Questions about the Satellite A200 and TV connection

Similar Questions

• A few questions about the Satellite A200 - 204 (PSAE6E)

  I recently bought a Toshiba model Satellite A200 - 204 (PSAE6E) bought the 05/12/2008, the garage.
  NATIONAL ALVAREZ (Al Khoudh, Oman),

  Sealed opening box, I realized that product had two questions, I immediately reported it to the dealer.
  (1) red spot on the LCD (Pixel damage)
  (2) LCD junk shows up after every 10-15 minutes of use.

  For the Point 1.*
  The Service Center authorized returned the noteback quote myself
  "The question of a white spot on the LCD is not the responsibility of the Department."

  For the point 2.
  The dealer has made installation of o/s for 2-3 hours of surveillance.
  Now ask to take me to authorized service center and keep for 2-3 days of surveillance.
  only then can the material be confirmed (as appropriate).

  However, I would like an honest of any opinion if this can be termed as "DEAD ON ARRIVAL" & can I request a replacement in these circumstances!
  Kind regards

  BILEL RAO

  Published by: ADMIN

  Hey Buddy

  As far as I know dead on arrival questions are always issues between business partners.
  So if something is wrong with your laptop, you could request a laptop replacement. You should ask your dealer to laptop.

  Now, I want to say something about your question;

  I found helpful article from Toshiba on the dead pixel problems:
  [What is the maximum number allowed and the type of fault of pixel your monitor LCD Toshiba can expose by 1 million pixels? | http://support.Toshiba-tro.de/KB0/TSB5400ZD0002R01.htm]

  Usually it is not big thing to do because there is a kind of tolerance of dead pixels.
  Only if the number of dead pixel is larger, then the number described in the document above the ASP will replace the screen.
  The best advice is to go back to the dealer and replace the notebook.

  On this second volume of Toshiba, you can find more information about the tolerance of dead pixel:
  [I have one or more bad pixels on my screen, I can fix? | http://support.Toshiba-tro.de/KB0/FAQ350079001NR01.htm]

  Good luck

• Question about the Satellite A200 bios password removal

  Hello.
  I own a Satellite A200 - 1 KB which has a password on startup and I would like to delete the password.
  I tried to get into the bios setup but I can't turn it off from there and I tried holding the ESC and hold left SHIFT to start but didn't work as well.

  If someone could help woul be great...

  Hello

  Unfortunately you won´t get here of secret advice on the deletion of bios passwords because the passwords were intended to protect a computer from unauthorized access. Thus, the password for the BIOS of your laptop is more often sunk that leads to the only solution:

  Contact an authorized service partner and let the button remove the password. But don't forget that you will be charged since the removal of the password of the BIOS is not covered by the warranty. Each manufacturer made this way, otherwise it would be easy to steal a machine, ask someone from a forum, and then use the stolen computer.

  You know what I mean? Here´s a link to find the closest available ASP in your country:

  http://EU.computers.Toshiba-Europe.com/cgi-bin/ToshibaCSG/download_whitepaper.jsp?service=EU&WHITEPAPER_ID=0 000000871

  Welcome and good luck

• Questions about the Satellite A200 display resolution

  I have a computer laptop satellite A200 PSAE0. I went down the operating system to windows xp. The resolution of my screen can become greater than 1280 x 800. Is - is this the highest resolution possible. I don't like somehow?

  Hello

  As far as I know, that this model of laptop with an Intel graphics chip arguably a resolution of 1440 x 900 px.
  I guess XP Intel graphic driver does not support a resolution higher as 1280x800px if aren't you able to choose higher as 1440 x 900 resolution.

  Therefore, in my opinion, you should try to install other compatible Intel graphics cards drivers to have a choice of 1440 x 900.
  But if the new graphics driver Xp will not allow the resolution of 1440 x 900, you must stay on 1280 x 800.

  I recommend looking at the Intel Web site and Toshiba to display compatible and taken drivers supported.

  Good bye

• Question about the Satellite L300 to TV connection

  Hi everyone, first of all this is my first post.

  Also I'm a bit geek o when it comes to computers etc., I can use one but im not a wizz tech kid as well as use of base of an im afraid.

  I have a Satellite L300 laptop.

  My question is, my laptop has no HDMI port, but it has a VGA port.
  I have a digital TV with many ports Inc. USB, VGA, HDMI etc.

  I am downloading movies and burn them on dvd, but it's very tedious, so I wonder if I connect the laptop to the tv to use the TV as a monitor screen? so, I can either watch the dvd on the tv, and gold to direct flows to the laptop and then on television.

  I connected a vga cable for the necessary ports between the TV and the pc, and although television confirms that a pc is connected, there is only a white screen? so I guess I can't connect in this way.

  It is not possible to connect using the usb ports? or of other ideas like if I may or may not connect to this laptop?

  Kind regards

  Bob

  Hi Bob

  What laptop has no HDMI port this is a bit complicated. In General, you should be able to use your TV as external monitor. When you connect your laptop with VGA cable to your TV and turn on this port to the TV use the FN + F5 key combination and desktop to TV switch.

  If your TV is correctly detected when you use FN + F5, you should see several options. Problem is that the VGA connection is for video only and you will not hear on your TV. You can transfer the sound, but you must separate the wires and connect the headphone jack of your laptop and openings of his TV or even receiver Hi-Fi if you a.

  It's a little complicated.

• RAM and GPU update questions about the Satellite A60 652

  Hello

  I have a question about my Satellite A60-62. I want to upgrade the RAM, but I do not know what kind of chip that I have to do and how that insert into the laptop.
  I also want to get a new card to my video graphics, I currently have "Radeon Mobility IGP 7000', is this possible, and the same questions again, what card do I need and how to I insert in the laptop..?

  Thanks for any help.

  Hello

  The works of A60 with PC2100 and PC2700 memory.
  The maximum is 1536 MB.
  Toshiba part numbers are:
  PC2700 256 MB PA3311U - 1 M 25
  PC2700 512 MB PA3312U - 1 M 51
  1024MO PC2700 PA3313U-1M1G

  The graphics card cannot normally be improved.

  Good bye

• A few questions about the Satellite A100 PSAANE

  Hi friends,

  I have a Toshiba Satellite A 100 - PSAANE with Vista Home Basic preinstalled in it.
  Now, I have a few questions... I mention below: -.

  (1) if I want to format my laptop, I need a CD to install for Vista Home basic... then I don't have this Toshiba CD when I bought the laptop. So how do? question: How can I format it?

  (2) can I change my Vista Home Basic to windows XP? I think it's much faster than this one. is it advisable?

  (3) I have a GB of RAM in the laptop. Increase the RAM? I think that my laptop has become to slow down. is it advisable?

  (4) and on my screen, everytime I try to change my profile screen to windows Classic view, my screen begins to blink. and after a while, the screen turns off. So I can't change that. I put the color scheme of windows vista only. What to do about that?

  Please help me friends. Thanks in advance.

  Kind regards
  Perkins

  Hello

  Here, a few questions about the number:

  (1) usually, you should get the Vista Toshiba Recovery DVD. If you didn t receive this DVD then you can order it here https://backupmedia.toshiba.eu/landing.aspx or you could install the disc of Microsoft Vista.

  (2) of course, you can do this. I think that Win XP drivers can be downloaded from the Toshiba driver page.

  (3) Yes, you can upgrade the RAM. For more information, see your manual or search on this forum for similar topics

  (4) maybe it s associated with the graphics driver. Check if you can update. I would recommend additional check if you are using the latest version of the BIOS

  Welcome them

• Questions about the Satellite A500 - 14 k

  Hello

  I'll buy a Toshiba Satellite A500 - 14 k, and I would like to know:
  -It has a keyboard backlight?
  -It has a "slot loading DVD player?
  -is its remote control really on format express card?

  I am French, and the French A500 series is perhaps different.

  I speak excellent English, excuse me ;)

  Good day.

  Is this laptop already on the market in France?
  I mean that if nobody here can give you a specific answer, please contact your local dealer or online store to pick up some information directly.

  Google all over the place. I'm sure you can find some dealer who can help you.
  You are right about the different models and I think also all A500 will not be the same in all European countries. Please also note that it's first A500 series on the market and I think also for the French market, it can be changed in the future. It is possible that in a few months, you will be able to find more different models in France.

  In my country, Satellite A500 is not yet on the market. :(

• Question about the laptop battery and satellite L510

  I have a Toshiba Satellite L510 and find the battery moves a bit - like 2mm so be it.
  It is on the edge of the laptop, I suppose, but I was wondering if there should be no movement at all?

  Hello

  On my two laptops from Toshiba battery cannot be moved, but the battery is locked and cannot be moved or deleted.
  Your laptop satellite battery is too locked?

  By the way: when you use the notebook on the desk, this movement is irrelevant and cannot have a negative influence on the power supply for computer laptop battery s.

• A few quick questions about the Satellite P300 - 18 M

  Hello

  I am about to order a Satellite P300 - 18 M and have just a few questions about this:

  (Although these may apply for other similar Satellite/Equium P300.)

  Is the touchpad made by / to use the Alps or Synaptics driver?

  It has the Wireless N network card, is the map made by Intel or Realtec?

  And also, someone has experience with face recognition software to connect?

  If so, does it take a lot of time to initalise?

  Thanks in advance,
  Jack

  Hello

  The P300 - 18M belongs to the PSPCCE series.
  It uses the two touchpad drivers. Synaptics & Alps Electric
  There is an Intel 802.11agn minicards WLan installed

  The face recognition is a nice tool but local to be illuminated and you must take your face the right of the post sometimes it of not very easy

  But if you face is recognized correctly that the connection should work properly

  See you soon

• A few questions on the Satellite A200-1BJ

  Dear Sir.

  A couple of days, I bought laptop Toshiba Satellite A200-1BJ of Jarir Book Store, Al-Khobar, Saudi Arabia.
  The system configuration is provided by the company.
  Operating system: Windows Vista editions Home Premium
  300 hard drive space is divided into two partitions:
  C - Vista with Go 138
  D data disk seen 139 GK

  When buying the laptop, I had only the recovery CD and there is no Drivers CD. Three years agao, at the time of buying laptop toshiba, I got the drivers CD as well with the recovery CD. Why the driver CD does not come in the current edition of the laptop.
  I need to install a software application which requires about 200 GB of space. In this regard, I have the following questions for which I want explanation from you to guide me to take the appropriate action.

  (a) I want to create a new 50 GB partition using the free space on the C drive. How can I do this? If possible, so I can install my application software by merging 50 GB with the D drive space.

  (b) can I change the configuration of HARD disk space by installing the new copy of windows vista operating system. During the installation of the operating system, it will ask for the disk partition in this case, I'll format the C drive current and have a new partition of C (78 GB) and D (190 GB). Is this possible.

  (c) If b is possible, so how do I install all drivers in the system currently installed with, since Toshiba Co. don't did not provide me with the driver CD. How

  Can I get the drivers CD. Do I have to load all the drivers of webside and create a DVD of the same thing?
  Waiting for your response, which will allow me to take the appropriate decision.
  Thanks in advance.
  Kind regards.
  N. Rama Krishna Pai

  > Three years ago, at the time of buying laptop Toshiba, I got the drivers CD as well with the recovery CD. Why the driver CD does not come in the current edition of the laptop.

  I put t know exactly why Toshiba has decided to only provide the recovery CD and not the driver CD with the laptop, but all the drivers that are preinstalled on the laptop are on the Toshiba driver page. Given that all computer users have access to the internet, it should t be a problem with the driver download!
  Also the restore CD contains the entire image of Toshiba with all the pre-installed driver, tools and utilities.

  > I want to create a new 50 GB partition using the free space on the C drive. How can I do this?
  You can do it in Vista disk management.
  You can reduce the C partition and on free space, you can activate a partition of second or third.

  > Can I change the configuration of HARD disk space by installing the new copy of the windows vista operating system?
  To my knowledge, this is not possible using the Toshiba Vista recovery CD.
  But check the proposal above!

  > If b is possible, so how do I install all drivers in the system currently installed with, as Toshiba not did not provide me with the driver CD.
  B is not possible, but as already mentioned, the drivers are on the Toshiba page

  > Can I get the drivers CD. Do I have to load all the drivers from the website and create a DVD of the same thing?
  This CD can be obtained, because it does not exist. Download driver page.

• On the Satellite A200-1CR wireless connection is not working properly

  Hello

  I have a problem with my wireless connection. In spite of I stay close to my router I can't access the Internet.
  If I have the connection, it is the level of 1 to 3 (5 is best).
  I have the same problem with "hot spot". I can't access the Internet or use only messenger, can't surf the Internet, check my emails, etc..
  Another person do not have this problem in the same places. They can access the Internet. What's wrong? Can you help me?
  I have a Satellite A200-1CR.

  Piotr

  Hello

  For most Wlan issues are related to problems of compatibility between the wireless network card and the Wlan router.
  Sometimes the Wlan driver allows to obtain the best performance.
  So, try to update the WLan driver first. Maybe it helps.

  Good luck

• Question about the Satellite C50D of charge

  Hello

  I have a problem with the battery on my Toshiba laptop. I connect and it says "charge (100%). ", but as soon as I disconnect the battery supply cable down exactly 50%. I don't know how much time he did this, but it's very frustrating not being able to have all the power (on the long trips etc.). I tried the high performance and energy saving mode.

  I tried to remove the battery and turn on/off the laptop and recharge overnight once it says 100%. I've looked everywhere and nobody seems to have this problem and its ruining the heck out of me.

  Bought: December 2013
  Running: Windows 8.1

  Thanks in advance.

  Try to use the laptop until the battery is completely empty and load it again at 100%.
  Check please if this will change anything. If this isn't the case, I recommend you contact the nearest Toshiba or your local dealer services provider.

  I ve heard about problem when battery shows 100% of load as long as the adapter is connected, but he can´t to keep the load once the adapter is unplugged. In this case the battery must be replaced.

  Contact service, explain the situation and follow the instructions given by the authorized service provider.

• See questions about the Satellite A205-S5859

  I would like to know the following:

  1. is there a problem with the speakers of this first use. The volume deteriorates. You will need to set to 100.

  2. can I put the car in a dedicated video video?

  3. What is the maximum memory for this model? Where is the memory chip?

  One of my friends has a laptop A200. It s not A205 but very similar. The A205 is designed for the American market and the A200 to the European market.

  So finally, I can give you some suggestions on the issue:

  (1) any volume questions are not known for me everything works ok.

  (2) No, upgrading the graphics card is definitely not possible

  (3) I guess you'll find this info in the user manual. Did you check that?
  But I think that there is a possibility for an upgrade to 4 GB of RAM. But I do not recommend upgrading the RAM to 4 GB due to the limitation of the 32-bit operating system. All the 32-bit OS s can manage 3.2 GB RAM max.
  Finally, the position of the slots memory; I think that it s at the bottom of the unit.

  See you soon

• Question about the composition settings and make

  I looked for an answer to my question, but had to ask at resort, sorry, it's pretty basic, but a direct response is needed I think.

  I imported a project in Premiere pro with two layers of still images with movement and applied effects. I work for a few weeks now, with variations on these pictures and had many number of exports of EI through the render queue.

  After you import the compositions of first CC my starting point; composition and other settings of composition parameters are all resolved HDTV 1080 25 but the set resolution in which I unfortunately now has, is defined as 'Half' (960 * 540)... New compositions also sets the default resolution somehow half...

  My question is about my previous exports and subsequently.  Together of the composition to "Half" resolution affect the quality of my compositions exported using the render module? So far, all my renders are 1080 p by default and no 960 * 540. These have been uprezed to 1080 of 960? ... - I have not changed any setting on the resolution in the rendering module - they all came out 1080 after.

  Thank you

  Together of the composition to "Half" resolution affect the quality of my compositions exported using the render module?

  N ° except if you change the settings of default rendering, which is "Best settings" in "current Configuration".