Restart from error checking. 0x1000008E (0xc0000005, 0xbeedfcff, 0xa8588374, 0x00000000)
Hello
Hello
Follow these steps and check if they help.
Disable automatic reboot to avoid unwanted restarts on system failure.
b. now, use the arrow keys, select Disable automatic restart in case of system error and press ENTER.
Note: When the diagnosis is complete, don't forget to reset your computer to normal startup.
Step 3:
Update your display drivers and see if that helps.
http://support.Microsoft.com/kb/283658
Tags: Windows
Similar Questions
-
Dimension E521 win xp; stop: 0x1000008e (0xc0000005 0xf757bc21 0xb85dfbb0 0x00000000)
My original/factory disk hard get burn, gone, finito, died on my, so I I buy all new hard drive, loaded with every drive him come with the pc, everything was looking fine until the blue screen appears.
and now, at this point one haven't a clue what driver do that!
so far I did step by step each unique method the I get this forum and because of that I'm updating some of the drivers, but UNFORTUNATELY I still have the blue screen!
In the lines below, you will find all the accidents I n up to now, I hope that someone my give some news of how to solve this problem. :Mini082911 - 01.dmp KERNEL_MODE_EXCEPTION_NOT_HANDLED 0x1000008e 0xc0000005 0xf757bc21 0xb85dfbb0 29/08/2011-21:33:12 0 x 00000000 stdriver32.sys stdriver32.sys + 4c21 stdriver.sys stdriver.sys NCH Software 1.13:14:30:54 32-bit stdriver32.sys + 4c21 stdriver32.sys + 1815 stdriver32.sys + 680b ntoskrnl.exe + 1819f C:\WINDOWS\Minidump\Mini082911-01.dmp 2 15 2600 90 112
Mini082711 - 07.dmp 27/08/2011 19:08:03 KERNEL_MODE_EXCEPTION_NOT_HANDLED 0x1000008e 0xc0000005 0xf752bc21 0xb8137bb0 0 x 00000000 stdriver32.sys stdriver32.sys + 4c21 stdriver.sys stdriver.sys NCH Software 1.13:14:30:54 32-bit stdriver32.sys + 4c21 stdriver32.sys + 1815 stdriver32.sys + 680b ntoskrnl.exe + 1819f C:\WINDOWS\Minidump\Mini082711-07.dmp 2 15 2600 90 112
Mini082711 - 06.dmp 27/08/2011-15:26:42 KERNEL_MODE_EXCEPTION_NOT_HANDLED 0x1000008e 0xc0000005 0xf76ebc21 0xb8087bb0 0 x 00000000 stdriver32.sys stdriver32.sys + 4c21 stdriver.sys stdriver.sys NCH Software 1.13:14:30:54 32-bit stdriver32.sys + 4c21 stdriver32.sys + 1815 stdriver32.sys + 680b ntoskrnl.exe + 1819f C:\WINDOWS\Minidump\Mini082711-06.dmp 2 15 2600 90 112
Mini082711 - 05.dmp 27/08/2011-13:55:40 KERNEL_MODE_EXCEPTION_NOT_HANDLED 0x1000008e 0xc0000005 0xf76ebc21 0xb785ebb0 0 x 00000000 stdriver32.sys stdriver32.sys + 4c21 stdriver.sys stdriver.sys NCH Software 1.13:14:30:54 32-bit stdriver32.sys + 4c21 stdriver32.sys + 1815 stdriver32.sys + 680b ntoskrnl.exe + 1819f C:\WINDOWS\Minidump\Mini082711-05.dmp 2 15 2600 90 112
Mini082711 - 04.dmp 27/08/2011-13:39:31 KERNEL_MODE_EXCEPTION_NOT_HANDLED 0x1000008e 0xc0000005 0xf76fbc21 0xb7b1ebb0 0 x 00000000 stdriver32.sys stdriver32.sys + 4c21 stdriver.sys stdriver.sys NCH Software 1.13:14:30:54 32-bit stdriver32.sys + 4c21 stdriver32.sys + 1815 stdriver32.sys + 680b ntoskrnl.exe + 1819f C:\WINDOWS\Minidump\Mini082711-04.dmp 2 15 2600 90 112
Mini082711 - 03.dmp 27/08/2011-12:43:56 KERNEL_MODE_EXCEPTION_NOT_HANDLED 0x1000008e 0xc0000005 0xf7528fc6 0xb877f570 0 x 00000000 stdriver32.sys stdriver32.sys + 1fc6 stdriver.sys stdriver.sys NCH Software 1.13:14:30:54 32-bit stdriver32.sys + 1fc6 stdriver32.sys + 6767 ntoskrnl.exe + 1819f sysaudio.sys + 2c75 C:\WINDOWS\Minidump\Mini082711-03.dmp 2 15 2600 90 112
Mini082711 - 02.dmp 27/08/2011-12:30:51 KERNEL_MODE_EXCEPTION_NOT_HANDLED 0x1000008e 0xc0000005 0xf752bc21 0xb8607bb0 0 x 00000000 stdriver32.sys stdriver32.sys + 4c21 stdriver.sys stdriver.sys NCH Software 1.13:14:30:54 32-bit stdriver32.sys + 4c21 stdriver32.sys + 1815 stdriver32.sys + 680b ntoskrnl.exe + 1819f C:\WINDOWS\Minidump\Mini082711-02.dmp 2 15 2600 90 112
Mini082711 - 01.dmp 27/08/2011 11:59:56 KERNEL_MODE_EXCEPTION_NOT_HANDLED 0x1000008e 0xc0000005 0xf7598fc6 0xf7686570 0 x 00000000 stdriver32.sys stdriver32.sys + 1fc6 stdriver.sys stdriver.sys NCH Software 1.13:14:30:54 32-bit stdriver32.sys + 1fc6 stdriver32.sys + 6767 ntoskrnl.exe + 1819f sysaudio.sys + 2c75 C:\WINDOWS\Minidump\Mini082711-01.dmp 2 15 2600 90 112
Mini082611 - 02.dmp 27/08/2011-01:51:14 KERNEL_MODE_EXCEPTION_NOT_HANDLED 0x1000008e 0xc0000005 0xf751bc21 0xb79e6bb0 0 x 00000000 stdriver32.sys stdriver32.sys + 4c21 stdriver.sys stdriver.sys NCH Software 1.13:14:30:54 32-bit stdriver32.sys + 4c21 stdriver32.sys + 1815 stdriver32.sys + 680b ntoskrnl.exe + 1819f C:\WINDOWS\Minidump\Mini082611-02.dmp 2 15 2600 90 112
Mini082611 - 01.dmp 2011-08-26 18:26:50 KERNEL_MODE_EXCEPTION_NOT_HANDLED 0x1000008e 0xc0000005 0xf76fbc21 0xf6254bb0 0 x 00000000 stdriver32.sys stdriver32.sys + 4c21 stdriver.sys stdriver.sys NCH Software 1.13:14:30:54 32-bit stdriver32.sys + 4c21 stdriver32.sys + 1815 stdriver32.sys + 680b ntoskrnl.exe + 1819f C:\WINDOWS\Minidump\Mini082611-01.dmp 2 15 2600 90 112
Mini080711 - 01.dmp 08-07-2011 19:24:55 KERNEL_MODE_EXCEPTION_NOT_HANDLED 0x1000008e 0xc0000005 0xf7518fc6 0xb6e448ac 0 x 00000000 stdriver32.sys stdriver32.sys + 1fc6 stdriver.sys stdriver.sys NCH Software 1.13:14:30:54 32-bit stdriver32.sys + 1fc6 stdriver32.sys + 6767 ntoskrnl.exe + 1819f sysaudio.sys + 218th C:\WINDOWS\Minidump\Mini080711-01.dmp 2 15 2600 90 112
Mini080611 - 06.dmp 06/08/2011-18:34:31 KERNEL_MODE_EXCEPTION_NOT_HANDLED 0x1000008e 0xc0000005 0xf76f8fc6 0xb726c570 0 x 00000000 stdriver32.sys stdriver32.sys + 1fc6 stdriver.sys stdriver.sys NCH Software 1.13:14:30:54 32-bit stdriver32.sys + 1fc6 stdriver32.sys + 6767 ntoskrnl.exe + 1819f sysaudio.sys + 2c75 C:\WINDOWS\Minidump\Mini080611-06.dmp 2 15 2600 90 112
Mini080611 - 05.dmp 06/08/2011-14:21:41 UNEXPECTED_KERNEL_MODE_TRAP 0x0000000d 0x1000007f 0x00000000 0x00000000 0 x 00000000 stdriver32.sys stdriver32.sys + 4c21 stdriver.sys stdriver.sys NCH Software 1.13:14:30:54 32-bit stdriver32.sys + 4c21 stdriver32.sys + 1815 stdriver32.sys + 680b ntoskrnl.exe + 1819f C:\WINDOWS\Minidump\Mini080611-05.dmp 2 15 2600 90 112
Mini080611 - 04.dmp 06/08/2011-13:21:20 KERNEL_MODE_EXCEPTION_NOT_HANDLED 0x1000008e 0xc0000005 0xf750bc21 0xb9ad6bb0 0 x 00000000 stdriver32.sys stdriver32.sys + 4c21 stdriver.sys stdriver.sys NCH Software 1.13:14:30:54 32-bit stdriver32.sys + 4c21 stdriver32.sys + 1815 stdriver32.sys + 680b ntoskrnl.exe + 1819f C:\WINDOWS\Minidump\Mini080611-04.dmp 2 15 2600 90 112
Mini080611 - 03.dmp 06/08/2011-12:49:28 KERNEL_MODE_EXCEPTION_NOT_HANDLED 0x1000008e 0xc0000005 0xf751bc21 0xb9a66bb0 0 x 00000000 stdriver32.sys stdriver32.sys + 4c21 stdriver.sys stdriver.sys NCH Software 1.13:14:30:54 32-bit stdriver32.sys + 4c21 stdriver32.sys + 1815 stdriver32.sys + 680b ntoskrnl.exe + 1819f C:\WINDOWS\Minidump\Mini080611-03.dmp 2 15 2600 90 112
Mini080611 - 02.dmp 06/08/2011-12:38:58 KERNEL_MODE_EXCEPTION_NOT_HANDLED 0x1000008e 0xc0000005 0xf7518fc6 0xb9626570 0 x 00000000 stdriver32.sys stdriver32.sys + 1fc6 stdriver.sys stdriver.sys NCH Software 1.13:14:30:54 32-bit stdriver32.sys + 1fc6 stdriver32.sys + 6767 ntoskrnl.exe + 1819f sysaudio.sys + 2c75 C:\WINDOWS\Minidump\Mini080611-02.dmp 2 15 2600 90 112
Mini080611 - 01.dmp KERNEL_MODE_EXCEPTION_NOT_HANDLED 0x1000008e 0xc0000005 0xf751bc21 0xb9aaebb0 06/08/2011-12:02:22 0 x 00000000 stdriver32.sys stdriver32.sys + 4c21 stdriver.sys stdriver.sys NCH Software 1.13:14:30:54 32-bit stdriver32.sys + 4c21 stdriver32.sys + 1815 stdriver32.sys + 680b ntoskrnl.exe + 1819f C:\WINDOWS\Minidump\Mini080611-01.dmp 2 15 2600 90 112
Mini080511 - 01.dmp 06/08/2011-12:45:58 AM KERNEL_MODE_EXCEPTION_NOT_HANDLED 0x1000008e 0xc0000005 0xf753bc21 0xb975ebb0 0 x 00000000 stdriver32.sys stdriver32.sys + 4c21 stdriver.sys stdriver.sys NCH Software 1.13:14:30:54 32-bit stdriver32.sys + 4c21 stdriver32.sys + 1815 stdriver32.sys + 680b ntoskrnl.exe + 1819f C:\WINDOWS\Minidump\Mini080511-01.dmp 2 15 2600 90 112System: Microsoft Windows XP
Media center Edition
Version 2002
Service Pack 3
Computer: AMD Athlon (TM) 64 x 2 Dual
Processor Core 3800 +.
2.00 GHz, 1.00 GB of RAM
Physical address extensionP.D. Not to mention that I need to "restore point", or something like that, remember, «MY FACTORY HARD DRIVE IS GONE»
Thank you.Hello
1. when exactly you get the blue screen error?
2 have you tried the steps by Joel S?
3. are you able to boot to the desktop with success?
4. the problem persists in safe mode?
Read the following article which is useful.
Using Driver Verifier to identify issues with Windows drivers for users advanced
-
Blue screen and error code: 0x0000008E (0xC0000005, 0x8243BA8D, 0xE3452BB4, 0x00000000) _
I get the above error message and bluescreen when the computer is just sitting idle does nothing. Usually, it's when the internet is open, but not surf. Can someone help me understand this. The graphics card is an Intel 82945 G express shipset family and I checked to see if it is up-to-date and the pilot said he is up to date.
Any help?
Hello
Have you checked Site system manufacturer (manufacturer of custom systems motherboard), then
Intel downloads?After checking the system manufacturer's Site
Intel - Downloads - graphical value and then the other parameters as needed.
http://Downloadcenter.Intel.com/===========================================================
Check this thread for more information using BlueScreenView, MyEventViewer and other methods
to troubleshoot the BlueScreens - top 3 responses (+ 1 other).We can analyze the minidumps if make you it available to the SkyDrive or another file
sharing sites.ZIP or download the content of the C:\Windows\minidump
Use SkyDrive to upload collected files
http://social.technet.Microsoft.com/forums/en-us/w7itproui/thread/4fc10639-02dB-4665-993a-08d865088d65--------------------------------------------------------------------------------------------------------------
Two main causes of this blue screen video drivers and BIOS - check with the system manufacturer
Site for graphics (Video) card and BIOS, then on site of the manufacturer of the device for the last video. It may be
other pilots to check there. Disable the installation of self as those who are older and if
Updates Windows suggests a pilot just HIDE. Antivirus is another possibility.See methods of update driver generic in the next message.
BCCode: 8th 0x0000008E is the same as 0x1000008E
Cause
Bug KERNEL_MODE_EXCEPTION_NOT_HANDLED control is a very common bug control. To interpret it, you must identify which exception has been generated.
Common exception codes are:
- 0xc0000005: STATUS_ACCESS_VIOLATION indicates that a memory access violation has occurred.
Solve the problem
If you do not have to debug this problem, you must use certain basic troubleshooting techniques:
- Make sure you have enough disk space.
- If a driver is identified in the bug check message, disable the driver or check with the manufacturer for driver updates.
- Try changing video cards.
- Check with your hardware vendor for updates to the BIOS.
- Disable the BIOS memory options such as implementing caching or shading.
If you plan to debug this problem, you may find it difficult to get a stack trace. Parameter 2 (the address of the exception) should identify the driver or function that caused the problem.
If you do not know the specific cause of the exception, consider the following:
- Hardware incompatibility. Ensure that all new equipment installed is listed in the list of the products tested Microsoft Windows market.
- Service driver or defective peripheral system. A chauffeur service or defective peripheral system could be responsible for this error. The hardware problems, such as BIOS incompatibilities, conflicts of memory and IRQ conflicts can also generate this error.
If the verification of the message bug list a driver by name, disable or remove that driver. In addition, disable or remove drivers or services that have been recently added. If the error occurs during the startup sequence and the system partition is formatted with the NTFS file system, you may be able to use Safe Mode to rename or to delete the faulty driver. If the driver is used as part of the start-up procedure of the system Safe Mode, you must start the computer by using the Recovery Console to access the file.
If the problem is associated with Win32k.sys, the source of the error may be a third-party remote control program. If this software is installed, you can remove the system startup service using the recovery and then Console by removing the offending system service file.
Check the system log in Event Viewer for additional error messages that might help identify the device or driver responsible for control of bug 0x1E. You can disable the cache in memory of the BIOS to try to resolve the error. You must also run the diagnostics of material, especially the scanner memory, which provides the manufacturer of the system. For more information about these procedures, see the manual of your computer.
The error that generates this message may occur after the first reboot during Windows Setup, or after installation is complete. A possible cause of the error is lack of disk space for installation and the system BIOS incompatibilities. For any problems during the installation of Windows that are associated with lack of disk space, reduce the number of files on the hard disk drive target. Search and delete temporary files that you do not have to have, files hidden Internet, application backup files and files saved.chk, which contain fragments of files on disk scans. You can also use an another hard disk drive with more free space for the installation.
You can solve the problems of BIOS by upgrading the version of the system BIOS
BCCode: 8th 0x0000008E is the same as 0x1000008E<-- read="" this="">
* 1151.html? order = date http://www.faultwire.com/solutions-fatal_error/kernel-mode-exception-not-HANDLED-0x0000008E-=============================================
Look in the Event Viewer to see if something is reported on those.
http://www.computerperformance.co.UK/Vista/vista_event_viewer.htmMyEventViewer - free - a simple alternative in the standard Windows Event Viewer.
TIP - Options - Advanced filter allows you to see a period of time instead of the entire file.
http://www.NirSoft.NET/utils/my_event_viewer.html-------------------------------------------------------------------------
Also this, so you can see the probable bluescreens. (If necessary)
Windows Vista restarts automatically if your computer encounters an error that requires him to plant.
http://www.winvistatips.com/disable-automatic-restart-T84.html-------------------------------------------------------------------------
It comes to my convenience store generic bluescreen:
Here are a few ways to possibly fix the blue screen issue. If you could give the info to blue screen
This would help. Such as ITC and 4 others entered at the bottom left. And another error
information such as the STOP codes and info like IRQL_NOT_LESS_OR_EQUAL or PAGE_FAULT_IN_NONPAGED_AREA and similar messages.As examples:
BCCode: 116
BCP1: 87BC9510
BCP2: 8C013D80
BCP3: 00000000
BCP4: 00000002or in this format:
Stop: 0 x 00000000 (oxoooooooo oxoooooooo oxoooooooo oxooooooooo)
Tcpip.sys - address blocking 0 x 0 00000000 000000000 DateStamp 0 x 000000000It is an excellent tool for displaying the blue screen error information
BlueScreenView scans all your minidump files created during 'blue screen of death '.
http://www.NirSoft.NET/utils/blue_screen_view.html
hangs and displays information about all accidents of a table - freeBlueScreens many are caused by old or damaged, in particular the video drivers drivers however
There are other causes.You can do without if needed fail or the Vista DVD or recovery command prompt mode
Options if your system was installed by the manufacturer.This tells you how to access the System Recovery Options and/or a Vista DVD
http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspxYou can try a system restore to a point before the problem started when one exists.
How to make a Vista system restore
http://www.Vistax64.com/tutorials/76905-System-Restore-how.html-------------------------------------------------------------------------
Start - type this into the search-> find COMMAND to top box and RIGHT CLICK-
RUN AS ADMINEnter this at the command prompt - sfc/scannow
How to analyze the log file entries that the Microsoft Windows Resource Checker
(SFC.exe) program generates in Windows Vista cbs.log
http://support.Microsoft.com/kb/928228The log can give you the answer if there is a corrupted driver. (Says not all possible
driver problems).Also run CheckDisk, so we cannot exclude as much as possible of the corruption.
How to run the check disk at startup in Vista
http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html-------------------------------------------------------------------------
Often drivers up-to-date will help, usually video, sound, network card (NIC), WiFi, part 3
keyboard and mouse, as well as of other major device drivers.Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htmHow to install a device driver in Vista Device Manager
http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.htmlHow to disable automatic driver Installation in Windows Vista - drivers
http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx-------------------------------------------------------------------------
How to fix BlueScreen (STOP) errors that cause Windows Vista to shut down or restart
quit unexpectedly
http://support.Microsoft.com/kb/958233Troubleshooting, STOP error blue screen Vista
http://www.chicagotech.NET/Vista/vistabluescreen.htmUnderstanding and decoding BSOD (blue screen of death) Messages
http://www.Taranfx.com/blog/?p=692Windows - troubleshooting blue screen errors
http://KB.wisc.edu/page.php?id=7033-------------------------------------------------------------------------
In some cases, it may be necessary.
The Options or Vista recovery disk Startup Repair
How to do a startup repair
http://www.Vistax64.com/tutorials/91467-startup-repair.htmlThis tells you how to access the System Recovery Options and/or a Vista DVD
http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspxI hope this helps.
Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="" -="" mark="" twain="" said="" it="">
-
verification of error 0x0000008e (0xc0000005, 0x00000001e, 0xad6c6efc, 0x00000000) to start Windows.
Original title: error checking 0x0000008e (0xc0000005, 0x00000001e, 0xad6c6efc, 0x00000000)
I'm bugcheck force a reboot on startup...
error is: error checking 0x0000008e (0xc0000005, 0x00000001e, 0xad6c6efc, 0x00000000)
What is the problem and how can I fix?
Hi Hal_Y,
You are able to start correctly on the desktop?
If you are able to boot to the desktop, you can follow this link & check if the problem persists:
You receive a random "0x0000008E" error message on a blue screen in Windows XP
Hope the helps of information.
-
The system has recovered from a serious error. Error checking.
IBM ThinkCentre. Windows XP Pro
My computer restarted on its own several times the last 2 weeks. I have the following error after logging in:
The system has recovered from a serious error. A log of this error was created. Please tell this problem to Microsoft.
Error signature
BCCode: 100007f BCP1: 00000008 BCP2: 80042000 BCP3: 00000000 BCP4: 00000000 OSVer: 5_1_2600 SP: 3_0 product: 256_1The following files will be included in this error report:
C:\DOCUME~1\JASOND~1.IND\LOCALS~1\Temp\WER9b18.dir00\Mini033110-01.dmp
C:\DOCUME~1\JASOND~1.IND\LOCALS~1\Temp\WER9b18.dir00\sysdata. XMLError log
Event type: Information
Event source: Save Dump
Event category: no
Event ID: 1001
Date: 31/03/2010
Duration: 04:00:35
Description:
The computer was restarted after a bugcheck. The bugcheck was: 0x1000007f (0 x 80042000, 0x00000000, 0x00000008, 0x00000000). A dump was saved in the: C:\WINDOWS\Minidump\Mini033110-01.dmp.Each of the last depressed, ibmfilter.sys is involved in error checking.
Still, the nature of the kernel stack overflow is that all these filter drivers may contribute to the problem. Most of the attached drivers are Symantec drivers, it seems reasonable that remove the Symantec software would certainly take care of the issue. However, remove the Chuck ibmfilter can free enough battery to avoid the problem as well. Or update the drivers involved could also have an impact, if changes have been made to account for this type of situation.
-
I removed the check mark to "Accept cookies from sites" in the Privacy tab, but when I restart Firefox the check mark is back! This problem started with version 3.6 and so I upgraded to version 5, but the problem remains. Any suggestions?
Preferences are not saved
https://support.Mozilla.com/en-us/KB/preferences%20are%20not%20saved
Check and tell if its working.
-
A problem is preventing Windows from accurately checking the license for this computer. Error code: 0 x 80090006
Error comes when you try to connect.
-able to login in safe mode
-J' tried regsvr32 regwizc.dll, regsvr32 licdll.dll from start-> run
-Tried system restore
Any other solution?
Hello
- What were the changes made before the issue started?
You can check this link:You may receive error code 0 x 80004005 and other error codes when you try to start a Windows XP-based computer -
When you try to download a book from my library, I get an error message: error, check activation. What should I now please?
Hi 7Philip1116,
Using the Adobe Digital Editions software? If so, I suspect that you meet one of the known activation errors. Often, deactivation and reactivation (cmd-shift-D on Mac) or ctrl-shift-D Windows will solve the problem. Instructions step by step, but also other possible solutions are available here: Errors of Activation
If it is not a question of Digital Editions or if the advice above do not resolve your problem, please respond with a few more details so that we can better solve the problems. What software Adobe are you use and the type of device/operating system? Can you provide a screenshot of the error? The specified item was not found.
Best,
Del
-
Lightroom starts but then I get "error reading the preview cache. LR needs to stop smoking. Will try next time it starts. I restart from scratch and the same thing happens. Help please!
In the same folder that your catalog file is stored in, there is a subfolder whose name ends with Previews.LRDATA. Delete this subfolder whose name ends with Previews.LRDATA. Do not remove anything else.
-
Error Stop: 0X0000008E (0XC0000005, 0X820371A7, 0X9F10E91C, 0 x 0000000).
I have error Stop: 0X0000008E (0XC0000005, 0X820371A7, 0X9F10E91C, 0 x 0000000). I did the F9 Diagnostics and no error found. Also, I tried to remove the DVD and replace the video card, but no improvement. However, Windows starts normally in SafeMode only. Thanks for supporting.
Product ID: 89578-OEM-7332157-00061
Hello
Specifying your version of Windows and other information would help help us to you.
How to ask a question
http://support.Microsoft.com/kb/555375-----------------------------------------------------------------------------------------------------------------
Check this thread for more information using BlueScreenView, MyEventViewer and other methods
to troubleshoot the BlueScreens - top 3 responses (+ 1 other).We can analyze the minidumps if make you it available to the SkyDrive or another file
sharing sites.ZIP or download the content of the C:\Windows\minidump
Use SkyDrive to upload collected files.
http://social.technet.Microsoft.com/forums/en-us/w7itproui/thread/4fc10639-02dB-4665-993a-08d865088d65===============================================================
BCCode: 8th 0x0000008E is the same as 0x1000008ETwo main causes of these blue screen video drivers and BIOS - check with the system manufacturer
Site for graphics (Video) card and BIOS, then on site of the manufacturer of the device for the last video. It may be
other pilots to check there. Disable the installation of self as those who are older and if
Updates Windows suggests a pilot just HIDE. Antivirus is another possibility.See the methods of update driver generic and verify the implementation of driver verifier in the next
Message.BCCode: 8th 0x0000008E is the same as 0x1000008E
Cause
Bug KERNEL_MODE_EXCEPTION_NOT_HANDLED control is a very common bug control. To interpret it, you must identify which exception has been generated.
Common exception codes are:
0 x 80000002: STATUS_DATATYPE_MISALIGNMENT indicates that an unaligned data reference was encountered.
0 x 80000003: STATUS_BREAKPOINT indicates that a breakpoint or ASSERTION was met when no kernel debugger was attached to the system.
0xc0000005: STATUS_ACCESS_VIOLATION indicates that a memory access violation has occurred.
Solve the problem
If you do not have to debug this problem, you must use certain basic troubleshooting techniques:
Make sure you have enough disk space.
- If a driver is identified in the bug check message, disable the driver or check with the manufacturer for driver updates.
- Try changing video cards.
- Check with your hardware vendor for updates to the BIOS.
- Disable the BIOS memory options such as implementing caching or shading.
If you plan to debug this problem, you may find it difficult to get a stack trace. Parameter 2 (the address of the exception) should identify the driver or function that caused the problem.
If you do not know the specific cause of the exception, consider the following:
- Hardware incompatibility. Ensure that all new equipment installed is listed in the list of the products tested Microsoft Windows market.
- Service driver or defective peripheral system. A chauffeur service or defective peripheral system could be responsible for this error. The hardware problems, such as BIOS incompatibilities, conflicts of memory and IRQ conflicts can also generate this error.
If the verification of the message bug list a driver by name, disable or remove that driver. In addition, disable or remove drivers or services that have been recently added. If the error occurs during the startup sequence and the system partition is formatted with the NTFS file system, you may be able to use Safe Mode to rename or to delete the faulty driver. If the driver is used as part of the start-up procedure of the system Safe Mode, you must start the computer by using the Recovery Console to access the file.
If the problem is associated with Win32k.sys, the source of the error may be a third-party remote control program. If this software is installed, you can remove the system startup service using the recovery and then Console by removing the offending system service file.
Check the system log in Event Viewer for additional error messages that might help identify the device or driver responsible for control of bug 0x1E. You can disable the cache in memory of the BIOS to try to resolve the error. You must also run the diagnostics of material, especially the scanner memory, which provides the manufacturer of the system. For more information about these procedures, see the manual of your computer.
The error that generates this message may occur after the first reboot during Windows Setup, or after installation is complete. A possible cause of the error is lack of disk space for installation and the system BIOS incompatibilities. For any problems during the installation of Windows that are associated with lack of disk space, reduce the number of files on the hard disk drive target. Search and delete temporary files that you do not have to have, files hidden Internet, application backup files and files saved.chk, which contain fragments of files on disk scans. You can also use an another hard disk drive with more free space for the installation.
You can solve the problems of BIOS by upgrading the version of the system BIOS
BCCode: 8th 0x0000008E is the same as 0x1000008E<-- read="" this="">
* 1151.html? order = date http://www.faultwire.com/solutions-fatal_error/kernel-mode-exception-not-HANDLED-0x0000008E-=============================================
Look in the Event Viewer to see if something is reported on those.
http://www.computerperformance.co.UK/Vista/vista_event_viewer.htmMyEventViewer - free - a simple alternative in the standard Windows Event Viewer.
TIP - Options - Advanced filter allows you to see a period of time instead of the entire file.
http://www.NirSoft.NET/utils/my_event_viewer.html-------------------------------------------------------------------------
Also this, so you can see the probable bluescreens.
Windows Vista restarts automatically if your computer encounters an error that requires him to plant.
http://www.winvistatips.com/disable-automatic-restart-T84.html-------------------------------------------------------------------------
Here are a few ways to possibly fix the blue screen issue. If you could give the blue screen
info that would help. Such as ITC and 4 others entered at the bottom left. And all others
error information such as codes of STOP and info like IRQL_NOT_LESS_OR_EQUAL or PAGE_FAULT_IN_NONPAGED_AREA and similar messages.As examples:
BCCode: 116
BCP1: 87BC9510
BCP2: 8C013D80
BCP3: 00000000
BCP4: 00000002or in this format:
Stop: 0 x 00000000 (oxoooooooo oxoooooooo oxoooooooo oxooooooooo)
Tcpip.sys - address blocking 0 x 0 00000000 000000000 DateStamp 0 x 000000000It is an excellent tool for displaying the blue screen error information
BlueScreenView scans all your minidump files created during 'blue screen of death '.
hangs and displays information about all accidents of a table - free
http://www.NirSoft.NET/utils/blue_screen_view.htmlBlueScreens many are caused by old or damaged, in particular the video drivers drivers however
There are other causes.You can do mode if necessary safe or the Vista DVD command prompt or
Options recovery if your system is installed by the manufacturer.How to start on the System Recovery Options in Windows 7
http://www.SevenForums.com/tutorials/668-system-recovery-options.htmlYou can try a system restore to a point before the problem started when one exists.
How to do a system restore in Windows 7
http://www.SevenForums.com/tutorials/700-system-restore.html-------------------------------------------------------------------------
Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN
Enter this at the command prompt - sfc/scannow
How to fix the system files of Windows 7 with the System File Checker
http://www.SevenForums.com/tutorials/1538-SFC-SCANNOW-Command-System-File-Checker.htmlHow to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
generates cbs.log Windows Vista (and Windows 7)
http://support.Microsoft.com/kb/928228The log can give you the answer if there is a corrupted driver. (Says not all possible
driver problems).Also run CheckDisk, so we cannot exclude as much as possible of the corruption.
How to run the check disk at startup in Windows 7
http://www.SevenForums.com/tutorials/433-disk-check.html-------------------------------------------------------------------------
Often drivers up-to-date will help, usually video, sound, network card (NIC), WiFi, part 3
keyboard and mouse, as well as of other major device drivers.Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htmInstallation and update of drivers to 7
http://www.SevenForums.com/tutorials/43216-installing-updating-drivers-7-a.htmlHow to disable automatic driver Installation in Windows Vista - drivers
http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx-------------------------------------------------------------------------
How to fix BlueScreen (STOP) errors that cause Windows Vista to shut down or restart
quit unexpectedly
http://support.Microsoft.com/kb/958233Troubleshooting Vista Blue Screen, error of JUDGMENT (and Windows 7)
http://www.chicagotech.NET/Vista/vistabluescreen.htmUnderstanding and decoding BSOD (blue screen of death) Messages
http://www.Taranfx.com/blog/?p=692Windows - troubleshooting blue screen errors
http://KB.wisc.edu/page.php?id=7033-------------------------------------------------------------------------
In some cases, it may be necessary.
Startup Options recovery or Windows 7 disk repair
How to run a startup repair in Windows 7
http://www.SevenForums.com/tutorials/681-startup-repair.htmlHow to start on the System Recovery Options in Windows 7
http://www.SevenForums.com/tutorials/668-system-recovery-options.htmlHow to create a Windows 7 system repair disc
http://www.SevenForums.com/tutorials/2083-system-repair-disc-create.htmlHow to do a repair installation to repair Windows 7
http://www.SevenForums.com/tutorials/3413-repair-install.htmlI hope this helps.
Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="" -="" mark="" twain="" said="" it="">
-
An error occurred during the update error checking new Code 80072EFE
An error occurred during the update error checking new Code 80072EFE
error 80072EFE infected by a root
Launch tdsskiller to find any rootkids, download and run from here
http://support.Kaspersky.com/downloads/utils/TDSSKiller.exe
your computer will restart automatelly and start up. Then run the updates.
-
Drive external DRIVE not detected (2 PCs), after turning off the PC during the error checking
I ran properties/tools/error-check on a (regularly used to back up this PC XP) external HARD drive. After 2 days, error checking was still running and not even 1/3 way 4th Phase but I need PC. It was not possible to stop "Error Check" from the dialog box then I tried Task Manager/Applications, which said that nothing worked, so I turned off the PC.
When I restarted the PC, external HARD disk was not in my computer. Control Panel of configuration/addition does not see it no more. However, when I plug / unplug the station. HDD USB cable, the computer makes a noise and is also recognized in "Device safely Shut Down" as a USB storage device mass (but no drive letter). I tried to start/run/Cmd/Diskpart/List Disk and it is not listed.
NB. I checked the post. HARD drive on a Linux PC, which also does not detect not, then it is certainly the post. Drive HARD, not the XP PC.
Can offer you any advice?
Hello
· What is the number and the model of the hard drive?
As you mentioned that the issue isn't with the operating system but with the drive hard, for better support I suggest you to contact the manufacturer of the hard drive.
You can also get in touch with any local technician who can help you with the same.
-
Where can I find a 'disk error checking Tool '.
I received an error when I tried to us MS Backup that the backup was unsuccessful, but it does not give me an error as shown in the threads (0 x 81000002). He has just declared that there is a corrupted file and I should use a 'disk error checking Tool '. My question is, where can I find it? I am running Vista, service pack 2. Appreciate any help you can offer.
Dennis Zinke
Just run chkdsk from the command prompt
Start > run > CMD
Chkdsk /f
Type 'Y' and press ENTER when he says that he cannot do that now because the drive is in use. Then restart your computer and it will check your drive and try to fix the errors. Randall
-
HOW CAN I FIX A SCREEN BLUE, WITH STOP ERROR CODE: 0X0000007E (0XC0000005, 0X89F24OAE, 0X8A953BA0, 0X8A95389C)
Hello
Please do not type in capital letters because it's difficult to read and considered to be shouting.
---------------------------------------------------------------------------------------------------
Check this thread for more information using BlueScreenView, MyEventViewer and other methods
to troubleshoot the BlueScreens - top 3 responses (+ 1 other).We can analyze the minidumps if make you it available to the SkyDrive or another file
sharing sites.ZIP or download the content of the C:\Windows\minidump
Use SkyDrive download collected files and after shot/screenshot.
http://social.technet.Microsoft.com/forums/en-us/w7itproui/thread/4fc10639-02dB-4665-993a-08d865088d65-------------------------------------------------------------------------
Also this, so you can see the probable bluescreens.
Windows Vista restarts automatically if your computer encounters an error that requires him to plant.
(also Windows 7)
http://www.winvistatips.com/disable-automatic-restart-T84.html===========================================================
The system has RAID? If so, it's also very suspicious.
This error is usually a driver problem and display adapter (video) driver is the most suspicious if she
may be others. Antivirus/antispyware/security programs, equipment (heat) and major software problems
can also cause the error. When you get to the section of the driver to use the Troubleshoot utility my generic
methods in the next message and then return to the if necessary troubleshooting tool.Have you recently added hardware or drivers updated? Don't forget to look in Control Panel - Windows
Updates to see if all drivers have been updated it. Other donor opportunities include the antivirus/anti-
spyware/security programs.When you get to the pilot and sections of the memory of the troubleshooter check the following message to
update drivers and memory test and then return to the troubleshooter if necessary.BCCode: 7F 0x0000007E which is also 0x1000007E
Cause
SYSTEM_THREAD_EXCEPTION_NOT_HANDLED bug control is a very common bug control. TO
interpret, you must identify which exception has been generated.Common exception codes are:
- 0xc0000005: STATUS_ACCESS_VIOLATION indicates a memory access violation has occurred.
For a complete list of exception codes, see the Ntstatus.h file located in theinc directory
the Microsoft Windows Driver Kit (WDK).Solve the problem
If you do not have to debug this problem, you must use certain basic troubleshooting techniques.
- Make sure you have enough disk space.
- If a driver is identified in the bug check message, disable the driver or check with the
- Reference of the manufacturer for driver updates.
- Try changing video cards.
- Check with your hardware vendor for updates to the BIOS.
- Disable the BIOS memory options such as implementing caching or shading.
If you plan to debug this problem, you may find it difficult to get a stack trace. Parameter 2
(the address of the exception) must identify the driver or function that caused the problem.If the exception code 0 x 80000003 occurs, a hard-coded breakpoint or assertion was hit, but the system
has been launched with the /nodebug. switch. This problem should occur infrequently. If it occurs repeatedly,
Make sure that a kernel debugger is connected and the system is booted with the Switch/DEBUG .In case of exception code 0 x 80000002, the trap frame provides additional information.
If you do not know the specific cause of the exception, consider the following questions:
- Hardware incompatibility. Make sure all new hardware that is installed is listed in the
- List of Microsoft Windows Marketplace tested products.
- Service driver or defective peripheral system. A service driver or defective peripheral system can be
- responsible for this error. Hardware problems, such as the incompatibilities of the BIOS, memory, conflicts
- and IRQ conflicts can also generate this error.
If a driver is listed by name in the bug check message, disable or remove that driver. Disable
or remove drivers or services that have been recently added. If the error occurs during startup
sequence and the system partition is formatted with the NTFS file system, you may be able to use safe
Mode to rename or to delete the faulty driver. If the driver is used as part of the system startup procedure
in Safe Mode, you must start the computer by using the Recovery Console to access the file.If the problem is associated with Win32k.sys, the source of the error may be a third remote
control program. If this software is installed, you can remove the boot of the computer service
by using the Recovery Console, and then by removing the offending system service file.Check the system log in Event Viewer for additional error messages that might help identify the
device or the driver that generated the bug check 0x7E.You can also disable memory cache BIOS may try to resolve the error. You should also
Run the diagnostics of material, especially the scanner memory, which provides the manufacturer of the system.
For more information about these procedures, see the manual of your computer.The error that generates this message may occur after the first reboot during Windows Setup, or
Once the installation is complete. A possible cause of the error is lack of disk space for installation and system
BIOS incompatibilities. For problems during the installation of Windows that are associated with the absence of disc
space, reduce the number of files on the disk drive hard target. Find and delete any temporary
the files that you do not have to have files hidden Internet, backup application and.chkfiles files that
contain fragments of file saved to disk scans. You can also use another hard drive with more drive
free space for the installation. You can solve the problems of BIOS by upgrading the version of the system BIOS.BCCode: 7F 0x00000007E who is also a 0x1000007E<-- read="" this="">
* 1141.html? order = votes http://www.faultwire.com/solutions-fatal_error/System-thread-exception-not-HANDLED-0x0000007E-----------------------------------------------------------------------------------------------------------------------
Look in the Event Viewer to see if something is reported on those.
http://www.computerperformance.co.UK/Vista/vista_event_viewer.htmMyEventViewer - free - a simple alternative in the standard event viewer
Windows. TIP - Options - Advanced filter allows you to see a time rather
of the entire file.
http://www.NirSoft.NET/utils/my_event_viewer.htmlHere are a few ways to possibly fix the blue screen issue. If you could give the blue screen
info that would help. Such as ITC and 4 others entered at the bottom left. And all others
error information such as codes of STOP and info like IRQL_NOT_LESS_OR_EQUAL or PAGE_FAULT_IN_NONPAGED_AREA and similar messages.As examples:
BCCode: 116
BCP1: 87BC9510
BCP2: 8C013D80
BCP3: 00000000
BCP4: 00000002or in this format:
Stop: 0 x 00000000 (oxoooooooo oxoooooooo oxoooooooo oxooooooooo)
Tcpip.sys - address blocking 0 x 0 00000000 000000000 DateStamp 0 x 000000000It is an excellent tool for displaying the blue screen error information
BlueScreenView scans all your minidump files created during ' blue screen of the.
http://www.NirSoft.NET/utils/blue_screen_view.html
death ' crashes and displays information about all accidents of a table.
FreeBlueScreens many are caused by drivers of old or damaged, in particular the video drivers
However, there are other causes.You can do mode if necessary safe or the Vista DVD command prompt or
Options recovery if your system is installed by the manufacturer.This tells you how to access the System Recovery Options and/or a Vista DVD
http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspxYou can try a system restore to a point before the problem started when one exists.
How to make a Vista system restore
http://www.Vistax64.com/tutorials/76905-System-Restore-how.html-------------------------------------------------------------------------
Start - type this into the search-> find COMMAND to top box and RIGHT CLICK-
RUN AS ADMINEnter this at the command prompt - sfc/scannow
How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe)
program generates in Windows Vista cbs.log
http://support.Microsoft.com/kb/928228The log can give you the answer if there is a corrupted driver. (Does not work
tell all possible driver issues).Also run CheckDisk, so we cannot exclude as much as possible of the corruption.
How to run the check disk at startup in Vista
http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html-------------------------------------------------------------------------
Often drivers up-to-date will help, usually video, sound, network card (NIC), WiFi, part 3
keyboard and mouse, as well as of other major device drivers.Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htmHow to install a device driver in Vista Device Manager
http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.htmlHow to disable automatic driver Installation in Windows Vista - drivers
http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx-------------------------------------------------------------------------
How to fix BlueScreen (STOP) errors that cause Windows Vista to shut down or restart
quit unexpectedly
http://support.Microsoft.com/kb/958233Troubleshooting, STOP error blue screen Vista
http://www.chicagotech.NET/Vista/vistabluescreen.htmUnderstanding and decoding BSOD (blue screen of death) Messages
http://www.Taranfx.com/blog/?p=692Windows - troubleshooting blue screen errors
http://KB.wisc.edu/page.php?id=7033-------------------------------------------------------------------------
In some cases, it may be necessary.
The Options or Vista recovery disk Startup Repair
How to do a startup repair
http://www.Vistax64.com/tutorials/91467-startup-repair.htmlThis tells you how to access the System Recovery Options and/or a Vista DVD
http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspxI hope this helps.
Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="" -="" mark="" twain="" said="" it="">
-
Windows Vista SP2, random BSOD with error checking code 0 x 19
Hi all
I have seemingly random crashes on my old laptop 3 years recently - BSOD with error checking code 0 x 0000019 (0x00000020, 0xe92f4780, 0xe92f48d0, 0x0a2a0440), and BlueScreenView says that accidents are caused by ntkrnlpa.exe and Ntfs.sys. I have absolutely no idea why it happened--unusual does update, none of the material changes & software installations. The system hangs especially after maybe one or two days after starting with some sleep & wake ups inbetween and the only accidents while there are prominent running shows - namely, all the accidents that happened while I was running Firefox. Seconds before the BSoD (shell & all) system simply freezes and does not respond to ctrl + alt + delete, but is still running (as indicated by the fact that once, I forced a power off and after that restart the event log indicates the previous stop at was not planned), then watch the usual BSoD screen.
After doing some googling, I began to suspect that this should be a memory or a hard drive problem, or maybe an overheating causing the two since he not there no significant change of software on my computer recently again issues just appeared without reason. So I cleaned my laptop fan and the heatsink and ensured that the hot air can leave the chassis without being blocked, did some checking of memory with memory auditing Windows - no problems in 5 innings and ran chkdsk on my system partition with all available options - perfectly normal, but the chkdsk has acted quite strangely that check all took about 30 seconds and no normal as the ID information of partition, size etc. that should be there never appeared; is this a normal behavior? or something is wrong with my chkdsk?
I'm still (lol) impatiently waiting for the next crash, not sure whether the problem is still there or not. Meanwhile could you please help me understand what is the problem with my system?
It seems that the disc is the most likely cause. If it is intermittent, it may be difficult to diagnose.
The manufacturer of the laptop provides any diagnosis? Several manufacturers have a key at startup to access the diagnostics.
CHKDSK should last several minutes. There is information about the different ways to run chkdsk here:
http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html
You can try this disc test program:
http://www.Seagate.com/www/en-us/support/downloads/SeaTools/
If the version of WIndows does not find anything. Try to use the version BACK from a CD.
Maybe you are looking for
-
How can I protect some files of the icloud sharing in the sierra?
How can I protect certain files from the desktop to icloud and sharing documents in the sierra? Some of my data is private and I don't want it in the cloud.
-
I want to remove my iTunes balance to change the country from the United States towards my country Jordan
-
double-sided printing HPDeskjet 2542
All ads before you buy, I saw said that the 2542 Deskjet not duplex and this option appears in the menu printing, but he always does it manually - that is asking you to remove the paper and the re - load between the sheets. Advice please? I turn the
-
Where the Manager of power supply for Thinkpad E440 8.1 on windows
Hello, is there any manager of power for thinkpad E440 8.1 on windows, I have already installed the driver for power management since the lenovo support site, but I think I need to install the power manager. is it good? If so, are there no power mana
-
NOR - RT.ini in the cvs-1458RT file
Hello CRIO systems, there is a file named NOR - RT.ini, which can be used to settle the claim of commissioning, set the time zone, etc. It is normally located in the root. Is there a similar file for CVS-1458RT, and if so, where can I find it? Thank