replacing existing ATE traditional PXI based ATE
Hi all
We use a traditional ATE equipped with traditional instruments for example transmissions cope, Agilent: switches; Mux; Matrix; DMM; Generating function, Chromaower supply, etc...
I contacted OR to obtain praposal to replace these instruments OR instruments. The price of the products OR is higher than the traditional instruments of compratively. Now it's hard for me to propose this to my managemnt.
Which in general; You people do to replace the traditional ATE with this new S/o, PXI?
Can I use same digitizer for high channel count to replace measuremnt instrument such as scope, DMM?
- DMM: PXI-4072 (I LOVE this DMM)
- Switches/MUX: NOR has a good range of PXI switches that work well. I wanted to play with of Pickering PXI switches, especially their BRIC.
- Function generator: the PXI-5421 is a very good generator of arbitrary signals.
- Power supplies: Agilent has a good series of modular power supplies (N6700 series). You can put up to 4 power supply is a single 1U chassis and communicate with them via LAN.
- I use Chroma electronic loads, but I don't really like them for situations that I was forced to use them. They are really good for loads of constant currents, but I hate them for the constant resistance loads, unless you are less than 100 Ohms. Always looking for alternatives. Also glued using GPIB or serial communication. I'm trying to push to the local network for cost reasons.
- Oscilloscope: I found that the transmissions expanded are the best way to go. It is really hard to replace a real screen on a scope that you can play with during troubleshooting. And the means of integrated measures, I don't have to deal with the wave form myself. Yet once, talk to her on local network.
- Counter source (power supply with a multimeter accurate built in): been using the Keithley 2425. Tempted to look at the NOR meters source especially because Keithley seems just refuse to go to the local network. But it's a counter very good source.
In my honest opinion, PXI has its place and have their own traditional instruments. PXI is very good for the right instruments (switches, multiplexers, DMM, AWG, low current power supplies to). But I find the traditional instruments are necessary for feeds that need to come out of the current charges and decent electronic (again, due to current needs). I used scanning cards of EITHER before, but I always come back when I have to debug and how it is nice to have a real screen showing my waveforms and then be able to play with the sliders on the fly.
Tags: NI Hardware
Similar Questions
-
If I export my contacts from my Windows Mail and import in another computer (same e-mail program), will be replaced existing contacts on this computer?
original title: about ContactsHello
Ideally, it should not be replaced.
See also: http://windows.microsoft.com/en-US/windows-vista/Import-export-or-change-the-format-for-contacts
-
I currently have a very disturbing system status:
"You must allow replacing the existing data to begin to use this appliance.
"Are you sure you want to overwrite existing data?"
The unit shall be set up a 8TB ix4 - 300 d in RAID (I forgot the number). I am still able to access and read / write from the network, and as far as I know that no other messages indicate that none of the drives failed.
How can I solve it without risking the 2 TB of data? What happens if I click on OK?
Hi whitby,.
The first thing I recommend you to do is backup your data even if it is still available and you can access and read/write to the device. Your unit is probably in RAID 5 because this is the default value for the device. With RAID 5, you can lose a single drive and be able to continue to access your data, but if another hard drive were to fail, your data will be lost and you need data recovery.
Once your data is backed up on a second location, you should be fine to replace the existing data and to rebuild the RAID. The real problem is that the drive is most likely a failure and it will be replaced soon. If you are covered by the warranty, I would recommend contacting technical support to send in a log dump so they can get more information from device to see if the hard drive needs to be replaced. The warranty covers the replacement of the hard disk. Otherwise, you will need to get a replacement of the hard disk that is the same manufacturer, speed, and as long as the original disks.
-
Loads of parallel data through SQL connect and replace existing data
I'm doing a load of multiple data through SQL Connect using the following statement. Just try to put in place a .bat file to automate the process but not sure that whenever it executes this statement adds data to existing or replaces the data? I tried to write an override for this but it works for instructions which contain the import section.
Import of database data App.DB connect as username identified by password
with the help of several rules_file, rul1, rul2, rul3
load_buffer_block starting with buffer_id 10 on error write to 'C:\\dataload.err ';
We can add spec commit buffer such as "replace all data ', 'create group', 'Add' to this import statement? The default declaration overrides the value whenever the data is loaded?
Thanks in advance!
you have an option in the rules file "Overwrite out of values."
rulefile > setting dataload > loading values
-
LR3 - Export in JPEG then add to the collection and replace existing?
Is this possible? I know how to export to JPEG, and then add the file in my collection, but is it possible to get it to automatically replace the image I just exported, also delete its settings? Basically just update the original file.
Thank you
I could give you several reasons why this is not a good idea, and also why it is beating all the non-destructive nature of Lightroom...
But no, I don't think that there is an automated way to do it. You must do this manually, but not worth it, it's just not a good idea. Just edit the photo in LR and the modified version appears in your collection, without export and by replacing the existing. Its much easier than what you propose.
-
Pop-up window: replace existing popup.
I have a link that opens a new page in a pop up window using the following link attributes.
This example uses a page rather than a URL link.
onclick = "Window.Open (this.href, '_blank ',' resizable = 1, scrollbars = 1, width = 760, height = 350, menubar = 0, location = 0, navigation = 0'); return false; "title ="Your Help ".
There is a slight problem that whenever I click on the link, a new window popup is generated.
Ideally, I want to be able to refresh the popup existing with the new data, if it already exists.
The alternative is to make the modal popup, then the user is obliged to shut it down before it can continue to the previous screen.
All Advisor, help appreciatedKeith:
Replace "_blank" with another string in the window.open method might do the trick.
CITY
-
Hello everyone;
I managed 10.2.0.4 binary installation is complete on 10.2.0.1. but we have made small
error when running root.sh we smashed existing oraenv coraenv db_home (10.2.0.1)
can I continue? or uninstall the patch?
Thank you...There should be no problem with this - it is recommended to use the latest versions of these files provided by the patch
HTH
Srini -
Conversion of computer virtual existing Bootcamp at VM-based complete
Right now, I'm under merger based on a Bootcamp partition. Y at - it an option to say merge to convert a 'full' of Bootcamp VM so that I can delete the Bootcamp partition? Of course, I don't want to go through the company to re - install Windows XP full.
Popular suspicion. Thank you.
Yes it is... it is labeled "import."
In the library window, select your BootCamp VM, on the right side there is a button named "import."
Until it clicks, let it do its thing and then run it to make sure it works.
Once you've verified that this works, you can trash your physical partition.
Hope that help =)
-
You will need to replace existing Web site pdf file. Help, please!
Our intern left this summer and we are clueless on Dreamweaver. We have a Spry Menu with a link to a pdf file of our employment application. Our application has been reviewed, and we need to replace it on the Web site.
From what we have gathered, Spry Menu Widget is no longer available for download, and we cannot change the link in a new file via the widget because the intern took his notebook with the installed widget.
So to do this, I downloaded the files from the website my Local folder, deleted the old application employment pdf file and replaced it with the new application with the same exact filename than the old.
My question is... If I point out the new application in our local folder and click on download, it makes the link in the menu to go to the new application?
Thanks for you help in advance!
Okay, of course. If we were to replace a pdf file linked in our spry menu bar. We had the widget and do not think that you could download it, then we went to the folder on the lower right part of the screen and open the remote folder. We then highlighted all files except for the / at the top of the file. Then we clicked on the arrow down to copy these files in our local folder. Once they have been uploaded, we went in the local and found the file folder that we needed to switch out. We then deleted this file, named our new file the same exact file name and clicked and dragged from our computer to the folder containing the file that we removed. Then we have highlighted in this file, click right and choose 'PUT', as Jon had instructed us to do above. Downloaded the file. When it was over, we checked our website and got an error because the pages would not load. However, a few minutes later, we tried again and everything worked perfectly. The new PDF had replaced a former and always connected correctly the MenuBar.
-
Hi all
is anyone able to help me out of this misery?
Thank you very much!
JürgenHello Juergen,
Unfortunately you cannot substitute an RS-232 cable instead of the standard MXI-4 cable. While both use a DB-9 connector, the pinout of each cable is different. Even if you were to manually change a standard serial cable, that you could have interference problems of noise due to the higher frequency MXI-4 compared to the RS-232 signaling.
-
OLIVIER on OBIEE without replacing existing domains
Hello world!
We want to install OLIVIER 7.9.6.4 on 11.1.1.7, but int OBIEE this instance we have a lot of dashboards and essbase cubes.
We need dashboards OBIA and old dashboards in the same instance.
Can I combine my RPD with OBIA DPR and my system-jazn - political "Data.xml" for this?
Any information or document you know.
Best regards.
Have you used a clearly defined naming convention? Are you sure that you have not any conflict RPD, app-roles and web catalog?
Of course, in theory you can merge your own content into the OLIVE one (don't do the opposite because OLIVIER is probably bigger than your own content and you would have more chance to break OBIA with a debugging complex to solve by report may break your and you will be able to fix it easily).
Do not expect to do in half an hour, probably need you some time to make and test things.
-
RB replaces existing report lines
When a footer is the only thing that will be printed on the next page - nothing more is - instead of print on the next page, RB is the footer to print on the same page and overwrite the text that is already there. Everyone knows this and is there a work around or setting that will correct? Thank you!I ran into a similar problem last August. I never got a good answer. Find my old son for more information. I found myself just to remove the cause of multiple columns, I couldn't understand it. If your footer is overwhelming stuff in the first column, so I could not able to help. Just out of curiosity, the problem goes away when you access a presentation of a column? Also, try to go to report > Group Management > change group and set the minimum height for the property Group 8, 5po. That could push the foot to the bottom of the page.
-
Replacement of host existing with the new host/material
We are trying to replace our old 5.0 ESXi hosts that cannot be upgraded to ESXi 5.1 with new hardware that will support ESXi 5.1 and beyond. Existing hosts are members of a cluster of vCenter vCenter has been updated to the latest version We are preinstalled ESXi 5.1 on new hosts and tried to set them up according to the configurations of existing hosts, except for host names and network IPs management.
First of all, are we on track to replace existing hosts?
Second, what are the next steps we would take?
We have read the various messages that seem to follow the steps below, but want to ensure that our incense are applied correctly, we don't miss any major or minor measures, for iSCSI, reusing names existing ESXi hosts and IPs or something else causing the replacement to fail.
1. the vMotion VMs to host existing to another host
2. remove the existing host to vCenter
3. stop the existing host
4. turn on the new host
5. Add the new host to vCenter cluster
6. apply the configuration changes
7. the vMotion VMs to new host
8. follow the same steps in the next new host
We lose all the steps?
Aloha, you were right, this magic file is called state.tgz: VMware KB: locally to restore a configuration of ESXi sauvegardΘ state.tgz
-
Replace the existing values in the BSO
I use a rule of load to load the data from a SQL table. The SQL table has multiple records with the same combination of dimension.
For example, if I have:
Sheet 1: East soda sales 10
Sheet 2: East soda sales 10
When I use "replace existing values", and I question the intersection, I get 10. When I use Add to the existing values, assuming that it was nothing first, I get 20.
I know Aso, you can use the buffer load to records of amount with the same intersection in the cube before loading to the database. My question is, should I use a SQL sum in the State of charge (since I can't create a view that aggregates), or is there some other facility in environmental assessments which allows to replace what is in the cube, but not replacement when the intersection itself appears twice in the same load of data.
Thanks for your time.
Published by: user12268822 on November 29, 2012 12:28If you want to replace what you have in the BSO cube with the sum of the values of the SQL, then you will need to use the money in your SQL query.
-
Create table replaces the existing table in mssql
In a program that allows us to update our sites, we use the function 'create an array' of MS SQL to create missing tables in databases.
Thousands of time we used it, if a table already exists with the same name of the table in the create table MS SQL survey command an error.
In fact, MS SQL documentation indicates that only if you include the optional 'replace' command, will be a replaced existing table.
But today, we used this program on a new host, that we are trying, and the create table command actually did replace an existing table with a new table, delete all the records from the old table.
I'm trying to understand what this would allow the settings at the server level.
This is the code we use:
< CFQUERY NAME = "recipe" DATASOURCE = "recipe" dbtype = "ODBC" username = "" #ruser # "password =" #rPASS #">"
Create table recipecats)
RecipecatID int IDENTITY(1, 1) NOT NULL PRIMARY KEY,
recipecatdescription NVARCHAR (50) NULL)
< / cfquery >Are you sure that this is not just to create another table with the same name, but one
different owner?I saw the strangeness (it's probably just weird for me because I am ignorant)
of what is happening), I can READ a table owned by another user without
calling the name of the table with its owner, and when I go to CREATE a table
of the same name, it is actually created as my current user and subsequently when
you ask the name of the full table, I get the results of one, is not new
the former. If I'm right in the name of the table, I can ask both/either. Kind
way similar CF hunting around different scopes when you aren't eligible one
reference to a variable.Also, your code should probably be testing to see if the table exists
before you try to create it anyway. "Just try and catch.
"If it errors" is not considered as 'test' if there is--
Adam
Maybe you are looking for
-
Is led and leads engine is part of Firefox
It is software that I didn't know had been installed on my computer (or when), and I fear that it is malware. If it's a legitimate software so what use is it, and why I didn't ask if I wanted to install it?
-
Satellite A500-132 - FN key does not work since the update to Windows 7
32-bit system, no driver I can find. What can I do? Thnx
-
Backlight Satellite L500 PSLJ0A - 01 K 013 automatically loses its power
Hi, in these last days the screen on my laptop lost power automatically. I can still (albeit vaguely) see the desktop in the background when this happens. What confuses me, is that if I close the Notepad and then re - open, the screen lights up again
-
Security 0176 - the system has been tampered with
The machine is therefore a T40. He had no no password for at least the 2 years ive had it. The main battery was bad and the cmos battery died recently (id assume bad main battery helped along). After replacing the cmos battery (tested with v-meter an
-
Will be shooting the camera any way hurt Sun Peaks - e.g. to burn the sensor?
Will be shooting the camera any way hurt Sun Peaks - e.g. to burn the sensor?