Satellite L350d - 12 M - BIOS update failed - computer won't start

Similar Questions

• Satellite L670 - 1 FT Bios update failed

  I have a laptop "Satellite L670 - 1 FT" computer when the update of the BIOS does not.
  There is a possibility of screen WITHOUT doing a BIOS update, and if yes what do I need?

  I tried to copy the BIOS file. ROM on a USB key and start the laptop by pressing Fn + B.
  It takes about 5-10 sec for the stick, but unfortunately I still have no display.

  Thanks in advance

  + The message has changed: the content has been translated.

  If the BIOS is not successful, the ROM module must be flashed with special crisis disk BIOS
  Unfortunately, as far as I know something like this can be done by a Toshiba authorized service provider available in your country.

• Satellite L350D - 12 M - BSOD and now it won't start up

  Hi all

  I use my Satellite L350D almost everyday with no problems (it is around the age of 18 months). I left it over the weekend and when I got home I started it upwards and once everything was loaded I got the dreaded blue screen of death. I restarted my computer, but it is simply a noise whirring while the screen is off. I tried to leave message to see if the screen lights up, but apparently not.

  When I started it again after leaving it from one day to the next I got to a screen where it says I pourrais either press F2 or F12 (I think), but the keyboard was not record the fact that I was pushing the keys.

  Any thoughts?

  Hello

  Just a simple question: have you tried an external monitor on the laptop? Maybe the display internal doesn t work properly.
  Check this box!

  However, in your case, I will try to remove the battery and the AC adapter. Wait an hour and then reconnect the two devices. Now, you should try to restart the laptop.

  In the worst case, it s a hardware problem and you need professional help :(authorized service provider

• Vista Service Pack 1 update fails - computer will not start and cannot be repaired

  The computer which is an Acer desktop computer, running Windows Vista Premium.  In the last 6 months updated Vista tried Service Pack 1 update to install Vista about 8 times and failed every time a reason any.  Just before this latest incident, a facility was "cancelled" in the Middle for some reason any.  I restarted the computer and almost immediately was advised that there is an update, which turned out be SP-1.

  I started the update, and some time later I received a message that the update was successful, and that he had to be restarted the computer.  I clicked on the button restart and the Installation continues during the shutdown.

  When the computer tried to restart initialization failed and I ended up after several lines of information that looked as if it might be checking drivers and then information began to look as if she might be reading the register lines.  Each line has 2 numbers separated by a slash (/), who scored on a single line at the top of the screen, (white letters on black background) after a certain time the count to stop with the line of text of flickering on the same entry.

  It is the line that goes to the screen when the information keeps changing.

  !! 0xc01a001d!  37636/92292 (\Registry\Machine\components\winners\x86...)

  Since the failure of the Windows Vista SP1 update, when the system begins to start, after a short while, he starts playing what seems like lines in the registry, and after a few moments he always stops with the same accurate information just flicker.  At this point, it seems that this scenario will continue forever.  The hard drive is accessible, as if trying to read something, over and above.  The hard drive light flashes, instead of being on regularly, but only for a while.  After that, even the flickering stops.

  I have tried to start mode without failure, then after loading some files and after some time (5 or 10 seconds) the displayed files always end with the same file at the bottom of the list and what seems to be a status extend the message please know...  Shortly after the screen is empty, the fails to start and the computer is restarted.

  Usually what will happen is that the computer will begin to start up again, but because the previous boot failed, it asks if you want to go to startup repair, which, at first, seems to work fine, but after a little time it brings up a dialog box asking if you want to restore to the previous good Restore Point.  The display will then return to the same routine he had previously, and she runs to always if not interrupted.

  If you click the Cancel button, a message appears indicating that you cannot interrupt the current process, so the only way that you can try something else is to Shut Off the Power in now the switch down, permanently.

  [Note: the notes above have not all accurate messages, Word for Word, exceot for the Hex error line.]

  Hello
   
  Thanks for posting on Microsoft Answers.
   
  Try to put the folder windows update catalog distribution and software
  Try the following steps:
  1. Insert the Windows Vista installation disk into the disk drive and restart the computer.
  2. When you are prompted to restart from the disc, press any key.
  3. When you are prompted, configure the language to install, time and currency format and keyboard or options for method of entry that you want, and then click Next.
  4. on the page to install Windows, click on repair your computer.
  5. on the System Recovery Options, click the version of the Windows Vista operating system that you want to repair, and then click Next
  6. in the System Recovery Options page, click command prompt.
  7. type cd C:\windows\winsxs, and then press ENTER.
  8 type ren pending.xml pending.old, and then press ENTER.
  9. in the registry editor, find and delete the following registry subkey:
  HLKM\Offline Components\AdvancedInstallersNeedResolving
  HKLM\Offline Components\PendingXmlIdentifier
  HKLM\Offline Components\NextQueueEntryIndex
  10. at the command prompt, type exit to quit the registry editor. Press ENTER.
  11. click on restart
   
  More information:
  The update is not installed successfully, you receive a message, and the computer restarts when you try to install an update in Windows Vista: http://support.microsoft.com/kb/949358
   
  Hope this helps
   
  Kind regards

  Niranjan
  Microsoft Answers Support Engineer

  
  Visit our Microsoft answers feedback Forum and let us know what you think.

• BIOS update failed on Satellite P200 - 13 M

  Hello world

  I have a Satellite P200, (PSPB6E-03G01XFR).
  Yesterday, after attempting to update my BIOS version with the windows application, my phone was cut.

  I downloaded the new version of the bios of Toshiba-Europe Web site (v2.30) and I tried to use the Crisis_Recovery_Disk but no result. :(
  Can someone help me please?

  Unfortunately, in your case only the ASP can help you.

  Does your BIOS update fails and only the ASP can update the ROM module damaged by using a special version of the BIOS

  So, don t waste time and ask the ASP in your country to help.

  Best regards dude

• Satellite L755-S5349 - BIOS update failed - black screen

  Hello.

  So yesterday, I got a Toshiba pop-up message to update my BIOS, so I clicked it and it started to update but then it says "error checking".

  So I closed it, cause I had to restart my computer after one previous update with another program and I thought to try to update the BIOS after you restart.

  But once it restarted it is off, so I tried to put back market but the screen is black, lights are immediately (food, batt etc.) and the fan works just as well. I tried to take the battery out and in again but screen remains black.

  Could someone please tell me what you think it might be and what I have to do.

  I also tried with a HDMI, but it does not recognize.

  Thank you for your help

  Hello

  I think I have bad news for you.
  To me, it seems that the update of the BIOS didn't
  Why? Who knows maybe that some applications that runs in the background affected the BIOS update process.

  I've updated the BIOS on my laptop last night, everything went well. First, I downloaded the BIOS package from the Toshiba page. Then I unzipped the folder.
  I closed all applications that looked like Firewall, antivirus etc software
  Then I did the BIOS update

  At least in cases where the BIOS update failed, you must get in touch with a local ASP Toshiba in order to solve this problem in the best of cases they need to update the module ROM again

  Good luck

• Satellite L40 PSL48E - BIOS update fails on VISTA 32 bit SP1

  The 2.0 with latest downloads BIOS update failed.

  After adjustment of the rights of the user and Disabling UAC is remaining the following command line error:

  C:\TEMP\BIOS>winflash.exe P20B200. BIN
  Cannot copy the BIOS image. (File name error?)
  C:\TEMP\BIOS >

  No idea how solved it, file name is correct?

  You unzip the package to update the BIOS first?
  It is very important that the BIOS package will be unpacked first.

  Then, you can update the BIOS the winflash.exe execution.

• Vostro 3500 BIOS update failed - need recovery procedure

  I got a Vostro 3500 laptop computer work and was doing maintenance to update. I downloaded and installed the BIOS update recommended for this laptop... Dell Vostro 3500 system BIOS 3500 has 12. EXE | Release date of BIOS of Windows/DOS (3 MB) 21/07/2014 updated 21/07/2014 recommended BIOS update failed and left no work of BIOS of the computer. F2 is dead. It will not start. I am sure that there a backup BIOS or primitive still, as when I start the machine without battery and power, using the end key he's constantly trying to read the data from a 2 GB flash drive. I guess he wants to reload the BIOS from a file. I know how to get the ROM content from the file above using the /writeromfile parameter. The big question is, what type of file the 3500 wants to read, and what is the name of the file it is seeking? Is the flash player must be bootable? What is a FRIEND or a Phoenix BIOS? Can someone please? Thanks, Terry

  Here's how to recover a flash update BIOS of your laptop Vostro 3500 failure...

  1. download the Dell BIOS update .exe file to a USB flash drive.

  2. run the .exe with the /writehdrfile parameter file

  3. run the .exe with the /writeromfile parameter file

  4. copy the .hdr winery50.hdr

  5. remove the battery and the power of the dead computer

  6 Insert the flash drive into the USB port on the computer of the death

  7 press and hold the end key and then connect the AC power

  8 dead computer reads USB flash and request if the update should be performed

  9. let the update at the end and then restart.

  10. computer now works normally.

  Useful web site: http://mickitblog.blogspot.com/2011/09/dell-bios-switches.html

• BIOS update failed - where can I download BIOS for floppy drive?

  Hello

  After the BIOS update fail by Windows I need to reflash.

  Where can I download the bios for floppy drive files '?

  Thanx

  Hello

  Update of the traditional BIOS cannot be downloaded.
  Only focused on winning BIOS is available on the European driver Toshiba page.

  In your case, you will need to contact a local ASP.
  The technician can help you and able to reflash the BIOS using a disc of crisis of the BIOS.

  Good luck

• BIOS update failed - Dell Precision M4600

  I just got a used M4600 and the currently installed bios is A08. When I try to update to A16, it restarts, said it is updating the firmware, but fails at 0%. It gives no reason and no code error I can say. Thanks in advance for any help you guys can provide.

  Is NOT the issue! There is nothing wrong with motherboards M4600 se.

  Everyone tried to find why when you attempt an upgrade of the BIOS, the system fails immediately with a "BIOS Update Failed" basis and any specific error code or more explanations. The answer is in the PDF below--that is the message displayed when the BIOS authentication will fail!

  Just look for the Firmware Signature Dell's "feature" that was introduced in a number of laptop including the M4600.  Doc PDF to download. It is a feature introduced by the NIST requirements.

  In a Word, they changed the way BIOS authenticates a BIOS file before he will use it to update the firmware BIOS & CBS. The M4600 is in the list of "Legacy Systems", where it was introduced. Basically, these systems do NOT have the Firmware of Signature When produced.

  Version A04 introduced this feature. After you have that installed, you will have an option to activate the requirement of Signature of the Firmware (default is). Once activated, it cannot be disabled!

  The problem starts in worm BIOS A08. Something in the code is wrong. Because on some M4600s, it updates the BIOS AND activates the requirement of Signature of the Firmware. After that, the system will authenticate ALL the other versions of the BIOS, so you will NOT be able to upgrade past version 8!

  I got many, many systems for a company. I'm currently sitting on 33 (Yes, that many) M4600 with this exact same situation!

  An exchange of motherboard does not correct the problem. It is to give you a new BIOS chip to tinker with.

• After that windows update computer won't start

  After that the most recent windows updated my computer did not start...  I did update the windows twice and each time I had to restore my computer to an earlier time. I don't know why after upgrading my computer does not... Can someone help me with this please?

  These are updates that I was installing that caused my computer to make it not start:

  A security update cumulative for Internet Explorer 8 for Windows Vista (KB2360131)

  Download size: 9.2 MB

  You may have to restart your computer for this update is taken into account.

  Update type: Important

  Update of security for Microsoft Office Excel 2007 (KB2345035)

  Download size: 8.5 MB

  You may have to restart your computer for this update is taken into account.

  Update type: Important

  Update of security for Microsoft Office System 2007 (KB2344875)

  Download size: 7. 4 MB

  You may have to restart your computer for this update is taken into account.

  Update type: Important

  Update of security for Microsoft Office System 2007 (KB2345043)

  Download size: 2.0 MB

  You may have to restart your computer for this update is taken into account.

  Update type: Important

  Update security for Windows Vista (KB2207566)

  Download size: 189 KB

  You may have to restart your computer for this update is taken into account.

  Update type: Important

  Update security for Windows Vista (KB2378111)

  Download size: 12.0 MB

  You may have to restart your computer for this update is taken into account.

  Update type: Important

  Update security for Windows Vista (KB2387149)

  Download size: 557 KB

  You may have to restart your computer for this update is taken into account.

  Update type: Important

  Update security for Windows Vista (KB979687)

  Download size: 881 KB

  You may have to restart your computer for this update is taken into account.

  Update type: Important

  Update security for Windows Vista (KB981957)

  Download size: 1.0 MB

  You may have to restart your computer for this update is taken into account.

  Update type: Important

  Update security for Windows Vista (KB982132)

  Download size: 118 KB

  You may have to restart your computer for this update is taken into account.

  Update type: Important

  Update for Windows Vista (KB2345886)

  I found KB981957 to be the culprit on that I worked on a system of XP SP3.  With this update installed, I get an error C000021A Service Control Manager BSOD.  I have manually uninstalled this update by using the Recovery Console and then used Windows Update through IE and deselected this update.  All the other updates installed correctly and the system starts properly.  I would like to know why this update is causing this problem.  Anyone with the same problem?

  It reminds me of a similar situation earlier this year with BSOD KB991765.  The cause of the BSOD is a virus that has infected system driver files.  Once clean, the installation worked very well.  I've done many scans on this system and have not yet found any viruses.

• I have an Acer 1810tz-4008 and computer won't start battery. New charged battery - what should I do?

  Original title: the battery starting

  I have an Acer 1810tz-4008 and computer won't start battery.  New charged battery - what should I do?

  Hello

  Check with support from Acer.

  Acer - USA - Service and Support - drivers
  http://us.Acer.com/AC/en/us/content/support

  Acer - worldwide
  http://www.Acer.com/worldwide/selection.html

  ===================================

  Other information that might help:

  References to Vista also apply to Windows 7.

  Check with support from the manufacturer of their books online and the drivers and their forums system
  (as applicable) for known issues. Some manufacturer issued BIOS and other updates to help the battery
  problems.

  Follow these steps to remove corruption and missing/damaged file system repair or replacement.

  Run DiskCleanup - start - all programs - Accessories - System Tools - Disk Cleanup

  Start - type in the search box - find command top - RIGHT CLICK – RUN AS ADMIN

  sfc/scannow

  How to fix the system files of Windows 7 with the System File Checker
  http://www.SevenForums.com/tutorials/1538-SFC-SCANNOW-Command-System-File-Checker.html

  Then run checkdisk (chkdsk).

  How to run check disk in Windows 7
  http://www.SevenForums.com/tutorials/433-disk-check.html

  =================================================================

  Other information that might help:

  Control Panel control - plan change Options - power plans - power - advanced settings
  Parameters for the drainage and the use of parameters (this is how much to use and not how much or how)
  long to load).

  In fact, what causes a lot of wear on a battery empties it too low on several occasions. With today
  systems overload are not a problem.

  Here are some tips to help and troubleshoot battery issues.

  Old battery? Unplug the power to the computer - remove the battery and clean the contacts with a pencil
  eraser (do not use this, if your battery is fine slots - just clean up the edges of the knife which fit in)
  them and be careful). Batteries are old, or it could be a problem with the computer.
  Check with the support of the machine system, and many of them have on line forums.

  New Lithium-Ion type battery usually last longer if you do not unload their less than 30%
  However on a laptop that not extend their life a lot. Best is to use the a/c adapter
  When this is possible.

  I use the free version of BatteryBar to monitor my battery. Click on the green button on the
  Yellow box on the right side of the page to download the latest stable version.

  BatteryBar - free version available
  http://osirisdevelopment.com/BatteryBar/index.html

  Another good program

  Vista battery saver - free
  http://www.codeplex.com/vistabattery

  Problems with the lives of its use and the battery of power - Mr Fixit
  http://support.Microsoft.com/GP/windows_battery_power_settings

  You can also check with the manufacturer of system and forums that many use their own
  proprietary software to monitor the battery and they could be known problems with your battery.

  ============================================================

  Battery meter: frequently asked questions
  http://Windows.Microsoft.com/en-us/Windows7/battery-meter-frequently-asked-questions

  Battery saver
  http://Windows.Microsoft.com/en-us/Windows7/conserving-battery-power

  Solutions to common battery problems
  http://Windows.Microsoft.com/en-us/Windows7/solutions-to-common-battery-problems

  What is the precise the battery meter?
  http://Windows.Microsoft.com/en-us/Windows7/how-accurate-is-the-battery-meter

  ============================================================

  Try this - to make a Restore Point

  How to create a System Restore Point in Windows 7
  http://www.SevenForums.com/tutorials/697-system-restore-point-create.html

  How to do a system restore in Windows 7
  http://www.SevenForums.com/tutorials/700-system-restore.html

  Then Control Panel - Manager of devices - Batteries - Double click on each item - drivers - tab
  Update the drivers (which can do nothing) - then do a right click and UNINSTALL each - RESTART
  who will update the driver stacks.

  Problems with the lives of its use and the battery of power - Mr Fixit
  http://support.Microsoft.com/GP/windows_battery_power_settings

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="" -="" mark="" twain="" said="" it="">

• If my printer USB cable is connected, my computer won't start?

  If the printer is on and the USB port connected.  The computer won't start.  If I turn on the laptop with the USB plugged in and as it starts and then turn on the printer, everything works fine.  Almost ok.  I think I should be able to leave the printer on all the time as I do at work.  Then when I start the computer, the printer is ready.  Every other printer I've ever had worked this way.  Any suggestions?

  Maybe the printer looks like a hard drive (some printers have card readers that make them look like a disk) and the computer attempts to boot from the USB drive instead of the hard drive?  It would be a modification of the settings in the BIOS

  'Teething problems of a PC with a connected external USB drive.
    <>http://wdc.custhelp.com/app/answers/detail/A_ID/1201/~/problems-booting-a-PC-with-an-external-USB-drive-connected>

  Another article I found...  Not sure I can add much further than.

  "USB device does not initialize at startup or Windows XP no longer meets the start or stop"
    <>http://support.Microsoft.com/kb/830957 >

  HTH,
  JW

• I had installed CS6 and perform an update now CS6 won't start. How can I rectify this?

  I had installed CS6 and perform an update now CS6 won't start. How can I rectify this?

  The message reads as follows:

  The procedure entry point

  ? ClearCustomSkin@SkinSetClient@ui@dvaui@@UAEXImmutableStrin

  g@utility@dvacore@@@Z could not be located in the dynamic link

  Dvaui.dll library.

  Chris van Zyl

  Logtra Solutions

  Mobile: + 27 (0) 83 498 2123

  Office: + 27 (0) 12 348 9793

  Fax: + 27 (0) 12 348 9784

• Satellite Pro U400 BIOS update failed - what is the BIOS Boot-block access

  Hello

  My last update of the BIOS has failed and my laptop PSU45E PrU400 Satellite is now out of use.
  I want to use the recovery disk of crisis with a USB floppy drive, but I don't know the key combination to run the boot block.
  Is that someone can help me?

  Best regards

  Hello

  I was wondering what crisis recovery disk you have?  :|
  In my experience the special drive is required, which is available only for ASP technician
  That's why it of necessary to contact the ASP in your country to reflash BIOS.

  In my opinion you shouldn't t try recovery disks of the crisis who loves you in the net, it can drive to the mobo damage