Repeat items in a stacked sequence

Similar Questions

• Order the dish/stacked sequence excecutes

  

  Normally, a flat structure to sequence in a loop for if Execute from left to the right until it reaches the end and then repeat the left right code as many times as the loop he tells too much.

  I want to be able to change the order / discreet in which the sequence loop around, so that my excecutes stacked in the 'Z' patter above sequence.  He needs to realize from left to right until it gets to the end, then bounce back (without repeating the last image) and run from right to left, until it hits the start frame, bounce again (without repeating the start frame), and executed from left to right to what he hits the last image, bounce back again once , etc etc etc, many times I have to say.

  Tips on how to achieve this?

  Forget the flat/stacked sequence diagram. They are only as a LAST resort.

  If all your actions was I sup vi then call one by one in a while loop. You can use a cluster of error to force the flow of data between the sub of vi.

  If not go get some Statemashine. There are a lot of entries on this site for State mashines in LabVIEW.

• The output of a stacked sequence index

  Hello world

  I write code in which I instantiate objects much when I first start my code and place objects in a table that is subsequently used as a lookup table in the operation.  It takes a lot of space on the block diagram and it is difficult to understand for the user who is not familiar with the code.  Is it possible to create something like a sequence of plate which may have a single indexed exit tunnel?  I want something like what you get when having a tunnel on a loop for, I want just every single itteration (unlike the loop for).  I have included a picture of what my schema currently looks like for reference.  You can see that I have create all the objects with unique information (ID, order number, etc.) and then create a table with them.  I would like for each of these objects in an image of a sequence that is stacked with a single indexed output instantiate (if possible).

  Thanks for the tips!

  -Eric

  Option 1: use a Subvi

  Option 2: Use a loop FOR as a sequencer.  Instead of the structure of stacked sequence (or flat), put a case inside a loop structure FOR and wire the i for the selector of the case.  Then, in each case, you can initialize a different class.  The output can then be autoindexed.

• structure of stacked sequence

  OK, so what I try to do is to use LabVIEW 8.0 and a USB-6008 is a photocell allows to start the rotation of a motor continuous when it is in the darkness and stop the motor function once it is exposed to light.  Only after the engine stopped moving I want then to a linear actuator to deploy.  Separately all programs work as it should and I was able to integrate successfully the photocell function and motor.  What I can't do, is get the actuator to deploy once the engine has brought his designated position.

  I was planning on using a structure of stacked sequence so that I make sure the actuator goes off until the engine has completed its task.  Because I need to have the photoresistor and the engine in a while loop to ensure that they are constantly looking for the data telling them what to do, I placed them in the while loop and the motor part of the code in a frame of the stacked sequence.  Once the motor stops, I then passes the data forward to the next section, which is just a Boolean wire coming out then the structure of the sequence in a loop to give the necessary tension to control the actuator.  However, it does not, the engine continues to ork in synchronization with the resistance, but the trigger does not fire.  I wonder if there is something wrong with my attempt to pass off while the structure data.  As I read on stacked sequences, it seems that many people do not use them because they do not work properly in time so I wonder if there is a way to avoid using one but to make sure that the actuator will not draw unless the resistance has guided the motor in position.

  I have attached the code to help the understanding of the program.

  I use a bridge allowing movement front and rear H, you will see a 3 x 1 matrix in the structure of the case.

  Thank you!

  Hi Leanne,

  You could use a digital logic to check for a change in value, and the value itself.  In the example below, I did this with a feedback node that stores the value of the digital line of the previous loop iteration:

• question about stacked sequence

  Hello

  I have a question about stacked sequence.

  I have a stacked with 5 sequences sequence (0,..., 4). I would like to run these as this form

  0, 1, 2, 1, 3, 1, 4, 1 then again 0...

  I don't want to duplicate the section 1 because it contains many objects, variable... One possibility would be to out objects and then duplicate the sequence and use of shift registers, but I don't want to use because in 1, I have some graphs in real time to draw...

  Will there be another (easy) way to do this?

  Thanks for the ideas,

  Concerning

  Why use a stacked sequence?  What you want is a state machine something like this

• Linking a sequence of XSD schema to subform repeated items

  Hi, I have created a form with the rows in the table that is repeated using an Add button to add rows dynamically. I lie the line with the schema xsd with a [*] at the end of the option of data binding with ticked repeat rows for each data item. All by submitting the form as XML data to java controller I get only one line of the table and not other lines dynamically added by add the functionality of the button.

  

  

  I want to know that how generate the XML for lines added dynamically linked with an XSD schema.

  I also explored the link below, but is not to solve the problems:

  http://www.Adobe.com/devnet/LiveCycle/articles/binding-XSD.html

  Thanks in advance

  I have solved the problems by adding maxOccurs = "unbounded" in the xsd schema with the name of the bound element.

• Running a Subvi independently in a stacked sequence

  Of expensive Labviewer. We have an instrument that is controlled by a labview program. The program consists of a bunch of operations in sequence and each operation is implemented using sequences la_ROSE923/flat. At some point in the sequence, I want to ramp a furnace (owen) external to a given temperature, for a period of 5 to 10 minutes to do this, I did a Subvi who works for this purpose (using a while loop set). If I put the Subvi in the structure (sequence stacked/flat) all of the process holds it until my Subvi is finished, but I want the overall process to move to the next sequence just after starting Subvi. How do I implement that?

  Any help is highly appreciated

  Warmly optimistic

  Morgan

  You can use any loop in parallel.

• using the same indicator of string in different stacked sequences

  Hi guys, I want to use the same string in different sequences stacked indicator. I tried to plug the output of each string constant through the sequence on my indicator chain outside the block in the sequence, but then I get an error "wire connected to a tunnel not channeled. What is the best way to use the same indicator for all sequences?

  Hi JoVMo,

  You can just use a local Variable of this indicator within the sequence...

  

  Kind regards

  Nitz...

  (Kudos are always welcome)

• What is the value of repeat items only?

  I'm trying to understand the value of repeating only objects. I was hoping to create a list with the editable elements < li > and < li > does not have a tag that is supported for the editable regions. But it is supported as a repeat region. Can someone explain to me, or provide an example of the real world, of why this might be useful to the customer? In other words, why a customer would want the opportunity to move up, down, add, or remove an item, but not be able to change the content of the element?
  
  Is there a workaround to create a combo box or list items?
  
  Thank you.
  

  Hello antlion.

  You can wrap the content of the

• s in editable divs. You have created your repeating group and applied repeatedly = "true" for the list items, but only InContext Editing allows regions editable on div, th, and td elements.

  In Dreamweaver, select the content of your

• then choose Insert > InContext Editing > create editable region. Dreamweaver invites you to 'wrap the current selection with a DIV tag and then transform '. Click OK, and then repeat this step for each item in the list. The result will create boxes for your list items, and you look at something like:

• The project import items, why is "no sequence"?

  I'm new to Prem CS5 and am evaluating. I created a project into components and importing (conversion) in CS5 is reports ' Video Filter missing: Æ.» ADBE ObjectTracking' and when it loads the timeline shows "no sequences.

  In elements, the project has a lot of video tracks, overlays, storytelling, etc. on the timeline.

  Where can I find this in CS5?

  Note that all resources are present in the browser of the 'project '.

  Double click on the sequence in the project Panel.

• Extract a repeated item

  Hello!
  
  I use Oracle 10 g 2.
  
  How can I retrieve the value of the IUM tag? Is this correct syntax (a repeated element of many times without a group above it)?
  
  When it is an attribute of the cxMed tag, I can do what I need (code below).
  

    WITH tmp AS
    (SELECT XMLTYPE('<root>
                      <inf>
                        <det nItem="1">
                          <prod>
                            <med>
                              <nLote>lote 0</nLote>
                              <qLote>0</qLote>
                              <dFab>2011-03-01</dFab>
                              <dVal>2012-03-01</dVal>
                              <vPMC>300</vPMC>
                            </med>
                            <med>
                              <nLote>lote 1</nLote>
                              <qLote>1</qLote>
                              <dFab>2011-01-01</dFab>
                              <dVal>2012-01-01</dVal>
                              <vPMC>100</vPMC>
                              <IUM>1</IUM>
                              <IUM>2</IUM>
                              <IUM>3</IUM>
                              <IUM>4</IUM>
                              <IUM>5</IUM>
                            </med>
                            <med>
                              <nLote>lote 2</nLote>
                              <qLote>2</qLote>
                              <dFab>2011-02-02</dFab>
                              <dVal>2012-02-02</dVal>
                              <vPMC>200</vPMC>
                              <cxMed IUM="1">
                                <IUC>21</IUC>
                              </cxMed>
                              <cxMed IUM="2">
                                <IUC>22</IUC>
                              </cxMed>
                              <cxMed IUM="3">
                                <IUC>23</IUC>
                              </cxMed>
                            </med>
                            <med>
                              <nLote>lote 4</nLote>
                              <qLote>4</qLote>
                              <dFab>2011-04-01</dFab>
                              <dVal>2012-04-01</dVal>
                              <vPMC>300</vPMC>
                            </med>
                          </prod>
                        </det>
                        <det nItem="2">
                          <prod>
                            <med>
                              <nLote>lote 1</nLote>
                              <qLote>1</qLote>
                              <dFab>2011-01-01</dFab>
                              <dVal>2012-01-01</dVal>
                              <vPMC>100</vPMC>
                              <IUM>1</IUM>
                              <IUM>2</IUM>
                              <IUM>3</IUM>
                              <IUM>4</IUM>
                              <IUM>5</IUM>
                            </med>
                          </prod>
                        </det>
                      </inf>
                    </root>') as XMLArquivo from dual
    )
            SELECT --/NFe/infNFe/det
                   vw.nItem,
                   --/NFe/infNFe/det/prod/med
                   vw2.IdMedicamento,
                   vw3.IdIUM,
                   vw3.IUM,
                   vw3.IUC
              FROM tmp,
              XMLTABLE('/root/inf/det'
                       PASSING tmp.XMLArquivo
                       COLUMNS
                         nItem  NUMBER(3) PATH '@nItem', 
                         medXML XMLTYPE   PATH 'prod/med') vw,
              XMLTABLE('/med'
                       PASSING vw.medXML
                       COLUMNS
                         IdMedicamento FOR ORDINALITY,
                         cxMedXML XMLTYPE PATH 'cxMed') vw2,
              XMLTABLE('/cxMed'
                       PASSING vw2.cxMedXML
                       COLUMNS
                         IdIUM FOR ORDINALITY,
                         IUM NUMBER(13) PATH '@IUM',
                         IUC NUMBER(18) PATH 'IUC') vw3

  Thank you
  Luciana
  
  Published by: Luciana on 21 January 2011 08:33
  
  Published by: Luciana on 21 January 2011 08:34
  
  Published by: Luciana on 21 January 2011 09:47

  Hi Luciana,

  Something like that?

  WITH tmp AS
    (SELECT XMLTYPE('
                      
                        
                          
                            
                              lote 0
                              0
                              2011-03-01
                              2012-03-01
                              300
                            wcv
                            
                              lote 1
                              1
                              2011-01-01
                              2012-01-01
                              100
                              1
                              2
                              3
                              4
                              5
                            
                            
                              lote 2
                              2
                              2011-02-02
                              2012-02-02
                              200
                              
                                21
                              
                              
                                22
                              
                              
                                23
                              
                            
                            
                              lote 4
                              4
                              2011-04-01
                              2012-04-01
                              300
                            
                          
                        
                        
                          
                            
                              lote 1
                              1
                              2011-01-01
                              2012-01-01
                              100
                              1
                              2
                              3
                              4
                              5
                            
                          
                        
                      
                    ') as XMLArquivo from dual
    )
            SELECT --/NFe/infNFe/det
                   vw.nItem,
                   --/NFe/infNFe/det/prod/med
                   vw2.IdMedicamento,
                   vw3.IdIUM,
                   vw3.IUM,
                   vw3.IUC,
                   vw4.IUM
              FROM tmp,
              XMLTABLE('/root/inf/det'
                       PASSING tmp.XMLArquivo
                       COLUMNS
                         nItem  NUMBER(3) PATH '@nItem',
                         medXML XMLTYPE   PATH 'prod/med') vw,
              XMLTABLE('/med'
                       PASSING vw.medXML
                       COLUMNS
                         IdMedicamento FOR ORDINALITY,
                         cxMedXML XMLTYPE PATH 'cxMed',
                         IUMXML   XMLTYPE PATH 'IUM') vw2,
              XMLTABLE('/cxMed'
                       PASSING vw2.cxMedXML
                       COLUMNS
                         IdIUM FOR ORDINALITY,
                         IUM NUMBER(13) PATH '@IUM',
                         IUC NUMBER(18) PATH 'IUC') (+) vw3,
              XMLTABLE('/IUM'
                       PASSING vw2.IUMXML
                       COLUMNS
                         IUM NUMBER(13) PATH '.') (+) vw4
  ;
  

  Must "CxMed/@IUM" and ' med/IUM' be in the same column?

• Adding items to an enum shifts the constant on the BD...

  A picture is worth a 1000 words, here is my qualm:

  

  Why adds an element to a constant of the enum addressing the constant of the comic?

  I use a lot this approach for Pseudo-stacked sequences (I use instead a state machine) and I end up spending the enum constant after adding item wach, otherwise, it ends by disappears under what structure it is right...

  Of course, I could just right-click and use the Edit items property (which I've been using today doing my level of tolerance has ebbed down a lot lately), but unless this feature has been voluntarily integrated in LV, it is bordering the sadist.

  Tested in LV 2011.

  Hi guys,.

  Thank you for this comment! I was also able to reproduce here on my computer running LabVIEW 2011 SP1.

  This was reported to R & D (CAR # 339320) for further investigations. Please let us know if you find other problems, we like always your diligence and your comments!

• Sequence special error in DAQmx create raster scan with 2 Motors of stepper motors: Error Code 200088

  Hello

  I am trying to create a LabVIEW program that controls two bipolar motors to create a raster scan. I use DAQmx and Labview 2012 SP1 with a usb 6008. I got the engines to move in one direction, but when I try and get them to move in another direction in a separate task, I get an error-200088 code indicating that my task is not valid. This happens at the beginning vi to move the motor x in the opposite direction of the task.

  The logic underlying the program is as follows:

  1. move the engine x a certain number of steps to the right

  2. move the engine are a number of steps down

  3. move the engine x the same number of steps as 1 to the left

  4. get off the engine is the same number of steps 2

  5. repeat

  I can get the steps 1 and 2 work but I have problems with step 3. I use a stacked sequence to show the task for each step.

  I appricate all the advice on this topic as part of a final year project

  Thank you

  Aoife

  You can solve this problem very simply.  Move all DAQmx departure calls happen * before * the structure of sequence rather than inside.  Similarly,.

  move all calls to DAQmx Stop and DAQmx Clear happen * after * the structure of sequence rather than inside.

  I would sequence the DAQmx Write calls to write the bit of direction * before * writing the bit clock.   And I highly recommend that wire you

  to the top of your tenants error and outs so you can be informed of any errors in the DAQmx tasks.

  -Kevin P

• Import sequences of multiple images in first effectively

  I'm about to start editing a project which includes a few hundred cinemaDNG sequences of images. Is it just me or are there at - there no way to import sequences of images in large numbers quickly and efficiently and without boring myself in a grave at the beginning?

  If I import a main folder that contains many subfolders of sequences of images, first think very long and then matter each sequence of images of hundreds of times. It seems to look in the folder image sequence, and then for each frame in the sequence import a version of the sequence of the entire image. Bonkers.

  The alternative is to import each of my sequences of images individually. Cmd - I, put you in the folder, click an image, wait for import, repeat hundreds and hundreds of times. I'm sorry but this is a shortcut to mental illness and/or carpal syndrome.

  Adobe. Please, I beg you. People want to work on many many sequences of images. Not one or two. Please get it together.

  Or am I missing something here?

  Lee Gingold wrote:

  I'm about to start editing a project which includes a few hundred cinemaDNG sequences of images. Is it just me or are there at - there no way to import sequences of images in large numbers quickly and efficiently and without boring myself in a grave at the beginning?

  If I import a main folder that contains many subfolders of sequences of images, first think very long and then matter each sequence of images of hundreds of times. It seems to look in the folder image sequence, and then for each frame in the sequence import a version of the sequence of the entire image. Bonkers.

  The alternative is to import each of my sequences of images individually. Cmd - I, put you in the folder, click an image, wait for import, repeat hundreds and hundreds of times. I'm sorry but this is a shortcut to mental illness and/or carpal syndrome.

  Adobe. Please, I beg you. People want to work on many many sequences of images. Not one or two. Please get it together.

  Or am I missing something here?

  First of all, what version of PrPro you are on?

  In all cases, you should not import each sequence of images of hundreds of times. If it does than 10 this part is a bug. What he will do when importing from parent folder level, must import each folder that contains each (sequential) image as a separate file rather than as a sequence of images. To import as a sequence of images, you must use the import dialog box. Browse to find the first frame of the sequence. When you have selected, you can check the "Image Sequence" option in the dialog style OS and then import it will know to import all the images as a single item of the image sequence. It is separate from a regular sequence PrPro point and is in fact just treated like any other clip media. However, it is true that you can not import many sequences of images at a time of in a common Press Kit due to this design limitation where the first image must be explicitly selected before the "image sequence ' box United Nations-grays." Part is a feature request.

  Adobe.LY/BugReport

• A sequence controlled by an input button

  Hi guys.

  I want to create a sequence that is commanded by an entry for example a button 'NEXT' button which will begin a set of instructions assigned to step 2 of a sequential structure. Something as seen in a software installation.

  Can someone point me in the right direction?

  Google for 'States LabVIEW machine' and also search here on the forum. If you want to use the 'flat sequence structure' or the 'stacked sequence', you're wrong. Use a machine to correct state.

  What you describe is easily manageable by using a State Machine, and you can do much more with it. For example, you can have a 'Next' and a 'Cancel' button, and according to the choice of the user, the state machine transitions into a different State. In the case of the next button, he will start doing some operations, for example (which must at any time be abortable ('Cancel' button), in short time, it is also an advantage of a machine good condition), and for the button cancel the State Machine will enter a State of 'Idle', pending new orders of the user and so on...