Question of AnyConnect with Cisco ASA 5505
I keep hitting my head against the wall on this one. Whenever I try to connect to the AnyConnect SSL VPN I get the following error
"No address available for an SVC connection.
Up and down, I checked that my VPN pool be present and assigned. I have removed/re-added it so many times. I use the SMDA to implement through the wizard. Any help please?
Here is my config
It seems that you are falling into default group policy. You must activate the tunnel-group-list under the webvpn that allows users to select the group to which they connect, or set the attributes of the user to force the user into the correct connection profile...
activation of tunnel-group-list
WebVPN
tunnel-group-list activate
Configuration of the user attributes:
Chris mXB.dKavHoEa0gaC of encrypted password username
username Chris attributes
VPN-group-policy HBNS_AnyConnect
value of group-lock HBNS_AnyConnect
type of remote access service
--
Please do not forget to choose a good response and the rate
Tags: Cisco Security
Similar Questions
-
VLANS with Cisco ASA 5505 and non-Cisco switch
I have an ASA5505 and a switch Netgear GSM7224 L2 that I try to use together. I can't grasp how VLANs (or at least how they should be put in place). When configuring my VLAN on the ASA5505 it seems simple enough, but then on my switch, I thought I'd create just the same VLAN numbers that I used on the SAA and then add the ports that I wanted to use for each VLAN.
Currently on my ASA, I have the following VLAN configured...
outside - vlan11 - Port 0/0
inside - vlan1 - Port 0/1
dmz_ftp - vlan21 - Port 0/2
Port of Corp - vlan31 - 0/3
I need to do the same thing on my switch as well... On my way, I'm a little confused as to how I need to configure the VLAN. Below is the screenshot of web GUI...
Note: Normally you can now change the VLAN ID (red), but in this case the default vlan (vlan id 1) may not be changed or deleted, you can does not change its settings.
Tagged (green), Untagged (purple) and Autodetect (yellow) you must select at least 1. I'm not sure how to in one place to tell my inner vlan (vlan1).
I want VLAN1 ports 1-8 on my Netgear switch used alone to talk to interface/0/1 on the ASA5505 port. I don't want to NOT port 9-24 able to talk to ports 1-8 on the Netgear switch ports OR 0/0, 0/2 - 0 / 7 on the Cisco ASA 5505.
So, how can I configure my inner Vlan1 on ports 1-8 on the switch? Do mark, UNTAG, autodetect them? What about tours? I've been a bit the impression that I would set up my VLAN on both devices, then trunk port 1 and dedicate this port on both devices to nothing other than the sheath and the security of vlan would then take the packages where they need to go. Is this the wrong logic?
Hi Arvo,
If the port of the ASA is just part of a single VLAN (i.e. e0/0 single door 11 VLAN), this is called an access port. If the port of the ASA had to carry several VLANs, it would constitute a Trunk port.
To access ports (VLAN unique), you must set the switch corresponding to be unidentified for port this VLAN individual. If you decide to configure a trunk port, then the port of the switch must be set for labelling for each of VLAN who win the trunk.
For example, ASA I have:
interface Ethernet0/1
switchport access vlan 20
!
interface Vlan20
nameif inside
security-level 100
ip address 192.168.100.254 255.255.255.0
With the above configuration, the configuration of the switch would look like this (assuming the e0/1 port of the SAA is connected to 0/1 on the switch):
VLAN 20 - 0/1 = untagged
If instead you use a trunk port, the config would look like this:
interface Ethernet0/0
switchport trunk allowed vlan 10,20
switchport mode trunk
!
interface Vlan10
nameif outside
security-level 0
ip address dhcp setroute
!
interface Vlan20
nameif inside
security-level 100
ip address 192.168.100.254 255.255.255.0
Assuming that the ASA e0/0 port is connected to 0/1 on the switch):
VLAN 10 - 0/1 = tagged
VLAN 20 - 0/1 = tagged
Hope that helps.
-Mike
-
Cisco ASA 5505 VPN Site to Site
Hi all
First post on the forums. I have worked with Cisco ASA 5505 for a few months and I recently bought a 2nd ASA to implement tunnel VPN Site to Site. It seems so simple in the number of videos watched on the internet. But when I did he surprise it did work for me... I've removed the tunnels, a number of times and tried to recreate. I use the VPN Wizard in the SMA to create the tunnel. Both the asa 5505 of are and have the same firmware even etc..
I'd appreciate any help that can be directed to this problem please. Slowly losing my mind
Please see details below:
Two ADMS are 7.1
IOS
ASA 1
Nadia
:
ASA Version 9.0 (1)
!
hostname PAYBACK
activate the encrypted password of HSMurh79NVmatjY0
volatile xlate deny tcp any4 any4
volatile xlate deny tcp any4 any6
volatile xlate deny tcp any6 any4
volatile xlate deny tcp any6 any6
volatile xlate deny udp any4 any4 eq field
volatile xlate deny udp any4 any6 eq field
volatile xlate deny udp any6 any4 eq field
volatile xlate deny udp any6 any6 eq field
2KFQnbNIdI.2KYOU encrypted passwd
names of
local pool VPN1 192.168.50.1 - 192.168.50.254 255.255.255.0 IP mask
!
interface Ethernet0/0
switchport access vlan 2
Speed 100
full duplex
!
interface Ethernet0/1
link Trunk Description of SW1
switchport trunk allowed vlan 1,10,20,30,40
switchport trunk vlan 1 native
switchport mode trunk
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
interface Vlan1
No nameif
no level of security
no ip address
!
interface Vlan2
nameif outside
security-level 0
IP 92.51.193.158 255.255.255.252
!
interface Vlan10
nameif inside
security-level 100
IP 192.168.10.1 255.255.255.0
!
interface Vlan20
nameif servers
security-level 100
address 192.168.20.1 255.255.255.0
!
Vlan30 interface
nameif printers
security-level 100
192.168.30.1 IP address 255.255.255.0
!
interface Vlan40
nameif wireless
security-level 100
192.168.40.1 IP address 255.255.255.0
!
connection line banner welcome to the Payback loyalty systems
boot system Disk0: / asa901 - k8.bin
passive FTP mode
summer time clock GMT/IDT recurring last Sun Mar 01:00 last Sun Oct 02:00
DNS domain-lookup outside
DNS lookup field inside
domain-lookup DNS servers
DNS lookup domain printers
DNS domain-lookup wireless
DNS server-group DefaultDNS
Server name 83.147.160.2
Server name 83.147.160.130
permit same-security-traffic inter-interface
network obj_any object
subnet 0.0.0.0 0.0.0.0
ftp_server network object
network of the Internal_Report_Server object
Home 192.168.20.21
Description address internal automated report server
network of the Report_Server object
Home 89.234.126.9
Description of server automated reports
service object RDP
service destination tcp 3389 eq
Description RDP to the server
network of the Host_QA_Server object
Home 89.234.126.10
Description QA host external address
network of the Internal_Host_QA object
Home 192.168.20.22
host of computer virtual Description for QA
network of the Internal_QA_Web_Server object
Home 192.168.20.23
Description Web Server in the QA environment
network of the Web_Server_QA_VM object
Home 89.234.126.11
Server Web Description in the QA environment
service object SQL_Server
destination eq 1433 tcp service
network of the Demo_Server object
Home 89.234.126.12
Description server set up for the product demo
network of the Internal_Demo_Server object
Home 192.168.20.24
Internal description of the demo server IP address
network of the NETWORK_OBJ_192.168.20.0_24 object
subnet 192.168.20.0 255.255.255.0
network of the NETWORK_OBJ_192.168.50.0_26 object
255.255.255.192 subnet 192.168.50.0
network of the NETWORK_OBJ_192.168.0.0_16 object
Subnet 192.168.0.0 255.255.0.0
service object MSSQL
destination eq 1434 tcp service
MSSQL port description
VPN network object
192.168.50.0 subnet 255.255.255.0
network of the NETWORK_OBJ_192.168.50.0_24 object
192.168.50.0 subnet 255.255.255.0
service object TS
tcp destination eq 4400 service
service of the TS_Return object
tcp source eq 4400 service
network of the External_QA_3 object
Home 89.234.126.13
network of the Internal_QA_3 object
Home 192.168.20.25
network of the Dev_WebServer object
Home 192.168.20.27
network of the External_Dev_Web object
Home 89.234.126.14
network of the CIX_Subnet object
255.255.255.0 subnet 192.168.100.0
network of the NETWORK_OBJ_192.168.10.0_24 object
192.168.10.0 subnet 255.255.255.0
network of the NETWORK_OBJ_84.39.233.50 object
Home 84.39.233.50
network of the NETWORK_OBJ_92.51.193.158 object
Home 92.51.193.158
network of the NETWORK_OBJ_192.168.100.0_24 object
255.255.255.0 subnet 192.168.100.0
network of the NETWORK_OBJ_192.168.1.0_24 object
subnet 192.168.1.0 255.255.255.0
object-group service DM_INLINE_SERVICE_1
the tcp destination eq ftp service object
the purpose of the tcp destination eq netbios-ssn service
the purpose of the tcp destination eq smtp service
service-object TS
the Payback_Internal object-group network
object-network 192.168.10.0 255.255.255.0
object-network 192.168.20.0 255.255.255.0
object-network 192.168.40.0 255.255.255.0
object-group service DM_INLINE_SERVICE_3
the purpose of the service tcp destination eq www
the purpose of the tcp destination eq https service
service-object TS
service-object, object TS_Return
object-group service DM_INLINE_SERVICE_4
service-object RDP
the purpose of the service tcp destination eq www
the purpose of the tcp destination eq https service
object-group service DM_INLINE_SERVICE_5
purpose purpose of the MSSQL service
service-object RDP
service-object TS
object-group Protocol TCPUDP
object-protocol udp
object-tcp protocol
object-group service DM_INLINE_SERVICE_6
service-object TS
service-object, object TS_Return
the purpose of the service tcp destination eq www
the purpose of the tcp destination eq https service
Note to outside_access_in to access list that this rule allows Internet the interal server.
Notice on the outside_access_in of the access-list allowed:
Comment from outside_access_in-list of FTP access
Comment from outside_access_in-RDP access list
Comment from outside_access_in-list of SMTP access
Note to outside_access_in to access list Net Bios
Comment from outside_access_in-SQL access list
Comment from outside_access_in-list to access TS - 4400
outside_access_in list extended access allowed object object-group DM_INLINE_SERVICE_1 any4 Internal_Report_Server
access host access-list outside_access_in note rule internal QA
Notice on the outside_access_in of the access-list allowed:
Comment from outside_access_in-HTTP access list
Comment from outside_access_in-RDP access list
outside_access_in list extended access permitted tcp any4 object Internal_Host_QA eq www
Notice on the outside_access_in of the access-list access to the internal Web server:
Notice on the outside_access_in of the access-list allowed:
Comment from outside_access_in-HTTP access list
Comment from outside_access_in-RDP access list
outside_access_in list extended access allowed object object-group DM_INLINE_SERVICE_3 any4 Internal_QA_Web_Server
Note to outside_access_in to access list rule allowing access to the demo server
Notice on the outside_access_in of the access-list allowed:
Comment from outside_access_in-RDP access list
Comment from outside_access_in-list to access MSSQL
outside_access_in list extended access allowed object object-group DM_INLINE_SERVICE_4 any4 Internal_Demo_Server
outside_access_in list extended access allowed object-group DM_INLINE_SERVICE_5 any object Internal_QA_3
Note to outside_access_in access to the development Web server access list
outside_access_in list extended access allowed object-group DM_INLINE_SERVICE_6 any object Dev_WebServer
AnyConnect_Client_Local_Print deny any4 any4 ip extended access list
AnyConnect_Client_Local_Print list extended access permitted tcp any4 any4 eq lpd
Note AnyConnect_Client_Local_Print of access list IPP: Internet Printing Protocol
AnyConnect_Client_Local_Print list extended access permitted tcp any4 any4 eq 631
print the access-list AnyConnect_Client_Local_Print Note Windows port
AnyConnect_Client_Local_Print list extended access permitted tcp any4 any4 eq 9100
access-list AnyConnect_Client_Local_Print mDNS Note: multicast DNS protocol
AnyConnect_Client_Local_Print list extended access permit udp host 224.0.0.251 any4 eq 5353
AnyConnect_Client_Local_Print of access list LLMNR Note: link Local Multicast Name Resolution protocol
AnyConnect_Client_Local_Print list extended access permit udp host 224.0.0.252 any4 eq 5355
Note access list TCP/NetBIOS protocol AnyConnect_Client_Local_Print
AnyConnect_Client_Local_Print list extended access permitted tcp any4 any4 EQ. 137
AnyConnect_Client_Local_Print list extended access permitted udp any4 any4 eq netbios-ns
Payback_VPN_splitTunnelAcl list standard access allowed 192.168.20.0 255.255.255.0
permit outside_cryptomap to access extended list ip 192.168.10.0 255.255.255.0 192.168.100.0 255.255.255.0
pager lines 24
Enable logging
information recording console
asdm of logging of information
address record
the journaling recipient
level alerts
Outside 1500 MTU
Within 1500 MTU
MTU 1500 servers
MTU 1500 printers
MTU 1500 wireless
no failover
ICMP unreachable rate-limit 1 burst-size 1
ASDM image disk0: / asdm-711 - 52.bin
don't allow no asdm history
ARP timeout 14400
no permit-nonconnected arp
NAT (inside, outside) source Dynamics one interface
NAT (wireless, outdoors) source Dynamics one interface
NAT (servers, outside) no matter what source dynamic interface
NAT (servers, external) static source Internal_Report_Server Report_Server
NAT (servers, external) static source Internal_Host_QA Host_QA_Server
NAT (servers, external) static source Internal_QA_Web_Server Web_Server_QA_VM
NAT (servers, external) static source Internal_Demo_Server Demo_Server
NAT (servers, external) static source NETWORK_OBJ_192.168.20.0_24 NETWORK_OBJ_192.168.20.0_24 NETWORK_OBJ_192.168.50.0_24 NETWORK_OBJ_192.168.50.0_24 non-proxy-arp-search of route static destination
NAT (servers, external) static source Internal_QA_3 External_QA_3
NAT (servers, external) static source Dev_WebServer External_Dev_Web
NAT (inside, outside) static source NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.1.0_24 NETWORK_OBJ_192.168.1.0_24 non-proxy-arp-search of route static destination
NAT (inside, outside) static source NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.100.0_24 non-proxy-arp-search of route static destination
Access-group outside_access_in in interface outside
Route outside 0.0.0.0 0.0.0.0 92.51.193.157 1
Timeout xlate 03:00
Pat-xlate timeout 0:00:30
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
identity of the user by default-domain LOCAL
the ssh LOCAL console AAA authentication
Enable http server
http 192.168.10.0 255.255.255.0 inside
http 192.168.40.0 255.255.255.0 wireless
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac
Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-SHA-TRANS-aes - esp esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-TRANS-aes - esp esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-AES-128-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-192-SHA-TRANS esp-aes-192 esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-AES-192-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-192-MD5-TRANS esp-aes-192 esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-AES-192-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-256-SHA-TRANS esp-aes-256 esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-AES-256-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-256-MD5-TRANS esp-aes-256 esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-AES-256-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-3DES-SHA-TRANS esp-3des esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-3DES-MD5-TRANS esp-3des esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-3DES-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-DES-SHA-TRANS esp - esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-DES-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-DES-MD5-TRANS esp - esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-DES-MD5-TRANS mode transit
Crypto ipsec ikev2 AES256 ipsec-proposal
Protocol esp encryption aes-256
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 ipsec-proposal AES192
Protocol esp encryption aes-192
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 ipsec-proposal AES
Esp aes encryption protocol
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 proposal ipsec 3DES
Esp 3des encryption protocol
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 ipsec-proposal OF
encryption protocol esp
Esp integrity sha - 1, md5 Protocol
Crypto ipsec pmtu aging infinite - the security association
card crypto outside_map 1 match address outside_cryptomap
card crypto outside_map 1 set pfs
peer set card crypto outside_map 1 84.39.233.50
card crypto outside_map 1 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
outside_map card crypto 1 set ikev2 AES256 AES192 AES 3DES ipsec-proposal OF
outside_map interface card crypto outside
trustpool crypto ca policy
IKEv2 crypto policy 1
aes-256 encryption
integrity sha
Group 5
FRP sha
second life 86400
IKEv2 crypto policy 10
aes-192 encryption
integrity sha
Group 5
FRP sha
second life 86400
IKEv2 crypto policy 20
aes encryption
integrity sha
Group 5
FRP sha
second life 86400
IKEv2 crypto policy 30
3des encryption
integrity sha
Group 5
FRP sha
second life 86400
IKEv2 crypto policy 40
the Encryption
integrity sha
Group 5
FRP sha
second life 86400
Crypto ikev2 activate out of service the customer port 443
Crypto ikev1 allow outside
IKEv1 crypto policy 10
preshared authentication
3des encryption
sha hash
Group 2
life 86400
Telnet timeout 5
SSH 77.75.100.208 255.255.255.240 outside
SSH 192.168.10.0 255.255.255.0 inside
SSH 192.168.40.0 255.255.255.0 wireless
SSH timeout 5
Console timeout 0dhcpd 192.168.0.1 dns
dhcpd outside auto_config
!
dhcpd address 192.168.10.21 - 192.168.10.240 inside
dhcpd dns 192.168.20.21 83.147.160.2 interface inside
paybackloyalty.com dhcpd option 15 inside ascii interface
dhcpd allow inside
!
dhcpd address 192.168.40.21 - 192.168.40.240 Wireless
dhcpd dns 192.168.20.21 83.147.160.2 wireless interface
dhcpd update dns of the wireless interface
dhcpd option 15 ascii paybackloyalty.com wireless interface
dhcpd activate wireless
!
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
internal Payback_VPN group strategy
attributes of Group Policy Payback_VPN
VPN - 10 concurrent connections
Ikev1 VPN-tunnel-Protocol
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list Payback_VPN_splitTunnelAcl
attributes of Group Policy DfltGrpPolicy
value of 83.147.160.2 DNS server 83.147.160.130
VPN-tunnel-Protocol ikev1, ikev2 clientless ssl
internal GroupPolicy_84.39.233.50 group strategy
attributes of Group Policy GroupPolicy_84.39.233.50
VPN-tunnel-Protocol ikev1, ikev2
Noelle XB/IpvYaATP.2QYm username encrypted password
Noelle username attributes
VPN-group-policy Payback_VPN
type of remote access service
username Éanna encrypted password privilege 0 vXILR9ZZQIsd1Naw
Éanna attributes username
VPN-group-policy Payback_VPN
type of remote access service
Michael qpbleUqUEchRrgQX of encrypted password username
user name Michael attributes
VPN-group-policy Payback_VPN
type of remote access service
username, password from Danny .7fEXdzESUk6S/cC encrypted privilege 0
user name Danny attributes
VPN-group-policy Payback_VPN
type of remote access service
Aileen tytrelqvV5VRX2pz encrypted password privilege 0 username
user name Aileen attributes
VPN-group-policy Payback_VPN
type of remote access service
Aidan aDu6YH0V5XaxpEPg encrypted password privilege 0 username
Aidan username attributes
VPN-group-policy Payback_VPN
type of remote access service
username password 6e6Djaz3W/XH59zX gordon encrypted privilege 15
shane.c iqGMoWOnfO6YKXbw encrypted password username
username shane.c attributes
VPN-group-policy Payback_VPN
type of remote access service
Shane uYePLcrFadO9pBZx of encrypted password username
user name Shane attributes
VPN-group-policy Payback_VPN
type of remote access service
username, encrypted James TdYPv1pvld/hPM0d password
user name James attributes
VPN-group-policy Payback_VPN
type of remote access service
Mark yruxpddqfyNb.qFn of encrypted password username
user name brand attributes
type of service admin
username password of Mary XND5FTEiyu1L1zFD encrypted
user name Mary attributes
VPN-group-policy Payback_VPN
type of remote access service
Massimo vs65MMo4rM0l4rVu encrypted password privilege 0 username
Massimo username attributes
VPN-group-policy Payback_VPN
type of remote access service
type tunnel-group Payback_VPN remote access
attributes global-tunnel-group Payback_VPN
VPN1 address pool
Group Policy - by default-Payback_VPN
IPSec-attributes tunnel-group Payback_VPN
IKEv1 pre-shared-key *.
tunnel-group 84.39.233.50 type ipsec-l2l
tunnel-group 84.39.233.50 General-attributes
Group - default policy - GroupPolicy_84.39.233.50
IPSec-attributes tunnel-group 84.39.233.50
IKEv1 pre-shared-key *.
remote control-IKEv2 pre-shared-key authentication *.
pre-shared-key authentication local IKEv2 *.
!
Global class-card class
match default-inspection-traffic
!
!
World-Policy policy-map
Global category
inspect the dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
Review the ip options
inspect the netbios
inspect the pptp
inspect the rsh
inspect the rtsp
inspect the sip
inspect the snmp
inspect sqlnet
inspect sunrpc
inspect the tftp
inspect xdmcp
inspect the icmp error
inspect the icmp
!
service-policy-international policy global
192.168.20.21 SMTP server
context of prompt hostname
no remote anonymous reporting call
call-home
Profile of CiscoTAC-1
no active account
http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address
email address of destination [email protected] / * /
destination-mode http transport
Subscribe to alert-group diagnosis
Subscribe to alert-group environment
Subscribe to alert-group monthly periodic inventory
monthly periodicals to subscribe to alert-group configuration
daily periodic subscribe to alert-group telemetry
Cryptochecksum:d06974501eb0327a5ed229c8445f4fe1ASA 2
ASA Version 9.0 (1)
!
Payback-CIX hostname
activate the encrypted password of HSMurh79NVmatjY0
2KFQnbNIdI.2KYOU encrypted passwd
names of
!
interface Ethernet0/0
switchport access vlan 2
Speed 100
full duplex
!
interface Ethernet0/1
Description this port connects to the local network VIRTUAL 100
switchport access vlan 100
!
interface Ethernet0/2
!
interface Ethernet0/3
switchport access vlan 100
!
interface Ethernet0/4
switchport access vlan 100
!
interface Ethernet0/5
switchport access vlan 100
!
interface Ethernet0/6
switchport access vlan 100
!
interface Ethernet0/7
switchport access vlan 100
!
interface Vlan2
nameif outside
security-level 0
IP 84.39.233.50 255.255.255.240
!
interface Vlan100
nameif inside
security-level 100
IP 192.168.100.1 address 255.255.255.0
!
banner welcome to Payback loyalty - CIX connection line
passive FTP mode
summer time clock gmt/idt recurring last Sun Mar 01:00 last Sun Oct 02:00
DNS domain-lookup outside
DNS lookup field inside
DNS server-group defaultDNS
Name-Server 8.8.8.8
Server name 8.8.4.4
permit same-security-traffic inter-interface
network obj_any object
subnet 0.0.0.0 0.0.0.0
network of the host-CIX-1 object
host 192.168.100.2
Description This is the VM server host machine
network object host-External_CIX-1
Home 84.39.233.51
Description This is the external IP address of the server the server VM host
service object RDP
source between 1-65535 destination eq 3389 tcp service
network of the Payback_Office object
Home 92.51.193.158
service object MSQL
destination eq 1433 tcp service
network of the Development_OLTP object
Home 192.168.100.10
Description for Eiresoft VM
network of the External_Development_OLTP object
Home 84.39.233.52
Description This is the external IP address for the virtual machine for Eiresoft
network of the Eiresoft object
Home 146.66.160.70
Contractor s/n description
network of the External_TMC_Web object
Home 84.39.233.53
Description Public address to the TMC Web server
network of the TMC_Webserver object
Home 192.168.100.19
Internal description address TMC Webserver
network of the External_TMC_OLTP object
Home 84.39.233.54
External targets OLTP IP description
network of the TMC_OLTP object
Home 192.168.100.18
description of the interal target IP address
network of the External_OLTP_Failover object
Home 84.39.233.55
IP failover of the OLTP Public description
network of the OLTP_Failover object
Home 192.168.100.60
Server failover OLTP description
network of the servers object
subnet 192.168.20.0 255.255.255.0
being Wired network
192.168.10.0 subnet 255.255.255.0
the subject wireless network
192.168.40.0 subnet 255.255.255.0
network of the NETWORK_OBJ_192.168.100.0_24 object
255.255.255.0 subnet 192.168.100.0
network of the NETWORK_OBJ_192.168.10.0_24 object
192.168.10.0 subnet 255.255.255.0
network of the Eiresoft_2nd object
Home 137.117.217.29
Description 2nd Eiresoft IP
network of the Dev_Test_Webserver object
Home 192.168.100.12
Description address internal to the Test Server Web Dev
network of the External_Dev_Test_Webserver object
Home 84.39.233.56
Description This is the PB Dev Test Webserver
network of the NETWORK_OBJ_192.168.1.0_24 object
subnet 192.168.1.0 255.255.255.0
object-group service DM_INLINE_SERVICE_1
service-object MSQL
service-object RDP
object-group service DM_INLINE_SERVICE_2
service-object MSQL
service-object RDP
object-group service DM_INLINE_SERVICE_3
service-object MSQL
service-object RDP
object-group service DM_INLINE_SERVICE_4
service-object MSQL
service-object RDP
the tcp destination eq ftp service object
object-group service DM_INLINE_SERVICE_5
service-object MSQL
service-object RDP
the tcp destination eq ftp service object
object-group service DM_INLINE_SERVICE_6
service-object MSQL
service-object RDP
the Payback_Intrernal object-group network
object-network servers
Wired network-object
wireless network object
object-group service DM_INLINE_SERVICE_7
service-object MSQL
service-object RDP
object-group service DM_INLINE_SERVICE_8
service-object MSQL
service-object RDP
object-group service DM_INLINE_SERVICE_9
service-object MSQL
service-object RDP
object-group service DM_INLINE_SERVICE_10
service-object MSQL
service-object RDP
the tcp destination eq ftp service object
object-group service DM_INLINE_SERVICE_11
service-object RDP
the tcp destination eq ftp service object
outside_access_in list extended access allow object-group DM_INLINE_SERVICE_1 object Payback_Office object CIX-host-1
Note to access list OLTP Development Office of recovery outside_access_in
outside_access_in list extended access allow DM_INLINE_SERVICE_2 object Payback_Office object Development_OLTP object-group
Comment from outside_access_in-access Eiresoft access list
outside_access_in list extended access allow DM_INLINE_SERVICE_3 object Eiresoft object Development_OLTP object-group
outside_access_in list extended access allow DM_INLINE_SERVICE_4 object Payback_Office object TMC_Webserver object-group
Note to outside_access_in access to OLTP for target recovery Office Access list
outside_access_in list extended access allow DM_INLINE_SERVICE_5 object Payback_Office object TMC_OLTP object-group
outside_access_in list extended access allow DM_INLINE_SERVICE_6 object Payback_Office object OLTP_Failover object-group
Note to outside_access_in access-list that's allowing access of the Eiresoft on the failover OLTP server
outside_access_in list extended access allow DM_INLINE_SERVICE_7 object Eiresoft object OLTP_Failover object-group
Comment from outside_access_in-access list access for the 2nd period of INVESTIGATION of Eiresoft
outside_access_in list extended access allow DM_INLINE_SERVICE_8 object Eiresoft_2nd object Development_OLTP object-group
Note to outside_access_in access from the 2nd IP Eiresoft access list
outside_access_in list extended access allow DM_INLINE_SERVICE_9 object Eiresoft_2nd object OLTP_Failover object-group
outside_access_in list extended access allow DM_INLINE_SERVICE_10 object Payback_Office object Dev_Test_Webserver object-group
outside_access_in list extended access allow DM_INLINE_SERVICE_11 object Payback_Office object External_TMC_OLTP object-group
outside_cryptomap to access extended list ip 192.168.100.0 allow 255.255.255.0 192.168.10.0 255.255.255.0
pager lines 24
Enable logging
asdm of logging of information
Outside 1500 MTU
Within 1500 MTU
ICMP unreachable rate-limit 1 burst-size 1
don't allow no asdm history
ARP timeout 14400
no permit-nonconnected arp
NAT (inside, outside) source Dynamics one interface
NAT (inside, outside) static source CIX-host-1 External_CIX-host-1
NAT (inside, outside) static source Development_OLTP External_Development_OLTP
NAT (inside, outside) static source TMC_Webserver External_TMC_Web
NAT (inside, outside) static source TMC_OLTP External_TMC_OLTP
NAT (inside, outside) static source OLTP_Failover External_OLTP_Failover
NAT (inside, outside) static source Dev_Test_Webserver External_Dev_Test_Webserver
NAT (inside, outside) static source NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.10.0_24 non-proxy-arp-search of route static destination
NAT (inside, outside) static source NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.1.0_24 NETWORK_OBJ_192.168.1.0_24 non-proxy-arp-search of route static destination
Access-group outside_access_in in interface outside
Route outside 0.0.0.0 0.0.0.0 84.39.233.49 1
Timeout xlate 03:00
Pat-xlate timeout 0:00:30
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
identity of the user by default-domain LOCAL
the ssh LOCAL console AAA authentication
Enable http server
http 92.51.193.156 255.255.255.252 outside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown warmstart of cold start
Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-SHA-TRANS-aes - esp esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-TRANS-aes - esp esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-AES-128-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-192-SHA-TRANS esp-aes-192 esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-AES-192-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-192-MD5-TRANS esp-aes-192 esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-AES-192-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-256-SHA-TRANS esp-aes-256 esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-AES-256-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-256-MD5-TRANS esp-aes-256 esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-AES-256-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-3DES-SHA-TRANS esp-3des esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-3DES-MD5-TRANS esp-3des esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-3DES-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-DES-SHA-TRANS esp - esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-DES-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-DES-MD5-TRANS esp - esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-DES-MD5-TRANS mode transit
Crypto ipsec ikev2 ipsec-proposal OF
encryption protocol esp
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 proposal ipsec 3DES
Esp 3des encryption protocol
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 ipsec-proposal AES
Esp aes encryption protocol
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 ipsec-proposal AES192
Protocol esp encryption aes-192
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 AES256 ipsec-proposal
Protocol esp encryption aes-256
Esp integrity sha - 1, md5 Protocol
Crypto ipsec pmtu aging infinite - the security association
card crypto outside_map 1 match address outside_cryptomap
card crypto outside_map 1 set pfs
peer set card crypto outside_map 1 92.51.193.158
card crypto outside_map 1 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
outside_map card crypto 1jeu ikev2 AES AES192 AES256 3DES ipsec-proposal
outside_map interface card crypto outside
trustpool crypto ca policy
IKEv2 crypto policy 1
aes-256 encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 10
aes-192 encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 20
aes encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 30
3des encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 40
the Encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
Crypto ikev2 allow outside
Crypto ikev1 allow outside
IKEv1 crypto policy 10
authentication crack
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 20
authentication rsa - sig
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 30
preshared authentication
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 40
authentication crack
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 50
authentication rsa - sig
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 60
preshared authentication
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 70
authentication crack
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 80
authentication rsa - sig
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 90
preshared authentication
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 100
authentication crack
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 110
authentication rsa - sig
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 120
preshared authentication
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 130
authentication crack
the Encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 140
authentication rsa - sig
the Encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 150
preshared authentication
the Encryption
sha hash
Group 2
life 86400
Telnet timeout 5
SSH 77.75.100.208 255.255.255.240 outside
SSH 92.51.193.156 255.255.255.252 outside
SSH timeout 5
Console timeout 0dhcpd outside auto_config
!
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
internal GroupPolicy_92.51.193.158 group strategy
attributes of Group Policy GroupPolicy_92.51.193.158
VPN-tunnel-Protocol ikev1, ikev2
username password 6e6Djaz3W/XH59zX gordon encrypted privilege 15
tunnel-group 92.51.193.158 type ipsec-l2l
tunnel-group 92.51.193.158 General-attributes
Group - default policy - GroupPolicy_92.51.193.158
IPSec-attributes tunnel-group 92.51.193.158
IKEv1 pre-shared-key *.
remote control-IKEv2 pre-shared-key authentication *.
pre-shared-key authentication local IKEv2 *.
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
Review the ip options
inspect the icmp
!
global service-policy global_policy
context of prompt hostname
no remote anonymous reporting call
Cryptochecksum:83b2069fa311e6037163ae74f9b2bec2
: endHello
There are some clear problems I see on a quick glance. These are not related to the actual VPN configuration but rather the NAT configurations.
All your configuration of NAT CLI format above are configured as manual NAT / double NAT in Section 1. This means that the appliance NAT configurations have been added to the same section of the NAT configurations and scheduling of the NAT inside this Section rules is the cause of the problem for the L2L VPN connection for some.
Here are a few suggestions on what to change
ASA1
Minimal changes
the object of the LAN network
192.168.10.0 subnet 255.255.255.0
being REMOTE-LAN network
255.255.255.0 subnet 192.168.100.0
NAT (inside, outside) 1 static source LAN LAN to static destination REMOTE - LAN LAN
no nat source (indoor, outdoor) public static NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.100.0_24 non-proxy-arp-search of route static destination
That means foregoing is first of all create 'object' that contain the local LAN and remote LANs. Then, it creates a NAT0 rule and adds to the top rules NAT. (number 1). It is essentially of at least one of the problems preventing the VPN operation or traffic that cross.
Finally, we remove the old rule that generated the ASDM. It would do the same thing if it has been moved to the top, but I generally find the creation of the 'object' with descriptive names easier on the eyes in the long term.
Other suggestions
These changes are not necessary with regard to the VPN L2L. Here are some suggestions how to clean a part of NAT configurations.
PAT-SOURCE network object-group
source networks internal PAT Description
object-network 192.168.10.0 255.255.255.0
object-network 192.168.20.0 255.255.255.0
object-network 192.168.40.0 255.255.255.0
NAT interface (it is, outside) the after-service automatic PAT-SOURCE dynamic source
No source (indoor, outdoor) nat Dynamics one interface
no nat (wireless, outdoors) source Dynamics one interface
no nat (servers, outside) no matter what source dynamic interface
The above configuration creates a "object-group" that lists all internal networks that you have dynamic PAT configured so far. It then uses the ' object-group ' in a command unique 'nat' to manage the dynamic PAT for all internal networks (with the exception of printers who had nothing at first). Then we remove the old PAT dynamic configurations.
Contains the command "nat" "car after" because it moving this "nat" configuration to the bottom of the NAT rules. For this reason its less likely to cause problems in the future.
network of the SERVERS object
subnet 192.168.20.0 255.255.255.0
network of the VPN-POOL object
192.168.50.0 subnet 255.255.255.0
NAT (servers, external) 2 static static source of destination of SERVERS SERVERS VPN-VPN-POOL
no nat (servers, external) static source NETWORK_OBJ_192.168.20.0_24 NETWORK_OBJ_192.168.20.0_24 NETWORK_OBJ_192.168.50.0_24 NETWORK_OBJ_192.168.50.0_24 non-proxy-arp-search of route static destination
The above configuration is supposed to create a NAT0 configuration for traffic between the network and the pool of Client VPN server. To my knowledge the old configuration that remove us is not used because the traffic would have matched PAT rule dynamic server yet rather than this rule which is later in the NAT configurations and would not be addressed.
no nat source (indoor, outdoor) public static NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.1.0_24 NETWORK_OBJ_192.168.1.0_24 non-proxy-arp-search of route static destination
It seems to me that network 192.168.1.0/24 is not configured from anywhere in your network. Therefore, the above 'nat' configuration seems useless, can be deleted. If I missed something and its use in then of course do not remove it.
ASA2
Minimal changes
the object of the LAN network
255.255.255.0 subnet 192.168.100.0
being REMOTE-LAN network
192.168.10.0 subnet 255.255.255.0
NAT (inside, outside) 1 static source LAN LAN to static destination REMOTE - LAN LAN
no nat source (indoor, outdoor) public static NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.10.0_24 non-proxy-arp-search of route static destination
That means foregoing is first of all create 'object' that contain the local LAN and remote LANs. Then, it creates a NAT0 rule and adds to the top rules NAT. (number 1). It is essentially of at least one of the problems preventing the VPN operation or traffic that cross.
Finally, we remove the old rule that generated the ASDM.
Other suggestions
PAT-SOURCE network object-group
object-network 192.168.100.0 255.255.255.0
NAT interface (it is, outside) the after-service automatic PAT-SOURCE dynamic source
No source (indoor, outdoor) nat Dynamics one interface
The above configuration is supposed to do the same thing with the other ASA. Although given that this network contains only a single subnet it cleans the "nat" configurations exist that much. But the order of the "nat" configurations is changed to avoid further problems with the NAT order.
no nat source (indoor, outdoor) public static NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.100.0_24 NETWORK_OBJ_192.168.1.0_24 NETWORK_OBJ_192.168.1.0_24 non-proxy-arp-search of route static destination
It seems to me that network 192.168.1.0/24 is not configured from anywhere in your network. Therefore, the above 'nat' configuration seems useless, can be deleted. If I missed something and its use in then of course do not remove it.
I suggest trying the changes related to VPN L2L first NAT0 configurations and test traffic. So who gets the work of connectivity, then you could consider changing other NAT configurations. There are other things that could be changed also in what concerns THAT static NAT servers but that probably better left for another time.
Hope this makes any sense and has helped
Remember to mark a reply as the answer if it answered your question.
Feel free to ask more if necessary
-Jouni
-
Failover on Cisco ASA 5505 with EasyVPN
Hello
I've implemented a customer EasyVPN with a Cisco ASA 5505 and I am trying to configure the failover but I get this message:
"Failover cannot be configured as Cisco Easy VPN remote is activated."
However, I have seen in the link below, this dynamic rollover is compatible with the easy standard (and not with improved but I don't think I use easyVPN improved).
http://www.Cisco.com/c/en/us/products/collateral/security/iOS-easy-VPN/e...
The configuration I did through ASDM is very simple:
vpnclient server * * *.
vpnclient-mode client mode
vpngroup vpnclient * password *.
vpnclient username * password *.
vpnclient enableMy question is how can I implement failover with a client on a Cisco ASA 5505 EasyVPN?
Thanks in advance
You cannot configure the failover of a device that acts as a client
-
Problem with the VPN site to site for the two cisco asa 5505
Starting with cisco asa. I wanted to do a vpn site-to site of cisco. I need help. I can't ping from site A to site B and vice versa.
Cisco Config asa1
interface Ethernet0/0
switchport access vlan 1
!
interface Ethernet0/1
switchport access vlan 2
!
interface Vlan1
nameif outside
security-level 0
IP address 172.xxx.xx.4 255.255.240.0
!
interface Vlan2
nameif inside
security-level 100
IP 192.168.60.2 255.255.255.0
!
passive FTP mode
network of the Lan_Outside object
192.168.60.0 subnet 255.255.255.0
network of the NETWORK_OBJ_192.168.1.0_24 object
subnet 192.168.1.0 255.255.255.0
network of the NETWORK_OBJ_192.168.60.0_24 object
192.168.60.0 subnet 255.255.255.0
object-group Protocol DM_INLINE_PROTOCOL_1
ip protocol object
icmp protocol object
object-group Protocol DM_INLINE_PROTOCOL_2
ip protocol object
icmp protocol object
object-group Protocol DM_INLINE_PROTOCOL_3
ip protocol object
icmp protocol object
Access extensive list ip 192.168.60.0 Outside_cryptomap allow 255.255.255.0 192.168.1.0 255.255.255.0
Outside_cryptomap list extended access allow DM_INLINE_PROTOCOL_3 of object-group a
Outside_access_in list extended access allow DM_INLINE_PROTOCOL_1 of object-group a
Inside_access_in list extended access allow DM_INLINE_PROTOCOL_2 of object-group a
network of the Lan_Outside object
NAT (inside, outside) interface dynamic dns
Access-group Outside_access_in in interface outside
Inside_access_in access to the interface inside group
Route outside 0.0.0.0 0.0.0.0 172.110.xx.1 1
Timeout xlate 03:00
Pat-xlate timeout 0:00:30
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
identity of the user by default-domain LOCAL
AAA authentication http LOCAL console
Enable http server
http 192.168.60.0 255.255.255.0 inside
http 96.xx.xx.222 255.255.255.255 outside
No snmp server location
No snmp Server contact
Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-SHA-TRANS-aes - esp esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-TRANS-aes - esp esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-AES-128-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-192-SHA-TRANS esp-aes-192 esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-AES-192-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-192-MD5-TRANS esp-aes-192 esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-AES-192-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-256-SHA-TRANS esp-aes-256 esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-AES-256-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-256-MD5-TRANS esp-aes-256 esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-AES-256-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-3DES-SHA-TRANS esp-3des esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-3DES-MD5-TRANS esp-3des esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-3DES-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-DES-SHA-TRANS esp - esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-DES-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-DES-MD5-TRANS esp - esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-DES-MD5-TRANS mode transit
Crypto ipsec ikev2 ipsec-proposal OF
encryption protocol esp
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 proposal ipsec 3DES
Esp 3des encryption protocol
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 ipsec-proposal AES
Esp aes encryption protocol
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 ipsec-proposal AES192
Protocol esp encryption aes-192
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 AES256 ipsec-proposal
Protocol esp encryption aes-256
Esp integrity sha - 1, md5 Protocol
Crypto ipsec pmtu aging infinite - the security association
card crypto Outside_map 1 corresponds to the address Outside_cryptomap
card crypto Outside_map 1 set peer 96.88.75.222
card crypto Outside_map 1 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
card crypto Outside_map 1 set ikev2 AES256 AES192 AES 3DES ipsec-proposal OF
Outside_map interface card crypto outside
trustpool crypto ca policy
IKEv2 crypto policy 1
aes-256 encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 10
aes-192 encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 20
aes encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 30
3des encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 40
the Encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
Crypto ikev2 allow outside
Crypto ikev1 allow outside
IKEv1 crypto policy 10
authentication crack
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 20
authentication rsa - sig
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 30
preshared authentication
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 40
authentication crack
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 50
authentication rsa - sig
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 60
preshared authentication
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 70
authentication crack
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 80
authentication rsa - sig
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 90
preshared authentication
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 100
authentication crack
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 110
authentication rsa - sig
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 120
preshared authentication
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 130
authentication crack
the Encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 140
authentication rsa - sig
the Encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 150
preshared authentication
the Encryption
sha hash
Group 2
life 86400
Telnet timeout 5
SSH stricthostkeycheck
SSH timeout 5
SSH group dh-Group1-sha1 key exchange
Console timeout 0
inside access managementdhcpd address 192.168.60.50 - 192.168.60.100 inside
dhcpd allow inside
!
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
WebVPN
AnyConnect essentials
internal GroupPolicy_96.xx.xx.222 group strategy
attributes of Group Policy GroupPolicy_96.xx.xx.222
VPN-tunnel-Protocol ikev1, ikev2
username admin privilege 15 encrypted password f3UhLvUj1QsXsuK7
tunnel-group 96.xx.xx.222 type ipsec-l2l
tunnel-group 96.xx.xx.222 General-attributes
Group - default policy - GroupPolicy_96.xx.xx.222
96.XX.XX.222 group of tunnel ipsec-attributes
IKEv1 pre-shared-key *.
remote control-IKEv2 pre-shared-key authentication *.
pre-shared-key authentication local IKEv2 *.
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
Review the ip options
inspect the icmp
inspect the icmp error---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Cisco ASA 2 config
interface Ethernet0/0
switchport access vlan 1
!
interface Ethernet0/1
switchport access vlan 2
!
interface Vlan1
nameif outside
security-level 0
IP address 96.xx.xx.222 255.255.255.248
!
interface Vlan2
nameif inside
security-level 100
IP 192.168.1.254 255.255.255.0
!
passive FTP mode
permit same-security-traffic inter-interface
permit same-security-traffic intra-interface
network of the Lan_Outside object
subnet 192.168.1.0 255.255.255.0
network of the NETWORK_OBJ_192.168.60.0_24 object
192.168.60.0 subnet 255.255.255.0
network of the NETWORK_OBJ_192.168.1.0_24 object
subnet 192.168.1.0 255.255.255.0
object-group Protocol DM_INLINE_PROTOCOL_1
ip protocol object
icmp protocol object
object-group Protocol DM_INLINE_PROTOCOL_2
ip protocol object
icmp protocol object
object-group Protocol DM_INLINE_PROTOCOL_3
ip protocol object
icmp protocol object
object-group Protocol DM_INLINE_PROTOCOL_4
ip protocol object
icmp protocol object
Outside_cryptomap list extended access allow DM_INLINE_PROTOCOL_2 of object-group 192.168.1.0 255.255.255.0 192.168.60.0 255.255.255.0
Outside_cryptomap list extended access allow DM_INLINE_PROTOCOL_3 of object-group a
Outside_access_in list extended access allow DM_INLINE_PROTOCOL_1 of object-group a
Inside_access_in list extended access allow DM_INLINE_PROTOCOL_4 of object-group a
pager lines 24
Enable logging
asdm of logging of information
Outside 1500 MTU
Within 1500 MTU
no failover
ICMP unreachable rate-limit 1 burst-size 1
don't allow no asdm history
ARP timeout 14400
no permit-nonconnected arp
NAT (inside, outside) static source NETWORK_OBJ_192.168.1.0_24 NETWORK_OBJ_192.168.1.0_24 NETWORK_OBJ_192.168.60.0_24 NETWORK_OBJ_192.168.60.0_24 non-proxy-arp-search of route static destination
!
network of the Lan_Outside object
dynamic NAT (all, outside) interface
Access-group Outside_access_in in interface outside
Inside_access_in access to the interface inside group
Route outside 0.0.0.0 0.0.0.0 96.xx.xx.217 1
Timeout xlate 03:00
Pat-xlate timeout 0:00:30
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
identity of the user by default-domain LOCAL
AAA authentication http LOCAL console
Enable http server
http 192.168.1.0 255.255.255.0 inside
http 172.xxx.xx.4 255.255.255.255 outside
No snmp server location
No snmp Server contact
Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-SHA-TRANS-aes - esp esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-TRANS-aes - esp esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-AES-128-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-192-SHA-TRANS esp-aes-192 esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-AES-192-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-192-MD5-TRANS esp-aes-192 esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-AES-192-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-256-SHA-TRANS esp-aes-256 esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-AES-256-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-256-MD5-TRANS esp-aes-256 esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-AES-256-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-3DES-SHA-TRANS esp-3des esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-3DES-MD5-TRANS esp-3des esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-3DES-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-DES-SHA-TRANS esp - esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-DES-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-DES-MD5-TRANS esp - esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-DES-MD5-TRANS mode transit
Crypto ipsec ikev2 ipsec-proposal OF
encryption protocol esp
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 proposal ipsec 3DES
Esp 3des encryption protocol
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 ipsec-proposal AES
Esp aes encryption protocol
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 ipsec-proposal AES192
Protocol esp encryption aes-192
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 AES256 ipsec-proposal
Protocol esp encryption aes-256
Esp integrity sha - 1, md5 Protocol
Crypto ipsec pmtu aging infinite - the security association
card crypto Outside_map 1 corresponds to the address Outside_cryptomap
card crypto Outside_map 1 set peer 172.110.74.4
card crypto Outside_map 1 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
card crypto Outside_map 1 set ikev2 AES256 AES192 AES 3DES ipsec-proposal OF
Outside_map interface card crypto outside
trustpool crypto ca policy
IKEv2 crypto policy 1
aes-256 encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 10
aes-192 encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 20
aes encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 30
3des encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 40
the Encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
Crypto ikev2 allow outside
Crypto ikev1 allow outside
IKEv1 crypto policy 10
authentication crack
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 20
authentication rsa - sig
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 30
preshared authentication
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 40
authentication crack
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 50
authentication rsa - sig
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 60
preshared authentication
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 70
authentication crack
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 80
authentication rsa - sig
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 90
preshared authentication
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 100
authentication crack
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 110
authentication rsa - sig
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 120
preshared authentication
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 130
authentication crack
the Encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 140
authentication rsa - sig
the Encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 150
preshared authentication
the Encryption
sha hash
Group 2
life 86400
Telnet timeout 5
SSH stricthostkeycheck
SSH timeout 5
SSH group dh-Group1-sha1 key exchange
Console timeout 0dhcpd address 192.168.1.50 - 192.168.1.100 inside
dhcpd allow inside
!
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
WebVPN
AnyConnect essentials
internal GroupPolicy_172.xxx.xx.4 group strategy
attributes of Group Policy GroupPolicy_172.xxx.xx.4
L2TP ipsec VPN-tunnel-Protocol ikev1, ikev2
username admin privilege 15 encrypted password f3UhLvUj1QsXsuK7
tunnel-group 172.xxx.xx.4 type ipsec-l2l
tunnel-group 172.xxx.xx.4 General-attributes
Group - default policy - GroupPolicy_172.xxx.xx.4
172.xxx.XX.4 group of tunnel ipsec-attributes
IKEv1 pre-shared-key *.
remote control-IKEv2 pre-shared-key authentication *.
pre-shared-key authentication local IKEv2 *.
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
Review the ip options
inspect the icmp
inspect the icmp error
inspect the httpFor IKEv2 configuration: (example config, you can change to encryption, group,...)
-You must add the declaration of exemption nat (see previous answer).
-set your encryption domain ACLs:
access-list-TRAFFIC IPSEC allowed extended LOCAL REMOTE - LAN LAN ip
-Set the Phase 1:
Crypto ikev2 allow outside
IKEv2 crypto policy 10
3des encryption
the sha md5 integrity
Group 5
FRP sha
second life 86400-Set the Phase 2:
Crypto ipsec ikev2 ipsec IKEV2-PROPOSAL
Esp aes encryption protocol
Esp integrity sha-1 protocol-set the Group of tunnel
tunnel-group REMOTE-PUBLIC-IP type ipsec-l2l
REMOTE-PUBLIC-IP tunnel-group ipsec-attributes
IKEv2 authentication remote pre-shared-key cisco123
IKEv2 authentication local pre-shared-key cisco123-Define the encryption card
address for correspondence CRYPTOMAP 10 - TRAFFIC IPSEC crypto map
card crypto CRYPTOMAP 10 peer set REMOTE-PUBLIC-IP
card crypto CRYPTOMAP 10 set ipsec ikev2-IKEV2-PROPOSAL
CRYPTOMAP interface card crypto outside
crypto isakmp identity addressOn your config, you have all these commands but on your VPN config, you mix ikev1 and ikev2. You have also defined political different ikev2. Just do a bit of cleaning and reached agreement on a 1 strategy for the two site (encryption, hash,...)
Thank you
-
EzVPN between Cisco ASA 5505 (with NEM mode) and Ciscoo 881 Roure
Hi friends,
I configured the Cisco ASA 5505 and Cisco router with DMVPN 881. 3 offices works very well but one office remains failure. I did the same configuration for all facilities but this router does not work. Any ideas?
Please find below the exit of 881 router Cisco:
YF2_Tbilisi_router #.
* 4 August 09:31:26.793: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH...
* 09:31:26.793 4 August: ISAKMP (0): increment the count of errors on his, try 4 out 5: retransmit the phase 1
* 4 August 09:31:26.793: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH
* 4 August 09:31:26.793: ISAKMP: (0): 1.1.1.1 package sending 500 peer_port 500 (I) my_port AG_INIT_EXCH
* 09:31:26.793 4 August: ISAKMP: (0): sending a packet IPv4 IKE.
* 4 August 09:31:36.793: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH...
* 09:31:36.793 4 August: ISAKMP (0): increment the count of errors on his, try 5 of 5: retransmit the phase 1
* 4 August 09:31:36.793: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH
* 4 August 09:31:36.793: ISAKMP: (0): 1.1.1.1 package sending 500 peer_port 500 (I) my_port AG_INIT_EXCH
* 09:31:36.793 4 August: ISAKMP: (0): sending a packet IPv4 IKE.
* 09:31:44.929 4 August: ISAKMP: (0): serving SA., its is 88961 B 34, delme is 88961 B 34
* 4 August 09:31:46.793: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH...
* 09:31:46.793 4 August: ISAKMP: (0): the peer is not paranoid KeepAlive.* 09:31:46.793 4 August: ISAKMP: (0): removal of reason ITS status of 'Death by retransmission P1' (I) AG_INIT_EXCH (peer 1.1.1.1)
* 09:31:46.793 4 August: % CRYPTO-6-EZVPN_CONNECTION_DOWN: user (customer) = group = Youth_Facility_2 Server_public_addr = 1.1.1.1
* 4 August 09:31:46.793: ISAKMP:isadb_key_addr_delete: no key for address 1.1.1.1 (root NULL)
* 09:31:46.793 4 August: ISAKMP: (0): removal of reason ITS status of 'Death by retransmission P1' (I) AG_INIT_EXCH (peer 1.1.1.1)
* 09:31:46.793 4 August: ISAKMP: Unlocking counterpart struct 0x8AA90C50 for isadb_mark_sa_deleted(), count 0
* 09:31:46.793 4 August: ISAKMP: delete peer node by peer_reap for 1.1.1.1: 8AA90C50
* 09:31:46.793 4 August: ISAKMP: (0): entry = IKE_MESG_INTERNAL, IKE_PHASE1_DEL
* 09:31:46.793 4 August: ISAKMP: (0): former State = new State IKE_I_AM1 = IKE_DEST_SA* 4 August 09:31:47.805: del_node 2.2.2.2 src dst 1.1.1.1:500 fvrf 0 x 0, ivrf 0 x 0
* 09:31:47.805 4 August: ISAKMP: (0): the peer is not paranoid KeepAlive.* 4 August 09:31:47.805: ISAKMP: (0): profile of THE request is (NULL)
* 09:31:47.805 4 August: ISAKMP: created a struct peer 1.1.1.1, peer port 500
* 09:31:47.805 4 August: ISAKMP: new created position = 0x8AA90C50 peer_handle = 0 x 80004819
* 09:31:47.805 4 August: ISAKMP: lock struct 0x8AA90C50, refcount 1 to peer isakmp_initiator
* 09:31:47.805 4 August: ISAKMP: (0): client configuration parameters 87531228 adjustment
* 09:31:47.805 4 August: ISAKMP: 500 local port, remote port 500
* 09:31:47.805 4 August: ISAKMP: find a dup her to the tree during his B 88961, 34 = isadb_insert call BVA
* 4 August 09:31:47.805: ISAKMP: (0): set up client mode.
* 4 August 09:31:47.805: ISAKMP: (0): built of NAT - T of the seller-rfc3947 ID
* 4 August 09:31:47.805: ISAKMP: (0): built the seller-07 ID NAT - t
* 4 August 09:31:47.805: ISAKMP: (0): built of NAT - T of the seller-03 ID
* 4 August 09:31:47.805: ISAKMP: (0): built the seller-02 ID NAT - t
* 4 August 09:31:47.805: ISKAMP: more send buffer from 1024 to 3072
* 09:31:47.805 4 August: ISAKMP: (0): ITS been pre-shared key and XAUTH authentication using id ID_KEY_ID type
* 09:31:47.805 4 August: ISAKMP (0): payload ID
next payload: 13
type: 11
Group ID: Youth_Facility_2
Protocol: 17
Port: 0
Length: 24
* 09:31:47.805 4 August: ISAKMP: (0): the total payload length: 24
* 09:31:47.809 4 August: ISAKMP: (0): entry = IKE_MESG_FROM_IPSEC, IKE_SA_REQ_AM
* 09:31:47.809 4 August: ISAKMP: (0): former State = new State IKE_READY = IKE_I_AM1* 4 August 09:31:47.809: ISAKMP: (0): Beginner aggressive Mode Exchange
* 4 August 09:31:47.809: ISAKMP: (0): 1.1.1.1 package sending 500 peer_port 500 (I) my_port AG_INIT_EXCH
* 09:31:47.809 4 August: ISAKMP: (0): sending a packet IPv4 IKE.
* 4 August 09:31:57.809: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH...
* 09:31:57.809 4 August: ISAKMP (0): increment the count of errors on his, try 1 5: retransmit the phase 1
* 4 August 09:31:57.809: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH
* 4 August 09:31:57.809: ISAKMP: (0): 1.1.1.1 package sending 500 peer_port 500 (I) my_port AG_INIT_EXCH
* 09:31:57.809 4 August: ISAKMP: (0): sending a packet IPv4 IKE.
* 4 August 09:32:07.809: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH...
* 09:32:07.809 4 August: ISAKMP (0): increment the count of errors on his, try 2 of 5: retransmit the phase 1
* 4 August 09:32:07.809: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH
* 4 August 09:32:07.809: ISAKMP: (0): 1.1.1.1 package sending 500 peer_port 500 (I) my_port AG_INIT_EXCH
* 09:32:07.809 4 August: ISAKMP: (0): sending a packet IPv4 IKE.
* 4 August 09:32:17.809: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH...
* 09:32:17.809 4 August: ISAKMP (0): increment the count of errors on his, try 3 of 5: retransmit the phase 1
* 4 August 09:32:17.809: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH
* 4 August 09:32:17.809: ISAKMP: (0): 1.1.1.1 package sending 500 peer_port 500 (I) my_port AG_INIT_EXCH
* 09:32:17.809 4 August: ISAKMP: (0): sending a packet IPv4 IKE.
* 4 August 09:32:27.809: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH...
* 09:32:27.809 4 August: ISAKMP (0): increment the count of errors on his, try 4 out 5: retransmit the phase 1
* 4 August 09:32:27.809: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH
* 4 August 09:32:27.809: ISAKMP: (0): 1.1.1.1 package sending 500 peer_port 500 (I) my_port AG_INIT_EXCH
* 09:32:27.809 4 August: ISAKMP: (0): sending a packet IPv4 IKE.
* 4 August 09:32:37.809: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH...
* 09:32:37.809 4 August: ISAKMP (0): increment the count of errors on his, try 5 of 5: retransmit the phase 1
* 4 August 09:32:37.809: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH
* 4 August 09:32:37.809: ISAKMP: (0): 1.1.1.1 package sending 500 peer_port 500 (I) my_port AG_INIT_EXCH
* 09:32:37.809 4 August: ISAKMP: (0): sending a packet IPv4 IKE.
* 09:32:46.793 4 August: ISAKMP: (0): serving SA., his is 872E1504, delme is 872E1504
* 4 August 09:32:47.809: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH...
* 09:32:47.809 4 August: ISAKMP: (0): the peer is not paranoid KeepAlive.* 09:32:47.809 4 August: ISAKMP: (0): removal of reason ITS status of 'Death by retransmission P1' (I) AG_INIT_EXCH (peer 1.1.1.1)
* 09:32:47.809 4 August: % CRYPTO-6-EZVPN_CONNECTION_DOWN: user (customer) = group = Youth_Facility_2 Server_public_addr = 1.1.1.1
* 4 August 09:32:47.809: ISAKMP:isadb_key_addr_delete: no key for address 1.1.1.1 (root NULL)
* 09:32:47.809 4 August: ISAKMP: (0): removal of reason ITS status of 'Death by retransmission P1' (I) AG_INIT_EXCH (peer 1.1.1.1)
* 09:32:47.809 4 August: ISAKMP: Unlocking counterpart struct 0x8AA90C50 for isadb_mark_sa_deleted(), count 0
* 09:32:47.809 4 August: ISAKMP: delete peer node by peer_reap for 1.1.1.1: 8AA90C50
* 09:32:47.809 4 August: ISAKMP: (0): entry = IKE_MESG_INTERNAL, IKE_PHASE1_DEL
* 09:32:47.809 4 August: ISAKMP: (0): former State = new State IKE_I_AM1 = IKE_DEST_SA* 4 August 09:32:48.909: del_node src 2.2.2.2:500 dst 1.1.1.1:500 fvrf 0 x 0, ivrf 0 x 0
* 09:32:48.909 4 August: ISAKMP: (0): the peer is not paranoid KeepAlive.* 4 August 09:32:48.909: ISAKMP: (0): profile of THE request is (NULL)
* 09:32:48.909 4 August: ISAKMP: created a struct peer 1.1.1.1, peer port 500
* 09:32:48.909 4 August: ISAKMP: new created position = 0x8AA90C50 peer_handle = 0 x 80004818
* 09:32:48.909 4 August: ISAKMP: lock struct 0x8AA90C50, refcount 1 to peer isakmp_initiator
* 09:32:48.909 4 August: ISAKMP: (0): client setting Configuration parameters 88C05A48
* 09:32:48.909 4 August: ISAKMP: 500 local port, remote port 500
* 09:32:48.909 4 August: ISAKMP: find a dup her to the tree during the isadb_insert his 87B57D38 = call BVA
* 4 August 09:32:48.909: ISAKMP: (0): set up client mode.
* 4 August 09:32:48.909: ISAKMP: (0): built of NAT - T of the seller-rfc3947 ID
* 4 August 09:32:48.909: ISAKMP: (0): built the seller-07 ID NAT - t
* 4 August 09:32:48.909: ISAKMP: (0): built of NAT - T of the seller-03 ID
* 4 August 09:32:48.909: ISAKMP: (0): built the seller-02 ID NAT - t
* 4 August 09:32:48.909: ISKAMP: more send buffer from 1024 to 3072
* 09:32:48.913 4 August: ISAKMP: (0): ITS been pre-shared key and XAUTH authentication using id ID_KEY_ID type
* 09:32:48.913 4 August: ISAKMP (0): payload ID
next payload: 13
type: 11
Group ID: Youth_Facility_2
Protocol: 17
Port: 0
Length: 24
* 09:32:48.913 4 August: ISAKMP: (0): the total payload length: 24
* 09:32:48.913 4 August: ISAKMP: (0): entry = IKE_MESG_FROM_IPSEC, IKE_SA_REQ_AM
* 09:32:48.913 4 August: ISAKMP: (0): former State = new State IKE_READY = IKE_I_AM1* 4 August 09:32:48.913: ISAKMP: (0): Beginner aggressive Mode Exchange
* 4 August 09:32:48.913: ISAKMP: (0): 1.1.1.1 package sending 500 peer_port 500 (I) my_port AG_INIT_EXCH
* 09:32:48.913 4 August: ISAKMP: (0): sending a packet IPv4 IKE.
* 4 August 09:32:58.913: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH...
* 09:32:58.913 4 August: ISAKMP (0): increment the count of errors on his, try 1 5: retransmit the phase 1
* 4 August 09:32:58.913: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH
* 4 August 09:32:58.913: ISAKMP: (0): 1.1.1.1 package sending 500 peer_port 500 (I) my_port AG_INIT_EXCH
* 09:32:58.913 4 August: ISAKMP: (0): sending a packet IPv4 IKE.
* 4 August 09:33:08.913: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH...
* 09:33:08.913 4 August: ISAKMP (0): increment the count of errors on his, try 2 of 5: retransmit the phase 1
* 4 August 09:33:08.913: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH
* 4 August 09:33:08.913: ISAKMP: (0): 1.1.1.1 package sending 500 peer_port 500 (I) my_port AG_INIT_EXCH
* 09:33:08.913 4 August: ISAKMP: (0): sending a packet IPv4 IKE.
* 4 August 09:33:18.913: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH...
* 09:33:18.913 4 August: ISAKMP (0): increment the count of errors on his, try 3 of 5: retransmit the phase 1
* 4 August 09:33:18.913: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH
* 4 August 09:33:18.913: ISAKMP: (0): 1.1.1.1 package sending 500 peer_port 500 (I) my_port AG_INIT_EXCH
* 09:33:18.913 4 August: ISAKMP: (0): sending a packet IPv4 IKE.
* 4 August 09:33:28.913: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH...
* 09:33:28.913 4 August: ISAKMP (0): increment the count of errors on his, try 4 out 5: retransmit the phase 1
* 4 August 09:33:28.913: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH
* 4 August 09:33:28.913: ISAKMP: (0): 1.1.1.1 package sending 500 peer_port 500 (I) my_port AG_INIT_EXCH
* 09:33:28.913 4 August: ISAKMP: (0): sending a packet IPv4 IKE.There is no DMVPN on the SAA. All that you have configured, is not compatible with the ASA or something another DMVPN then. At least debugging shows that there are some EzVPN involved.
The debug version, it seems that there is no communication on UDP/500 possible between devices. Maybe something is blocking who?
-
Cisco Asa 5505 and level 3 with remote access VPN switch
Today I had a new CISCO LAYER 3 switch... So here's my scenrio
Cisco Asa 5505
I have
Outside of the == 155.155.155.x
Inside = 192.168.7.1
Address POOL VPN = 10.10.10.1 - 10.10.10.20
3 layer switch configuration
VLAN 2
ip address of the interface = 192.168.1.1
VLAN 2
ip address of the interface = 192.168.2.1
VLAN 2
ip address of 192.168.3.1 = interface
VLAN 2
ip address of the interface = 192.168.4.1
VLAN 2
ip address of the interface = 192.168.5.1
IP Routing
So I want the customers of my remote access VPN to access all that these networks. So please can you give me a useful tip or a link to set up the rest of my trip
Thanks to you all
Al ready has responded
Sent by Cisco Support technique iPad App
-
Using a Cisco ASA 5505 to transfer applications PXE (WDS)
I have a Cisco ASA 5505 that uses approximately 5 CARDS for different networks. Currently, I use my ASA to route traffic as it is the only Cisco device I have able to the small amount of routing required by my network.
Keep separate things that I use 5 CARDS for different networks like outdoors, corp, Printers,workstations, serversand public. Each has a different subnet I keep separate to control all ACL through the firewall of the SAA. All (for example, DHCP with global scope) works very well except the WDS server.
My question is, now I have a new PC connected to the workstations LAN NETWORK card looking for my WDS server that is on the Server LAN. How can I get requests for all different NIC to flow to the servers LAN NIC?
Hello
If you require pass queries all other interfaces to the server DHCP behind "servers" interface?
Then, you need to configure DHCP Relay
Server dhcprelay
dhcprelay enable
dhcprelay enable
-Jouni
-
Using IKEv2 from Microsoft with Cisco ASA
Hello
I just want to confirm something, if I can put this issue to rest.
We have a Cisco ASA 5505 running OS 8.4
For remote access, we have the configuration of SSL VPN to include IPSec (IKEv2).
With the help of our AnyConnect client works. No problem.
The issue is on my Windows 7 computer when I place a remote access profile I choose IKEv2 (PPTP or L2TP/IPSec). However, this does not work.
It error to say that he "cannot find a matching policy. I'm assuming what he mean't he couldn't find any political IKE. I have added other policies of IKE, which has find a match, but ASA connects the barks by saying "IKE neogoiation fails in search of a certificate or a preshared key".
There is no option for inputing a pre-shared for IKEv2 on Windows 7 with its profile.
Therefore, I think that on the ASA 5505 IKEv2 is only used for remote access with the AnyConnect client (or the client AnyConnect Secure Mobility) and NOT with other clients like Microsoft IKEv2.
Is this really the case? Or can I use IKEv2 integrated with Windows 7 to access remotely the ASA 5505 enabled for IKEv2 for remote access (and not as a site-based virtual private network)? If so how did you get it to work. It is an empty topic of discussion on the Internet.
Thank you!
-rya
Hi Rya,
I don't think there are changes to this recently but ASA doesn't work with anyconnect with IKEv2.
I recently wrote about this in my blog
Frankly I did not follow developments of this features recently, so I might have missed something.
Marcin
-
Cisco ASA 5505 unable to access the remote network
Hello
I have a Cisco ASA 5505, with 50 basic license, which is connected directly to the Modem cable with a public IP address. I have configured and active VPN on the outside interface. When connect us, we connect well without error, but we are not able to access all the resources on the remote network.
ASA IOS version 8.2 (5)
Remote IP network: 10.0.0.0/24
VPN IP Pool: 192.168.102.10 - 25
I have attached the config: llc.txt
Please let me know if you have any questions.
Thank you!
Hello
Try adding NAT 0 because inside subnet--> subnet distance
NAT (inside) 0 access-list TEST
TEST access ip 10.0.0.0 scope list allow 255.255.255.0 192.168.102.10 255.255.255.224
HTH
MS
-
I can't boot on my Cisco ASA 5505
Hello;
I am facing a problem with my cisco ASA 5505 firewall. When I connect my cable to console the firewall to start setting firewall load and stop until the copyright. ICN can't access to the firewall to view the configuration. I start also with Rommon but I am facing the same problem. Does anyone have an idea of this problem and can help me?
Please, it's so urgencly!
Hello
What version of software is on the asa and the amount of memory is on the device?
Thank you
John
-
Renew the certificate of identity on Cisco ASA 5505, do I have to renew all user certificates?
n00b questions.
I have to renew my SSL certificate of identity soon on my Cisco ASA 5505. I'll have to renew all my certificates for client on their devices, so they can establish a vpn tunnel?
Hi dsartoros,
If you encounter a self signed (generated locally) identity certificate renewed, then you will need to download this certificate on the clients so that they can connect without getting "untrusted server certificate error".
If you renew a certificate issued by a 3rd party CA (sending of CSR to CA) and certificate, then you will not need to make any changes on the client as they already trust the certification authority that issues the certificate first root.
Kind regards
Dinesh MoudgilPS Please rate helpful messages.
-
Cisco ASA 5505 VPN passthrough
Hello
@home i'f installed a Cisco asa 5505 because the provider has the modem cable in transparent mode. So I have the public IP address to my firewall.
Also for the training because we have in the work of the asa. So I have no feeling with her.
but sometimes I have to build a VPN session to a server at work. But I do not get a connection to the server. If I remove the ASA 5505, then the connection to the server of work is great. But if to ASA 5505 is back in its place. It does not log VPN to the outside world.
Could someone point me in the right direction?
It is possible to create a connection out to the Cisco ASA5505 VPN.
Thanks in advance
Greetings
Palermo
Hi Palermo,
You do not have to mention the type of VPN connection, you use.
If the PPTP protocol then you need to inspect the traffic for the SAA allow again from 'outside '. Try the following:
! class-map inspection_default match default-inspection-traffic ! policy-map global_policy class inspection_default inspect pptp ! service-policy global_policy global !
see you soon,
SEB.
-
CISCO ASA 5505 no cisco VPN Client
Hello
I'm looking for after a firewall Cisco ASA 5505 and want to watch all the owners of it with remote access in but none of us have a support contract with Cisco.
Is it possible to set up a VPN client not as Microsoft built the client to connect to the ASA?
Thank you
Alamb200
Hello
Looking for a PPTP on ASA connection?
The following document provides the following:
ASA q support PPTP client?
A. number of the
But we can configure ASA to allow the PPTP connection:
I hope this helps.
Kind regards
Anisha
P.S.: Please mark this thread as answered if you feel that your request is answered. Note the useful messages.
-
How to configure ASDM Cisco ASA 5505
I have a Cisco ASA 5505 firewall, and currently it is a command-line firewall. I want to configure ASDM so that I can use it as a Web based GUI interface.
I don't really know what to do. Can someone help me please how I can configure ASDM on my firewall.
Kind regards
Naushad Khan
Hi Naushad,
First of all, must load the image ASSDM on SAA and then use the command:
ASDM image dosk0: / asdm645.bin (if the image name is asdm645.bin)
then:
Enable http server
http 10.0.0.0 255.0.0.0 inside (if your machine is 10.0.0.0 subnet behind inside the inetrafce)
Go to the machine, open a browser and type:
It will open the GUI.
Thank you
Varun
Please evaluate the useful messages.
Maybe you are looking for
-
How to save only a few forms and historical research
I want to only do Firefox back up my personal emails and never save anything else (if someone has used my computer and uses e-mail address for example).
-
Firefox thinks I want to download something when I just want to open a web page. URL of affected sites http://Forex-foryou.com/introduces/Xtreme-PIP-poacher
-
Linux installation (or other OS) will be empty guarantee?
It is mentioned that Toshiba does Windows support will be instaallation from another OS as Linus will void the warranty?
-
Kernel panic regular since the upgrade to El Capitan
Hello I recently installed the new RAM and SSD in my macbook 2009 mid pro with the intention to give a new breath of life for a year or two. Worked perfectly until I decided to upgrade to El Capitan. Since then, I get the regular kernel panics - seve
-
Hello everyone, I have been using MID-7654 for 1.5years as for now with the motion controller PCI-7358. I encountered several problems and I am now controlling 4 different actuators simultaneously. But today when I turned on the system, the motor con