Query before trigger problem

Similar Questions

• Possible to set up buffer - delay in the implementation of large number of buffers - IMAQ trigger problem

  Hi all

  I thought that I could transfer it here because it might be a more appropriate forum. I have a bit of time pressure, so I hope someone can help me. I'm having a problem with a program that I wrote to acquire and store images from a camera to linear scan.

  My camera (SUI Goodrich, 1024 pixels) is connected to a card framegrabber (PCIe-1427), which is connected via a RTSI cable to a PCI-6731 card attached to a SCC-68 (series) connector M.  My goal is to drive a mirror galvanometer scanning and acquire images from the camera continuously on each scan. As the galvo scan will be the frame of an image (1024 pixels x 1024 lines).

  I managed to do it (I think), as my direct purchase program works exactly as I expected. However, when I try to save the images, I noticed that for a larger number of images, the starting point of the image is shifted the same amount for each image. I'm not really sure what's going on, it seems to me that there is a delay in the use of the VI "IMAQ set up buffer" when a larger number of buffers is used, (or even 100). Is it possible that my hardware trigger does not wait for all buffers to be configured before you start to run?

  I would really appreciate any idea or ideas that anyone could have on this issue.

  Sincere greetings,

  Gill

  I fixed the problem by doing that I don't use actually 1000 stamps to save 1000 frames. Program works if the number of buffers is lowered.

• Jump to page before the problem

  Hello
  I have two queries and two layouts in my report. If both conditions are met, then run the two layouts. The second provision has a required Page Break before the value 'yes '. However if query number one conditions is not met I didn't need the page to break. I have a column (cs_count) cash report summary level "item" in a query. If only the points count = 0 then the 1st page does not work and the page break is not necessary.
  How can I set the condition to have a page break, if both queries executed but not so just the 2nd query runs?
  
  If cs_count = 0 then
  Before = No page break
  on the other
  Page break before = Yes
  end if;

  You could create a model framework that view you or hide depending on your condition uses a format trigger. Then set the avant-propriete to this new framework Page break.

• Prior insertion trigger problem

  Hi Guyz,
  
  I am facing a strange problem or may be wrong somewhere, but can't find my problem, I hope I'll get the solution to my problem here im im.
  
  IM updating my quantities in the table MN_ITEM_DETAILS.

  SQL> DESC MN_ITEM_DETAILS
   Name                                      Null?    Type
   ----------------------------------------- -------- ------------------
   SI_SHORT_CODE                                      NUMBER(10)
   SI_CODE                                            NUMBER(15)
   ITEM_DESCP                                         VARCHAR2(200)
   ITEM_U_M                                           VARCHAR2(6)
   ITEM_QTY                                           NUMBER(10)
   ITEM_REMARKS                                       VARCHAR2(100)

  I have below master-details on before insert trigger block works very well.

  SQL> DESC MN_MDV_MASTER
   Name                                      Null?    Type
   ----------------------------------------- -------- ----------------------------
   MDV_NO                                    NOT NULL NUMBER(15)
   MDV_DATE                                           DATE
   WHSE_LOC                                           VARCHAR2(15)
   PROJ_WHSE                                          VARCHAR2(30)
   ACTIVITY_LOC                                       VARCHAR2(30)
   MRF_NO                                             VARCHAR2(30)
   CLIENT                                             VARCHAR2(30)
   CLIENT_PO#                                         VARCHAR2(15)
   CLIENT_PO_DATE                                     DATE
   WHSE_INCHG                                         VARCHAR2(30)
   WHSE_DATE                                          DATE
   RECD_BY                                            VARCHAR2(30)
   INSPECTED_BY                                       VARCHAR2(30)
   DRIVER_NAME                                        VARCHAR2(30)
   REMARKS                                            VARCHAR2(200)
   RECD_BY_DATE                                       DATE
   INSPECTED_DATE                                     DATE
   DRIVER_NAME_DATE                                   DATE
   CST_CENTER                                         VARCHAR2(15)
  
  SQL> DESC MN_MDV_DETAILS
   Name                                      Null?    Type
   ----------------------------------------- -------- ----------------------------
   MDV_NO                                             NUMBER(15)
   ITEM_CODE                                          NUMBER(15)
   ITEM_DESCP                                         VARCHAR2(150)
   ITEM_U_M                                           VARCHAR2(6)
   ITEM_QTY                                           NUMBER(6)
   ITEM_BALANCE                                       NUMBER(10)
   PROJECT                                            VARCHAR2(15)
   ACTIVITY                                           VARCHAR2(15)
   LOCATION                                           VARCHAR2(15)

  All the triggers to INSERT before & after INSERTION block level

  PRE-INSERT -- ON details block level 
  UPDATE MN_ITEM_DETAILS
  SET ITEM_QTY = NVL(ITEM_QTY,0) - NVL(:MN_MDV_DETAILS.ITEM_QTY,0)
  WHERE SI_CODE = :MN_MDV_DETAILS.ITEM_CODE;
  
  POST-INSERT MASTER BLOCK LEVEL TRIGGER
  INSERT INTO MN_MRBV_MASTER(
  MDV#        ,
  MDV_DATE      , 
  WHSE_LOC      , 
  CST_CENTER    )VALUES
  (:MN_MDV_MASTER.MDV_NO         ,        
  :MN_MDV_MASTER.MDV_DATE       ,        
  :MN_MDV_MASTER.WHSE_LOC       ,        
  :MN_MDV_MASTER.CST_CENTER); 
  
  POST-INSERT ON DETAILS BLOCK LEVEL
  INSERT INTO MN_MRBV_DETAILS(
  MDV#         ,
  ITEM_CODE     , 
  ITEM_DESCP    , 
  ITEM_U_M           , 
  QTY      , 
  ITEM_BALANCE  ,
  PROJECT       , 
  ACTIVITY      , 
  LOCATION      )VALUES
  (:MN_MDV_DETAILS.MDV_NO         ,
  :MN_MDV_DETAILS.ITEM_CODE     , 
  :MN_MDV_DETAILS.ITEM_DESCP     ,
  :MN_MDV_DETAILS.ITEM_U_M       ,
  :MN_MDV_DETAILS.ITEM_QTY       ,
  :MN_MDV_DETAILS.ITEM_BALANCE,
  :MN_MDV_DETAILS.PROJECT      ,  
  :MN_MDV_DETAILS.ACTIVITY      , 
  :MN_MDV_DETAILS.LOCATION       ); 

  until the above works fine and its update of the MN_ITEM_DETAILS. ITEM_QTY correctly
  
  but im using the same as above in the MASTER-DETAIL table below but do not update the ITEM_QTY in MN_ITEM_DETAILS
  

  SQL> DESC MN_MRBV_MASTER
   Name                                      Null?    Type
   ----------------------------------------- -------- ----------------------------
   MDV#                                      NOT NULL NUMBER(15)
   MDV_DATE                                           DATE
   WHSE_LOC                                           VARCHAR2(15)
   RET_FRM_PROJECT                                    VARCHAR2(1)
   RET_FRM_CLIENT                                     VARCHAR2(1)
   CST_CENTER                                         VARCHAR2(15)
   WHSE_INCHG                                         VARCHAR2(30)
   WHSE_DATE                                          DATE
   RETURN_BY                                          VARCHAR2(30)
   INSPECTED_BY                                       VARCHAR2(30)
   RETURN_BY_DATE                                     DATE
   INSPECTED_BY_DATE                                  DATE
   DRIVER_NAME                                        VARCHAR2(30)
   DRIVER_DATE                                        DATE
   REMARKS                                            VARCHAR2(250)
  
  SQL> DESC MN_MRBV_DETAILS
   Name                                      Null?    Type
   ----------------------------------------- -------- ----------------------------
   MDV#                                               NUMBER(15)
   ITEM_CODE                                          NUMBER(15)
   ITEM_DESCP                                         VARCHAR2(150)
   ITEM_U_M                                           VARCHAR2(6)
   QTY                                                NUMBER(6)
   ITEM_BALANCE                                       NUMBER(10)
   PROJECT                                            VARCHAR2(15)
   ACTIVITY                                           VARCHAR2(15)
   LOCATION                                           VARCHAR2(15)

  PRE-INSERT--> here its not updating the MN_ITEM_DETAILS.ITEM_QTY table any sugesstion plz why its not updating...?
  MDV_DETAILS
  UPDATE MN_ITEM_DETAILS
  SET ITEM_QTY = NVL(ITEM_QTY,0) + NVL(:MN_MRBV_DETAILS.QTY,0)
  WHERE SI_CODE = :MN_MRBV_DETAILS.ITEM_CODE;

  Concerning
  
  Houda
  
  Published by: houda Shareef on January 8, 2011 02:19

  try to write your code in before update trigger

• before trigger

  I am trying to eliminate the data of 'delay' before an arbitrary trigger event (only on the graph, but if the file should be truncated so be!) and I don't have a chance.  Please see the chart below for reference.

  Any help will be appreciated.

  

  Use a trigger Combi with the defined pre and view the settings of the trigger and then use it to control a relay module where to send you the rest data through. The relay will get out data even if the trigger is active (high) and not when it is off (bass).

  You can write the data before the relay to write all data, or after the relay to the only desired writing triggered zone.

  

• Trigger problem

  I need to trigger PFI0 in labview at a specific time (every hour). The signal is available for collection in the hh:55:01 - hh:59:59. I have made several attempts, but failed each time. Please see the written description vi in, maybe you can help me.

  I hope I understand your problem.  You can try something like the joint.  Drop 2 Untitled in the attached schema. The second trigger VI has included (without the Subvi) time control.

• Pre trigger problems

  Hello

  I'm having some trouble with my project. I can't understand what is wrong. The project involves building a FPGA target that uses a trigger to start sampling data and must also have pre/post trigger functions, but it does not fire when it is supposed to.

  I enclose my program.

  Kind regards

  Tim Jansson

  (It seems that I managed to double post this thread again. I apologize and I hope that it will not cause too many problems)

  Never mind! I solved it!

• before trigger with four cards PXI-6115

  Hello

  I have a PXI-1010 chassis with four cards PXI-6115, labeled boards 3, 4, 5, 6, installed in it.  Each of these cards has 4 analog inputs (BNC inputs).  In my current system, all four boards fire off the coast of the entrance on first 3 analog.  I'm using an analog trigger mounted on Board 3, which then triggers a trigger digital beginning on the boards, 4, 5 and 6.

  Now, I would be able to take samples before firing.  I worked on this for a while and that seems to happen is that 3rd Chess Board properly triggers and takes samples of relaxation before, but plates 4, 5 and 6 are somehow trigger too late or early or something - they never record my test signal input of.

  Can someone help me understand where I'm going wrong here?  I enclose my VI and also a picture of the important part of my block diagram.

  Thank you!

  It could be that you connect the number of samples per channel in the clocks of the sample for tables 4, 5 and 6. This will ensure that the task creates a buffer on your PC that is large enough to accommodate all the samples you want to read.

  Also, why did you remove the structure of sequence? You need to ensure that the advice of slaves were armed in front of the master bedroom.

  Here is a link to an example similar to what you're trying to do. This example acquires the data at different speeds on different boards, but it seems that everything is identical to what you are doing. I think it might be useful for you: https://decibel.ni.com/content/docs/DOC-11698

  Jeremy P.

• ASA Windows7 and startup-before-logon problems (SBL)

  We try in vain to get Windows7 SBL working with configuration following (SBL works for XP);

  ASA5520

  ASA 8.0 (4)

  ASDM 6.1 (5)

  AnyConnect 2.4.1012

  VPN Plus license (SSL VPN peers 100)

  When you configure the group policy for Clent download optional Module we have option for vpngina and can not see module start before logon (EPP), in paragraph 2.4 of the AnyConnect Client documentation.

  Is this a problem of license type or do we need an ASA/ASDM software update?

  Thanks in advance for your help.

  The following doc can be referenced on the rest of the SBL configuration:

  http://www.Cisco.com/en/us/products/ps6120/products_configuration_example09186a00809f0d75.shtml

• after insert trigger problem

  I am trying to write a trigger that will update a neck date after each insertion.
  
  CREATE OR REPLACE TRIGGER PS1. XX_CDATE
  AFTER INSERT ON ps1.COMMNPLANBUDGET
  Old SEO AS OLD AS new NEW
  FOR EACH LINE
  declare the PRAGMA AUTONOMOUS_TRANSACTION;
  BEGIN
  Update ps1.COMMNPLANBUDGET set CREATION_DATE = sysdate where PROJECTID =: new. PROJECTID;
  commit;
  END XX_CDATE;
  
  For the same thing, I wrote the code above, it created successfully but when I am inserting a record pass date is not updated. Please let me know where I did wrong. Thanks in advance

  It's everything you want

  create or replace trigger ps1.xx_cdate before insert on ps1.commnplanbudget referencing old as old new as new for each row
  begin
       :new.creation_date := sysdate;
  end xx_cdate;
  

  Use a trigger to insert BEFORE and just change the: NEW value

• remove the trigger problem

  Hi I am trying to create a trigger (I'm relatively new to Oracle) to stop the events are removed if the date is earlier than the current date. This is the SQL syntax for my table
  
  CREATE TABLE event
  (the numeric (5) to event_id not null,)
  concert_id numeric (5) not null,
  date EVENT_DATE,
  );
  
  
  
  What I've tried so far is:
  
  CREATE OR REPLACE TRIGGER event_deleting
  BEFORE the DELETE event
  FOR EACH LINE
  BEGIN
  IF REMOVE THEN
  SELECT e.event_date
  E EVENT
  WHERE e.event_id =: new.event_id;
  END IF;
  IF e.event_date < = SYSDATE
  THEN
  RAISE_APPLICATION_ERROR ("-20100, ' event cannot be removed");
  END IF;
  END;
  
  
  
  It gives me a few caveats, the first is that a DECLARE is missing and the second is an INTO is missing. Could someone kindly help out?

  What is

  CREATE OR REPLACE TRIGGER event_deleting
  BEFORE DELETE ON event
  FOR EACH row
  BEGIN
     if :old.event_date <= sysdate
     then
        raise_application_error (-20000, 'Event can not be deleted');
     end if;
  END;
  

• Satellite Pro M70 - connection network wireless & query Update Driver problem

  I have a portable Satellite Pro M70 under Win XP SP3 and would be very happy of little help and answers to the following problems:

  1 Wireles Internet connection problem: my laptop Satellite Pro M70-220 (part number: PSM75E-00D008G3) is an adapter Intel(r) PRO/Wireless 2200BG Network Connection, with driver version 9.0.2.25, according to Device Manager

  I am staying with someone, and I'm trying to use his internet connection through its network (WPA2) secure wireless home.
  I could connect my laptop to the wireless network, but I can not get Internet Explorer and Outlook Express to work on it.
  I tried the Intel Wireless driver update to the latest version of the driver 9.0.4.39, but got the same result, and I'm back to Driver version 9.0.2.25.

  If you'd be grateful if someone could advise me on what could cause this problem and how to solve it.

  2. wireless driver update: site Web de Toshiba advised me for the two years that there is a driver update available (Atheros Wireless Driver v 7.7.0.406.2) for my laptop, but I have NOT installed, because the wireless network adapter Intel(r) PRO/Wireless 2200BG, NOT of Atheros.

  Ques:am I correct?

  Question: Why the Web from Toshiba site recommends the Atheros wireless driver update?

  Thank you

  AlanCB

  Hi Alan

  1.
  Can you use IE and other applications if the WIFI network is not secure with WPA2?
  You can test using WEP?
  Just to be safe because of securing WLAN.

  2.
  You are right. Your model has Intel WLAN card and if you need a new driver just visit Portal Toshiba WLAn under http://aps2.toshiba-tro.de/wlan/

  I really don't know what service or upgrade of system you are using, but if everything works well you don't need any update to date.

• No sound on the awakening of the day before, screen problems

  When I wake up my laptop in standby or hibernation, I have no sound. When I check the Device Manager it is there no audio device detected. When I wake up, the screen has a bunch of white lines on it for a while, that finally clears. Both of these problems appeared at the same time a month ago. I don't know if this has to do with an update that I had some time, some kind of virus, or something else. AVG detects no virus. When I restart, all right. I'm running Windows 7 on a Toshiba Satellite A215-S4697 with plant material (except the RAM, I've updated).

  Have you visited site Tosh, specific to your model, and check updates of pilot?

• trigger problems

  I have a table name test.
  
  I want to write trigger1 and trigger2 for before the event of the insert on the test table.
  
  is it possible to write two or more triggers for the event itself.
  
  triggers how we write on a table.is it no limit on the number of triggers on a table

  user10447332 wrote:
  I have a table name test.

  I want to write trigger1 and trigger2 for before the event of the insert on the test table.

  is it possible to write two or more triggers for the event itself.

  Yes. Although I would never do it. Just to combine the two into one, as it you also control the order in which the code is triggered.

  >

  triggers how we write on a table.is it no limit on the number of triggers on a table

  I'm not aware of any documented maximum. But even once you don't want that, because triggers will fire in a random order. Unless you're on 11G, where you can control the order in which they are raised (by using the FOLLOWING clause).

• Problem creating motion tweens; not before no problem.

  The last time I opened Flash, my method of creating motion tweens works beautifully. Create the first keyframe with work on it, pushing some middle managers, create a new image key at the end of it, then move/modify the work in this keyframe. Select all, right click, motion tween. Worked.

  Now when I try to create a motion tween to make an object move/etc, it just does not work. Instead of the arrow, I get the area between filled with blue, and he jumps right in position in the last picture.

  The kicker is that the classic tweens are still working! But I don't want to use Classic tweens.

  What could have changed since the last time I created an animation? What I am doing wrong? I am so frustrated, I tried to figure out the problem on my own for about an hour now.

  If you wait the arrow, you are probably thinking of the classic tweens.