RV042 to AG241V2 VPN static IP to dynamic IP to AG241V2 RV042

Similar Questions

• L2l VPN static to the dynamic with redundancy

  Hi I have IPSEC VPN configured between two Cisco routers.

  a Dyamic, static end head end. and it works like a charm,

  What I want to achieve now is.

  If my head goes down, I want to end Remtoe to connect to NDDN Head end.

  is this possible?

  currently on my side, I have configured this way (partial configuration)

  vpn 10 ipsec-isakmp crypto map

  the value of 8.2x.1x.4 peer

  Set low transformation game

  match address 100

  what I want is if 8.2x.1x.4 is unreachable, VPN must be connected to the second head say 1.1.1.1

  any help would be great.

  Hello Ahmad,

  Yes it is possible.

  You set the primary peer as your default and so the default peer will always prefered.

  http://www.Cisco.com/en/us/docs/iOS/Security/command/reference/sec_s2.html#wp1046908

  Thank you

  Rizwan James

• VPN site-to-site dynamic.

  Hi all

  One of the customers was a question.

  They have an ASA 5510 and they will implement the vpn site-to-site dynamic, because some of their clients do not have a static IP address.

  They want to know, if, rather than create a vpn for all new sites, they may have a single configuration vpn for all new sites they add.

  Thank you!

  Maybe you will find information in these discussions that will help you understand what it takes

  https://supportforums.Cisco.com/discussion/11624431/site-site-VPN-if-rem...

  This link has a good example of configuration of ASA to make VPNS pair that uses dynamic IP

  http://www.Cisco.com/c/en/us/support/docs/security/ASA-5500-x-series-NEX...

  HTH

  Rick

• VPN site-to-site dynamic-to-static

  Dear

  I have a few sites already connected with ASA 5505 VPN site to site with both ending static IP address.  Normally, all traffic can be found without any problems.  Even, I used 'inside access management' for the two ASA.

  Now I have a new office with only the ADSL pppoe.  I used to install between Site B:remote the site dynamic IP and IP SiteA:static with a similar example of this easy VPN: http://www.cisco.com/en/US/products/ps6120/products_configuration_example09186a00805733df.shtml

  All my ASA 5505 run 1 8.4 (4)

  Site A - Static IP

  Site B - Dynamic IP with pppoe connection.

  After EasyVPN connected, I don't know how I remote manangment of the site a lan at the ASA 5505 B site?

  Best regards

  Alan.

  If you're ok with or the other solution, it is probably easier to use dynamic to static lan-to-lan, so, at least, that your solution is consistent and fair use lan-to-lan tunnel instead of customer vpn solution mixture and lan-to-lan.

• PIX-to-router VPN static-to-dynamic

  Dear friends,

  I'm trying to configure an IPSec tunnel between a router IOS and a PIX v7.0. I've seen some URL pointing here for a configuration example. However, this example only covers the v6.x PIX version, is not not helpful to resolve my case.

  My situation is that the router connects to a DSL provider and obtain a dynamic IP address and my PIX device has a static (Leased line) connection to the Internet. So, I have to establish the tunnel using preshared keys.

  How to make using v7.x on the PIX?

  Appreciate the help,

  Mauricio

  Mauricio,

  Here is an example for version 7.0 of PIX a tunnel L2L dynamic.

  http://www.Cisco.com/en/us/products/HW/vpndevc/ps2030/products_configuration_example09186a00804675ac.shtml

  You must create a dynamic encryption card, and use the tunnel defaultL2L-group for pre-shared key settings.

  The rate of this post, if that helps.

  See you soon

  Gilbert

• VPN tunnel with IP dynamic

  Question:

  Is it possible to install a GRE tunnel between two routers, one that has a dynamic IP, the other has a static IP address. If this isn't the case, GRE, is there another tunneling protocol we could use?

  In the search for setting up a VPN, I found that the way suggested to do is a GRE tunnel, so that dynamic routing work via VPN. We do not use dynamic routing, but I want the flexible design for future changes that will occur.

  Our facility is:

  2651XM (hub) to the corporate office (static IP). DS-1

  827H (spokes) to each branch (dynamic IP via DHCP). ADSL.

  IOS version 12.2 (13) T supports Multipoint GRE function which will allow your GRE tunnel on the side of ADSL to use a dynamic IP address. Locate the CCO love and documentation DMVPN (dynamic multipoint VPN).

• ASA IPSEC VPN with public IP dynamic

  Hey,.

  I have never deployed IPSEC VPN tunnel using ASA on two sides of a side using public IP dynamic production. I normally deploy VPN Tunnels with both sides using public static IP addresses (not always a public IP address on ASA directly however).

  So I wonder how stable it works with a static public IP and the other side uses dynamic public IP?

  Thank you

  Shuai

  If you use certificates and psk or main mode and aggressive it will work very well. I have a number of production sites using this method.

  Sent by Cisco Support technique iPad App

• VPN ASA ASA with dynamic IP of the branch

  Hello

  I would like to connect a private network Virtual Office HQ to a branch using two ASAs.

  I have a 5520 in the HQ and 5505 in the branch.

  My problem is in the office where I have a dynamic IP (ADSL).

  I couldn't find an example of this type of configuration.

  Can you help me?

  Kind regards

  Sergio Santos

  Hi Sergio,

  Well, you have two options:

  • Dynamic to static L2L tunnel:

  On the 5520, you must configure a dynamic encryption card because you don't know the IP address the 5505 will have and even if you IP address may vary. So:

  Crypto ipsec transform-set esp - esp-md5-hmac RIGHT

  Crypto-map dynamic dynmap 1 transform-set RIGHT
  Crypto-map dynamic dynmap 1 the value reverse-road
  map mymap 10-isakmp IPSec crypto dynamic mymap
  mymap outside crypto map interface

  If you already have other tunnels already configured them just change the name of the crypto map that I used above with one you already have, in the example I used a sequence of 10 number because I have more tunnels in place but you need without ensuring that the card encryption where you attach the dynamic crypto map has the highest value! ID recommend using a value of 65535, which is the highest, you can use, this will allow you to configure static tunnels in the future without having need to reconfigure one you linked to the dynamics.

  Besides that you must configure the tunnel-group... but as you know for tunnels L2L with PSK in MainMode tunnel-group name MUST be the IP address peer, and in this case, we do not know, do not worry, we can configure the PSK under the DefaultL2LGroup

  IPSec-attributes tunnel-group DefaultL2LGroup
  pre-shared-key *.

  That's all you need on the 5520, in addition to the basic configuration PH1 for the construction of a tunnel.

  On 5505 all you need to do is to set up a regular tunnel because from the point of view 5505, we know the IP address of the 5520 and it will not change:

  map MYMAP 1 IPSec-isakmp crypto
  defined peer X.X.X.X
  Set transform-set RIGHT
  match address MYCRYPTOACL

  Group of tunnel X.X.X.X IPSec-attributes
  pre-shared-key *.

  • The other option will be to configure EzVPN you use a 5505

  http://www.Cisco.com/en/us/products/HW/vpndevc/ps2030/products_configuration_example09186a00808a61f4.shtml

  http://www.Cisco.com/en/us/docs/security/ASA/asa72/configuration/guide/ezvpn505.html

  HTH!

• ASA to remote access VPN with external IP dynamic

  Hi forum,

  I was wondering if it was possible to set up an ASA to provide access to remote connections VPN (IPSEC or WebVPN/SSL) of the outside world, if the external IP address is dynamic (i.e. obtained through DHCP)?  I understand how to use DynamicDNS to provide a host name for the VPN clients, I ask simply if the SAA can be configured to allow VPN connections from a DHCP interface addressed.  I understand there are problems with the site to site VPN when both sides are addressed in a dynamic way, but it seems that the remote VPN access should work.  Just hoping to confirm this before I go and I'm working on a config.

  Thanks in advance...

  The same configuration applies.

  In my view, that the only difference is that with the external IP being dynamic:

  interface e0/0

  IP address dhcp setroute

  crypto map

  The only difference is that (the PCF file) VPN clients should have the VPN connection with a hostname (rather than an IP address) and the IP must be solved at the IPs of the SAA.

  I'll try to find you an example configuration if you do not.

  Federico.

• VPN between PIX with dynamic IP

  Can I make a VPN over the Internet with PIX or IOS VPN in each IP address dynamic and extreme (DHCP client) in the two extremes?

  Thank you

  If siempre sepas than las direcciones los extremos back there sets in el momento iniciar el tunel in peripheral los.

  Distinto are TR UN extremo tiene IP fija y el otro dinamica (vpn easy for example you can help ahi)

  --

  Alexis Fidalgo

  Systems engineer

  AT & T Argentina

• IPSEC VPN with Dynamics to dynamic IP

  Hello

  I tried IPSEC VPN with dynamic IP to dynamic (router to router) for some time. But still can not auto-établir the tunnel.

  Is someone can you please tell me if it is possible to do?

  If so, please share with me the secret to do work.

  Thank you!

  Best regards

  Rather than the Crypto map, I would use the profile of Crypto.  Then, establish you an IPSEC tunnel.  The beauty of the profile, is that you can run through it routing protocols, and you do not have to change constantly the cards whenever you change the topology of the network.  The "* * *" in the timer event is "minute hour day week month" so "* * *" is updated every minute.  In Tunnel destination, it's an IP address, not a hostname that is stored, but when you set it, you can put in a HOST name and it converts to the moment where you configure it to an IP address.

  So, if you type:

  config t

  interface tunnel100
  destination remote.dyndns.com tunnel

  output

  See the race int tunnel100

  It shows:

  interface Tunnel100
  tunnel destination 75.67.43.79

  That's why the event handler goes and becomes the destination of tunnel every minute what ever the DDNS says that is the new IP address.

  I have seen that two of your routers running DDNS.  They will have to do this.

  Local router:

  crypto ISAKMP policy 1
  BA aes 256
  preshared authentication
  Group 2
  ISAKMP crypto key XXXXXXX address 0.0.0.0 0.0.0.0 no.-xauth
  !
  !
  Crypto ipsec transform-set ESP-AES-SHA esp - aes 256 esp-sha-hmac
  !
  Profile of crypto ipsec CRYPTOPROFILE
  game of transformation-ESP-AES-SHA
  !
  interface Tunnel100
  Description of remote.dyndns.org
  IP 10.254.220.10 255.255.255.252
  IP virtual-reassembly
  IP tcp adjust-mss 1400
  source of Dialer0 tunnel
  tunnel destination 75.67.43.79
  ipv4 ipsec tunnel mode
  Tunnel CRYPTOPROFILE ipsec protection profile

  IP route 192.168.2.0 255.255.255.0 10.254.220.9

  Change-tunnel-dest applet event handler
  cron-event entry timer cron name "CHRON" * * *"
  command action 1.0 cli 'enable '.
  action 1.1 cli command "configures terminal.
  Action 1.2 command cli "interface tunnel100".
  Action 1.3 cli command "destination remote.dyndns.org tunnel".
  !

  --------

  Remote router:

  crypto ISAKMP policy 1
  BA aes 256
  preshared authentication
  Group 2
  ISAKMP crypto key XXXXXXX address 0.0.0.0 0.0.0.0 no.-xauth
  !
  !
  Crypto ipsec transform-set ESP-AES-SHA esp - aes 256 esp-sha-hmac
  !
  Profile of crypto ipsec CRYPTOPROFILE
  game of transformation-ESP-AES-SHA
  !
  interface Tunnel100
  Description of local.dyndns.org
  IP 10.254.220.9 255.255.255.252
  IP virtual-reassembly
  IP tcp adjust-mss 1400
  source of Dialer0 tunnel
  tunnel destination 93.219.58.191
  ipv4 ipsec tunnel mode
  Tunnel CRYPTOPROFILE ipsec protection profile

  IP route 192.168.1.0 255.255.255.0 10.254.220.10

  Change-tunnel-dest applet event handler
  cron-event entry timer cron name "CHRON" * * *"
  command action 1.0 cli 'enable '.
  action 1.1 cli command "configures terminal.
  Action 1.2 command cli "interface tunnel100".
  Action 1.3 cli command "destination local.dyndns.org tunnel".

  Thank you

  Bert

• ASA - ldap - user vpn static address

  Hello!

  I am trying to configure ASA to assign a static IP even to some user (User1) every time when it connect to the network via the AnyConnect client. We have Windows AD and that you are using the LDAP AAA server for authentication of remote access VPN users. I found in the document 'Cisco ASA 5500 Series Configuration using the CLI, 8.2 Guide' in the explanation section "Configuring external year for security device user permission to the server" and configured the ASA and user properties in AD exectly similarly:

  Firstly, I assigned a static ip address in the menu properties (section numbering) of User1 in Active Directory. Then I created the ldap attribute card where I traced msRADIUSFrameIPAddressattribute to IETF-RADIUS-Framed-IP-Address. attribute In the end, I applied this map to attribute ldap to LDAP AAA server group.

  Although I have implemented this, whenever I connect using User1 received powers AD I always get the ip address of the vpn pool rather a static ip address which I configured. In the output of debugging ldap 255 command I found the line "msRADIUSFramedIPAddress: value =-1062718956 ' but not any line that prove the above attribute map.

  It seems that the mapping does not work.

  All AnyConnect users get the policy settings defined internal group on ASA, including addresses form pool, dns etc server. I want User1 to get a static IP and inherit all other group policy settings.

  If someone has any ideas of how to fix this, please help.

  Thank you

  Hello

  Please give the output of the aaa server hs.

  I found the link that gives you the configuration of the requirement details.

  http://www.Cisco.com/en/us/docs/security/ASA/asa82/configuration/guide/ref_extserver.html#wp1661694

  I hope this helps.

  Kind regards

  Anisha

  P.S.: Please mark this message as answered if you feel that your query is resolved.  Note the useful messages.

• Public static JNLP vs dynamic one generated by PHP

  I have a problem with our application does not update when change us our JNLP file dynamically generated using PHP. "We use a versioned file using the ' < property name ="jnlp.versionEnabled "value ="true">" in our JNLP file.
  
  I tried using a static JNLP file and make the same change to the version and it updates on the client computer. I checked, using Wireshark, the response HTTP (headers) are the same between static and dynamic get requests. And that the return JNLP file is actually updated with the new version, it seems everything as Webstart are ignorant of the new version and starts just demand for caching when using the dynamic JNLP file.
  
  Note: I tested this with early access 7u2 because this version fixes the following bug: [Bug ID: 7063209 | http://bugs.sun.com/bugdatabase/view_bug.do?bug_id=7063209]
  
  Is there something in Webstart, which ignores the update because it is generated dynamically?
  
  Any help would be appreciated.
  
  Thank you
  Mike

  You say that the Last-Modified header is the same thing for your PHP version and static version?

• Is it possible to keep all static?   (vs dynamic SQL)?

  Hi all
  
  I have existing MS who after db Exchange should work with newly partitioned table partition name = date of entry both inside AND date_param, something like:
  
  sql_string: =' select * tt partition (P_'| date_param |') the problem of configuration required, I can't use any dynamic SQL and it really put me in the corner, do you think it is at all possible? I was thinking about a lot of things that may work, but date_param is just date < 12 - 7.-10. > and partition is preceded with PRT_?
  
  I can to with str_part: = ('(P_'|| date_param ||'') ') "), but it is already dynamic...
  
  Even after I create the temporary table and for sure, I know that the DDL inside the procedure should be ONLY dynamic?
  What is the dead end? There is a way to CREATE static? or simply to use kind of temp table created outside MS and clean it before use? or...
  
  I actually try to see why customer site cannot manage NDS or they just don't want it, but can't argue with that for now.
  I've got enough new to Oracle and couldn't do bad things on the SQL dynamic (NDS)?
  
  Thank you all
  TR

  Trento wrote:
  Hi all

  I have existing MS who after db Exchange should work with newly partitioned table partition name = date of entry both inside AND date_param, something like:

  sql_string: =' select * tt partition (P_'| date_param |') the problem of configuration required, I can't use any dynamic SQL and it really put me in the corner, do you think it is at all possible? I was thinking about a lot of things that may work, but date_param is just <12-Sep-10>and partition is preceded with PRT_?

  I can to with tmp_part: = ('(PRT_'|| date_param ||'') ') "), but it is already dynamic...

  Even after I create the temporary table and for sure, I know that the DDL inside the procedure should be ONLY dynamic?
  What is the dead end? There is a way to CREATE static?

  I actually try to see why customer site cannot manage NDS or they do not want, cannot buy with that for now. I'm pretty new to Oracle and could not do bad things on dynamic SQL?

  Thank you all
  TR

  Why the hell wouldn't you just query the table and apply the predicate? Oracle would then partition elimination for you.

  No need for anything either dynamics based on what you posted.

• ASA 5510 L2L VPN static gateway of azure and branches and

  Hello

  I am trying to configure an ASA to operate as a hub between two site-to-site VPN, at our office and the other on Azure.

  i.e.

  Office <-- internet="" --="">ASA <-- internet="" --="">Azure

  On the two sites I can establish a VPN for the hosts of the ASA and access on our data center network, but I can't seem to get the connectivity from end to end of Azure at our office or vice versa.

  Any ideas on what I can try as I have been hitting my head against a wall with this one.

  Hello

  If traffic also came from the blue to office network so it would seem that there is a problem with configuring VPN L2L between ASA and Azure, very probably on the Côte d'Azur.

  -Jouni