S70 - A satellite fails to connect to the WLan

Similar Questions

• Satellite A100-158 connects to the WLAN but not to internet

  I have a Satellite A100-158. It is used to disconnect frequently the network wireless in my house, but now even if the connection still appears on the program of Intel PROset/wireless and is shown as connected, I can not access the internet more. I don't know what the problem might be that the wireless signal is excellent.

  For the moment, I plugged the Ethernet cable to the router to access the internet. Does anyone have any suggestions as to what could be the problem?

  Hello

  I can't provide the exactly the solution to this problem of WiFi, but I think you should check the whole parameters on the WLan router.
  First, you must remove all security settings such as encryption key and MAC address filtering.

  Then check the settings of the laptop. If you use a Wlan configuration tool as Utility Intel ProSet windows has the configuration option must be disabled!
  In addition, access the Wlan properties and check the TCP/IP protocol settings.
  The IP address, subnet mask, and the default rejuvenation should be set to automatic

  Good luck and look at a few

• HP Photosmart 7520 fails to connect to the WLAN after deactivation/activation

  Nice day

  I use HP Photosmart 7520 with wireless connection.

  I can print for the first time when the printer connects to the WIFI, but when I turn the printer off and turn it back on, the printer is no longer on the WLAN.

  The screen and print network report says that everything is OK - signal strength is good, he is connected, IP address correct, gateway IP ok, everything is correct and very well - but the printer IS NOT on the WLAN. I have used several analytical tools and I did 'ping' and the prnter is not there.

  There is a big BUG! How can I solve this problem?

  Thank you

  PS: If I want the printer to work again, I have to manually reconnect again to the WLAN

  Since the other topic of forum is very polluted, I paste here the relevant solution

  Left and right of the screen are a House (upper-left), back (lower-left) and a cancellation (bottom right, it's a red X) buttons.  You may need to use a flashlight to see them because probably they are not lit.

  • -Keys in the original sequence (top left), back (lower left), cancel (bottom right), back (lower-left).  This should bring up the menu engineering.
  • In this menu select Menu Underware.  You will see a display similar to the arrows for a TV remote control (up, left, right, down, arrows with an OK button in the middle).
  • Use the arrow key to the right and go into the system menu (the menu names are displayed in the upper left corner).  Press OK
  • Use the arrow key to the left and go to the system mode timeout.  Press OK
  • Use the down arrow key to set the timeout to 0.  Press OK.
  • Exit by pushing cancel (bright red x in the lower right corner) until you have returned to the home screen.

  You can avoid the printer to go into mode 'sleep' and then lose connection. As a consequence will increase energy consumption.

• Utility of fingerprinting Toshiba - "Failed to connect to the sensor.

  Having a problem with the Toshiba fingerprint utility. The program works fine until I try to use any sort of firewall/antivirus program, even the built-in Windows Firewall: S the scanner still works fine for the boot time scanning, as well as for windows logonm but as soon as any kind of firewall/antivurus software loads up, it fails to connect on the sensor. I added the program to the lists allow but still nothing... So far I tried with AVG Internet Security, Outpost Security Suite and by default, the Windows Firewall. Windows Firewall turned on for awhile, I got when I bought the laptop and there was no problem.

  It's a Qosmio X 500 - 00 X, it uses the same installation of windows when I bought...

  See you soon!

  Hello

  Please update the software of fingerprint. You can find it here:
  http://EU.computers.Toshiba-Europe.com-online decision-making supported Downloads & => Download drivers

  Also try a different firewall and AntiVirus. I have good experiences with AntiVir and Kaspersky Security Suite.

• Satellite Pro A40 can't connect to the WLan using the Win XP

  Hi all

  Newbie on your site so thank you in advance for your answers ;-)

  Picked up a Toshiba Satellite Pro A40, completely formatted and installed a legal XP Pro.

  Trying to connect to the internet using a Netgear wg511 card works on my other laptop, it will not connect even though I installed the driver for it?

  It comes up with 'limited or no connectivity problem occurred because the network has not assigned a network address of the computer.

  Any ideas please?

  Thanks Mike

  Hello

  First of all, you must update the WLan driver.
  I put t know what wireless network card has been installed, but you can find WLan card details in Device Manager-> network adapters.

  In addition, I recommend to disable all the security settings on the router and then try to connect to the wireless network.
  If you will be able to connect to the Wlan, you can enable security settings (Wlan encryption, mac address filtering, firewall, etc.) again.

  Last but not least, you can try to use this command in a DOS (CMD)
  Ipconfig / renew

  Big names

• Fails to connect to the Proxy Server

  My internet works but are used.  He says he "fails to connect to the Proxy Server" is due to firewall settings?  and how to change them.

  Your message is in the forum for people needing help with the anti-malware program from Microsoft Security Essentials (MSE).

  Suggest you contact support OBJECTIVE to: http://help.aol.com/help/product/aim/

• Acer Iconia A-810 fails to connect to the Google Server

  I just this tablet and everything so far is ok, but it fails to connect to the Google server. He has no problem connecting to other servers however. Both laptops and another my Tablet connect to the Google server perfectly. I use ATT broadband. So I guess that something in the Acer Iconia tablet is the origin of the problem. Any suggestion?

  Thanks in advance,

  Marina

  1. go to setting-> Applications-> shop game Google-> erase-> empty the Cache.
  2. go in setting-> Applications-> Service Google Play-> erase-> empty the Cache.
  3. Enter your Google username and password after opening Google Play Store again.

  I hope this works.

• Vista problem: "failed to connect to the windows service, Windows cannot connect to the system event.

  I have reported this problem on my PC at home that connects to the internet. My laptop runs Vista Home Premium and I can't connect to the internet. I took my laptop on a trip, tried to connect to the wireless network that was free to the place we are. Could not connect, and after this initial test, the following is displayed after the start of "failed to connect to the Windows Service, Windows cannot connect to the system event notification service. This problem prevents limited users to logon to the system. As administratvie user, you can view the system event log to see why the service did not respond. "(have no idea how or what it means) when I go to the task bar you want to connect to a network, it is said:" the dependency service or group could not start"and if I go ahead and press"connect to a network"it says it can't find.  I search for computers on the network (who I'm sitting next to) and then try to diagnose the problem and it cannot. I have limited knowledge of this type of problem. Anyone have this problem and how to fix it?

  Hi ptkein,

  Thanks for posting your question on the Forums of Windows Vista.

  Option 1: You can download and install the latest network card drivers and see if that can solve the problem.

  Option 2: Follow the link below to fix network connection problems

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-network-connection-problems

  Option 3: Follow the link below to solve Internet connection problems

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-Internet-connection-problems

  Option 4: To verify if a third party application is a cause, follow this link (http://windows.microsoft.com/en-us/windows-vista/Advanced-startup-options-including-safe-mode) for this boot to the desktop using the safe mode with networking option and try to install the network. If the problem is resolved, you will need to perform a clean boot by following the steps in the following article to refine the exact source and isolate it: http://support.microsoft.com/kb/929135

  Let me know if it worked.

  Hope it will be useful.

  Thank you and best regards,

  Kadoch - Microsoft Support

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Windows Media Center extender on my XBOX works initially, but not after reboot of my XBOX. Error: Failed to connect to the Xbox 360 could not connect to the windows Media Center computer.

  It's VERY odd and very annoying!

  I set up my laptop next to my Xbox 360 with an Ethernet cable directly connecting the laptop to the XBOX, and the laptop is on our wireless network. The XBOX has access to the internet (shared through the laptop), and when I test the PC connection and the connection XBOX Live sound fine to all.

  So I'll try to set up Windows Media Center, it works great! I "Add Extender", put the code to 8 digits. It passes through the installation, all works, no problems and WMC opens on the XBOX, I can go into my library, watch movies etc... works great!

  However! As soon as I turn my XBOX off and back on, it will fail to connect to the WMC.

  He says his 'find Windows Media Center PC' which seems to work fine, it goes to the ' Windows Media Center loading screen "contact...". ", and after about 10 seconds, I get an error"failed to connect the Xbox 360 could not connect to windows Media Center PC. Make sure that the PC is turned on and connected to the network.

  I tried to configure the Extender repeatedly, whenever it works fine until I restart the XBOX... :/ - and its strange cause I still the internet connection (shared through the laptop) after turning on the XBOX, its really JUST Media Center which is screwing around.

  She continues to keep trying to connect then repeatedly fails.

  If I wanted to, I could re-configuration the WMC Extender EVERY TIME turn off the Xbox, which works the first time without fault, but that's all just stupid.

  I can't really understand what is happening here... any help would be appreciated.

  Hello

  Refer the article that could help you solve this problem.
  http://support.Microsoft.com/kb/932163

• Failed to connect to the JMX service (209,1046) when you try to view the logs in PeopleTools 8.55

  I am trying to use the new functionality of Log Viewer PeopleTools 8.55.

  It is a great improvement that allows developers/testers/support team members to display the application server logs, process scheduler logs and newspapers PIA; with a regular account of the PeopleSoft Application.

  You have no need to create a system account on the server (Linux or Windows) for users to view the logs.

  I managed to configure the Web server log viewer, but when I try to Application I can see message failed to connect to the JMX service (209,1046).

  
  

  When I configure the JMX for APPDOM user, I tried PTADMIN with no success.

  
  

  Could someone describe the process to change the JMX user for Tuxedo domain?

  
  

  Thank you

  Stéphane.

  the default installation of DPK password is password.

  Kind regards

  / Stéphane.

• Failed to connect to the user when it connects to SQL Server 2008 R2 gateway

  Hi - This is my first post!

  I have problems to connect to a SQL Server 2008 R2 to Oracle database 11 g R2 database, use the product of the gateway.

  Previously, he has worked, but we moved the database SQL 2005 to 2008 (R2).

  We receive this error while trying to query through the link (Select * FROM DUAL@ADSRD)

  ORA-01017: name of user and password invalid. connection refused

  [Oracle] [ODBC SQL Server driver] [SQL Server] Failed to connect to the user 'SQLUSER '. {NativeErr 28000, = 18456} [Oracle] [ODBC SQL Server driver] Invalid connection string attribute {01 S 00}

  ORA-02063: preceding 2 lines of ADSRD

  01017 00000 - "invalid username/password; connection refused '.

  * Cause:

  * Action:

  Error on line: 1 column: 35

  The DG4MSQL configuration is here:

  HS_FDS_CONNECT_INFO = //SSU_PRD_APP/IntegrationStagingDb [BSYS-sql2]

  HS_FDS_TRACE_LEVEL = OFF

  HD_TRANSACTION_MODEL = READ_ONLY

  #HS_FDS_DELAYED_OPEN = FALSE

  HS_FDS_FETCH_ROWS = 100

  HS_OPEN_CURSORS = 50

  
  

  The database is hosted in its own instance on the sql2-BSYS Server

  Then... on the SQL Server event logs returns this:

  Failed to connect to the user 'SQLUSER '. Reason: Failed to try to connect using SQL authentication. Server is configured for Windows authentication only. [CLIENT: 192.168.10.179]

  However, the SQL Instance IS configured to enable mixed mode authentication.

  I can't work on what I missed, and I can confirm if I'm actually to a compatibility issue between the gateway and the version of SQL server, that we are now trying to connect.

  Help please!

  Is the user name in your SQL Server database in the capital, mixed mode letters or small letters?

  Currently, you have created a database link that tries to authenticate on the server SQL using SQLUSER in capital letters. If you use mixed or small letters, so be sure to write the user name (and password) as it is in the create database link statement and surround it with double quotes.

  If you have created the link of database correctly, try an ODBC connection for example from your client and add the user name and password. Does it work?

  -Klaus

• An unknown error has occurred during playback of the video file. failed to connect to the server of dynamic links

  I recently bought a drone DJI Phantom 3 kind have been treatment of videos more than usual and not have not had any problems. I use Lightroom for cataloging movies and I use the first to change.

  Since yesterday, I was not able to import any movie that I get the following error

  an unknown error has occurred during playback of the video file. failed to connect to the server of dynamic links

  

  Initially, I thought that it was due to a spectacular crash of drone (Physics isn't SHE!) who corrupted the file that was being logged, m ais I can now no longer import any movie to Lightroom.

  
  I tried the following

  1. a different memory with a new registration card

  2 removing and re - import an old movie

  3. to remove and re-import and old movie created by another camera

  4. to remove Lightroom and rolling back to the previous version of LR CC (CC 2015 [1014445])-had the advantage of getting rid of the annoying new import dialog screen. -

  5. upgrade to El Capitan to see if maybe OSX update may help.

  
  

  None of them had no effect, can anyone help?
  

  
  

  
  

  
  

  
  

  
  

  Hello

  You're welcome ShawWellPete, I thank you for everything.

  Yes, this person is the windows user, but it was the same question that could have been resolved by quicktime 7. (pending confirmation)

  Try to disable the start-up services and restart the mac and then try: take control of start-up and connection elements. Macworld

  There could be some service startup that is in conflict.

  Concerning

  Jitendra

• Failed to connect with the user name "Administrator".

  Hello

  I want to configure vCD in VCO, but I am faced with error. I'm by train through the configuration of the vCO.

  I get the error message https://10.99.133.212:443 , Failed to connect with the user name "Administrator". And the description of the error is: "the API version information could not be obtained for the host https://10.99.133.212:443 () (administrator@System)!'."

  Here are the entries I provide:

  Host: 10.99.133.212

  Organization: System

  Authentication: basic

  Session: shared

  and name of user and password.

  What could be the error here? My vCO has IP 10.99.129.33. And I imported the vCD also SSL certificate.

  Kind regards

  Bethy

  You must first remove the new plug-in...

  VMware KB: Uninstall a plug-in for VMware vCenter Orchestrator

  Remember that you use step 6.3 in this article to delete the contents of the package as well. To verify that the workflow and actions have been removed, check that the following workflow category (and all children of it) no longer exist:

  / Library/vCloud Director

  And all related Action modules should have disappeared as well:

  com.vmware.library.vCloud. *.

  Once you have completed all steps of the KB, install version 5.1 of the plugin, configure and restart the vCenter Orchestrator Server service, once again to complete the installation.

• Satellite M70: I can't connect to the WLan access point

  I have several wireless laptops, all work fine - except my M70.
  I use Intel Proset, and he sees the access point, but says "unable to connect" when I try.
  The signal is high (2 meters distance).

  I tried with WEP, WPA and without security. I am absolutely convinced that I entered the right keys.
  The access point is a Belkin Pre - N-, but I tried with a point of access 3Com, with the same problem - my Ipaq, my other PC, and all guests can connect,- but not my Toshiba!
  The wireless card is the standard Intel, with the latest driver from October 2006 intalled.

  Getting desperate...

  Hello

  If you get a signal strong, so I guess that the laptop is already connected to the access point. Or am I wrong?
  On my laptop, the computer WLan small icon appears only if I connected to the Wlan and then I can see the State of the signal.

  However, you suggested to use the Intel Proset utility to configure the WiFi network but on the clean Windows configuration. Have you tested it?

  This question seems very strange to me.
  Sometimes it of not possible to connect the WiFi network because of poor compatibility between the router and wireless network card.
  My router supports Wlan AB mode and my second card for computer laptop support BG.
  That's why I m not able to connect to the Wlan. Maybe it s also your case.

  On my router, I can also put the MAC address filtering. You should check this option on your router.
  But generally it is not easy to say why it happens. You know you should check every single option and if it s not possible so I guess that it s a compatibility issue.

• My ZTE open C unable to connect to the wlan with 63-signs-hex key.

  Hello

  my C open from ZTE unable to connect to the wlan with WPA2-PSK and a 63 sign hex key. When I create a 2. ESSID with WPA2-PSK a sentence normal, everything's fine.

  Oliver

  Hi OliverwithZTE,

  I understand that you have connection problems to your network WPA2-PSK.

  Unfortunately, WPA2-PSK is currently not supported on Firefox OS version 1.3. Only WPA-TKIP and WPA2-AES are supported.

  -Ralph