Sending data using MDS

Similar Questions

• you want to send data using labVIEW to arduino using write visa and the process and to take action using arduino. A

  I want to send data using labVIEW to arduino using write visa and the process and to take action using arduino. After that, I want to arduino to send out necessary via a serial port to labVIEW which should be read using visa read and store in a chain. While I am able to write or read both individually, I can't do it consecutively. I used advanced read and write vi for checking my code, but nothing is helping. The wrong bed 'time delay before execution. " Please let me know where I can go wrong. Also is it possible to write code for hx711 using labVIEW

  1. you need not "\n" on your orders println().  This command adds an end of line character already in the message.

  2. you get the error because you have a loop around your reading.  After the first reading (well technically, the second because of you add an extra line end character), there is nothing left in the port.  As a result, you will get the timeout.

  3. you should really consider using a Structure of the event.  This way you just don't write and read when you press the Write button and you can also use the structure of the event to make the loop to stop.  I also go up to close the port inside the stop-> value Change event.

  

• sends data using excel

  Hi all
  
  Our users try to send data to essbase through Excel add-in, however, he got the following error message:
  
  "Reports of Mutiple by recovery is not supported.
  
  Any advice?

  Hello

  Try to extract the data for these combinations in the excel sheet, it would give an error.
  Problem is with the dimensions ordering sheet. See this combination when you pull results given by no error and then only try to lock and send data.

• How to send data in eloqua with using ajax?

  Hello

  someone tell me how to send data using ajax?

  Thank you

  Rahul

  Hi Rahul

  Using this code to send data to AJAX

  $.ajax({)

  URL: ' your action? elqformname = name of the form eloqua & elqSiteID = eloqua site ID',

  type: 'POST',

  data: "field name =" + document.getElementById('field_id').value + "="+ document.getElementById('field_id').value field name,

  success: {function (html)}

  }

  })

  Thank you

  edynamic expert Eloqua

• Troubleshooting for sending data of 16 sensors to an excel using the IO file worksheet

  Hello everyone. I'm taking 16 sensor data using multiple analog inputs. The device that I use is a 6210 USB data acquisition module and so far I have further complicated the cause of program, it seems to work when I run. I read that you can add multiple channels to a Daq Assistant and use just this one Daq Assistant for all sensors and use a separate signals function, but I don't know how to write code that can be used for the task of trying to send that data from all 16 of the sensors to an excellent spreadsheet file. If anyone can help by sending a file attached on how correctly, that would be great. I'll put the file attactched down below what I tried to do.

  Thank you for all your help.

  Start by saying 'never use the DAQ Assistant!'.  Instead, read this excellent summary of NOR-DAQmx that tells you how to do almost everything you need quickly and easily.  What I suspect you want to do is every moment, taste all 16 channels and bring them into a table of numbers I16 (or, if you have defined scales, as 16 slna in units, you set).  You can "wrap" your only playback function of data acquisition within a while or for loop of N samples (for example, until you press Stop), then take the (now 2D) array of N points of 16 channels, and write to Excel.

  First of all, to get the data in "better shape", using DAQmx.  Have you tried opening MAX and get data by using Test panels?  You can see how MAX can taste all 16 channels at once, at the current rate you specify, permanently?  You can use MAX to set the scales, and if you perform a task in MAX, you can (when configuring your DAQ VIs) pull down this task already defined-and-configured and have almost all of the configuration done for you by MAX (well, not really for you, but made by you when you have made and saved the task).

  Bob Schor

  P.S. - These lights on the front panel are a bit garish, aren't they?  But very pretty...

• ActiveX in BradySoft (CodeSoft) - what method/class/object I would use to send data to the form variable to BradySoft?

  Can what method/class/object I use to send data to the form variable to BradySoft? I have a basic configuration of BradySoft label and I want to send it data of variable shape (a serial number) from Labview ActiveX. I joined guide Brady ActiveX programmers, but can't understand what to use for that.

  P.S. I would call Brady or TekLynx tech support on this issue, but they have a strict policy while BradySoft supports ActiveX, but does not provide technical support assistance programming with it. I thought I would try the Forums OR.

  Just an update. I could get this to work myself after a few days of playing with it (I suppose that the best way to learn!). I have attached a sample VI for anyone interested. Can we Kudo ourselves?

• How to send data from the client to the server using tcp

  1. as I am new to watch I need help with sending data from client to server. I went through various examples of labview, but each of them also explains transfer of data to the client server. But I need help regardng send data from the server to the client.

  2.i would use the data type variant for sending my data.

  Can someone help me please. Thank you

  Regardless of the meaning. Once you have a connection each end allows it to send data to another. Just create what you want to look like interaction.

  Do you want the client sends a command that request data?
  How do you think the response data to look like?

  You can send variants, but probably not worth the effort.

  Mike...

• Using af:poll to refresh and send data in table page and bound to the data in ADF

  Hi all

  Today, I practiced component survey. I'm going with blog post.

  JDeveloper, Oracle ADF & amp; amp; Java: The use of af: poll to refresh and send data in the page and databound chart in ADF

  all feature fine work. but where I stuck in this stage

  • Start your application and make changes to database and see the new user interface in every 4 seconds.

  but reloaded data seems to be always 1.

  I make the changes 3 or four times in db.i may be able to see the changes. but data reloaded always showing me 1.

  public class Mbeans {
      private RichActiveOutputText activeoutputtext;
      private String refreshinfo;
      private int i = 0;
      private RichPanelCollection pcl;
  
  
      public Mbeans() {
      }
  
  
      public void setActiveoutputtext(RichActiveOutputText activeoutputtext) {
          this.activeoutputtext = activeoutputtext;
      }
  
  
      public RichActiveOutputText getActiveoutputtext() {
          return activeoutputtext;
      }
  
  
      public void polllistener(PollEvent pollEvent) {
          // Add event code here...
          BindingContext bindingContext = BindingContext.getCurrent();
          DCDataControl dc = bindingContext.findDataControl("AppModuleDataControl");
          AppModuleImpl am = (AppModuleImpl)dc.getDataProvider();  
          am.getEmployeesView1().executeQuery();
          i = i+1;
          refreshinfo =  "Data Reloaded-" + i+"  Total Row-->"+am.getEmployeesView1().getRowCount();
          AdfFacesContext adfFacesContext = AdfFacesContext.getCurrentInstance();
          adfFacesContext.addPartialTarget(pcl);
          adfFacesContext.addPartialTarget(activeoutputtext);
          
      }
  
  
      public void setRefreshinfo(String refreshinfo) {
          this.refreshinfo = refreshinfo;
      }
  
  
      public String getRefreshinfo() {
          return refreshinfo;
      }
  
  
      public void setPcl(RichPanelCollection pcl) {
          this.pcl = pcl;
      }
  
  
      public RichPanelCollection getPcl() {
          return pcl;
      }
  
  
      public void setI(int i) {
          this.i = i;
      }
  
  
      public int getI() {
          return i;
      }
  }
  

  Thank you

  HM, I do not have the sample

  What place is the bean in? It should be at least in viewScope...

  Timo

• Sending data and downloading a file using as3.

  Hello
  
  I have a job application form where I users basic info such as name, email, phone not with this I'm asking him to download his CV (file doc ang)
  
  How can I publish all the data on one subject. I use PHP on the backend.
  
  I can send data and download file separately. ISIT possible to download the file and submit data at a time.
  
  Can I send additional variables with the file reference object.
  
  

  Hi guys

  I found the solution to

  http://www.flepstudio.org/Forum/flepstudio-utilities/2265-email-form-pictures-Flash-CS3-pH p.html

  Take a peek inside.

  Thank you

• sending data and reading

  Well guys, I have a problem sending data here.

  When I did which is left in a loop, it works!

  But when I did what is the Chief while loop, I received a large number of values of fools.

  

  Could someone help me on this?

  The second loop, I had only a few simple calculations for the example. So don't you worry with math or anything so.

  In the logic... the good is that I receive the correct value in table annexed bouth. The only thing that will change is 3 last numbers!

  If anyane can help me on this, I'll be happy!

  EduU wrote:

  Well guys, I have a problem sending data here.

  When I did which is left in a loop, it works!

  But when I did what is the Chief while loop, I received a large number of values of fools.

  This is because you have a status of critical competition due to your use of local variables. In the second loop, the instance of the local variable is read before you actually wrote the new value of the indicator. You can browse this thread.

• Sends data from LaunchPad MSP430G2553 Labview

  Hi all

  So, I have a MSP430G2553 LaunchPad and I want to be able to send data to Labview via USB to UARTusing.

  What I do in the MSP430G2553?

  Well, I wrote code that whenever I press a button on the LaunchPad it I send hollow text USB using UART. Using a program on my PC that monitors my serial port, I can confirm that, whenever I press the button, the text comes to the PC. I was also able to send commands to the monitor (it has a 'send the command' field) to the MSP430. If the connection works fine, between LaunchPad and PC.

  What I did in Labview?

  On the piece attached "" Labview_MSP430. "» JPG"you can see my code. Whenever I click on the "VISA resource name" there is no COM. It is said that "Refresh", and even when I click on it nothing happens. As you can see in the file "Device_Manager.JPG" PC can see my device in COM3 MSP430.

  So my question is, what should I do for Labview can see my device COM3/MSP430G3553? And then, my correct code so that it can read the port series?

  What is important is that the com port is visible in MAX (Measurement and Automation Explorer) and for the port is visible, you must install the driver NI-VISA.

  In your code, you must also add the VISA configure the Serial Port. Replace the VISA open with her. Inside the loop, you should not use VISA bytes to the Serial Port. The msp code must be set up to add a newline of endpoints (i.e.) and simply set the number of VISAS read of bytes to an arbitrarily high number. Playback will be automatically terminated when the character is detected.

• "Unable to send data to the printer.

  I have a HP deskjet F4440 printer.  He has always fought linking to our Mac.  We restart the printer or the computer often to do print, but after doing one or the other it would work normally.  But now it doesn't connect at all.

  I uninstalled and reinstalled the printer.  I downloaded and installed the software from the apple support Hewlett-Packard printer.  I restarted my computer, uninstalled and reinstalled my printer.  It presents itself as "in use" but says "Unable to send data to the printer" when I try to send a simple text of pages for print test.  When I try to scan it shows that the scanner is connected, initially said "waiting for scanner", then 'scanner is not available' stops.

  Do you have any suggestions?  Thank you!!!

  Hi mandi820,

  Welcome to the HP Forums! I see that your HP deskjet F4440 printer has difficulty to connect to your Mac. I'm happy to help you with this problem of connection! I have a few questions for you:

  • What version of Mac OS X are you using? OS x: find your OS version and build information.
  • How is the printer connected? Wireless, or USB?
  • Can you make copies with the printer?
  • The cable is connected to a surge protector or directly on a wall outlet? Questions when it is connected to an uninterruptible power supply/Strip/surge protector power.
  • You can print a self-assessment report extended? Print a self-test report extended.

  Hope to hear from you and have a great day!

• Time increasing while sending data via http repeatedly on the storm

  Hi all!

  My application sends data (in general, this is a picture of ~ 1200 Kb) to the server via http.

  The data are sent ok, but the when I send data several times (without leaving the application) the time devoted to writing the data in the outputStream develops. On first use, it takes usually ~ 50 seconds, the second seconds of ~ 70, the third seconds from ~ 100... I see this problem only on the storm, others (Curve 8900, Bold, Tour) are OK. The url is used on Storm is: http://xxxxxxxxxxxxx.com/mobile/mobile.asmx;deviceside=true

  Here is the code snippet:

  private static WSResponse send(byte[] xmlBytes, WSResponseParser parser) throws Exception {
  
          HttpConnection connection = null;
      OutputStream outputStream = null;
  
         try {
              connection = (HttpConnection)Connector.open(WifiChecker.getURL(URL), Connector.READ_WRITE, true);
  
              connection.setRequestMethod(HttpConnection.POST);
              connection.setRequestProperty("Content-Type", CONTENT_TYPE);
              connection.setRequestProperty("Content-Length", String.valueOf(xmlBytes.length));
  
              outputStream = connection.openOutputStream();
  
              int offset = 0;
              int chunk = DATA_CHUNK_SIZE; // 1024
              int len = xmlBytes.length;
              while (offset < len) {
                  if (offset + chunk >= len) { // avoiding OutOfBounds Exception
                      chunk = len - offset;
                  }
                  outputStream.write(xmlBytes, offset, chunk);
                  offset += chunk;
              }
  
              xmlBytes = null;
  
              String response = getResponseAsSting(connection);
  
              WSResponse wsResponse = null;
              try {
                  wsResponse = parser.getWSResponse(response);
              } catch (Exception e) {
                  throw ApplicationException.invalidWsResponse();
           }
  
              if (!wsResponse.isSuccess()) {
                  throw new WSFailureException(wsResponse);
              }
  
              return wsResponse;
  
          } finally {
              IOUtils.safelyCloseStream(outputStream);
              IOUtils.safelyCloseStream(connection);
              if (xmlBytes != null) {
                  xmlBytes = null; // notify VM it can safely free the RAM
              }
          }
  

  I thought it may be a memory problem, so I manually cancel xmlBytes, but which does not solve the problem.

  Any ideas?

  Thanks in advance,

  Arhimed

  P. S.

  There is no question about Simulator, only on a real device of the storm.

  MSohm, thanks for your response.

  Fortunately, I have just fixed the problem. The problem was not in the code above, but in the code that made the xmlBytes. I converted bytes of the image base64 and looks like I did it dangerously on the use of the memory.

  Thanks again for your attention to this thread!

• problems with smartview 11.1.2.3:500 sending data

  Hello

  We have problems with smartview 11.1.2.3:500 submitting data. They go back to original. Everyone sees the same thing?

  In addition, is always available for 11.1.2.3:500 adds excel?

  We have seen similar problems in our previous version 11.1.1.13.

  Level zero member is not the only child of a parent - is not a problem of "implicit sharing.  Parents are generally never distinguished part.

  I suggest you check to ensure there is security access to write to the intersection.

  One thing you can do is use the tab Styles of cell color read only one color of cells and cells writable a different color.  In this way, you can check security and make sure that you pull a cell in writing until you try to send data.

  A second problem is perhaps that you have the same intersection listed twice on your worksheet.  If you do, it will keep the data in the last record.

  Hope that helps.

• Sends data Essbase BSO

  Good afternoon

  Our group currently uses cubes essbase ASO to do their planning and forecasting.  Data bases are mainly intended to be warehouses of data, users just want to be able to send their data and consolidated it on the fly, as they get them.  They do not want to perform calculations of database (we had cubes BSO years ago, but the time calc were too - that's why we went to ASO).  It works well, except that as you know, ASO sending is notoriously slow--it's getting to be a little problem.  Now, we have recently moved to the latest version of Essbase / Smartview and I was told that if you partition a cube a cube ASO BSO, you can send data to the OSB, and through transparent access partition by ASO and ASO aggregate child values in the OSB for parent ASO values when users make their retrieves.  Is this true?  If so, this may be a game changer for us.  I tried to do this before, but still had to calc the BSO cube first.  Can someone check it for me?

  Thanks and sorry for being long-winded

  Oh Cameron the error you see is to listen to me. In fact, I was going to put in the comment that you made about adding complexity to the equation having to send to a database but to report each other as much as before 11.1.2.3, you wouldn't be able to see the ASO cube within planning. you will need to use an Essbase connection in Smart View to get there. He has certainly material environment.

  As I said also kind of each environment is differenent. in the case of the OP, there need test what its users do and see which is the faster of the two. There are some efficiency gains in the partitions to bring in data blocks. The amount of data users send, the closer the two could be equal or one overshadow the other.