Remove image of Cisco SF 300-24 flash problem

Similar Questions

• I would like to know to remove images from an sd card.

  SD card

  I would like to know to remove images from an sd card

  Put in a USB (SD card reader) adapter and remove them as you would on a flash drive.

• How to connect Cisco SG-300-10 L3 switch selector mode in Mode of L2 SG-300-20

  Ladies and gentlemen, please forgive me if you find my question too basic. But, I would really appreciate your help. I have two Cisco switches (SG-300-10 and SG-300-20) and I am struggling to connect with each other.

  Requirements: Switch Cisco SG-300-10 which is in needs of L3 mode to send the traffic of VLAN tagged to the switch Cisco SG-300-20, which is the mode of L2

  What I've done so now

  1 Cisco SG-300-10 (Mode L3) to the router directly connected and configured IP addresses, 192.168.0.21. The GVRP is configured for Port 5. Created the VLAN 1000 with interface IP (192.168.100.1) and configured the Port 5 trunk mode (1U, 1000 t)

  2 connected Cisco SG-300-20 (L2 Mode) to the router and set up the IP address management, 192.168.0.22. The GVRP is configured for Port 5. 1000 of VLANS created and configured the Port 5 trunk mode (1U, 1000 t)

  What does not work

  I can't access the address of management of the L2 (192.168.0.22) switch. Note that the L2 switch only on the uplink, which is to the L3 switch. Since the Port 5 also receives no marked traffic of VLAN1 (192.168.1.1), I'm assuming that he would receive the network management of VLAN1.

  Other Observations

  When I connect the cable between the two switches Port5, I expect to exchange information of VLAN, by documentation. But the lights flash at all.

  I tried other things

  I tried to connect Port 2 (1U) L3 Switch switch 2 L3 Port (1U). Yet, I can't access to the management of the L2 switch port. However, when I connect 2-Port L3 switch to my laptop, I get an IP address. That tells me that I have to solve the problem of management network pair before the switches.

  Hi Späti,

  I think the confusion is the use of the address IP address to you and how you manage your computer.

  VLAN 1 = 192.168.1.1

  VLAN 1000 = 192.168.0.21

  How I read that you connect layer 2 VLAN 1 on 192.168.0.21 switch to layer 3 of the same VLAN 1 interface to 192.168.1.1. It's confusing.

  So first thing to do is this - change layer 2 switch network 192.168.1.x IP and confirm management works on VLAN 1.

  If you want to layer 2 switch works on VLAN 1000, then you need to change the default VLAN 1000, then you can configure your uplink either as the way which you have 1u, 1000 t, or you can use 1000u.

  Your management VLAN on the layer 2 switch is VLAN 1 still unless you changed it (which did you not?)

  A next important thing for the layer 2 switch is going to be the default gateway. The switch of level 3, you need to specify the address IP of the VLAN 1000, which I think you did to 192.168.0.21/24. This 192.168.0.21 must be the default gateway for the layer 2 switch.

  Finally, the computer you connect to layer 3 switch, what that either VLAN that you choose to connect to (1 unidentified), you need to set the IP and default gateway appropriate. So if you're going to VLAN 1 then your computer is 192.168.1.x with gateway 192.168.1.1

  And for the comment extra, GVRP is a horrible Protocol and very pitiful, I don't recommend to use.

• Cisco SG-300 52 QoS default DSCP to queue mapping

  I am setting up QoS (Advanced mode) switch Cisco SG - 300 52.

  I decided to go with DSCP to manage the priority of the packet. While the implementation I found a configuration page (see the attachment for screenshot) where it is possible to map DSCP values in a particular queue. I did not quite understand the default settings of this mapping.

  The assignment of the queue increases from 1 to 4 for 0 to 47 DSCP values. Well, the 48-63 DSCP values were assigned #3 queue. In this way the package with value DSCP 56 will have lower priority than package with value DSCP 40. It makes no sense to me. Should not increase the priority (and thus the queue) that the increase of DSCP values?

  Why the 48-63 DSCP values were assigned #3 as default file?

  DSCP - default.png

  

  I think that the answer to this direct request found in RFC 2475

  Here is the link to the RFC.

  https://www.ietf.org/RFC/rfc2475.txt

  I think the info you're looking for are under classifiers. I deny not that under any normal logic to increment just respectively. For some reason, it was the standard/normal values agreed.

  I don't know with the first 6 bits in binary has something to do with the decimal value (expressed in a number which is not binary DSCP).  Also, I think it has to do with how the cycle increments of 8 values.

  By RFC 791, here are the priority values.

  https://www.ietf.org/RFC/RFC791.txt

  Example:

  000 = Best Effort

  001 = priority

  010 = immediate

  011 = audio/video.

  100 = flash on Ride

• HOW TO REMOVE IMAGES FROM MY PHOTOSTREAM ON APPLE TV4 PHOTOS

  the pictures on Apple tv4, there is a window "my photo gallery.

  It is to show the images that I deleted some photos on my other IOS devices & on my mac pro

  How can I delete images or all 'my photostream window' on apple tv 4?

  I have not found a way to remove images of photo stream of the Apple TV 4 yet, maybe they it will introduce in a later version. However deleted photos from mac or any other device must sync to Apple TV, it may need to update. Try to activate the photo stream and turn it back on (settings > accounts > iCloud)

• How to remove image files i've got duplicates when it says I can't do it because the file is open in another program? What does that mean?

  How to remove image files i've got duplicates when it says I can't do that because the folder is open in another program? What does that mean?

  Hello

  • What version of Windows are you using?
  • What were the changes made before the problem occurred?
  
  Follow the steps in this given link and check if that helps.

  Method 1: check out the link below and follow the steps

  Access the link for more information about the error you receive below:

  Why can't I delete a file or a folder?

  http://Windows.Microsoft.com/en-us/Windows7/why-cant-I-delete-a-file-or-folder

  Method 2: you can also try to remove the file getting mode without failure.

  Access the link below to learn more about Safe Mode:

  Start your computer in Mode safe:

  http://Windows.Microsoft.com/en-us/Windows7/start-your-computer-in-safe-mode
  Method 3:
  Once you face this problem you can check in Manager tasks if there is an executed program attached to it.

  a. right-click on the taskbar and click Task Manager.
  b. in the Windows Task Manager window, go to 'Process' and check if there is no program associated with those files.

  
   

• How to console Access of Cisco SG 300 - 28 P

  Hi Experts,

  We have just a cisco SG 300 - 28 P switch. We tried the initial installation according to the manual, but we are not able access the switch to configure. Suite of methods we tried:

  1. connected a lan cable from a computer to an ethernet port on the switch, statically assigned 192.168.1.100 IP address to the computer and attempted to access switch with default IP address: http://192.168.1.254

  2 connected the serial cable that was awarded with the switch on a machine a I tried to access through terminal tera. I have seen cables serial that has RS 32 port to be connected to the machine and RJ45 adapter to the switch console port. But for this switch, it is opposite, IE the RS 32 port switch and RJ 45/machine.

  It would be great if we can access the switch through the console port. Please help me on this.

  Kind regards

  Martin

  Hello

  The correct console cable type is null-modem cable DB9 R232 has "Female DB9" connectors at both ends of the cable.

  Kay Lee Yiu

  Concentrix at Cisco

  .:|:.:|:. CISCO | Kay Lee Yiu | Pre-sales SMB | [email protected] / * / | Phone + 1 (855) 354-7776

  

• Configure the VLAN voice and data in CISCO SF 300 8 P

  I have a couple of Cisco SF 300 8 P and P 24 switches. I have voice and data VLANS configured as:

  Data VLAN: default 145.17.59.0/24

  Voice VLANS: VLAN 20 172.22.20.0/24

  I have different DHCP servers regarding the data VLAN, we have a physical server that is configured for 145.17.59 * extended IP and Voice VLAN DHCP Server is configured as a router gateway with option 150.

  This configuration works very well with other cisco 2960 switches and 3750 etc. except CISCO SF 300 8 P and 24 p. I tried to set up the voice and data VLAN in these CISCO switches so that phone CISCO (model 6941) should get IP of the VLAN voice and PC should get the IP address of the DHCP server on the data VLAN. I tried several techniques such as LLDP, Port-to-VLAN Config etc.

  Can anyone please guide me / help on this.

  Kind regards
  A K.M.Sayeed

  Hi A.K.M., with Cisco phones you should be able to define simply automatic voice VLAN to be VLAN20.

  ID of the vlan 20 voices

  You must ensure CDP or LLDP is enabled as well. I would check in the web GUI. DHCP for phones can come from a DHCP server on a port access VLAN20 switch, or you can use dhcp for assistance to redirect DHCP server elsewhere.

  If you prefer or you have problems with the CDP or LLDP, you can also program the ports as trunks and add the tag VLAN 20 for them.  In this scenario, you need to ensure inter - vlan routing works and phones that download the file config with corrrect VLAN config.

  These switches do not run ios, so they are similar, but different from the catalyst switches that you mentioned.

  -remember messages useful rate.

• Problems of implementation of VLANS on Cisco SG 300-28 comments

  Hello

  I'm mainly curious if the configuration that I explained below is actually possible, and if so how do I implement. I know that this isn't the easiest configuration and I need to put in place without buying any equipment more if possible.

  I have a SG Cisco 300-28 with three Setup VLAN

  Vlan1 (company) - 192.168.10.0 - switch IP 192.168.10.254

  VLAN2 (VOIP) - 192.168.20.0 - switch IP - 192.168.20.1

  VLAN3 (guest) - 192.168.30.0 - switch IP - 192.168.30.1

  Default gateway is 192.168.10.1 (Netgear router)

  I have a wireless network setup (Netgear WMS and WAP 2) configured with TWO VIRTUAL (1 and 3) networks. They enter ports on the Cisco SG 300 - 28 which are marked on the two VIRTUAL networks. The wireless carriers has worked well, but the guest network is not reout on the Internet.

  After some troubleshooting I realized that the reason wasn't the guest was because there was no path routing of the internet to the router.

  The router I have is not really ideal, it is a Netgear DGN2200, but I managed to create a static route to 192.168.30.1 with a metric of 2, 192,168,10.254 being the jump.

  Success, the connection worked, the only problem is that now my guest network can see my business network because the corporate network uses the static route on my router to router on the guest network (due to the limitations of this device I can't do anything about it)

  So basically, what I have is

  Network Guest can connect to Business VLAN switch. I guess that's because the router is on the VLAN of Business and the default gateway is the router. As they are on the same network the Guest inevetably network can see the network and the server of the company.

  The network of the company can return to the network invited through the router using my static route, I created. The static route is really basic and I can't create a firewall on the router rule to prevent the business network addressing network comments because there is only one LAN - WAN firewall and this connection is LAN - LAN.

  What I need, is...

  somehow stop all traffic from the 192.168.30.0 network routing to what anyone on the 192.168.10.0 network, apart from the router to 192.168.10.1.

  Is this possible? I have this setup at several different site, the only difference is that I have a router from CIsco security on the latter with the VLANS configured so that I don't have this problem. Because I have a Netgear DGN2200 rather limited, I cannot configure the VLAN correctly, and as such, I need to see if I can do this on the switch somehow.

  Any help would be appreciated.

  It is my first post says in the way, so if I missed something that anyone would help then please let me know.

  Kind regards

  David

  Hi David,

  Why not apply an access list to filter incoming traffic in the SG300 switch such as, via the command line or GUI.

  Here is an example below, certainly not comprehensive, just an example

  ,

  Remember, we use the reverse masking of the ACE;

  config

  restrictGuest extended IP access list

  deny ip 192.168.30.0 0.0.0.255 192.168.20.0 0.0.0.255
  deny tcp 192.168.30.0 0.0.0.255 any 192.168.30.1 0.0.0.0 www
  deny tcp 192.168.30.0 0.0.0.255 any 192.168.30.1 0.0.0.0 telnet
  deny ip 192.168.30.0 0.0.0.255 192.168.10.0 0.0.0.255

  allow an ip

  output

  interface gigabitethernet1

  Service-acl input restrictGuest

  output

  Don't forget to save the configuration with the following command and respond to the prompt.

  To write

  or do it via the GUI method

  Step 1.  Create an ACL name

  

  step 2, add the ACE base port which is the list of filters.

  

  step 3.   Apply or binding the list to a port so that the port can watch and filter pattern matches to detect traffic in the switch.  I gave you an example of an ACE list above, you can be more creative in what you refuse.

  

  step 4. Now add or copy the entry in other ports on the switch.

  Be sure to save your changes to the configuration.

  I hope this helps.

  Best regards, Dave

• Create droplets to batch convert the image of 4000x4000px in 300 DPI / 72 dpi 1000x1000px / 500x500px by 72 dpi

  First time posting here and salute to all the gurus,

  I created a droplet to convert batch of images to ' 4000x4000px by cmyk 300 DPI jpeg / 72 dpi rgb jpeg 1000x1000px / 500x500px by 72 dpi rgb png "and record in the respective folders, but was met with some problems where the drop is not convert images to the planned size 1000x1000px jpeg 72 dpi."»

  The list of my actions are as below.

  

  This is when I ran the drop, the resulting image was still at 300 dpi, although the pixel dimensions changed 1000 x 1000. Could someone show me where I so bad?

  To tell the truth-Actions have as hard time saving file where you want to with the names you want. Lot can help because it can override save as ad defined stages the destination.  You never said what version of Photoshop you use.  IMO, you'd be better off forgetting about creating an action to create a droplet or using Photoshop batch.  What you try to do is better with Photoshop scripts.  In this case, failed to write the Script.  You should find script Image Processor Pro plug-ins and download it and to use the process you images.  You can customize simple action that you create. In fact, a different action can be used for each file that you want to copy. Script options allow you to control where the files are rolls to and has many options of naming. The Script can also resize your image to fit the size you need.  Each output process of file with a copy of your image. For each output process is independent does not necessarily concern himself with other processes of output file. Each process is distinct from the others.  The dialog Script is flexible and you can add custom tabs to create output files.  Because the computer has plugin you can even save its use in actions.  The action will have all the setting that you used in the recorded in the action scripts dialog box and when the action is played no dialog box will be displayed. The saved settings will be used.

  

• How can I remove images

  Hello

  I want to use the shop for sale services and I do not need the product images.

  Is there a way to remove images and placeholders?

  
  

  Thank you very much for your help!
  

  Go to your layout of the small shop and remove the tag from the image and html elements that may be wrapped in it. You probably need to remove all thus associated CSS.

• Can I run the Microsoft Windows Malicious Software Removal Tool w / Kaspersky AntiVirus with/without any problems?

  Can I run the Microsoft Windows Malicious Software Removal Tool w / Kaspersky AntiVirus with/without any problems?

  Can I run the Microsoft Windows Malicious Software Removal Tool w / Kaspersky AntiVirus with/without any problems?

  Yes.  It is a tool on demand and not in real time thus creates no problems or conflicts with the other application in real time, including Kaspersky Antivirus.

• I want to download Creative Suite Design Standard CS6 on my new computer. It says image not recognized. What is the problem? Thank you

  I want to download Creative Suite Design Standard CS6 on my new computer. It says image not recognized. What is the problem? Thank you

  Please try to download using download Creative Suite 6 applications

  Concerning

  Hervé Khare

• Need to recreate the image tool for px4 - 300 d

  I have a PX4 - 300 d, which was not used for some time, and readers have been removed for something else. I'm looking to return to service as storage for a VMWare ESX host iSCSI. I put new readers in and started, it took a bit, but she finally found the dhco server and made an IP address. I can access the px4 - 300 d, but it's a secutiry configuration screen and I can't spent to set up the storage. Is complaining about the Security screen "can not configure security up to this storage is configured.

  So I'm in a catch 22, so I want to just reload the firmeware and start from scratch. There is no data on the drives, nothing in the configuration of the PX4 - 300 d, which is necessary.

  And the best thing is the big missed 30 days ago and support is not interested to talk to me. they will provide this utility? I know it exists they sent me a version of it about 2 years ago although he has failed, they had to send me a replacement unit.

  Anyone know how we can get a copy?

  Thank you

  Jmorrison919,

  The imager can be engaged on the forums, but you can contact support here:
  https://Lenovo-na-en.custhelp.com/app/ask/

• Cisco SG 300-20 switch connects to the router

  Hello

  I try to install my new switch Cisco SG300-20 in my local network, but I'm not succeed.

  The SG 300-20 fails to connect to my router.

  When the router is directly connected to the SG 300-20 I fails to obtain the DHCP configuration. Any port I try fails.

  When I add a former switch between the router and the SG 300-20, SG 300 - 20 manages to get the DHCP configuration.

  When I use a static IP on the SG 300-20 and the router is directly connected, it is not an operational bridge in the IPv4 configuration.

  Where I'm looking for a solution?

  The SG 300-20 is maybe defective and I would stay there?

  A. van Egmond

  A few things you can check are:

  See if the system is blinking. If it is the default ip address. If it is solid the IP address has changed due to a static assignment or DHCP.

  If no link light is on or the system flashes, the reason why could not tear out DHCP is due to a shift of port negotiation. Try setting the port on the router or the full 100 MB switch or what ever you like just to see if that helps.

  Make sure that you are also on the latest firmware.

  Try factory default of the switch with the button of reset for 45 seconds.

  Cisco Small Business Support Center

  Randy Manthey

  CCNA, CCNA - security