Reinstall Vista and trying to connect to my local network, he asks me "security key or password"?

Similar Questions

• Why if a system is xp and one system is windows 7 and the two connected to the local network, but file-sharing does not work

  a system is xp, another system is windows 7 basic and both connected to the local network, after you set up shared drive, mowing arrives not

  Hi Abhay,

  I suggest disable you the password protected sharing and check if it helps.

  Networking of computers running different versions of Windows

  Note: Follow the steps in the section "to enable sharing protected by password in Windows 7" and turn off password protected sharing.

• Satellite L500 - no possibility to connect to the local network

  Hello

  I'm new to these forums so please accept my apologies if I don't use the terminology correct tech.

  I have a Toshiba L500 laptop satellite. It of ok, but had to make the hard drive replaced recently (under warranty) as she died. I had been using a wireless network before I had to have the drive replaced and now trying to connect to a local network using a cable, but there is no device?

  Now, I don't know when this became a question - before or after replacing the hard drive. Not only has he failed to drive hard, but has so the speakers, so I wonder if the LAN device is just another thing that has failed.

  I understand that there are two components to the unit - the hardware and software. I learned that the material may have failed.

  Does anyone know how to get back the unit so that I can plug my computer on a local network and internet access? No, the device isn't in the network adapters. I don't know how to get it back.

  > I have the replaced disk and now I'm trying to connect to a local network using a cable, but there is no device?
  Have you tried reinstalling the driver LAN?

  Remember that the network driver is installed correctly you should check this in the device-> network cards Manager.
  In this category the LAN card and wireless network card required!

  If you're going to see some yellow exclamation points, so this means that a driver is missing or is not working properly and this means that you must remove/uninstall the driver, and after new restarts, the driver needs to be installed once more

  Please check this!

• A cable is not plugged into the network adapter 'connection to the Local network.

  Hi, I am using a Dell Inspiron E1505... OS: Vista... 32 bit... IE 9... I still use dial-up "Conexant HDA D110 MDC V.92 Modem" connection connected to the internet without any problem... the problem is when I asked someone to download a program "MS Office Home Student & 2010"(acheté le logiciel àle staples)... the person downloading the program via an Ethernet connection on my laptop... "." I never use the Ethernet connection to connect to the internet... Open to the top of my "Network connections" window and noticed my 'connection to the local network' has a red X and says "network cable unplugged"....." "" Broadcom 440 x 10/100 integrated controller. My toolbar in the bottom right of the screen displays an icon of two monitors with a red x as... I have made several attempts to fix using the "Microsoft fix - it Center... didn't help me..." also "diagnose and repair" on my laptop... no positive results... In the window "Network & sharing" "also shows a red X... Please advise... Best regards, John

  Hello

  Reading between the lines a bit here, it is my understanding...

  1. Never use Ethernet, probably because you don't have broadband for some reason any?
  2. Due to the size of the download, you asked someone else to do it with no broadband?
  3. As a result, which is two screens with a red X icon, but never used to be there?

  This icon with the red X is only informative. If you do not use Ethernet then you won't have connected cable, which means that the information you see on "network cable is unplugged" is correct. If you don't like this icon, you can hide...

  • Right-click on an empty part of the taskbar, and then click Properties
  • Click the Notification area
  • You will see a check box for the network, there uncheck and then click OK to hide the icon
  • Reverse this process, if you want to display the icon

  Or is your problem you can connect is no longer with dial upward? If this is the case...

  • Click Start, type inetcpl.cpl and press enter
  • Click the Connections tab
  • 'Never make a connection' values? If this is the case, always select "default connection" (or "Number using whenever a network connection is not present")
  • Click OK

  Tricky

• I have windows vista Enterprise edition and trying to connect to a PPTP VPN, I get an error 691.

  I have windows vista Enterprise edition and trying to connect to a PPTP VPN, I get an error 691 name of user and password are fine, I can connect to the VPN on XP without problem.

  original title: VPN Error 691

  I was able to find a solution by the way that the domain has been configured. I was adding the complete domain name and extension (i.e. domain.local). The .local was me screwing up. I edited the domain field to only reflect the domain name without any extensions. One that I did this it worked like a charm. I have been using a VPN PPTP on a computer Server 2003 domain mixed with 2000 and 2003 domain controllers and Windows 7 Pro laptop computers. Hope this helps someone.

• WIFI disabled on windows vista and cannot wireless connect to the net

  WIFI disabled on windows vista and cannot wireless connect to the net, but bluetooth wireless Wi - Fi and fine switch is activated. Have a problem with ISATAP #5 who is incapable of solving that can be bound.

  All of a sudden I lost my internet connection wireless and I am unable to return.  May be because recent windows update.  Error messages on the wireless assistant say WLAN offshore or disabled.  I have tried every fix.

  In device Manager (under network adapters) shows also that MS ISATAP disabled with "Windows cannot load driver (Code 31).  When I try to update the driver, "Best driver already installed" appears.

  Is there a way to FIX?

  http://support.Microsoft.com/kb/932520

  Read the above re ignore this error message.

  Go to the website of the manufacturer of your computer/laptop > drivers and downloads Section > key in your model number > look for the latest Vista drivers > download/install them.

  See you soon.

  Mick Murphy - Microsoft partner

• I have problems wireless on my Acer laptop which has Windows Vista. I am able to connect to my school of university network and used to connect to my home network.

  original title: Wireless on the Fritz

  I have problems wireless on my Acer laptop which has Windows Vista.  I am able to connect to my school of university network and used to connect to my home network (both are networks limited requiring a password or log in).  However, last week my computer stopped connecting to my home network (no one else has this problem with the home network).  I tried to fix the problem, but my computer says that "Wireless association failed because Windows did not receive response from the access point or wireless router."  That said also thatthe connection "(my wireless network)" has been cancelled.  This is perhaps due to a timeout or user action. »

  The only different thing I did last week was click option at my University 'connect long-term' instead of 'connect short term' to their wireless network.  Maybe who has messed up my settings?  That's what my University said of his record long term: "students, faculty and staff also have an option to easily record their computer (or other wireless devices), so that it is not necessary to authenticate each day they connect from the network wireless campus, to resources outside the University.»  However, these settings are saved on their network (I can access it online from another computer), so I think it is unlikely that he messed up my settings.

  I don't really know what the problem is.  Any ideas as to what I can do?  I don't want to reset my computer everything.

  Thank you!

  Hello

  You can view these methods:

  Method 1:

  I suggest you to disable any program of security on your computer and check if it solves the problem.

  After reviewing the question you must reactivate the security on your computer program.
  Note: Run the computer without antivirus software or firewall is a potential threat to the computer; Be sure to activate security software after completing the troubleshooting steps and after identifying the problem.
  Method 2:
  I suggest also allows you to check in SafeMode with network.
  http://Windows.Microsoft.com/en-us/Windows-Vista/advanced-startup-options-including-safe-mode
  Method 3:
  I also suggest you to check the settings of the router firewall.

• I have an acer aspire 5920 on vista and can't connect any printer to it... error message 0 x 00000002 arrives

  I have an acer aspire 5920 on vista and can't connect any printer to it... error message 0 x 00000002 comes up... all clues?

  Hello

  1 are there any changes or updates made on the computer before the show?

  2. you try to add a network printer?

  3. What is the full and exact error message?

  4. when exactly you get the error message?

  5. What is the number of brand and model of the printer you are trying to connect?

  Method 1:

  I suggest you check out the link and try sharing the printer:

  Share a printer

  http://Windows.Microsoft.com/en-us/Windows-Vista/share-a-printer

  See also:

  Network printer problems

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-network-printer-problems

  Method 2:

  Check out the links and check if that helps:

  File and printer sharing: frequently asked questions

  http://Windows.Microsoft.com/en-us/Windows-Vista/file-and-printer-sharing-frequently-asked-questions

  Troubleshoot file and printer sharing

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-file-and-printer-sharing

• After reinstalling vista and get the updates, I've "lost" more than 10 GB on my hard drive

  can anyone help? After reinstalling vista and by then setting automatic updates, I find after the download and installation of updates that I "lost" more than 10 GB on my drive hard, why is that?

  Updates must be stored somewhere, and installed somewhere 10 GIG is in the normal range.  Did you do a disk cleanup?

  have you saved or set a restore point?  It has been a decade since I used Vista, but I think that any time you install something made Vista a restore point.

• What I would do, my computer has so many unwanted programs, is to reinstall Vista and not all HP programs that I don't want.

  What I would do, my computer has so many unwanted programs, is to reinstall Vista and not all HP programs that I don't want.  It seems to make the computer too slow.  I don't have a Vista disc, only the recovery CD I did in the beginning. Can I recover and just reinstall Vista, or should I get back it?
  Thank you
  Bill

  original title: recovery

  If your "Vista recovery disc" is provided by the manufacturer of your computer, be it Dell, Gateway, Hewlett-Packard, etc... Then chances are he's doing a thing. Completely format your hard drive and restores your computer to the day you brought it home. It's a major nuisance for many people these days, as if you have an error and Windows says 'Please insert the Vista CD to fix it Windows' well, you do not HAVE the CD to correct the error. Your only option is a complete erasure of all data.

  So, my advice is to avoid ever NEED to use the recovery CD, and if you don't... hope you have backups of your important data (which is another thing, backup your important data often!).

• I had to reinstall Vista and now my microphone does not work.

  I fully reinstalled Vista and my sound was working fine, but my microphone was not.  I looked for answers on the forum, and one person said the audio driver to uninstall and reinstall.  I uninstalled and now I can't figure out how to reinstall!  Help, please.

  It comes with Vista, upgrade install and activate Forum.

  http://social.answers.Microsoft.com/forums/en-us/vistahardware/threads

  They will help you with your question in Vista Hardware and drivers Forum above.

  See you soon.

  Mick Murphy - Microsoft partner

• No Internet access, the 'Connect to the Local network' and 'Wireless network connection' are "Local only".

  I'm portable computer maintenance of the customer, a Toshiba Satellite L305-S5885, under Vista Home Premium x 86 SP2, with infections by malicious software and internet connection problems. I have managed to get rid of all of its 251 infections and I am now addressing the connectivity problem. I'm unable to achieve on its ethernet or a wireless connection to Internet. The two network status of connections 'Unidentified network', and also ' access: Local only ' all other machines hooked up to my router via CAT5e and some via 802.11 g/n, have excellent speeds with internet connectivity, so I know that the problem is limited to his machine. I tried the following:

  Deactivation and reactivation of these two connections: FAIL.

  "Diagnose and repair" on the two connections: FAIL.

  Under dynamic I.P. type to static/static to the dynamic: FAIL.

  Uninstalled all network via Device Manager devices, then restart: FAIL.

  Manually uninstalled all the drivers and utility and installed the latest versions: FAIL

  The command ipconfig/all text follows:

  ----------------------------------------------
  Microsoft Windows [Version 6.0.6002]
  Copyright (c) 2006 Microsoft Corporation. All rights reserved.

  C:\Users\Brooklyn's>ipconfig/all

  Windows IP configuration

  Name of the host...: Brooklyns-PC
  Primary Dns suffix...:
  Node... type: broadcast
  Active... IP routing: No.
  Active... proxy WINS: No.

  Wireless network connection Wireless LAN adapter:

  The connection-specific DNS suffix. :
  ... Description: Intel (r) Wireless WiFi Link 4965AGN
  Physical address.... : 00-21-5C-31-87-95
  DHCP active...: Yes
  Autoconfiguration enabled...: Yes
  Autoconfiguration IPv4 address. . : 169.254.174.235 (Preferred)
  ... Subnet mask: 255.255.0.0.
  ... Default gateway. :
  NetBIOS over TCP/IP...: enabled

  Ethernet connection to the Local network card:

  The connection-specific DNS suffix. :
  Description...: Realtek RTL8102E Family PCI - E Fast Ethern
  and NIC (NDIS 6.0)
  Physical address.... : 00-1E-33-4E-2E-F7
  DHCP active...: Yes
  Autoconfiguration enabled...: Yes
  Autoconfiguration IPv4 address. . : 169.254.74.29 (Preferred)
  ... Subnet mask: 255.255.0.0.
  ... Default gateway. :
  NetBIOS over TCP/IP...: enabled

  Card tunnel Local Area Connection * 6:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: isatap. {C41651CC-0B3D-411D-8187-745214 C 69}
  B4B}
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes

  Card tunnel Local Area Connection * 11:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: isatap. {816357D 3-D 8-494C-AA09-F622AE861 44}
  0FA}
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes

  Card tunnel Local Area Connection * 14:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: Teredo Tunneling Pseudo-Interface
  Physical address.... : 02-00-54-55-4E-01
  DHCP active...: No.
  Autoconfiguration enabled...: Yes

  C:\Users\Brooklyn's >
  --------------------------------------------------

  Guys, I'm really hitting my head against the wall on this one, and I would be VERY happy for any help through this. Thank you!

  I thought about it, there was a corrupted installation of Norton 360, the origin of the problem. I've used the Norton removal tool and voila! Internet! Thank you.

• Connected to the local network, but can not use internet

  I recently had problems with access to the internet after reinstalling windows 7. Before the reinstall worked very well.

  I can connect to the local network without problem, and it shows that the internet is connected. Yet I can not access the internet. When I disconnect and reconnect, I get a few seconds of internet work before it stops working.

  When a diagnosis in the network and sharing Center, I get the error "default gateway is not available" and occasionally "the connection between your access point, etc. and internet is broken"

  Other computers and devices using the network are working properly, although there was a 'competitor IP address' error on another pc, which, after a reconnection, solved itself.

  I use an edimax 802.11n wireless card and a D-link router

  I tried several things to make it work again, but without result. Any help would be greatly appreciated

  disable TCP/IPv6 had no effect.

  I think I can have fixed me, I installed the driver microsoft before the reinstall instead of the driver edimax and internet suddenly started working.

  Thanks for the help of yor

• Re: Satellite Pro A40 - connection to the local network

  Hello

  My names Andy and not bieng a total beginner computer, I tried to install all the drivers for my laptop model a SPA40 old fathers PSA45E-001VM-EN. (European model I think) everything looks ok, except that I can't get the ETHERNET driver.

  When I go into the Device Manager there is NO controller network displayed in the list and there is a yellow exclamation mark against two controllers ethernet ib the OTHER DEVICES tab looking here, I downloaded the atheros wlan xp file - 7704062.zip, broadcom wlan xp - installed 5604835.ziplan20070912134727.zip and nothing changes, we used to be able to go on the net and with the wifi card in the pci slot wireless go so I know its capable I think it's just the order of drivers and the drivers themselves,

  Then someone can point me in the right direction before as I have send myself crazy with this...

  You can

  regards and thanks in advance

  Andy

  Hey,.

  The drivers that you downloaded are WLAN Card and has nothing to do with the connection to the local network (Ethernet) normal

  I think you should check the Web from Toshiba site to download the latest LAN driver. You can find the drivers for Satellite Pro A40 in * archives *.
  ttp://EU.computers.Toshiba-Europe.com/innovation/download_drivers_bios.jsp h

• HP OfficeJet Pro 8600: HP OfficeJet Pro 8600, connected to the local network but does not print a printer on the same LAN

  HP OfficeJet Pro 8600, connected to the local network but cannot print printer on the same local network.

  Work tried fixing it but all attempts fail.

  Firewall disabled.

  Printer recognizes the router's LAN.

  Was also pointed out that the port does not communicate, can not remove it; Cannot add another...

  Printer does not print.

  How can I fix?

  Hi @AnnisMonadjem,

  Welcome to the Forums of HP Support!

  I understand that you are unable to print to your printer HP Officejet Pro 8600. I'd be happy to help you and don't forget to come back to this thread and check "Accept as Solution", if I have successfully helped solve you the problem. If you want to say 'Thank you' to my effort to help, click on the "thumbs up" to give me a Kudos.

  When you say 'LAN', are you referring to the network or you try to share the printer on the network?

  How is the printer connected? (Ethernet/WiFi)

  If you have noticed that the port is causing problems, please download and run the print and Scan doctor, it will be probably diagnose and fix the problem you are experiencing.

  What were the results when you ran the Print and Scan Doctor? (she print or scan, error messages)

  HP has several Officejet Pro 8600 series.

  What is the name and the product number of your printer? How can I find my model number or product number?

  • Update the firmware of the printer.
  • Don't hide the SSID (network name).
  • What type of encryption are you helping? HP recommends WPA and WPA2.
  • You have a double router broadband? Make sure that the two groups were not the same network name.

  If the problem persists, you may encounter an IP address conflict. It's a good idea to assign the printer a static IP address outside your DHCP range. For example, some routers default DHCP is located between 192.168.0.100 to 192.168.0.200. So, I would use 192.168.0.232.

  To assign the static IP address, use the following steps as a guide.

  • Print a Page of Network Configuration menu of the printer front panel. Note the IP printer. IPV4 address
  • Type the IP address in the browser to bring up the SAP.
  • Choose the network tab, then wireless on the left side, and then select the IPv4 tab.
  • Select Manual IP.
  • Enter your IP address manual (192.168.0.232)
  • Enter 255.255.255.0 for the subnet mask, except if it is different.
  • Enter the IP address of your router that sits on the Network Configuration Page) for the default gateway.
  • Please, click on manual DNS server. For the preferred DNS Server Manual please enter 8.8.8.8 and the Alternate DNS Server Manual, please enter 8.8.4.4.
  • Click on apply.
  • Restart the router, the printer and the computer.
  • Test printing and scanning.

  If the problem persists, download and run this patch rollup: resolving printing issues in Windows 7 and Windows Server 2008 R2

  • Try printing and scanning.

  In addition, if you are still having problems try the steps in this guide, HP printers - "offline" Status Message printer (Windows 7).

  Continue on, if the problem persists.

  Important!   Delete the temporary files and folders by using the disk cleanup utility

  1. Open the disk cleanup utility: