Configure the VLAN voice and data in CISCO SF 300 8 P
I have a couple of Cisco SF 300 8 P and P 24 switches. I have voice and data VLANS configured as:
Data VLAN: default 145.17.59.0/24
Voice VLANS: VLAN 20 172.22.20.0/24
I have different DHCP servers regarding the data VLAN, we have a physical server that is configured for 145.17.59 * extended IP and Voice VLAN DHCP Server is configured as a router gateway with option 150.
This configuration works very well with other cisco 2960 switches and 3750 etc. except CISCO SF 300 8 P and 24 p. I tried to set up the voice and data VLAN in these CISCO switches so that phone CISCO (model 6941) should get IP of the VLAN voice and PC should get the IP address of the DHCP server on the data VLAN. I tried several techniques such as LLDP, Port-to-VLAN Config etc.
Can anyone please guide me / help on this.
Kind regards
A K.M.Sayeed
Hi A.K.M., with Cisco phones you should be able to define simply automatic voice VLAN to be VLAN20.
ID of the vlan 20 voices
You must ensure CDP or LLDP is enabled as well. I would check in the web GUI. DHCP for phones can come from a DHCP server on a port access VLAN20 switch, or you can use dhcp for assistance to redirect DHCP server elsewhere.
If you prefer or you have problems with the CDP or LLDP, you can also program the ports as trunks and add the tag VLAN 20 for them. In this scenario, you need to ensure inter - vlan routing works and phones that download the file config with corrrect VLAN config.
These switches do not run ios, so they are similar, but different from the catalyst switches that you mentioned.
-remember messages useful rate.
Tags: Cisco Support
Similar Questions
-
VLAN voice and data on a single port
Hello
I have some 5548 P Dell switches, but I just Cisco environment.
I find a lot of information on this but most of it relevant to the VLAN marked and unmarked on a port in general. Some articles suggest to put the port in trunk mode...
anyway (without taking into account the QoS) how you would accomplish this example Cisco on a Dell switch:
Switch (config) #interface g0/1
Switch(Config-if) #switchport mode access
Switch(Config-if) #Switchport access vlan 50
Switch(Config-if) #voice switchport vlan 10
Thank you!
For general mode, commands would be present as follows.
Console (config) # interface gigabitethernet 0/1/1
Console # switchport mode general
Console # switchport general allowed vlan remove 10
Console # switchport General allowed vlan add 2,3,4,50 tag
Activate console # vlan VoIP
Trunk mode:
Console (config) # interface gigabitethernet 0/1/1
Console # switchport mode Trunk
Console # switchport Trunk allowed to remove vlan 10
Console # switchport Trunk allowed vlan add 2,3,4,50
Activate console # vlan VoIP
-
Trouble with the voice and data Vlan vlan translate between CT3905 and SF300 - 24 p
Hey actually, we have the solution to monitoring of implementation with CT3905 phone, SF300 - switches 24 p cameras and AIR-AP1041N Access Points
We have the problem with the vlan tag in SF300 switch ports - 24 p we can´t tag vlan of the voice and data VLANs on the same port on SF300 - 24 p it is Possible or we must dedicate a port for each VLAN or ussing the same data segment of VLANs and vlan voice?
Someone has an answer or technical documentation that can help us
Best regards
First of all,
Please disable lldp transmit in SF 300 switch.
The command is "no lldp transmitted."
After you disable check the following steps.
https://supportforums.Cisco.com/docs/doc-27005
facing the same problem with cisco SG 300 and 3905 ip phone switch.
And nested thing was my 7945 and 6941 phones use to work properly, without above configuration.
Cisco 3905 became not vlan Ip address votes and even if I put static, it did not work.
After a long struggle, I was able to solve the problem. Now both phone and system work fine in the same port.
Samantha
-
How can I get voice and data to work with the ASA 5505?
Here's the issue I'm having. Can I get a Cisco 7940 to work behind one site to another configured ASA 5505 and I can also get data to work behind it. However, when I try to create a separate Vlan for voice and data, it does not work. Our voice VLANs on our remote sites are 172.30 and data are 172.31, when I put the inside interface with 172.31 data will work and when I on it 172.30 voice will work. I upgraded to a security more license and tried vlan3 created as voice. I have the data to the top and work but I can't get vlan3 to work. Any help would be greatly appreciated. Thank you
Here is my current config:
hostname TESTvpn
activate the password xxxxxpasswd xxxxx
username admin password xxxxx privilege 15
name Corp_LAN 10.0.0.0
name 192.168.64.0 Corp_Voice
name 172.31.155.0 TESTvpnobject-group network SunVoyager
host of the object-Network 64.70.8.160
host of the object-Network 64.70.8.242the Corp_Networks object-group network
network-object Corp_LAN 255.0.0.0
object-network Corp_Voice 255.255.255.0interface vlan2
nameif outside
security-level 0
IP address dhcp setroute
No tapinterface vlan1
nameif inside
security-level 100
IP 172.31.155.1 255.255.255.0
No tapinterface vlan3
nameif Corp_Voice
security-level 100
IP 172.30.155.1 255.255.255.0
No tapoutput
interface Ethernet0/0
switchport access vlan 2
No tapinterface Ethernet0/7
switchport access vlan 3
No tapoutput
dhcpd allow inside
dhcpd address 172.31.155.10 - 172.31.155.30 inside
dhcpd dns 10.10.10.7 10.10.10.44 interface inside
dhcpd sun.ins area inside interface
dhcpd allow insideenable Corp_Voice dhcpd
dhcpd address 172.30.155.10 - 172.30.155.30 Corp_Voice
dhcpd dns 10.10.10.7 10.10.10.44 interface Corp_Voice
dhcpd interface of sun.ins of the Corp_Voice domain
enable Corp_Voice dhcpd
dhcpd option 150 ip 192.168.64.4 192.168.64.3Enable logging
exploitation forest buffer-size 10000
monitor debug logging
logging buffered information
asdm of logging of informationoutside_access_in list extended access allow all unreachable icmp
outside_access_in list extended access permit icmp any any echo response
outside_access_in list extended access permit icmp any one time exceed
access extensive list ip 172.31.155.0 inside_access_in allow 255.255.255.0 any
inside_access_in list extended access allow icmp 172.31.155.0 255.255.255.0 any
Access extensive list ip 172.30.155.0 Corp_Voice_access_in allow 255.255.255.0 any
Corp_Voice_access_in list extended access allow icmp 172.30.155.0 255.255.255.0 anyVPN access list extended deny ip 172.31.155.0 255.255.255.0 object-group SunVoyager
extended VPN ip 172.31.155.0 access list allow 255.255.255.0 anyinside_access_in access to the interface inside group
Access-group outside_access_in in interface outside
Access-group Corp_Voice_access_in in the Corp_Voice interfaceGlobal 1 interface (outside)
NAT (inside) 0-list of access VPN
NAT (inside) 1 172.31.155.0 255.255.255.0Enable http server
http 172.31.155.0 255.255.255.0 inside
http 172.30.155.0 255.255.255.0 Corp_Voice
http 192.168.64.0 255.255.255.0 Corp_Voice
http 10.0.0.0 255.0.0.0 inside
http 65.170.136.64 255.255.255.224 outside
SSH 10.0.0.0 255.0.0.0 inside
SSH 172.31.155.0 255.255.255.0 inside
SSH 65.170.136.64 255.255.255.224 outside
SSH timeout 20management-access inside
dhcpd outside auto_config
Crypto ipsec transform-set esp-3des esp-md5-hmac VPN
crypto map outside_map 1 is the VPN address
peer set card crypto outside_map 1 66.170.136.65
card crypto outside_map 1 the value transform-set VPN
outside_map interface card crypto outside
crypto isakmp identity address
crypto ISAKMP allow outside
crypto ISAKMP policy 1
preshared authentication
3des encryption
md5 hash
Group 2
lifetime 28800tunnel-group 66.170.136.65 type ipsec-l2l
IPSec-attributes tunnel-group 66.170.136.65
pre-shared-key xxxxxoutput
int eth 0/1
close
No tap
int eth 0/2
close
No tap
int eth 0/3
close
No tap
int eth 0/4
close
No tap
int eth 0/5
close
No tap
int eth 0/6
close
No tap
int eth 0/7
close
No tapPeter,
Note that access list names are case-sensitive, so you've actually done something different from what I proposed.
Please do:
no nat (Corp_Voice) 0-list of access vpn
No list of vpn access extended permitted ip TESTvpn 255.255.255.0 everything
IP 172.30.155.0 255.255.255.0 extended vpn access do not allow any list allextended VPN ip 172.30.155.0 access list allow 255.255.255.0 any
NAT (Corp_Voice) 0-list of access VPN
In the case where you did deliberately, for example to separate the 2 acl: note that acl VPN (upper case) is also used in the encryption card, where you cannot add a second LCD.
So if you want to separate you, you will need 3 access lists:
list of access data-vpn ip TESTvpn 255.255.255.0 allow one
voice-vpn ip 172.30.155.0 access list allow 255.255.255.0 any
access-list all - vpn ip TESTvpn 255.255.255.0 allow one
access-list all - vpn ip 172.30.155.0 allow 255.255.255.0 any
NAT (inside) 0-list of access vpn data
NAT (Corp_Voice) - access list 0 voice-vpn
outside_map 1 match address all vpn crypto card
Don't know if this was also clearly to my previous message, I recommend you to replace the "all" (in each of the ACL lines) to something more specific (i.e. a remote network, or group of objects that contain the remote networks).
HTH
Herbert
-
Configure the vlan with SG 300 - 10 p and 520 SA
Hi all
Forgive my ignorance, but I need help with the basic configuration.
For a small office, I bought an appliance of security SA520 (for future VPN with another remote desktop) and a switch of SG 300 - 10 p to connect 3 PCs and 3 IP PHONE. The SA 520 is the router. I have to configure 2 VLANS on the switch:
VLAN2: DATA (for PC)
VLAN3: VOICE (for IP PHONE)
VLAN1: BY DEFAULT.
How can I configure simply all ports?
I would like to configure ports 1-4 on 5 to 8 ports and VLAN2, VLAN3 and G10 port is reserved for the SA520 router.
I want to split VOICE and DATA network.
I think I need to create a trunk on G10 to SA520...
Can someone help me?
Hi Julien,
OK sounds like you use it vlan by default for network management and the vlan 2 for vlan3 for voice and data.
I use a calculator for this, my SA520 is ready at the present time.
Step 1 On the SA520 add vlan 2 and vlan 3 and label them voice and data respectively.
Step 2. Allows you to use the switch port 4 on the SA520 as a port to shared resources to the SG-300.
(my intent is to use vlan1 not tagged vlan tagged 2 and vlan tagged 3 on the uplink of the switch and the SA500.)
To do this, I have to say the SA520 port 4 of the switch will be in trunking and not access mode.
You will need to check the membership of vlan 2 and vlan 3 on switch port 4.
Step 3. Now add a few IPS to VLAN2 and VLAN3
Step 4. Create DHCP scopes if that is what is needed on the SA520
So now I hope that we have the SA520 with the associated IPS VLAN1, VLAN2 and VLAN3
We also have the switch port 4 as a network interface
We are vlan1 reproducing unidentified and vlan2 tag and tag to the SG-300 switch vlan3.
We do the opposite on the SG-300 switch.
If you use G10 as the uplink to the SA520 you'll notice of default port 10 must already be in trunk mode.
Switch ports G10 should be marked for vlan 2 and labelled for vlan3. It will be, default Gi10 untagged for vlan1.
Make sure you keep ports switch is correctly set up.
Best regards, Dave
-
How to configure the VLAN-access plan on Cisco 3650
Hello
I would like to configure the VLan-access plan to filter some of the traffic VLAN, but I am unable to run vlan-map command on the cisco L3 3650 v03.06.00E
Hello ahmed,.
According to the command search tool, 3650 v03.06.00E does not support the vlan-access plan.
You will need to catalyst 3650, 3SE to configure "vlan access map.
https://Tools.Cisco.com/support/CLILookup/cltSearchAction.do
Show vlan-plan of access (catalyst 3650, 3SE)
VLAN-access plan (catalyst 3650, 3SE)
I hope this helps.
Please evaluate the useful messages.
Thank you.
-
Lack of voice and data at the same time kills me
After using a treo 750 (WM 6.1) on att for the past three years, I guess I did not realize the advantage of ATT and gsm in general. There are many drawbacks... mainly pricing for simple accounts (However their family plan was directly comparable to those of sprint). I constantly try to use data applications while talking on the phone without success. I started thinking that I could do without, but a week later, I still really really miss. My wife did too... because she's I usually give directions or any other web information while on the phone. There is nothing like view google satellite map to help someone make sure they are in the right place... "see a big tree on your right with a large Brown building behind it, Yes, it's that one" does anyone else have this feeling? WiFi is not an option for me most of the time.
Voice and data at the same time is not available when using any CDMA network due to network constraints. This is true for all types of phones, not only Palm or not only the Pre. Your example of electronic control or by using google maps, the gps data that can be stored before you activate the call. try to browse the web while making a call and try to go to a web page, you have never visited before, so that you know, that he cannot be a version collected page.
-
Problem blackBerry Smartphones on the use of the voice and data
Hello
When we use the Blackberry Desktop Software for backup/restore data from one phone to another, will check voice and data usage in the session "peripheral and buyer information - status remorse" also be restored from the old phone or affected by synchronization? Or will they count just use since the first use of the new phone?
Harold Lee
I have to admit, I am not an expert on this subject, but that is my impression. Once you get the new phone running, your meter would reset to zero on this phone.
-
A bet with the network team - configure the VLANs on Teddy does not work against Cisco?
Hello
We have a great place of Esx and I have a bet with one of the network Admins.
I configured a vSwitch to work with 1 bear. On this vSwitch I configured 1 vlan with a Vlan ID 100
I told the guy from the network to set up the bear side here and he said he has set up 'Access' and not trunk as normally I ask because it's only 1 Vlan.
I said ok and we tried and nothing works, when I configured the Vlan 0 in the Esx, it started working.
Of course we cannot leave it like that and need to Config the Vlan on the Esx.
I told them that once I configured the Vlan on my side there is nothing to do there, and they need to do the thing here.
they say the same thing.
Who is right? It is something they need to configure side here if she's 'access' and not 'trunk '?
or is it something at my side?
This mayble help your network http://kb.vmware.com/selfservice/microsites/search.do?language=en_US&cmd=displayKC&externalId=1004074 management team
and
Please, do not forget the points of call of the "useful" or "correct" answers
Mauro Bonder - moderator
-
Subject of the vlan voice SRW224G4P
Hello
I have configured the SRW as vlan, use vlan for voice 212, 348 for data and communicate with cisco IP Phone.
database of VLAN
VLAN, 210-216 345-348
output
ID of the vlan voice 212!
!
interface fastethernet1
activate the storm control
Storm-control broadcast level 10
Storm-control include multicast
maximum port security by 10 points
port security mode max-addresses
port security throw trap 60
spanning tree portfast
switchport trunk allowed vlan add 212
switchport trunk vlan native 348
macro description ip_phone_desktop
! next order is internal.
macro auto smartport dynamic_type ip_phone_desktop
!but when I show vlan voice,.
It shows:
=====================================
1ASW01 #show voice vlan
Manage the VLAN voice State is automatically triggered
Operational status of VoIP VLAN is enabled in auto
Best Local Voice VLAN ID is 212
Best Local VPT is 5 (default)
Best Local DSCP is (by default) 46
Concerted VLAN voice is received from the 34:62:88:73:05:c9 switch
Concerted VLAN voice priority is 0 (static source active)
Concerted Voice VLAN ID is 216
Agreed VPT is 5
Agreed DSCP is 46
Voice VLAN agreed last change is 3 May 13 05:06:31=====================================
I don't know why the vlan 216 became the vlan voice?
I tried changed the build-in macro settings,
auto macro of the built-in parameters ip_phone $native_vlan 348
auto macro of the built-in parameters ip_phone_desktop $native_vlan 348but the system could not change the value of $voice_vlan.
How to fix?
Hi Skywings,
So I think the above output is after the change, right? If this is true, it seems that something was wrong during the configuration process. Process of VLAN automatic voice has two main phases where one is related to communication between the switches and other Cisco infrastructure devices and synchronization of voice VLAN ID. The second phase is related to the identification of the end device as phone. What I see in your case that the first phase has failed somehow the voice VLAN ID is different from locally configured. Can you share with me your race and also start-up config more CDP neighbors? You can use private message.
Kind regards
Aleksandra
-
Simultaneous voice and data on Verizon?
OK, you can now pre-order the phone, and yet I saw no confirmation one way or another as to if the Moto X play supports simultaneous voice and data on Verizon. I tweeted Verizon today and they claim that they do not have the specs of the phone.
I can't believe anyone, namely, Motorola and Verizon, are able to answer this fundamental question.
My Moto X (2014) can not STILL can't do, so I am wary to this model as well and rightly.
Can we please get a definitive answer?
Yes, you can get simultaneous voice and data on Verizon.
-
ASBL voice and data simultaneously
Anyone know why we can not make a phone call and use data at the same time on the VZW network? I am able to do that with my 1st gen Moto X, so it seems just stupid my 2nd generation cannot do.
I discovered this last week I was on the phone with my daughter and I tried searching movie times while talking to him. I thought there was something wrong with my phone until I did some quick research and noticed that it is the same for all the 2nd generation Moto x on VZW. I don't know if there is a problem with other providers.
all this is part of the improved A.s.b.l. appeal have VOLTE 'coming soon'... a giant step in the wrong direction from what I hear the bike X 2014 is not the only phone to suffer from this "feature". The droid turbo also can not do. I heard a rumour nasty that even the Nexus 6 cannot, but that sounds not just because all the specs show the antennas in the unit.
The X must wait for VZW to flip the switch and hope that it works as expected.
The other weird thing is when I talked to a technician at bike he said that X was supposed to have simultaneous voice and data.
-
When sending emails to the bcc and access to a group, I hit the button send and dates back to the Inbox without sending. I even changed users on my pc and it always does. I closed temporarily add-ons thinking that would help, but did not seem to make a difference. Can I have a virus?
Hello
- E-mail are what customer you referring?
If you use Windows live mail, then the number you posted is related to windows live and will be much better suited in Windows live forums. Click on the link below.
Windows Live Solution Center
-
How can I get the exact time and date on my FAX LOG
I have a new HP Officejet 6500 has more on my Dell Inspiron Windows XP computer. How can I get the exact time and date on my FAX log?
Hi FrederickFrank7,
Journal of faxes would just follow the time of your printer. Please set the time and date of your printer.
I am an employee of HP.
Please indicate the position that solved your problem as "acceptable Solution". -
I want to use a USB device to connect to the Internet, as my ethernet card is US I can not configure the Ralink dongle and I am referred to in article 871122 on the Microsoft site to activate zero wireless connections. How to do this please?
USB to the Internet connection.
Hello
It seems that your dongle is not installed properly. try to uninstall and reinstall the software dongle...
Maybe you are looking for
-
15 - 1209wm: p 15-1209 foregot power on password
power foregot HP 15-1209 on the error code password 63232314.
-
in my hp tablet, keyboard android as well as game store is not working.i tried to format my tab but it dosent format such that it needs a password and I can only fill my password with the keyboard... .What do I do?
-
Will be 3 GB Thinkpad W500 with Intel Core 2 Duo T9900, 320 GB HDD, ATI Mobility FireGL V5700 graphics.
-
Differece in the versions of windows?
Hello. What is the difference between this version? Windows 7 Home Premium (x 64) X 17-24209 and X 17-58997? And what is the latest version of Windows 7 Home Premium x 64? And you can give a link where I can download it?
-
How to get the version of the app
Hello I found that we can get the latest version of the app using the ApplicationInfo.but the thing, it's when I try to apply it he throws do file errors.can anyone know how to do this in a better way. thanking you.