Question about hot spots

Similar Questions

• Question about hot pluggable memory

  Recently, I want to increase the memory of the virtual machine online. How can I check if I have this feature on my product? I could see the function of licensing information.

  Memory Hot - Add requires hardware VM worm. 7, and you must activate add Hot for this virtual machine in the settings.

  Remember that add Hot will not work on Win 2003 standard, you need, Enterprise, DataCenter, or Web Edition.

  ---

  VMware vExpert 2009

  http://blog.vadmin.ru

• A question about 'value spots' in the Vision Assistant of NOR

  Hello, all,.

  I am a new learner or vision.

  When I use 'mark set' in the Vision Assistant of NOR. It works well. for example

  

  (The image above is the example in the Vision Assistant of NOR, please see help > Assistant Solution > Inspection of dental floss)

  However, when I put the program NI Vision Assistant to create a Labview VI program. (Tools > create a LabVIEW VI), then run the VI, it no longer works.

  

  The result of the system of coordinates outside is always like that.

  

  I can't find where is the error. I tried a few other examples in the Vision Assistant of NOR. If the command "set mark" is used in the program in the Vision Assistant of NOR. then create the LabVIEW VI.

  The problem still occurs.

  I hope some man experienced in NI Vision could help me.

  Thank you.

  Hi all

  This problem has been reported under Corrective Action Request (CAR) 441410 and has since been fixed in 2014 of VDM. I highly recommend upgrading to the latest version here: www.ni.com/download/vision-development-module-2014-f1/4971/en/ because it contains other patches. If you are unable to do so, I have attached the patched file, you need to change. Replace the following file (assuming that the default installation location): \National Instruments\LabVIEW 2013\vi.lib\vision\Vision Utils.llb Assistant with the version I have attached here, and that should solve the problem you see with NaN values of reference in the VG of the generated code.

  Kind regards

  Joseph

• Hot Spot question slide

  I use 9 Captivate and my hot spot question has two hot spots: Yes or no. How can I make sure the user, just click either Yes or no, not both. It defeats the purpose of the question when there are animations that are glued on the two hot spots, and you cannot remove them.

  Please help :)

  You will need a question slide custom hotspot, not the default value that is too limited. I never use it myself. There is not really your use case described in this article, but it can offer you a few ideas anyway:

  Hotspot issues in Captivate 8 - Captivate blog

• Hot spot question type

  Just out of curiosity, does anyone know why hot spot issues are limited to 10 hot spots? Maybe we need a feature request to remove the limit?

  Why not to create a personalized question, using transparent forms (can have any shape, unlike the traditional hotspots)? You can have as much as you want.

• Hot spot quiz questions keep coming back to point original hot location.

  Hello. I develop a course Adobe Presenter 8 which contains a certain point hot quizzes with many options for users to click (we do not have time or money to do the simulation so it was the "fix").

  Whenever I have to 'Manage the Quiz' is editing the manifest, or a quiz etc, it resets my reactive quiz at the original location inserted Adobe. I've been making small to contain a detailed image and duty resize several hot spots over and over again is frustruating.

  If anyone else has encountered this before? And if so, how you solved this problem?

  Thank you very much!

  I do have trouble-shooted finally my problem! Some of the questions hot spot missing identifiers 'Hot Spot 1' so to speak and those who have been those who have been reset. I named each hotspot again and now this problem has been resolved.

  Thank you!

• Creating a hot spot question

  I am wanting to create a hot spot question. I have an image that I created for this question. I've identified "hot spots" on the image and when I preview the issue, hot spots are already identified before the user clicks top. I will use this issue to test the attention of person with ability to detail. Any ideas on how to solve this problem?

  

  Erik, it is a matter of default access point, the hot spots have a default setting with a stroke of 1 p in blue. You must make this race 0 for width make the invisible race.

  Select the hot spot, open the properties panel and set the width of the stroke to 0. If you wish for all the hot spots, you can save the style as default style, using the diskette icon just beneat Style (second icon from the left)

  

• Is there a limit on the number of hot spots, that we can include on a screen?

  Is there a limit on the number of hot spots, that we can include on a screen? I'm putting in about 25, but it is defaulted to 10?

  Hot point quiz questions are indeed limited in the number, you can have on a slide.

  When it comes to normal blades, using ordinary boxes by clicking, you could easily have 25 or more, but then your score will be much more complex and it will not be a true quiz question.  Each separate click box can be set up to score separately.

• Hot spots

  I tried to figure out how to hotspots and I even looked in the field help in the program and sought here on the forums and I couldn't find it myself how to create hot spots. If someone could just point me in the right direction, where the tool is that I can mess around with it, myself I hope to learn to use it and have more specific questions about it if I need it.

  Search F1 help on the hotspot of Word.

  Select the image and look in the lower left corner of the extended properties
  Inspector for hotspot tools.

  Note: you cannot apply links hotspot of background images.

  --
  Alan
  Adobe Community Expert, dreamweaver

  http://www.Adobe.com/communities/experts/

• Satellite L650-11R - a few questions about this

  Hello there :-)

  I have a few questions about my new L650.

  I've never had Toshiba notebook before so I apologize if some of these "quirks" are actually quite normal on this laptop. I really want to hear the views of other users L650.

  1)
  First of all, by the time I turned it on I saw gradient thin (1-2 mm) along the right edge of the screen that goes from the bottom up. Maybe "degraded" isn't the right word, but it seems that since two or three pixels are kind of discoloration or lose brightness/sharpness to the edge along the straight bezel. It is not really that visible, looks like the colors are desaturated a bit here or brightness is a bit lacking. He can be seen everywhere (bios or no color in Windows, but better in the lighter background).
  The left side (or other) seems ok, all this along the right edge is somewhat suspicious. If one can compare? I don't know if it's something to worry about or is just supposed to be like that.

  2)
  The other thing I noticed heating of the processor (Intel i3 330M) and GPU (ATi Mobility Radeon 5650). It's pretty hot here right now (I would say that the temperature is around 28 degrees Celsius when using cell phones). He is sitting on the hard surface (table) and nothing is blocking the vents.
  However, at "rest" (surf the web & regular light stuff), average CPU temp hovers around 58 ° C. It usually goes from 45 to 62 in just a few minutes after starting, and then I can hear and see (Toshiba PC Health Monitor) evacuate the kicks in. Temp goes back to 50 +, event stops and then the temp rises to 60 + until the vent is used again.
  During load full (Prime95 or some games), CPU is going all the way up to 75 degrees (the highest being 77). Fan runs at 75 to 77% during this time, never go faster.

  GPU idling is usually around 5 degrees above temp CPU (62-65). During full load (for example. Benchmark of Far Cry 2), I see a lot of stuttering with the latest drivers Catalyst and DX10 (not sure if the stuttering has something to do with heat), otherwise it is ok (no artifacts or anything like that). Temp of GPU during the loading goes up to 74-75, fan speed is locked at 30%, the frequency of the heart 5650 is 450 MHz. left side of the laptop (vent and below) is pretty hot, while the keyboard is warm (or slightly warmer who who).

  These time seems correct and safe in the long term? I'd rather events works all the time (they aren't really very strong) and keeping time less than 50, but there are just wishful pious bios control events and I can't control not the bios. :-)

  3)
  This is just General related products. :-)
  Official specifications of Toshiba L650 say ATi 5650 (between other low range GPU), but I saw a few specifications calling for there 5730 (same model 11R). Is there really a Satellite L650 with ATi 5730 GPU models?

  Sorry for the long post, I tried to include the best possible description that I could do. :-)

  Thank you in advance.

  Thanks for the additional info!

• Satellite A350D - 20K - Question about upgrade second HDD + Temperature

  I have a question about my laptop. I have notticed it is a second location of HARD disk on the bottom.
  Is it possible to use this to increase my storage?
  And if yes, how do I do that? I don't see all the connectors.
  What type of HARD drive to use in case it is possible to use this slot machine?

  My second question is on my laptop to be very hot after a short period of use.
  I installed speedfan to record the temperature. When I start the laptop, it already is between 45 and 50 degrees.
  He stayed there for half an hour and then it starts to get warmer. When I start to use the laptop for anything, it triggers to between 70 and 80 degrees.

  This does not seem normal to me. I tried to clean the vents with compressed air, but it has not made a difference.
  I searched on the internet how to take the laptop part for proparly cleaned TI.
  But I can't so I'm looking that destroy it.

  This could be the cause and more importantly, how can I solve this problem?

  Tom

  The second HARD drive bay contains the HARD drive connectors?
  If Yes, then you can use a SATA 2.5 HARD.
  If there are no connectors, then you will not be able to use the second HARD drive

  > I have installed speedfan to record the temperature. When I start the laptop, it already is between 45 and 50 degrees. He stayed there for half an hour and then it starts to get warmer. When I start to use the laptop for anything, it triggers to between 70 and 80 degrees.

  CPU and GPU produce a lot of heat. The heat dissipation is always created then there s nothing unusual that the temperature rose to higher level.
  You can change the settings in Win 7 power management. You can set the CPU to lower performance and can increase the activity of fan, which will help lower the temperature.

• Certificate for the hot spot ISE error

  We have just install an ISE Server (Version 1.3.0.876) and that you have set up a hot spot for guest users portal. Everything on the Portal works fine, however! The question that we run is, we installed a public cert signed by a public CA (Starfield CA), but when you can go to the EULA page on the ISE server, they get an error the path of certificate cert becomes not filled. I watch the cert that it gets, and the path contains only the issued cert, not the case there are on it. (I think that cert requests the browser to go to a site to download the latest public certification for the issued cert)

  I can work around this in order to allow this IP address he strikes in the ACL on the WLC, but I would simply like to have deliver ISE cert WITH public cases that's just in case the IP changes, or it is actually hitting a VIP and it comes to be responsive would be.

  Does anyone know how this is done?

  I tried the following:

  From the cert out of ISE, added public certification in the server certificate and added to the ISE, no luck. (I can this is done properly, let me know if this should have worked)

  Added the case public in ISE and self-confidence, no luck with either.

  Let me know! Thank you guys!

  Good job to fix the problem and for taking the time to post back here! (+ 5 from me).

  What is interesting is that the ISE should warn you and automatically restart the server when a new HTTPs certificate is installed. I wonder if this behavior may be changed with the last patch/version. In both cases, glad your problem is solved!

  Now, you must mark the thread as "answered" :)

• A few questions about the colors of Patone

  I have a few questions about patone color since it is the first time that I use. I want to use them to create a paper letterhead and business cards in two colors.

  1)

  I don't understand that no sex is more than coated patone washed out colors. I heard that it's because the way paper absorbs the inkt. That is why the same results inkt in different colors on different papers (right?). My question is why is the patone black no sex so different than black normal (c = 0 m = 0 y = 0, k = 100) or black intense:

  

  When I print a normal document with cmyk, I can get pretty dark black color. How is it that I can't have this dark with patone color black color? Even text documents printed on a cheap printer can get a darker color than the color of Patone. He looks way too grey for me.

  (2) a first model, I want to print of patone in CMYK color (since I have like 10 different colors on a page of quick comparison). I know these CMYK colors distinguish the colors of patone and I can't get a representation of 100%. But is there a way to convert patone CMYK values?

  I hope some of you can help me with my questions.

  Thank you.

  You can get shades CMYK Pantone in Illustrator, (Swatches Panel > Open Swatch Library > color books > + PANTONE Color Bridge Coated or lying) but in my opinion, what's the point?  If you print to a digital printer, just use RGB (HSB) or CMYK. Personally, I never use CMYK called "equivalents." from Pantone

  Pantone colors are all mixed pigmented inks, which are fluorescent beyond the limits of the range of RGB and CMYK in particular. The original Pantone Matching System (PMS) was created for the printing industry. He described formulations of ink pigmented for each of its colors.

  Most digital printers (laser or inkjet) use CMYK. The range of CMYK is MUCH SMALLER than many mixed inks, printed on papers either paved or unpaved can deliver. When you specify no sex Pantone ink in artificial intelligence, according to Pantone conversion tables, HAVE "about" what will look like this color on a sheet no bed, try using CMYK. -In my opinion, this has little relevance to the real world conditions and should be avoided in most situations.

  If your project must be printed on a press printing with Pantone inks spots, then by all means, use Pantone colors. But don't trust the colors of the screen; rather get a Pantone swatch book and watch real inks on paper lying and uncoated, depending on the stock you will use on the press.

  With printing decreases rapidly for inkjet and web printers, Pantone has attempted to expand its relevance beyond the traction-date of publication (in the books and software alliances, with one such as Adobe) his old PMS inks and their supposed equivalent LAB and CMYK. I say "supposed" because even once, monitors RGB and CMYK inks can never be literally equivalent to many Pantone inks. But if you go to your project on a printing press printing, Pantone inks are still very relevant as of the "tones".

  I also put my preferences I > appearance of black both display all blacks accurately and output all blacks accurately. The only exception to this may be when you print on a digital printer, where there should be no problem checking.

  Rich black in artificial intelligence is a phenomenon of the screen, at least in the Prefs > appearance of Black, you specify also "out all inks like Rich Black"-something I'd do it EVER do so out for a real printing press. Still, I put my black people in artificial intelligence at the "output All Blacks Acurately" during a press release. If you fail to do so, then the press you will see any minor issue registration, with C, M and look at the back, especially around black characters.  UGH!

  Good luck!  :+)

• Two clicks to Trigger hot spot

  I noticed on my pieces of 6.5 recent AW I have to double-click on a hotspot on my home page to go to the next page, but if I go to an HTML page, from the AAM file does not display this behavior. Click on the first, the page moves slightly upwards and on the second click happens on next page.
  
  I don't remember what is happening before and I'm sure I started with a HTML page before. What can happen?

  > I saw on my pieces of 6.5 recent AW I have to click a hot spot on
  > my
  > home page twice to go to the next page, but only if I'm going to go to
  > a
  > HTML page, from the AAM file does not display this behavior. On the
  > first
  > click, the page moves slightly upwards and on the second click, it moves to the
  > next
  > page.
  >
  > I don't remember happening before and I'm sure I started with
  > a
  > Before HTML page. What can happen?
  >

  This is a new behavior in Internet Explorer - well, for several months now.
  When you launch the AW file, look at the text just below the IE toolbar,.
  He'll tell you some more about what is happening.

  You can work around this by integrating your AW (or Flash or another ActiveX)
  a function JavaScript such as documented on Adobe.com and elsewhere.

  Steve

  --
  Adobe Community Expert: Devices, Mobile Flash and Authorware
  My blog - http://stevehoward.blogspot.com/
  Authorware tips - http://www.tomorrows-key.com

• Hot spots that actually work?

  I am frustrated beyond here. I tried to get a hotspot question slide to work for more than an hour now. (Can you say, "Loss of productivity"?) Tried everything logic. Made of the hot spot larger, smaller, deleted the slide and recreated, disabled compression project, added/subtracted other hot spots, checked my hotspot is marked as the hot spot 'Correct', enabled the "show in the pointer", added images different and tried fused/not fused with background and other things I don't know I don't forget. Help! I need to work for my small business. It's something simple I forget here? Or they simply do not work?

  Received a response from my Bug report:

  Hi Brian

  It is a known with Captivate 3 bug seen with Fp 10. Please note that this works if you preview in the browser and also view the published content. The solution is to roll back to Fp 9.

  Sorry for the inconvenience caused

  Thank you

  -Suresh