need to include the following command on the switch.
Example:
Trust l2relay console #dhcp (config-if-1/g1)
But I don't think that's our scenario here.
Tags: Dell Switches
Similar Questions
-
I'm impossible to connect, and you do not receive the password email when I ask.
I'm trying to connect with the stored user name and password, but they do not work. I tried new password sent by e-mail, 5 or 6 times in the last 24 hours, but I never received an email.
Connect to what?
The extent of the not received the email, have you looked into the Spam folder?
-
did not receive the product code for age of empires
I downloaded Age of Empires 3, but have not received the product code and can't install. Who should I contact?
Thank you
Hello
I'd say contact Microsoft phone support for assistance.
-
Did not receive the last updates of Windows XP.
Original title: update XP final
I have not received the final updates for XP today. I tried to install them manually but can't because support for XP is completed. Is there a way I can get them?
Yes, as of April 8, 2014, these are the latest updates for Windows XP, but since Microsoft has confirmed publicly that they will continue to develop and test the Windows XP security updates - since they are obliged under contract to the many millions of PCs under enterprise agreements including groups like the Government of Britain and the Netherlands.
So, finally Microsoft kind of will have to offer updates for Windows XP for at least another year.
They also distribute updates for Windows XP Embedded (plus all ATMs in the world), it is another way of development for those same updates :)
-
Dear whom it may concern,
I saw one of the support forum of Blackberry Web site on "software update, not received the AT & T unlocked brand PRIVATE when you use a non - AT & T SIM card". How can I receive the OTA update in the notification bar?
Now, my OS is Mashmallow 6.01 build No.. AAF355 (June 1, 2016) or do I have to update (auto loadder) my Priv to AAG873 in order to get the direct OTA from Blackberry in the future.
Thank you
Good questions. I can speculate only at this stage. I guess that since it is updated by BB, they use a revision update for all devices to facilitate management. AT & T updates their different, since they have different methods of approval (Note T-mobile even updated as unlocked devices). Unless you want to get specific version of AT & T that could fix something that the other version does not work, I'd wait for the OTA. I did three refills of OS because I couldn't OTA of AT & T, and they take a lot of time. Take the time then to restore and to reconfigure all the settings you had before. Not funny.
To be more precise questions. Depends on you, but for me, would be updated via OTA only now that it's available. Yes, if you want auto charger, use AT & t. even as before, wait for OTA, unless you have a specific automotive need load the operating system.
-
EX 60 does not receive the CUCM phonebook directory
Cisco EX60 is registered on the CUCM, but it does not receive the phone book. IP phones receive the directory.
Cisco Services for user data is active and running.
CUCM system version: 9.1.1.20000 - 5
EX60 software version: TC6.3.1.f768649
You must mention the URL of the directory on your EX60 in order to extract the CUCM directory.
EX60 login go to Configuration > server directory > URL and mention of the URL in this format:
https://: 8443/cucm-uds/users First, you can test by opening this URL in a browser to verify if it is correct.
-
Hi, I bought acrobat adobe pro ms with order number: 12287735659 but I have not received the download link and the serial numbers of adobe and had this message there is a problem processing your order, please contact our Service team customer to 800 448 1642 for assistance. my credit card is already loaded, but not received numbers.please series suggest
Hi Kunal,
If the problem still persists, can you please contact the support for this issue through https://helpx.adobe.com/support.html#/top_products.
Please do not hesitate to me message in person if assistance is needed.
Concerning
Stéphane
-
I was paying to get Dreamweaver CC on March 14, 2016, and I was wrongly input from another Adobe account Cloud account.
I received the order of Confirmation e-mail the same day. Can I change the billing for my PC account again?
And yet, I have not received the final email to tell me Adobe accept payment in 72 hours.
Contact adobe during the time pst support by clicking here and, when available, click on "still need help," http://helpx.adobe.com/x-productkb/global/service-ccm.html
-
Hello 11/18/2015 I bought Illustrator photo and ask the Adobe site plan for individuals with credit cards, but to date I have not received the confirmation email. How can I contact for more information on the good end of the order?
Your subscription to cloud shows correctly on your account page?
If you have more than one email, you will be sure that you use the right Adobe ID?
https://www.adobe.com/account.html for subscriptions on your page from Adobe
.
If Yes
Some general information for a subscription of cloud
Cloud programs don't use serial... numbers you, connect you to your cloud account paying to download & install & activate... you may need to sign out of the cloud and restart your computer and log into the cloud for things to work
Sign out of your account of cloud... Restart your computer... Connect to your paid account of cloud
-Connect using http://helpx.adobe.com/x-productkb/policy-pricing/account-password-sign-faq.html
-http://helpx.adobe.com/creative-cloud/kb/sign-in-out-creative-cloud-desktop-app.html
-http://helpx.adobe.com/x-productkb/policy-pricing/activation-network-issues.html
-http://helpx.adobe.com/creative-suite/kb/trial--1-launch.html
-ID help https://helpx.adobe.com/contact.html?step=ZNA_id-signing_stillNeedHelp
-http://helpx.adobe.com/creative-cloud/kb/license-this-software.html
.
If no
This is an open forum, Adobe support... you need Adobe personnel to help
Adobe contact information - http://helpx.adobe.com/contact.html
Chat/phone: Mon - Fri 05:00-19:00 (US Pacific Time)<=== note="" days="" and="">===>
-Select your product and what you need help with
-Click on the blue box "still need help? Contact us. "
-
Cannot start Acrobat DC. Could not receive the confirmation e-mail. How can be changed the e-mail address?
Hello
The following link will guide you on how to change your email address associated with your Adobe ID
Change the e-mail address associated with Adobe ID.
Please follow the steps and let us know how it goes.
Concerning
Sukrit diallo
-
I bought the first cc, but I did not receive the activation code.
I bought the first cc, but I did not receive the activation code. Is there a place where I can look for?
There is no serial number for CC products. Sign in to your account on the website, download the Cloud creative application, install it and connect, then install the software.
Log, activation, or connection errors. CS5.5 and later versions
Mylenium
-
Printer HP B209a does not get the IP address of my router
Computer is a HP G71 running under Windows 7 64-bit
Router is a NETGEAR's WNR3500L with the latest firmware and a unique SSID
Using the latest version of the software install HP B209a
Towards the end of the installation for the wireless feature, the installation stops and tells me that my PC is on a network other than my printer. All wireless devices connected to my router have 10.0.0 # IP addresses. Through many installs the printers IP address is constantly as 192.168.0.109. The summary on the printer wireless shows my unique routers SSID but when I open my router software and devices attached, the printer is not listed. My router is attached to a simple DSL modem with no wireless features. I tried the following hotfixes recommended in these forums.
- Connect the printer to the router through WPS with push button. Connection is returned as a success, but identified printer router SSID as grabbled alphanumeric characters and not an IP address. Router does not show the printer in the devices. During the printing installation software PC and printer fail to communicate when the USB cable is connected.
- Connect the printer to the router through WPS with PIN. Connection is returned as a success, but all the information in the router has been changed and all other wireless devices disconnected. Connection to the router has shown the SSID THAT became grabbled of alphanumeric characters and the security key was changed. No wireless device was attached to the router, but the wired connections remain intact. Fixed key SSID and security. All other wireless devices back in place, printer does not have.
- Ping network devices. Ping 10.0.0.1 to 7 came back as successful. 192.168.1.109 ping failed.
- IP address of the printer has entered into a browser address bar. Returns a Google search page, but not for access to the network printer. Address of more than one entry address bar and couldn't connect to 10.0.0.1 (router) and 192.168.0.1 (DSL modem)
- Unplug the DSL modem router. All wireless devices to connect to the router but do not have access to the internet. During the installation of the printer software, when you are prompted to connect the USB to the PC, printer and PC fail to communicate.
- Turned off the Windows Firewall, both public and private without success
- Used the Hp network diagnostic utility and it does not can find printer.
I have installed and uninstalled the software several times. The printer has always identified my identifier SSID is correct and the network key. But during the finalization of installation I get the message and cannot connect PC printer because they are on different networks. I have no idea where the printer receives the IP address. It should be an address from the router, but it is not. IP address of the modem DSL IS in the format # 192.168.0, but given that the modem is the base model with the wireless or network capabilities, the printer cannot logically connect to it. I tried to unplug the router and the printer several times without success. The possibility of changing the IP of the printer through the browser is not possible for the reasons given in 4. What are the other options to change the IP address of the printer? If I can assign an address # 10.0.0, I think it will solve my problems.
Is your DSL modem is a modem/router combo (most are)? If so, it probably has a structure of 192.168.0.X and is probably a wired router (only).
This DSL modem/router is attached to the WAN, or one of the LAN ports on the back of the Netgear? Try to move to the other type of port, and then restart both routers.
On the front of the printer, click the settings 'Restore defaults' and wireless the wireless radio.
Finally, the Netgear settings, here are some tips:
1 make sure that DHCP is active, the SSID is not hidden and that MAC filtering is not enabled.
2. ensure that the 802.11 g mode (as well as other modes is very well).
3. use WPA or WPA encryption, not WEP (it is not secure and may cause connection problems)
4 change the channel of the Netgear to 11 (Yes, I know it makes no sense, but it works).
-
When I open a link in a new window does not display the web address.
When I open a link in a new window does not display the web address. What have I done wrong? It used to work and it works if I open the link in a new tab, the problem is that I hate to use tabs prefer a new window every time... Help!
Start Firefox in Firefox to solve the issues in Safe Mode to check if one of the extensions or if hardware acceleration is the cause of the problem (switch to the DEFAULT theme: Firefox (Tools) > Add-ons > appearance/themes).
- Makes no changes on the start safe mode window.
- https://support.Mozilla.org/KB/safe+mode
-
6248 VLAN do not receive the DHCP scope
I created two new DHCP scopes in my windows server 2003:
192.168.2.0 - public, and
192.168.3.0 - VOIP.This DHCP server is connected to a Dell powerconnect 2708, which is connected to our new powerconnect 6248P via fiber point-to-point.
In the new computers on network on the default 1 VLAN are correctly attributed IPs as they connect.
I issued the following commands to the 6248 CLI:
Enable
Configure
database of VLAN
VLAN 20
VLAN 30
outputConfigure
range of interface ethernet 1/1-g1/g2
switchport mode general
VLAN allowed switchport General add 20
switchport General pvid 20
l2relay DHCP
outputConfigure
range of interface ethernet 1/1-g3/g6
switchport mode general
VLAN allowed switchport General add 30
switchport General pvid 30
l2relay DHCP
outputinterface ethernet 1/g11
switchport mode general
VLAN allowed switchport General add 20
VLAN allowed switchport General add 30
l2relay DHCP
outputConfigure
interface vlan 20
name 'PUBLIC '.
Routing
IP 192.168.2.1 255.255.255.0
IP helper 192.168.1.150
outputConfigure
interface vlan 30
name "VOIP."
Routing
address 192.168.3.1 255.255.255
IP helper 192.168.1.150
outputIP routing
I also added all traffic on VLAN 20 and 30 of VLAN on ports 1/g11 (6248) and port 2 (2708). VLAN 1 access was removed from ports 1/1/g1-g6 (6248)
Everything seems to have been set correctly, but I can't get a response from the DHCP server on all ports attached to VLAN 20. The powerconnect 2708 switch is unable to pass the baton to the server? Is it possible that something falls in the point to point?
I would greatly appreciate any comments or suggestions, thanks!
The 6248 has no default gateway. It wont let me put 192.168.1.1 because he does not reside in the same subnet as the 6248 (192.168.99.1)
The 2708 has listed 192.168.1.1 as its default gateway.
At this point, the network has too many complexities for me to unravel. I am very happy that at least I solved for DHCP when we finally migrate our server to the new location.
Once the server is up, and the gateway/firewall are directly connected to the 6248; I will review the correct configuration of this network.
Some advice to those who might have a similar problem: check your management VLAN. It may not be the same VLAN 1 if you plan to routing to work from VLAN 1 to nowhere else because the VLAN management cannot be routed. Also check static routing of your access point, make sure the front door has a return of the ips of your VLAN, IE: 192.168.2.0 255.255.255.0 gateway_ip
That's all for now. Thank you to all who have contributed
-
Registration of client-sample-app Push received the error 403
Hi guys.
I work the pusk sdk demo. When I run the client Simulator demo.
first register the URL of content provider. I got a 200 response code. It is successfully
then register at https://pushapi.eval.blackberry.com. this time, I got a 403 responsecode
and the text of the response is
Http: 403 error,
"http://www.w3.org/TR/xhtml1/DTD/xhtml1-strict.dtd" > ""
http://www.w3.org/1999/xhtml"lang ="fr"XML: lang ="fr">
Access forbidden!
BPA registration rejectedWhat's wrong?
Note that I use mds to connect to the network
I don't know why I got a 403 forbidden response.
can I subscribe to http://pushapi.eval.blackberry.com with '; '. deviceside = false '?
or some settings wrong in my url?
Thank you. !
Unfortuantely, as far as I know, you can subscribe to the BPA server using the Simulator.
As long as these devices BES have BIS service book they should be able to receive push sent via BIS push server.
Maybe you are looking for
-
Someone CAN ME SAY what THE FILE '623fe9f43c1d431626c7e1. EXE IS?
I get a dialog box asking me to install this binary file when I open Firefox. The source location is long to give me the server source and I was wondering if this is a file for Firefox or a virus.
-
Can receive text messages, users of Android and not on others
Hi, I've looked everywhere and even phoned Apple customer service to try to solve this problem, but have failed. I can't receive SOME Android user texts but other ADCs. If it was all Android users it would be understandable, but just next to some rea
-
my printer has a paper jam which I cleared, but it still says paper jam
my printer has a paper jam which I cleared, but it still says paper jam and print
-
Mouse without borders lose laybout simetimes keyboard? How to prevent this?
Using the mouse without boundaries between my workstation (Windows 7 64) and my laptop (Windows XP). Sometimes I seem to lose the keyboard layout when moving to the computer remote (laptop). I still put on correct page if I use the local keypad but t
-
HP ENVY sleekbook 4-1025tx OVERHEATING!
my HP ENVY sleekbook 4-1025tx overheating when the laptop is connected to the charger it has reached temperature max 85 cel. the laptop starts to cool down as soon as I unplug the charger until it reaches 50 degrees Celsius. can someone guide me on w