Send to user datetime is authenticated via headervar

Similar Questions

• The number of devices (MAB) can be authenticated via the internal identity stores ACS 5.3? ACS 1120 (802.1 x))

  Hello

  I m currently looking for a document that specify the number of MAC addresses can be stored and authenticated via a GBA (1120)? I prefer to use the identity store internal AD or LDAP for authentication of the MAB for 802.1 X project.

  I would like to know what impact the GBA? CPU/MEM?

  What is the impact on the user authentication? delay, delay, etc.

  Please specify any other restrictions or side effect.

  Thanks for your comments

  Concerning

  Torsten Hello,

  I have confirmed on our database as well as this community and the answer is the same

  Refer to:

  https://supportforums.Cisco.com/thread/2101657

  Added additional information:

  Internal Users : 300000 Internal Hosts : 50000

  Best regards.

• user with external authentication

  Hello!
  
  The DB is running on AIX.
  AIX uses the single sign on with MS Active Directory.
  
  Is it possible for users to start the application on a Windows PC here and connect to the DB using MS AD password here?
  Or even without any password at all?
  
  I created a user ops$ myuser, myuser is an AIX user authenticated via MS AD.
  I can connect to AIX with "sqlplus / ' without being prompted to enter the password.
  
  But when I try to connect to the DB with this my Windows PC user authentication does not work.
  
  Someone at - it experience with this constellation?
  
  BTW, we do not have Oracle Internet Directory
  
  BR
  Daniel
  
  Published by: user641444 on May 19, 2011 06:04

  I have a similar setup and it had worked, connect Windows 'sqlplus /@connect_string_database' worked well against the database unix/vms.

  Maybe problem with domains or subdomains or database such as remote_os_authent parameter (set it true)

  HTH
  Antonio NAVARRO

• What trigger is fired when the user closes a Web via cross sign which is in the upper right

  Dear all,

  I have a form that requires a separate canvas. Please tell me what trigger is fired when user close a canvas via cross sign that exists in the upper right (the sign of the cross appear as the corresponding window contains the property of: close the permit YES).

  Concerning

  Rajat

  Never heard of a trigger key to closing.

  As they said above, when you close a window, CLOSING of WINDOW-WHEN trigger fires.

  There you can examine the value of the: system.event_window, which bears the name of the window that fired the trigger.

  A typical use of this must publish a Do_Key ('EXIT_FORM') in your when relaxation window closed

  You don't need to check the: system.event_window, you can have several KEY-RELEASE triggers at various levels if necessary and they will attack the function of closing the window.

• How to prevent the login page in the same browser when the user is already authenticated

  Hello

  I use Jdev 11.1.1.6 with ADF implemented in my application security.

  I have Login.jspx that redirects the user to Home.jspx on a successful authentication. The user can either enter the URL of the Home Page or Login.

  Please consider the following scenarios:

  (a) the user is not authenticated in the current browser session

  (a.1) if the user enters the URL of the home page and the login page is displayed and redirected to the homepage on authentication

  (a.2) if the user enters the login page URL, then the login page is displayed and redirected to the homepage on authentication

  (b) the user is already authenticated in the current browser session, a new tab opens and

  (b.1) if the user enters the URL of the homepage then it shows directly the (already authenticated) Homepage

  (b.2) if the user enters Login URL then connect a page appears - This is the issue, it should either user to the homepage or invalidate the existing session and let users to proceed again.

  How do I get there? Any help is appreciated.

  Thank you

  JAI

  Hello

  the authentication check must be in a phase listener or servlet filter. If you use a phase listener and the homepage and login have a link associated with the ADF (PageDef file) then in the phase AFTER RESTORE_VIEW, you can use AdfContext.getCurrent () .getSecurityContext () .isAuthenticated () to tell if a user is authenticated or not.

  Frank

• Bug report: application process runs even if the user is not authenticated.

  Hi all
  
  I just stumbled on something that looks like a bug or a security problem for me:
  When you have an application at a point 'Load - before the header (header of page template)' this process is executed no matter if a user is logged on or past validates a session ID in the URL.
  
  
  Example:
  In my Application, I have an application process to download a file when a certain application is defined. I chose the application process to hide the url/location of the user files and make sure that this file can only be downloaded in an application context (thank you Dene for inspiration: [http://apex.oracle.com/pls/otn/f?p=31517:15]). This works really well and did all the things I want to do.
  But then I tried to call my download URL (for example http://myhost:myport / mytest/pls/f? p = 1234:0:123123123123:DOWNLOAD_FILE:NO ::) from another computer without logging in.) I expected to get the login screen of my application and all my pages require authentication, but I got the file.
  
  To work around this problem, I put in condition of the pl/sql process ": APP_USER IS NOT NULL AND: ASK 'DOWNLOAD_FILE' = ', now it works as expected and shows the login page if the user is not authenticated or given to the session id is null/not valid."
  
  
  I am mistaken and that the process should not run? I put same authorization "must not be public user" who has been ignored as well.
  
  Peter

  Peter and Dene,

  Thank you for this comment. I agree that this is a bug and we'll fix it. A solution you can set the attribute Public user of your application to PUBLIC_USER. As long as your FATHER connects as apex_public_user it shouldn't break anything.

  Scott

• Separation of monitor only and Admin for Cisco ASDM (ASA) access for users authenticated via LDAP

  Hello

  We have two groups of ads on network Admins, one for the system administrators group. The network Admins will get Priv lvl 15 the other Priv lvl 3.

  This is the setup I use:

  TestASA # sh run ldap-attribute-map of test4
  Comment by card privileged-level name
  map-value comment fw - ro 5
  map-value comment fw - rw 15
  memberOf IETF Radius-Service-Type card name
  map-value memberOf "cn = s-FW-Admin, OR = security groups, DC = 802101, DC = local" 6
  map-value memberOf "cn = s-fw-ro, OR = security groups, DC = 802101, DC = local" 5

  The user in both groups can connect ssh and asdm but all users get the same rights priv lvl 15.

  Someone at - it an idea?

  You must visit the listed link below to configure ASA to only read access and access admin. not sure, if you have already been there.

  https://supportforums.Cisco.com/docs/doc-33843

  ~ BR
  Jatin kone

  * Does the rate of useful messages *.

• ISE Sponsor authentication via RADIUS

  My client demand change us the way the sponsor users are authenticated and authorized to access portal Sponsor of ISE.

  Their similar to the request of the ISE AD via a RADIUS server first. They said "avoid sending credentials of the AD to ISE directly. Under this condition,.

  My research and limited knowledge give to assume I have to define a RADIUS Proxy

  I think I can define an external RADIUS server, but I wonder if this creation, it would be available as a Source of identity for "portal Sponsor sequence.

  If this is not the case, how can I add this? After that, what conditions or attributes should I look for to use in the 'strategy of group sponsor' in order to filter the name of user and password and allow access to employees and deny access to everyone?

  I'd appreciate advice that you can give me to offer the best recommendation to the client.

  Kind regards.

  Daniel Escalante.

  Hi sliman,.

  Unfortunately, this document is not relevant to what Daniel is trying to achieve.  There need to be able to refer to a RADIUS server as part of the Sponsor authentication process, that is not possible today.  The only possibilities are that I have indicated in my original answer.

  Richard

• A problem when authentication via Radius ASA

  Hi all

  Please give me a helping hand. I have a problem when through ASA 5520 via Radius Authentication for ACS 4.0 via the VPN device. I need to configure secure authentication and NAC for remote user VPN. It simply does not work, but it works when you use Ganymede so all the connection seems to be ok as ACS succesfully authenticate a remote via MS AD VPN user when you use Ganymede. But I read that I can not use NAC when Ganymede using, I'm good? ASA and ACS journals indicate a problem with the shared key but I already double checked the key on both sides, the IP address is correct on SAA and I also tried all possible methods of RADIUS on SAA. Any idea where might be a problem?

  Hello

  When you use ACS 4.0, then make sure that the AAA Client for ASA entry you created on GBA, if under a NDG, then make sure that there is no key to the NDG level.

  Otherwise, pass entry client ASA as RADIUS ACS in NDG (Unassigned) on ACS.

  Kind regards

  Prem

• Send all users of iSupplier

  Is there a way to inform all users of iSupplier? We want to be able to inform all users of iSupplier when we take the system down for maintenance and would like to send an email to all users.
  
  Thank you
  Rob

  Let me take your questions one by one.

  How can you determine who is a user of the provider.
  -Users of the supplier are identified by the attribute setting 'ICX_SUPPLIER_CONTACT_ID '. The FND provider user must have this attribute, set the id of the vendor contact. If you are in R12, you can refer to the "PO_VENDORS_GRP.get_external_userlist" package for the code example.

  You basically set up a different alert for each email or did you just change the text each time.
  -It depends on how how to configure the alert. I don't know if you've met the alert screen; a simple way that it works is as below. You write a SQL that will take all the variables needed to send a notification. Then build the output of SQL-based notification. Variables (sql output) can replace anywhere in the object / the body of the notification (including the TO). So depending on how you build your SQL, the notification text, you can change the text through via alert sending. You can take a look at some of the seeded for example alerts.

  Buyers have access to it or must they rely on a system administrator to change the message and send it out
  -L' screen will open all alerts. So I don't think you want to expose the screen of definition of alert for all buyers. Rather, you might think of option enter the text of the message somewhere in the PO and as part of the SQL text extraction which must be communicated to the buyer.

  You can explore this little more; you will also have other options.

• Select the application element when the user is not authenticated.

  Hi, quick explanation just what I would do:
  
  I would like to allow the user to connect to the system and open the page that he or she has been redirected in edit mode.
  
  My application sends e-mail notifications to users. When user click on the link of the page opens (application allows anonymous access in the playback mode).
  
  The problem is that when users try to connect to the application, they are redirected to the home page.
  
  My intention is to create button Edit on the page. This button will be variable application with the "page url" value and redirect users to the login page.
  
  After login, the login process looks like this:
  
  (wwv_flow_custom_auth_std). Login
  P_UNAME = >: P101_USERNAME,.
  P_PASSWORD = >: P101_PASSWORD,.
  P_SESSION_ID = > v ('APP_SESSION').
  P_FLOW_PAGE = >: APP_ID | : F101_INITIAL_PAGE_NO
  
  );
  
  Where: F101_INITIAL_PAGE_NO is my point of application.
  
  I also created processes to define: F101_INITIAL_PAGE_NO if its value is null, so there is always the page to be redirected to.
  
  The problem I have is that I can not put point of application to the value I want to when I'm not authenticated. When I am authenticated everything works fine (I can request value set).
  
  The way I put the value of the element is:
  
  function setItemValue (item, value)
  {
  Alert (Item);
  Alert (value);
  get var = new htmldb_Get (null, & APP_ID., 'APPLICAITON_PROCESS = dummy', 0);
  Get.Add (Item, value)
  gReturn = get.get ();
  get = null;
  
  }
  
  My point of application is also unrestricted.
  
  All of the suggestions.
  
  Thanks in advance.

  get var = new htmldb_Get(null,&APP_ID.,'APPLICAITON_PROCESS=dummy',0);

  call page 0. This page is in your case probably fixed to "authentication: Page requires authentication. This is why it does not work.

  Denes Kubicek
  -------------------------------------------------------------------
  http://deneskubicek.blogspot.com/
  http://www.Opal-consulting.de/training
  http://Apex.Oracle.com/pls/OTN/f?p=31517:1
  -------------------------------------------------------------------

• Sending files to T450s Android phone via bluetooth

  Hello!

  I have associated my Samsung S3 Android phone with my newly bought T450s. I can easily send files to my phone by doing a right click on the file and choose to send it via bluetooth, but whenever I try to send it to my T450s from a phone I just get information which "cannot send the file" and I don't get any notification pop - up of any kind on my laptop.

  How can I solve this problem? I need to install additional software to receive files?

  P.

  Try this?

  http://plugable.com/2013/11/11/easy-way-to-use-Bluetooth-to-Exchange-files-with-your-phone-in-window...

  Comment to Moderator: Marked as the last answer to the OP is a response to this post...

• I can't send or receive e-mail messages via Outlook Express.

  I looked at some of the answers to other peoples questions and they do not help me.  I talked to my e-mail service provider and they tell me that the problem is in Outlook Express.  I want to solve this problem because I prefer to use Outlook Express to access and send e-mail messages.

  You specify what you have tried or what the problems are or what answers you looked to your situation.  None of us is clairvoyant, so some details would have us understand your situation.

  Search the antivirus interference with your e-mail account (see www.oehelp.com/OETips.aspx#3) disable any analysis of e-mail software antivirus and then remove your e-mail account, close and reopen OE and then add your e-mail account back again.  Also, check if you have the possibility, that the webmail access works very well to make sure that you have the right user name and password and that email servers are not problems.

  If this is not helping, so be specific in what concerns what isn't working and what error messages you download.

  Steve

• Foglight authentication via a URL

  Hi guys, can I somehow pass the details of authentication (username and password) in the URL?

  A customer asked me to create a dashboard tailored to its environment for Dept. IT can see situation... so I would share link dash at his stuff IT without that users must connect to the Foglight...

  Is this possible?

  It looks that you would like to use the NoLoginUser feature where you available to the user and configure your dashboard to provide an authorized role to NoLogin.

  This way you can share the link to the dashboard and let be accessible.

• Cisco ISE 1.1.2.145 Admin authentication via the LDAP protocol

  I have configured the LDAP protocol and able to retrieve our LDAP directory structure. Now, I'm trying to point authentication "Admin Access" Source 'External identity', which is the new LDAP IS I created. But I couldn't find an option to authenticate locally if for some reason the LDAP configuration does not work. I learned that the ISE can automatically return to local auth as external sources Idenitity are inaccessible. How can I test the LDAP authentication with breaking them our Admin Access? I thought to open two parallel sessions, one with Super Admin account Local and one with the domain account. But I noticed that ISE communication is smart enough for the closing session/connection no matter what other sessions in different browsers so, basically, I can't open two parallel sessions the same machine to test. Suggestions? or am I missing something here?

  Thanks in advance.

  Hi Srinivas,

  Even if you configure LDAP as a source of external identity of admin access, you can always internal relief without having locked. According to the ISE user guide:

  During the operation, Cisco ISE is designed to "fall back" and try to perform the internal identity database authentication, if the communication with the external identity store has not been established, or if it fails. In addition, whenever an administrator for which you have configured external authentication launches a browser and initiates a logon session, the administrator must still the option authentication of demand through the local Cisco ISE database by choosing 'Internal' to the Selector drop-down storage of identity in the Connect dialog box.

  http://www.Cisco.com/en/us/docs/security/ISE/1.1/user_guide/ise_man_identities.html#wp1351543

  Please see the attached screenshot by my lab ISE:

  

  I configured the admin authentication against AD, but I still see both 'Internal' and 'AD' at the time of the connection.

  I hope this helps.

  Thank you

  Aastha