SE host HA status

Similar Questions

• ESX 3.5 - host connection status error

  I am running 3 ESX 3.5 servers in a cluster, run by VC 2.5.

  I followed my environment with IPmonitor. I was randomly to the alerts below on one of my hosts.

  Current value:

  State of the connection - home (State = no response)

  Alarm: State of home connection

  ()

  Description:

  State of the host connection on esx01.company.com from green to red to alarm

  When I check Virtual Center, the host shows "not responding" and therefore make the virtual machines. This happens only briefly and the virtual machine never loses connectivity to the network. They don't even migrate to another host. The service console has 2 NICs (1 active, 1 standby). I don't know why this is happening. I don't get any other errors on the network.

  Any help would be greatly appreciated.

  Thank you

  Scott

  This day you run for ESX 3.5?  This happens every now and then on my systems as well and I think that vCenter Update 5 is supposed to solve a problem similar to this one, but that includes a firewall between your ESX and vCenter.

  -KjB

  VMware vExpert

  Don't forget to leave some points for messages useful/correct.

  Post edited by: kjb007

• Temperature for the host hardware status

  Hello to all,

  mia domanda, come da oggetto, e' come fare a parameter dei valori sui alarm set definition by it check della temperatura.

  Dove devo kindly do I valori di Re?

  Non riesco a quali siano soglie by cui notification parta oppure understand not.

  Grazie a tutti

  The healt del sistema e Marin automatically in base alle impostazioni del relativo CIM.

  Quando qualcosa e fuori scala viene triggerato.

• Network host adapter and the status of the connection

  Does anyone know the property of the object to get the host 'Link Status' network adapter?

  I can get the name of the NETWORK adapter and the speed duplex but nothig on the status of the connection

  Thank you

  You can not get the status of link directly (as far as I know).

  You can detect the status of "link down" through the linkSpeed in PhysicalNic object property.

  You can use something like this

  (Get-VmHost  | Get-View).Config.Network.Pnic | %{
       if($_.LinkSpeed -eq $null){
            Write-Host $_.Device "Link down"
       }
  }
  

  ____________

  Blog: LucD notes

  Twitter: lucd22

• Alarm battery State host

  Hello

  I installed ESXi4 on some servers, and they all upward with an alarm in vCenter:

  Status: WARNING

  Name: Host battery status

  These are all Dell PowerEdge 2950 servers. Does anyone know what means this alarm? This could be a bug and deactivate this alarm?

  We have the same. This isn't a bug. Sometimes, this alarm is triggered but he always comes back to green after a while (a few hours).

  From time to time the material wants to check battery you en BBWC raid then you get the waring.

  You also get the warning that the battery is simply charging.

• Mavericks of hp photosmart b110

  I'm sure you can help. I try to get my Photosmart B110a connected wireless to my Macbook Pro in Mavericks 10.9.2

  The printer is connected is the network that I can connect via my browser using IP inside address and I see everything about the printer and I have a choice of menu, it gives me the ink level, confirms the connection, Hello is allowed including host name, status appears as loan. This lead me to the conclusion that the computer is in talks with the printer, the Mavericks just doesn't seem to know that.

  When I select system preferences, click the plus sign + nothing comes up under the default section.

  If I use IP option and I get the IP address of the printer and I have to manually enter the IP address it comes back and tells me that it is HP Photosmart B110 series; Then when I click on Add it comes back and tells me "failed to verify the printer on your network. Unable to connect to? ??. ?. ? reason and error ".

  If I add the printer it shows it is available but I can't print on it. Nevertheless, I can open the printer and I have not even enter the HP printer utilities, it gives me the correct device information, I CAAN print test page, check the levels all that makes the utility. I print quality diagnostic page as I type (and it seems good).

  Then, when I try to print a document, nothing happens and I get the error unable to connect to the printer.

  I am really at my wits end with this.

  Concerning

  Hello

  Try to add the printer using its IP address, however, change the Type of HP Jetdirect and check if that might cause a difference and to allow the addition of the printer for printing.

  In addition, don't forget to specify your router brand and model to better understand its Multicast capabilities, which can affect the performance of Hello.

  Shlomi

• Utility to Format SD won't install correctly

  I installed the SD V.2.1.0.0A format utility on my Portege M200, but when I try to launch it I get the error message "unexpected error." Error code = 0x0034FF02"the utility opens, but the SD reader is not accessible. I uninstalled and reinstalled, but in vain. What should do?

  Hello

  I'm not 100% sure, but before you can use this tool, you must install SD Card Driver Set V2.0.4 initially. Is this driver already preinstalled and what is the Secure Digital host controller status in Device Manager?

• Turn on the wifi hotspot does not

  T440s

  Windows 7 64-bit.

  ==================

  Pilots to see the wlan C:\Windows\System32>netsh

  Name of the interface: wireless network connection

  Driver: Intel (r) Dual Band Wireless-AC 7260
  Vendor: Intel Corporation
  Vendor: Intel
  Date: 17/11/2014
  Version: 17.13.2.2
  INF file: C:\windows\INF\oem29.inf
  Files: total 3
  C:\windows\system32\DRIVERS\Netwsw02.sys
  C:\windows\system32\DRIVERS\Netwfw02.dat
  C:\windows\system32\drivers\vwifibus.sys
  Type: Wi - Fi Native Driver
  Radio types supported: 802. 11 b 802. 11 g, 802.11n, 802. 11A
  FIPS 140-2 mode supported: Yes
  Hosted network supported: Yes

  ==================

  C:\Windows\System32>netsh wlan start hostednetwork
  The hosted network could not be started.
  The group or resource is not in the correct state to perform the requested operation.

  ==================

  C:\Windows\System32>netsh wlan show hostednetwork

  Hosted network settings
  -----------------------
  Mode: refused
  Name SSID: "Airtel231".
  Maximum number of guests: 10
  Authentication: WPA2-Personal
  Encryption: CCMP

  Hosted network status
  ---------------------
  Status: Not available

  =====================

  Hello

  Follow this post:
  https://forums.Lenovo.com/T5/ThinkPad-X-series-laptops/X1-carbon-Lenovo-settings-app-hotspot-update/...

• configuration of the copy Max locks RT

  There are about 33% chance of my RT lock when I try to export an .ini file using Max Configuration.vi of copy on my host.  Status of the RT in pharlap watch display always a charge permanent CPU 80% and 20% on his two sons, once he's locked up.  If it doesn't lock upwards, the export takes 3-5 seconds to complete.

  I use LabVIEW 8.6 and 8.8.0f2 DAQMX.  There are about 60 tasks on the RT. The RT is an Intel Core 2 Duo on an ASUS P5K motherboard.

  Here's how I call the speed VI:

  

  Any suggestions on the prevention of the RT of lock-up are welcome.

  Thank you.

  
  

• HA failure of the event

  I am configuring HA events between an application ODP.NET (Managed, 4.121.1.0) and our CARS (11.1.0.7.0) to facilitate the resumption of fast connection. We did a test vacuum by (1) connection to the node to be reduced, so the connection is in the pool. (2) brining this node down. (3) connect again. It did not work. I ran a trace ODP.NET (level 7) and noted the following:

  2014-11-05 09:59:33.737782 TID: 7 (PRI) (HA) VERSION = 1.0 service = instance db = database db2 = db host node2 status = downhill = reason = user

  2014-11-05 09:59:33.751285 TID: 7 (PRI) (SVC) (ERR) OracleHANotificationManager.HandleEvent (OracleHANotificationManager::HandleEvent()) has failed. -String was not recognized as a valid DateTime.

  Instead of ODP.NET pruning the connection pool served as planned, he reused it, the cause:

  2014-11-05 10:00:06.425818 TID: 1 (PRI) (ERR) OracleCommand.ExecuteReader () (txnid = n/a) OracleInternal.Network.NetworkException (0x80004005): error Oracle ORA-12571 met---> System.Net.Sockets.SocketException (0x80004005): an established connection was abandoned by the software in your host computer

  at System.Net.Sockets.Socket.Send (Byte [] buffer, Int32 offset, Int32, SocketFlags socketFlags size)

  to OracleInternal.Network.TcpTransportAdapter.Send (OB OraBuf)

  to OracleInternal.Network.TcpTransportAdapter.Send (OB OraBuf)

  to OracleInternal.Network.WriterStream.Write (OB OraBuf)

  at OracleInternal.TTC.OraBufWriter.FlushData)

  at OracleInternal.TTC.TTCExecuteSql.WriteOall8Message (Byte [] sqlStmtByteStream, Int32 cursorId, dbChangeRegistrationId an Int64, Int64 executeOptions, ColumnDescribeInfo colDefinesInfoArray, Int32 longFetchSize, Int32 arrayBindCount, numDefineCols of Int32 [], Int64 noOfRowsToFetch, SqlStatementType stmtType, MarshalBindParameterValueHelper & marshalBindParamsHelper, Boolean bWriteFirstRow)

  at OracleInternal.TTC.TTCExecuteSql.SendExecuteRequest (OracleConnectionImpl commImpl, Byte [] sqlStmtByteStream, Boolean bHasReturningClause, Int32 cursorId, dbChangeRegistrationId, ColumnDescribeInfo [] columnDefines, noOfRowsToFetch Int64 Int64, Boolean parse, Boolean execute, fetch Boolean, describe Boolean, Boolean bAutoCommit, bDisableCompressedFetch Boolean, SqlStatementType stmtType, Int32 longFetchSize, arrayBindCount of Int32, Int64 [] scnForSnapshot, MarshalBindParameterValueHelper & marshalBindParamsHelper, Boolean bWriteFirstRow)

  at OracleInternal.ServiceObjects.OracleCommandImpl.ExecuteReader (String queryString, paramColl OracleParameterCollection, CommandType commandType, OracleConnectionImpl connectionImpl, OracleDataReaderImpl & rdrImpl, Int32 longFetchSize, Int32 lobPrefetchSize, OracleDependencyImpl orclDependencyImpl, scnForExecution of Int64 [], Int64 [], scnFromExecution, OracleParameterCollection, bindByPositionParamColl, Boolean & bBindParamPresent, Boolean isDescribeOnly, Boolean isFromEF)

  at Oracle.ManagedDataAccess.Client.OracleCommand.ExecuteReader (Boolean requery, fillRequest Boolean, CommandBehavior behavior)

  Connection string is defined with "events HA = true; Load balancing = true; »

  This is Bug 10334624, which has been fixed in Oracle DB 11.2.0.4 and 12 c. No changes are necessary to the side ODP.NET to solve the problem, but the DB must be upgraded.

  If cannot be upgraded DB server, you can ask a single patch for DB 11.1.0.7 via My Oracle Support.

• How to disable journaling documented in vmkernel.log in ESXi 5.5 u2

  Hello community!

  I'm trying to disable debug logging vmkernel.log but so far nothing helps. My vmkernel.log is watered by something like this:

  [Debug ACPI]  (Integer 2015 - 06-30T 07: 17:08.051Z cpu0:32866) 0 x

  00000000

  00001e00

  [Debug ACPI]  Chain 2015-06-30 T 07: 17:08.051Z cpu0:32866) [0 x 16] "" H2: 0xD7 command == 0 ".

  [Debug ACPI]  Chain 2015-06-30 T 07: 17:08.051Z cpu0:32866) [0x0f] ' H2: 0xD7 PETE:

  [Debug ACPI]  (Integer 2015 - 06-30T 07: 17:08.051Z cpu0:32866) 0 x

  00000000

  00000080

  [Debug ACPI]  Chain 2015-06-30 T 07: 17:08.051Z cpu0:32866) [0x1c] ' H2: 0xD8 notification processor.

  [Debug ACPI]  (Chain 2015 - 06-30T 07: 17:08.052Z cpu0:32866) [0 x 24] ' H2: 0xD3: bits4 CSR_HA set to 0.

  [Debug ACPI]  Chain 2015-06-30 T 07: 17:08.052Z cpu0:32866) [0 x 19] ' H2: CSR_HA 0xD4 Bit3-> 0.

  [Debug ACPI]  Chain 2015-06-30 T 07: 17:08.055Z cpu0:32866) [0 x 28] ' H2: 0xD0 enter Manager SCI for HECI-2.

  [Debug ACPI]  Chain 2015-06-30 T 07: 17:08.055Z cpu0:32866) [0x2d] ' H2: 0xD1 host interrupt status set to 1.

  [Debug ACPI]  (Chain 2015 - 06-30T 07: 17:08.055Z cpu0:32866) [0 x 24] ' H2: 0xD3: bits4 CSR_HA set to 0.

  [Debug ACPI]  Chain 2015-06-30 T 07: 17:08.055Z cpu0:32866) [0 x 19] ' H2: CSR_HA 0xD4 Bit3-> 0.

  [Debug ACPI]  Chain 2015-06-30 T 07: 17:08.350Z cpu0:32866) [0 x 28] ' H2: 0xD0 enter Manager SCI for HECI-2.

  [Debug ACPI]  Chain 2015-06-30 T 07: 17:08.350Z cpu0:32866) [0x2d] ' H2: 0xD1 host interrupt status set to 1.

  [Debug ACPI]  (Chain 2015 - 06-30T 07: 17:08.350Z cpu0:32866) [0 x 24] ' H2: 0xD3: bits4 CSR_HA set to 0.

  [Debug ACPI]  Chain 2015-06-30 T 07: 17:08.350Z cpu0:32866) [0 x 19] ' H2: CSR_HA 0xD4 Bit3-> 0.

  [Debug ACPI]  (Chain 2015 - 06-30T 07: 17:08.350Z cpu0:32866) [0 x 17] ' H2: 0xD6 ME WP! = ME PR'

  [Debug ACPI]  Chain 2015-06-30 T 07: 17:08.350Z cpu0:32866) [0 x 19] ' H2: 0xD6 Message header:

  [Debug ACPI]  (Integer 2015 - 06-30T 07: 17:08.351Z cpu0:32866) 0 x

  0000000080040011

  [Debug ACPI]  Chain 2015-06-30 T 07: 17:08.351Z cpu0:32866) [0 x 26] "H2: 0xD6 TState:PState:SeqNo:Command:

  [Debug ACPI]  (Integer 2015 - 06-30T 07: 17:08.351Z cpu0:32866) 0 x

  00000000

  00001f00

  [Debug ACPI]  Chain 2015-06-30 T 07: 17:08.351Z cpu0:32866) [0 x 16] "" H2: 0xD7 command == 0 ".

  [Debug ACPI]  Chain 2015-06-30 T 07: 17:08.351Z cpu0:32866) [0x0f] ' H2: 0xD7 PETE:

  [Debug ACPI]  (Integer 2015 - 06-30T 07: 17:08.351Z cpu0:32866) 0 x

  00000000

  00000080

  [Debug ACPI]  Chain 2015-06-30 T 07: 17:08.351Z cpu0:32866) [0x1c] ' H2: 0xD8 notification processor.

  [Debug ACPI]  (Chain 2015 - 06-30T 07: 17:08.352Z cpu0:32866) [0 x 24] ' H2: 0xD3: bits4 CSR_HA set to 0.

  [Debug ACPI]  Chain 2015-06-30 T 07: 17:08.352Z cpu0:32866) [0 x 19] ' H2: CSR_HA 0xD4 Bit3-> 0.

  [Debug ACPI]  Chain 2015-06-30 T 07: 17:08.353Z cpu0:32866) [0 x 28] ' H2: 0xD0 enter Manager SCI for HECI-2.

  [Debug ACPI]  Chain 2015-06-30 T 07: 17:08.353Z cpu0:32866) [0x2d] ' H2: 0xD1 host interrupt status set to 1.

  [Debug ACPI]  (Chain 2015 - 06-30T 07: 17:08.353Z cpu0:32866) [0 x 24] ' H2: 0xD3: bits4 CSR_HA set to 0.

  [Debug ACPI]  Chain 2015-06-30 T 07: 17:08.353Z cpu0:32866) [0 x 19] ' H2: CSR_HA 0xD4 Bit3-> 0.

  What I did:

  1. updated the file config.xml in/etc/vmware/hoistd. Currently, section < Journal > looks like this:

  < Log >

  < Directory >/var/log/vmware/< / book >

  Info < level > < / level >

  < maxFileNum > 8 < / maxFileNum >

  < > 524288 maxFileSize < / maxFileSize >

  pass < name > < / name >

  < outputToConsole > false < / outputToConsole >

  < outputToFiles > false < / outputToFiles >

  < outputToSyslog > true < / outputToSyslog >

  < syslog >

  local4 < Setup > < / installation >

  < ident > go < / ident >

  < logHeaderFile > /var/run/vmware/hostdLogHeader.txt < / logHeaderFile >

  < / syslog >

  < / log >

  For the record, I changed < level > (was verbose)

  2. changes to the advanced settings:

  Verbose for info Config.HostAgent.log.level

  Vpx.Vpxa.config.log.level verbose for info.

  No results even after reboot of the host.

  I missed something?

  This ESXi is Lenovo custom image.

  Hello

  I met exactly same problem with our brand new Lenovo x 3650 M5 machines. Unfortunately, VMware was not able to say where these newspapers come as there is not a hardware problem.

  If you feel comfortable, you can decrease vmkernel loging level by:

  core of the system settings set - setting = acpiDbgLevel - value = 1 esxcli

  Then, you will need to reboot your host.

  I hope it helps.

• Using 'or' in a loop

  Get stumped on this one and looking for any help.  This snippet of a script basically comes right after adding hosts again in a cluster.  It checks to make sure that guests are connected before proceeding.  It has been working fine until we hit a cluster with a host in maintenance mode .  Come in white on how to add maybe one or a statement that would allow me to include as a State maintenance mode.  Any contribution is appreciated.

  #Importing host information collected earlier csv

  $CSVhosts = import-Csv.\VMHost.csv

  #Checking that the hosts are connected before proceeding

  {foreach ($vmhost to $CSVhosts)

  {}

  [string] $status = (get-vmhost-name $vmhost.name | select ConnectionState)

  Write-Host "connection status of" $vmhost.name "="$status"'-process will run when the status of the host is connected" "

  Start-Sleep - seconds 1

  }

  While ($status - don't ' @{ConnectionState = connected} ")

  }

  With the help of one or one in all in State would work, but you also use a table of the status of the target and use the operator of notcontains.

  Something like this for example

  $waitForThese = 'Connected', 'Maintenance '.

  #Imporing host information collected earlier csv

  $CSVhosts = import-Csv.\VMHost.csv

  #Checking that the hosts are connected before proceeding

  {foreach ($vmhost to $CSVhosts)

  {}

  $status = get-VMHost-name $vmhost.name | Select the ConnectionState - ExpandProperty

  Write-Output "connection status of the $($vmhost.name) = $status - process will run when the status of the host is connected.

  Start-Sleep - seconds 1

  }

  While ($waitForThese - notcontains $status)

  }

• ESXi alerts-Vmotion

  Gurus,

  Can a Vmotion arrive smooth if there is no alert warning in the node ESXi.

  I see a battery of a host alert. It will have an impact to evacuate the guests of vmotion as I plan a maintenance window bit where I have to use vmotion to evacuate guests from the node.

  Draw the attention of

  Host battery status

  Rahul-

  It's actually one of the goals of vMotion evacuate a host you need to put in Maintenance mode. There should be no problem with that.

  André

• A script for the e-mail notifications to all detectors of vCenter device 54 default works as expected, however it ends with an error.

  Hello

  We test the automatic configuration of alerts by email of all the alarms of 54 by default since version 5.0 of the device of vCenter.

  Since this is something that we intend to do on all the installations/upgrades, it can be a time-consuming task having to manually set each alarm set on each vCenter so I indicated to an article in the blog of VMpros which appears to address a similar task and who suggests using PowerCLI script to take care of this:

  http://blog.vmpros.nl/2011/07/04/VMware-change-alarm-actions-with-PowerCLI/

  I fixed the script from its original version because it shouldn't change certain actions of alarm to send alarm notifications at a different e-mail once a week. Instead, we will propose a one-time activity.

  After configuring vCenter server connection information and change the e-mail addresses, I have successfully tested the custom script to add notifications by e-mail to a test alarm (named "Test alarm") to a simple action, that I had created earlier (turn on/off a virtual computer in our laboratory). The added script notifications by e-mail to our alarm test as expected without error.

  Before you change the script to add e-mail notifications to all 54 defect detectors as needed, I decided to test the custom script against one of the predefined alarms (named 'Host the status of material power'). While the script added notifications by e-mail to the alarm 'Material receiving power status' as expected, he finished with errors.

  I just want to make sure that our custom script contains no script errors before using it on all the installations/upgrades (any suggestion or criticism is welcome).

  I pasted the error resulting from the prompt of Windows PowerShell commands below.

  Thank you and best regards,

  Massimiliano

  ==================================================

  PowerCLI D:\ >.\Change_Alarm_Datacenter.ps1

  Action Type Trigger

  -----------     -------

  SendEmail...

  SendEmail...

  SendEmail...

  New-AlarmActionTrigger: 21/05/2012-16:35:11 new-AlarmActionTrigger A

  specified parameter was incorrect.

  D:\Change_Alarm_Datacenter.ps1:37 car: 82

  + Get-AlarmDefinition-name '$actAlarm1 ' | Get-AlarmAction | New-AlarmActionTri

  walking landing < < < < - StartStatus 'green' - EndStatus "yellow."

  + CategoryInfo: NotSpecified: (:)) [-AlarmActionTrigger] new, Inva)

  lidArgument

  + FullyQualifiedErrorId: Client20_AlarmServiceImpl_NewAlarmActionTrigger_

  ViError, VMware.VimAutomation.ViCore.Cmdlets.Commands.Alarm.NewAlarmActionT

  rigger

  UID: /VIServer=administrator@vcenter5:443/Alarm=Alarm-alarm-17/SendEma

  ilAction = 1508771755/AlarmTriggeringActionTransitionSpec =-83030421

  6.

  StartStatus: Green

  EndStatus: yellow

  Repeat: false

  AlarmAction: SendEmail

  UID: /VIServer=administrator@vcenter5:443/Alarm=Alarm-alarm-17/SendEma

  ilAction =-1903891658/AlarmTriggeringActionTransitionSpec =-8303042

  16.

  StartStatus: Green

  EndStatus: yellow

  Repeat: false

  AlarmAction: SendEmail

  UID: /VIServer=administrator@vcenter5:443/Alarm=Alarm-alarm-17/SendEma

  ilAction =-1765994019/AlarmTriggeringActionTransitionSpec =-8303042

  16.

  StartStatus: Green

  EndStatus: yellow

  Repeat: false

  AlarmAction: SendEmail

  ==================================================

  Okay, I think I found the problem.

  You set 3 actions on this alarm (3 x Email).

  This means that it

  Get-AlarmDefinition -Name "$actAlarm1" | Get-AlarmAction
  

  Returns 3 objects (one for each action).

  Unfortunately, the New-AlarmActionTrigger cmdlet wants 1 as input Action, not a table object.

  The solution is to select the Action of explictely for which you want to change the trigger.

  Something like that

  Get-AlarmDefinition -Name "$actAlarm1" | Get-AlarmAction | Select -Index 0 | New-AlarmActionTrigger -StartStatus "Green" -EndStatus "Yellow" Get-AlarmDefinition -Name "$actAlarm1" | Get-AlarmAction | Select -Index 1 | New-AlarmActionTrigger -StartStatus "Red" -EndStatus "Yellow" Get-AlarmDefinition -Name "$actAlarm1" | Get-AlarmAction | Select -Index 2 | New-AlarmActionTrigger -StartStatus "Yellow" -EndStatus "Green"
  

  Beware, the script does not remove the old triggers, so you will end up having several triggers for actions.

  First use the remove-AlarmActionTrigger to remove any existing triggers.

• Managed Exchange of comments (static vs 'Windows') file

  Anyone know of any article talks about the advantages and disadvantages of creating a static in a pagefile guest OS (or if it's at all different that he put on a bare metal OS)? I have 4 Server 2008 R2 and Windows 7 Ultimate 1 on a host of memory of 8GB, running off a WD Raptor single 300 GB hard drive. I am committed specifically on memory (granted 9FR) to test balloning. Although the performance was surprisingly good, I wondered recently if a static file (good'ole 1.5 x RAM) should improve performance at all. So far, he seems to have improved performance a little, especially when I'm features intensive disk through multiple clients. Of course, this could just be a little illusory, the placebo effect, that's why I want to see the white papers on the issue.

  I know the 1.5 x RAM is old school and should not really be applied to the most recent operating system (especially 64-bit) but even if they exchange 2010, RRAS and web/FTP servers, they literally nothing 95% of the time.

  TIA.

  Alceryes wrote:

  I know the 1.5 x RAM is old school and should not really be applied to the most recent operating system (especially 64-bit) but even if they exchange 2010, RRAS and web/FTP servers, they literally nothing 95% of the time.

  I really think it's the old school as you say. The 1.5 x RAM always comes to a number which was 'stuck' as something good and useful, but which is really just arbitrarily number that doesn't say. You would no doubt minimum performance by static gain this setting.

  Modern Windows operating systems is not heavy on the use of the swap file in any case and with a small approval like this, they won't have to do much all internal Exchange. Keep an eye on the host balloon status, if it is high the VMs, pourrait be forced to do paging.