S 4340 missing disks after the installation of windows 7 ultimate

Similar Questions

• Error reading from disk after the installation of windows xp

  Ideas:

  • I got a new hard drive installed by professionals. I went to install Windows XP on my computer. He passed through the first stage, but after copying the files, it wouldn't restart. That repeatedly brings me to a screen that says: a disk read error occurred press Ctrl alt delete to restart and then it looks like it will restart but hten goees return the same screen. How can it be a disk error if it is passed by the installer and I've never touched the disc later? Now, I can't do anything with it. Any help would be greatly appreciated.

  Do not install an operating system is usually caused by (in order of probability):

  1. you are trying to install with other devices connected to the computer. Unplug them before trying to make an installation.

  2. "" "" defective installation media. "" Check the CD/DVD installation for scratches, tasks. Try another machine.

  3. bad optical drive. Test with another CD/DVD bootable or Exchange for a well-known work.

  4. faulty RAM. Test with Memtest86 + www.memtest.org . You will download the .iso image file to create a bootable cd. Burn the file with the third party burning software *-as an image, not in the form of data. Then start with the media that you did (you may need to change the boot priority in your BIOS so that the optical drive is the first boot device). The test runs immediately. The test run for an hour or two--at least that errors are seen immediately. If you get any errors, replace the RAM.

  A good free choice ImgBurn comes from www.imgburn.com .

  5. bad hard drive. Test with a diagnostic utility downloaded from site of the disc mftr... You create a bootable CD with the files you download. Burn the file with a third-party burning software - image, not in the form of data. Boot with the CD that you have done and do a full test of the reader. The physical tests fail, replace it.

  (Note: since you just replaced your hard drive is probably not the cause.) However, you should always test because it is not uncommon that new hard drives to the failure of the box.)

  6. other hardware components are faulty. MS - MVP - Elephant Boy computers - don't panic!

• Missing drivers after the upgrade to Windows 7 Ultimate

  I upgraded my HP Pavilion dv4 5113 Windows Home Premium from Windows Ultimate edition. I can't the following drivers for my machine upgraded. His works well but the yellow marks when you open computer, management and Management is boring please help.

  Controller Serial Bus (USB)

  PCI\VEN_8086 & DEV_1E31 & SUBSYS_1836103C & REV_04

  PCI\VEN_8086 & DEV_1E31 & SUBSYS_1836103C

  PCI\VEN_8086 & DEV_1E31 & CC_0C0330

  PCI\VEN_8086 & DEV_1E31 & CC_0C03

  Ethernet controller

  PCI\VEN_10EC & DEV_8168 & SUBSYS_1836103C & REV_06

  PCI\VEN_10EC & DEV_8168 & SUBSYS_1836103C

  PCI\VEN_10EC & DEV_8168 & CC_020000

  PCI\VEN_10EC & DEV_8168 & CC_0200

  PCI device

  PCI\VEN_10EC & DEV_5229 & SUBSYS_1836103C & REV_01

  PCI\VEN_10EC & DEV_5229 & SUBSYS_1836103C

  PCI\VEN_10EC & DEV_5229 & CC_FF0000

  PCI\VEN_10EC & DEV_5229 & CC_FF00

  PCI Simple Communications controller

  PCI\VEN_8086 & DEV_1E3A & SUBSYS_1836103C & REV_04

  PCI\VEN_8086 & DEV_1E3A & SUBSYS_1836103C

  PCI\VEN_8086 & DEV_1E3A & CC_078000

  PCI\VEN_8086 & DEV_1E3A & CC_0780

  SM Bus controller

  PCI\VEN_8086 & DEV_1E22 & SUBSYS_1836103C & REV_04

  PCI\VEN_8086 & DEV_1E22 & SUBSYS_1836103C

  PCI\VEN_8086 & DEV_1E22 & CC_0C0500

  PCI\VEN_8086 & DEV_1E22 & CC_0C05

  Unknown device

  ACPI\HPQ0004 * HPQ0004

  Thank you in advance.

  Hello

  Download and install the following:

  Intel Chipset driver.

  After this Setup is complete, restart the laptop.

  Then, download:

  Intel USB 3.0 driver.

  Realtek LAN Driver.

  Realtek card reader driver.

  Intel MEI driver.

  HP ProtectSmart.

  Kind regards

  DP - K

• ITunes does not start after the installation of Windows 10

  ITunes does not start after the installation of Windows 10, 1511 version (OS Build 10586.164). ITunes version 12.3.2.35, 6 GB RAM, Intel i3 @3.3 GHz. Itunes and Ipodserver module will run by Manager jobs, but Itunes does not open. iTunes starts in SafeMode as explained in the link below (hold SHIFT and control on your keyboard while you open iTunes).

  Fix unexpectedly closes or problems of launch in iTunes for Windows - Apple Support

  Solution, according to this link, is:

  If the problem does not occur in Mode safe, remove any third party plug-ins iTunes: solving problems with third party plug-ins - Support Apple iTunes but the link has been archived, and I can't find any plug-ins installed iTunes. Any other ideas?

  For general advice, see troubleshooting problems with iTunes for Windows updates.

  The steps described in the second case are a guide to remove everything related to iTunes and then rebuild what is often a good starting point, unless the symptoms indicate a more specific approach.

  Review the other boxes and other support documents list to the bottom of the page, in case one of them applies.

  More information area has direct links with the current and recent buildings if you have problems to download, must revert to an older version or want to try the version of iTunes for Windows (64-bit-for old video cards) as a workaround for problems with installation or operation, or compatibility with QuickTime software or a third party.

  Backups of your library and device should be affected by these measures but there are links to backup and recovery advice there.

  TT2

• Pavillion g6: my laptop audio stop working after the installation of window 10

  After the installation of window 10 my speakers to codec audio idt high definition stop working completely.please help me out of the this.thanks

  Try to update the drivers via windows update or hp support assistant. Headphones work?

• Satellite L555 - 10K - FN keys do not work after the installation of Windows 10

  I installed 10 64-bit Windows (original was Windows 7 64-Bit)

  My FN keys do not work after the installation of Windows 10.

  There is no possibility of a screen-Switch, and the brightness setting and activate Touchpad...
  Do you know any help

  Hello

  I think that your model of laptop is not possible to Win10.
  Check it please https://forum.toshiba.eu/showthread...mation-website

• I have a compaq presario cq60 with vista which was able to start after the installation of windows updates. HP recovery failed with error code 100a and bios self-test gave error fail #1-07. What can I do?

  I have a compaq presario cq60 with vista. Could not start after the installation of windows updates. HP recovery failed with error code 100a and bios self-test gave error fail #1-07. I took the hard drive and installed in my office. Windows Explorer displays the main and recovery partitions.

  The primary partition has the following folders (including hidden & system)

  The recovery partition has the following (including the language files more)

  Someone at - it ideas why my laptop does not work?

  Thank you

  Greg

  Hello

  You press F11 on startup with a HP Compaq to start the recovery process.

  For problems with the recovery process, you will need to contact HP.

  BIOS problems:

  There are messages for the HP Forums for posters with similar errors:

  http://h30499.www3.HP.com/T5/notebook-HP-ProBook-EliteBook/notebook-HDD-problems-TEst-status-1-07-fail/TD-p/658902

  http://h30499.www3.HP.com/T5/notebook-PCs-pavilions-Presario/HP-Pavilion-dv8000-getting-1-07-fail-error/TD-p/883284

  http://h30499.www3.HP.com/T5/notebook-PCs-pavilions-Presario/HP-Pavilion-notebook-dv6000-1-07-fail/TD-p/1069457

  All the answers it point to a drive about to fail

  See you soon.

• After the installation of Windows 'important' 3 updates my screensaver started does not. I get a message that says "ScreenSaver:Photo screensaver.scr - unable to locate component".

  Original title: screen saver does not start because MSVCR100.dll was not found

  After the installation of Windows 'important' 3 updates my screensaver started does not. I get a message that says:

  ScreenSaver: Photo screensaver.scr - unable to locate component.

  This application has failed to start because MSVCR100.dll was not found. Reinstalling the application may fix this problem.

  The screen saver starts after you close the error message. I've never had a problem with my screen saver up to that after I downloaded updates. I don't know how to reinstall the application. I tried Windows Fix - It Solutions, but it does not work. He repeated to me that it was a mistake.

  Help, please. Thank you.

  Hello

  It didn't reinstall the ATL update, it reinstalled 2005 Redistributable. So now, I have 2005 and 2010 x 86 both. And it says that two dates installiation are two days after I installed the 2010. I know 2005 and the update was uninstalled, because I checked after restart the computer and before you install the 2010 version. Very curious.

  But my Screensaver works and access to the camera seemed to work after uninstalling / reinstalling the software. So, good. Thank you.

• After the installation of Windows 7 repair I 219 updates. Best way to install? Small batches... oldest first? Others?

  After the installation of Windows 7 repair I 219 updates. Best way to install? Small batches... oldest first? Others?

  In the previous 18 months there have been many updates toxic that caused problems... these fixes are well eliminated or fixed retroactively or this process will be as walk minefield?

  I currently intend to install some office and .net updates separately and to wait on the optional updates updates security priority are installed.

  Thanks for any idea.

  Properly installed all updates of security except IE11 upgrade [has a full update of IE8 that should cover most security problems... [Since I use Firefox... or whatever it is, but it is to say... no biggie].

  I installed the updates [ie8, etc] 1 security and updates in batches of 20-30 for most recent first then older then. Then I installed the office updates and then a point net 3.51.research showed several versions of dot net needed.

  After each batch, I did a restore pt.

  Note: this repair facility corrected a connection problem that prevented programs and 32-bit browsers... including malwarebytes to connect to the net. I had followed the many expert suggestions to fix this problem without success before the repair facility.

• The screen of my Sony Vaio laptop VPCS11FM completely lost its brightness after the installation of Windows 8. What should do?

  I installed upgrading W7 W8. Already during the final phase of installation, the screen of my Sony Vaio laptop VPCS11FM completely lost its brightness after the installation of Windows 8. I tried the settings of brightness through the hardware buttons and in energy savings, but it remained the same. What should do? Karl

  Looking for a display updated sony driver.   Its always a good idea to do so during the updating of the OSs.

• Windows 8 OEM samsung original is disabled after the installation of windows updates.

  I have the original windows 8(Samsung Laptop) confirmed by Samsung as the original windows. Have this laptop for about 2 years now and have reset my windows again. But this time after the installation of windows updates, my windows are disabled and the watermark comes and it is said to activate windows. Samsung said support windows is authentic and check with Microsoft. But Microsoft has no support for 24 hours and support is not live at this time. Can someone help me with this problem. Please, I beg you. And I tried to put the key in the firmware to activate, but nothing helped. And the OEM key is invalid for activation at all.and add I activated my windows by phone before the update using the technique of slui 4... and after it started to update. And now reactivate cant using this key method.and calling OEM is not valid anywhere.

  Hello

   
   
  Please contact Microsoft Community.
   
  We regret sincerely all the inconvenience caused to you.
   
  I suggest you try the phone activation this time and see if it helps.
   
  a. at the start screen, drag from the right side, or hover your mouse on the top right of the screen to display the menu of charms.
  b. tap or click the charm of parameters.
  c. press or click on change PC settings.
  d. If your PC is not activated, computer settings provide instructions that are customized to your activation error. If telephone support can provide assistance for your mistake, tap or click the appropriate link, which may resemble one of the following conditions:
  > Activate

  > Activate by phone

  I suggest you refer to the following article for more information.

  http://Windows.Microsoft.com/en-us/Windows-8/activation-errors
   

  Hope the helps of information. Let us know if you need help with Windows related issues. We will be happy to help you.

  Kind regards
  Anusha

• After the installation of Windows 8, I lost my photos

  After the installation of Windows 8, I lost my pictures and can not find them

  I found my photos in the old Windows folder.

• Old dualboot options still available after the installation of Windows 8 Pro on a desktop Pc which had XP and Windows 8 prewiev version on that front.

  Old dualboot options still available after the installation of Windows 8 Pro on desktop in XP, but now triple options. Windows 8 Pro (volume 1), Windows 8, old windows installation.  Anyone who knows how to get rid of the last two options?  The good thing is now that I don't have to put a password everytime I turn on the computer.

  Press the Windows key + X and then click System

  

  Click on advanced system settings

  Click the Advanced tab

  Under Startup and recovery, click settings

  

  Select Windows 8 and uncheck the box "time to display list of operating systems.

• Hello, we are runing Adobe Acrobat Professional 7.0 and it suddenly stopped working for one of our computer after one month after the installation of windows 10. Someone had the same problem and it is resolved?

  Hello, we are runing Adobe Acrobat Professional 7.0 and it suddenly stopped working for one of our computer after one month after the installation of windows 10. Someone had the same problem and it is resolved?

  Not compatible with the system after XP. Upgrade.

• My CC of LR 2015 stops right, "do not answer", after the installation of windows 10. What should I do?

  My CC of LR 2015 stops right, "do not answer", after the installation of windows 10. What should I do?

  This means that a problem with the graphics card.

  You update your graphics card drivers?