Several subnets in the site to Site VPN
Hi guys,.
I would like to set up a site of tunnel VPN stie with several subnets. I could not find a configuration which is my problem. I hope you can help me with the solution.
You can find my design network attach to this subject.
This is my setup on the ASA:
(1) NAT excemption for network traffic, go to the Site to site VPN.
NAT (MGMTLAN, INT STSVPN) static source 192.168.10.0 192.168.10.0 static destination 192.168.31.0 192.168.31.0
NAT (inside, INT STSVPN) static source 192.168.15.0 192.168.15.0 static destination 192.168.38.0 192.168.38.0
(2) the Accesslist with traffic to encrypt
object-group network 192.168.10.0
object-network 192.168.10.0 255.255.255.0
object-group network 192.168.15.0
object-network 192.168.15.0 255.255.255.0
the 192.168.38.0 object-group network
object-network 192.168.38.0 255.255.255.0
the 192.168.31.0 object-group network
object-network 192.168.31.0 255.255.255.0
object-group network STSVPN-LOCAL
Group-object 192.168.10.0
purpose of group - 192.168.15.0
object-group network STSVPN-US
purpose of group - 192.168.38.0
purpose of group - 192.168.31.0
ACL_STSVPN-US allowed extended ip access-list object-STSVPN-LOCAL object group STSVPN-American
(3) proposal phase 1
IKEv2 crypto policy 10
aes-256 encryption
sha256 integrity
Group 14
FRP sha256
second life 86400
(4) proposal phase 2
Crypto ipsec ikev2 proposal ipsec IKEV2-IPSEC-ESP-AES-SHA
Protocol esp encryption aes-256
Protocol esp integrity sha-256
(5) group tunnel
tunnel-group 4.4.4.4 type ipsec-l2l
tunnel-group 4.4.4.4 General attributes
Group Policy - by default-GrpPolicy-STSVPN-US
IPSec-attributes tunnel-group 14.4.4.4
IKEv2 remote-authentication pre-shared key abcd
IKEv2 authentication local pre-shared key abcd
GroupPolicy
Group Policy GrpPolicy-STSVPN-US internal
Group Policy attributes GrpPolicy-STSVPN-US
value of VPN-filter STSVPN-US
Ikev2 VPN-tunnel-Protocol
(5) crypto card
10 CM-STSVPN crypto card matches the address STSVPN-US
10 CM - STSVPN peer set 4.4.4.4 crypto card
card crypto 10 CM-STSVPN set ikev2 proposal ipsec IKEV2-IPSEC-ESP-AES-SHA
interface card crypto INT-STSVPN CM-STSVPN
Crypto ikev2 enable INT-STSVPN
/////////////////////////////////////////////////////////////////////
The router configuration:
(1) part SA
proposal of crypto ikev2 ki2. PROP
encryption aes-cbc-256
sha256 integrity
Group 14
IKEv2 crypto policy ki2. POL
proposal ki2. PROP
ikev2 KR1 encryption keys
peer ASALAB
address 2.2.2.2
pre-shared key local abcd
pre-shared key remote abcd
Profile of crypto ikev2 ki2. TEACHER
match one address remote identity 2.2.2.2 255.255.255.255
address local identity 4.4.4.4
sharing front of remote authentication
sharing of local meadow of authentication
door-key local KR1
(2) Transformset
Crypto ipsec transform-set TS. VPN2, esp esp - aes hmac-sha256-256
tunnel mode
(3) access-list
IP ACL extended access list. VPNIKE2
IP 192.168.31.0 allow 0.0.0.255 192.168.10.0 0.0.0.255
IP 192.168.38.0 allow 0.0.0.255 192.168.15.0 0.0.0.255
(5) crypto card
crypto CM card. 30 VPN ipsec-isakmp
defined peer 2.2.2.2
the transform-set TS value. VPN2
group14 Set pfs
ki2 ikev2-profile value. TEACHER
match address ACL. VPNIKE2
//////////////////////////////////////////////////////////////////////
This configuration is correct to allow both subnets on each side of the VPN tunnel to communicate with each other.
192.168.31.0 subnet cannot communicate with 192.168.10.0
192.168.38.0 subnet cannot communicate with 192.168.15.0
Hello Jay,
I went during the configuration of the two aircraft and noticed a few errors on the configuration of the SAA. Details here:
(1) the access list configured for VPN traffic is named ACL_STSVPN-US, however the address for correspondence configured on the map encryption uses a group of objects name instead:
address for correspondence card crypto 10 CM - STSVPN STSVPN-US
You must change this setting to avoid any problems with the negotiation of traffic:
no matching address card crypto 10 CM-STSVPN STSVPN-US
10 CM-STSVPN crypto card matches the address ACL_STSVPN-US
(2) you also have the same error on the configured vpn filter. However, you could not use the access list ACL_STSVPN-United States for VPN filter since the ASA will filter incoming packets only. In this case the appropriate ACL will be configured for remote network (ROUTER) to local networks (ASA). It will look something like this:
access-list VPN_filter extended permitted ip object-STSVPN-US group LOCAL STSVPN
access-list VPN_filter extended permitted ip object-STSVPN-US group LOCAL STSVPN
Group Policy attributes GrpPolicy-STSVPN-US
VPN-Filter VPN_filter value
Keep in mind that the VPN filter is in the rules that determine whether to allow or deny packets of data tunnelees coming through the device security, based on criteria such as the source, destination, and Protocol address address. If you want to use the IP Protocol, the filter will not make a difference.
(3) group 14 of the PFS is configured on the router crypto map, but not on the SAA. You need to even add it in the card encryption ASA or remove it from the router.
ASA:
card crypto 10 CM-STSVPN set group14 pfs
Router:
crypto CM card. 30 VPN ipsec-isakmp
No group14 set pfs
Hope this help you to raise the tunnel,
Luis.
Tags: Cisco Security
Similar Questions
-
Cisco ASA 5505 site for multiple subnet of the site.
Hello. I need help to configure my cisco asa 5505.
I set up a VPN between two ASA 5505 tunnel
Site 1:
Subnet 192.168.77.0
Site 2:
Have multiple VLANs and now the tunnel goes to vlan400 - 192.168.1.0
What I need help:
Site 1, I need to be able to reach a different virtual LAN on site 2. vlan480 - 192.168.20.0
And 1 site I have to reach 192.168.77.0 subnet of vlan480 - 192.168.20.0
Vlan480 is used for phones. In vlan480, we have a PABX.
Is this possible to do?
Any help would be much appreciated!
Config site 2:
: Saved
:
ASA Version 7.2 (2)
!
ciscoasa hostname
domain default.domain.invalid
activate the password encrypted x
names of
name 192.168.1.250 DomeneServer
name of 192.168.1.10 NotesServer
name 192.168.1.90 Steadyily
name 192.168.1.97 TerminalServer
name 192.168.1.98 eyeshare w8
name 192.168.50.10 w8-print
name 192.168.1.94 w8 - app
name 192.168.1.89 FonnaFlyMedia
!
interface Vlan1
nameif Vlan1
security-level 100
IP 192.168.200.100 255.255.255.0
OSPF cost 10
!
interface Vlan2
nameif outside
security-level 0
IP address 79.x.x.226 255.255.255.224
OSPF cost 10
!
interface Vlan400
nameif vlan400
security-level 100
IP 192.168.1.1 255.255.255.0
OSPF cost 10
!
interface Vlan450
nameif Vlan450
security-level 100
IP 192.168.210.1 255.255.255.0
OSPF cost 10
!
interface Vlan460
nameif Vlan460-SuldalHotell
security-level 100
IP 192.168.2.1 255.255.255.0
OSPF cost 10
!
interface Vlan461
nameif Vlan461-SuldalHotellGjest
security-level 100
address 192.168.3.1 IP 255.255.255.0
OSPF cost 10
!
interface Vlan462
Vlan462-Suldalsposten nameif
security-level 100
192.168.4.1 IP address 255.255.255.0
OSPF cost 10
!
interface Vlan470
nameif vlan470-Kyrkjekontoret
security-level 100
IP 192.168.202.1 255.255.255.0
OSPF cost 10
!
interface Vlan480
nameif vlan480 Telefoni
security-level 100
address 192.168.20.1 255.255.255.0
OSPF cost 10
!
interface Vlan490
nameif Vlan490-QNapBackup
security-level 100
IP 192.168.10.1 255.255.255.0
OSPF cost 10
!
interface Vlan500
nameif Vlan500-HellandBadlands
security-level 100
192.168.30.1 IP address 255.255.255.0
OSPF cost 10
!
interface Vlan510
Vlan510-IsTak nameif
security-level 100
192.168.40.1 IP address 255.255.255.0
OSPF cost 10
!
interface Vlan600
nameif Vlan600-SafeQ
security-level 100
192.168.50.1 IP address 255.255.255.0
OSPF cost 10
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
switchport access vlan 500
switchport trunk allowed vlan 400,450,460-462,470,480,500,510,600,610
switchport mode trunk
!
interface Ethernet0/3
switchport access vlan 490
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
passwd encrypted x
passive FTP mode
clock timezone WAT 1
DNS server-group DefaultDNS
domain default.domain.invalid
permit same-security-traffic inter-interface
permit same-security-traffic intra-interface
Lotus_Notes_Utgaaande tcp service object-group
UT og Frim Notes Description til alle
area of port-object eq
port-object eq ftp
port-object eq www
EQ object of the https port
port-object eq lotusnotes
EQ Port pop3 object
EQ pptp Port object
EQ smtp port object
Lotus_Notes_inn tcp service object-group
Description of the inn og alle til Notes
port-object eq www
port-object eq lotusnotes
EQ Port pop3 object
EQ smtp port object
object-group service Reisebyraa tcp - udp
3702 3702 object-port Beach
5500 5500 object-port Beach
range of object-port 9876 9876
object-group service Remote_Desktop tcp - udp
Description Tilgang til Remote Desktop
3389 3389 port-object range
object-group service Sand_Servicenter_50000 tcp - udp
Description program tilgang til sand service AS
object-port range 50000 50000
VNC_Remote_Admin tcp service object-group
Description Fra ¥ oss til alle
5900 5900 port-object range
object-group service Printer_Accept tcp - udp
9100 9100 port-object range
port-object eq echo
ICMP-type of object-group Echo_Ping
echo ICMP-object
response to echo ICMP-object
object-group service Print tcp
9100 9100 port-object range
FTP_NADA tcp service object-group
Suldalsposten NADA tilgang description
port-object eq ftp
port-object eq ftp - data
Telefonsentral tcp service object-group
Hoftun description
port-object eq ftp
port-object eq ftp - data
port-object eq www
EQ object of the https port
port-object eq telnet
Printer_inn_800 tcp service object-group
Fra 800 thought-out og inn til 400 port 7777 description
range of object-port 7777 7777
Suldalsposten tcp service object-group
Description send av mail hav Mac Mail at - Ã ¥ nrep smtp
EQ Port pop3 object
EQ smtp port object
http2 tcp service object-group
Beach of port-object 81 81
object-group service DMZ_FTP_PASSIVE tcp - udp
55536 56559 object-port Beach
object-group service DMZ_FTP tcp - udp
20 21 object-port Beach
object-group service DMZ_HTTPS tcp - udp
Beach of port-object 443 443
object-group service DMZ_HTTP tcp - udp
8080 8080 port-object range
DNS_Query tcp service object-group
of domain object from the beach
object-group service DUETT_SQL_PORT tcp - udp
Description for a mellom andre og duett Server nett
54659 54659 object-port Beach
outside_access_in of access allowed any ip an extended list
outside_access_out of access allowed any ip an extended list
vlan400_access_in list extended access deny ip any host 149.20.56.34
vlan400_access_in list extended access deny ip any host 149.20.56.32
vlan400_access_in of access allowed any ip an extended list
Vlan450_access_in list extended access deny ip any host 149.20.56.34
Vlan450_access_in list extended access deny ip any host 149.20.56.32
Vlan450_access_in of access allowed any ip an extended list
Vlan460_access_in list extended access deny ip any host 149.20.56.34
Vlan460_access_in list extended access deny ip any host 149.20.56.32
Vlan460_access_in of access allowed any ip an extended list
vlan400_access_out list extended access permit icmp any any Echo_Ping object-group
vlan400_access_out list extended access permit tcp any host NotesServer object-group Lotus_Notes_Utgaaande
vlan400_access_out list extended access permit tcp any host DomeneServer object-group Remote_Desktop
vlan400_access_out list extended access permit tcp any host TerminalServer object-group Remote_Desktop
vlan400_access_out list extended access permit tcp any host http2 object-group Steadyily
vlan400_access_out list extended access permit tcp any host NotesServer object-group Lotus_Notes_inn
vlan400_access_out list extended access permit tcp any host NotesServer object-group Remote_Desktop
vlan400_access_out allowed extended access list tcp any host w8-eyeshare object-group Remote_Desktop
vlan400_access_out allowed extended access list tcp any host w8 - app object-group Remote_Desktop
vlan400_access_out list extended access permit tcp any host FonnaFlyMedia range 8400-8600
vlan400_access_out list extended access permit udp any host FonnaFlyMedia 9000 9001 range
vlan400_access_out list extended access permitted tcp 192.168.4.0 255.255.255.0 host DomeneServer
vlan400_access_out list extended access permitted tcp 192.168.4.0 255.255.255.0 host w8 - app object-group DUETT_SQL_PORT
Vlan500_access_in list extended access deny ip any host 149.20.56.34
Vlan500_access_in list extended access deny ip any host 149.20.56.32
Vlan500_access_in of access allowed any ip an extended list
vlan470_access_in list extended access deny ip any host 149.20.56.34
vlan470_access_in list extended access deny ip any host 149.20.56.32
vlan470_access_in of access allowed any ip an extended list
Vlan490_access_in list extended access deny ip any host 149.20.56.34
Vlan490_access_in list extended access deny ip any host 149.20.56.32
Vlan490_access_in of access allowed any ip an extended list
Vlan450_access_out list extended access permit icmp any any Echo_Ping object-group
Vlan1_access_out of access allowed any ip an extended list
Vlan1_access_out list extended access permit tcp any host w8-print object-group Remote_Desktop
Vlan1_access_out deny ip extended access list a whole
Vlan1_access_out list extended access permit icmp any any echo response
Vlan460_access_out list extended access permit icmp any any Echo_Ping object-group
Vlan490_access_out list extended access permit icmp any any Echo_Ping object-group
Vlan490_access_out list extended access permit tcp any host 192.168.10.10 object-group DMZ_FTP
Vlan490_access_out list extended access permit tcp any host 192.168.10.10 object-group DMZ_FTP_PASSIVE
Vlan490_access_out list extended access permit tcp any host 192.168.10.10 object-group DMZ_HTTPS
Vlan490_access_out list extended access permit tcp any host 192.168.10.10 object-group DMZ_HTTP
Vlan500_access_out list extended access permit icmp any any Echo_Ping object-group
vlan470_access_out list extended access permit icmp any any Echo_Ping object-group
vlan470_access_out list extended access permit tcp any host 192.168.202.10 - group Remote_Desktop object
Vlan510_access_out list extended access permit icmp any any Echo_Ping object-group
vlan480_access_out of access allowed any ip an extended list
Vlan510_access_in of access allowed any ip an extended list
Vlan600_access_in of access allowed any ip an extended list
Vlan600_access_out list extended access permit icmp any one
Vlan600_access_out list extended access permit tcp any host w8-print object-group Remote_Desktop
Vlan600_access_out list extended access permitted tcp 192.168.1.0 255.255.255.0 host w8-printing eq www
Vlan600_access_out list extended access permitted tcp 192.168.202.0 255.255.255.0 host w8-printing eq www
Vlan600_access_out list extended access permitted tcp 192.168.210.0 255.255.255.0 host w8-printing eq www
Vlan600_access_in_1 of access allowed any ip an extended list
Vlan461_access_in of access allowed any ip an extended list
Vlan461_access_out list extended access permit icmp any any Echo_Ping object-group
vlan400_nat0_outbound to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.77.0 255.255.255.0
outside_20_cryptomap_1 to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.77.0 255.255.255.0
outside_20_cryptomap to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.77.0 255.255.255.0
access-list Vlan462-Suldalsposten_access_in extended ip allowed any one
access-list Vlan462-Suldalsposten_access_out extended permit icmp any any echo response
access-list Vlan462-Suldalsposten_access_out_1 extended permit icmp any any echo response
access-list Vlan462-Suldalsposten_access_in_1 extended ip allowed any one
pager lines 24
Enable logging
asdm of logging of information
MTU 1500 Vlan1
Outside 1500 MTU
vlan400 MTU 1500
MTU 1500 Vlan450
MTU 1500 Vlan460-SuldalHotell
MTU 1500 Vlan461-SuldalHotellGjest
vlan470-Kyrkjekontoret MTU 1500
MTU 1500 vlan480-Telefoni
MTU 1500 Vlan490-QNapBackup
MTU 1500 Vlan500-HellandBadlands
MTU 1500 Vlan510-IsTak
MTU 1500 Vlan600-SafeQ
MTU 1500 Vlan462-Suldalsposten
no failover
Monitor-interface Vlan1
interface of the monitor to the outside
the interface of the monitor vlan400
the interface of the monitor Vlan450
the interface of the Vlan460-SuldalHotell monitor
the interface of the Vlan461-SuldalHotellGjest monitor
the interface of the vlan470-Kyrkjekontoret monitor
Monitor-interface vlan480-Telefoni
the interface of the Vlan490-QNapBackup monitor
the interface of the Vlan500-HellandBadlands monitor
Monitor-interface Vlan510-IsTak
Monitor-interface Vlan600-SafeQ
the interface of the monitor Vlan462-Suldalsposten
ICMP unreachable rate-limit 1 burst-size 1
ASDM image disk0: / asdm - 522.bin
don't allow no asdm history
ARP timeout 14400
Global 1 interface (outside)
vlan400_nat0_outbound (vlan400) NAT 0 access list
NAT (vlan400) 1 0.0.0.0 0.0.0.0 dns
NAT (Vlan450) 1 0.0.0.0 0.0.0.0 dns
NAT (Vlan460-SuldalHotell) 1 0.0.0.0 0.0.0.0
NAT (Vlan461-SuldalHotellGjest) 1 0.0.0.0 0.0.0.0
NAT (vlan470-Kyrkjekontoret) 1 0.0.0.0 0.0.0.0
NAT (Vlan490-QNapBackup) 1 0.0.0.0 0.0.0.0 dns
NAT (Vlan500-HellandBadlands) 1 0.0.0.0 0.0.0.0
NAT (Vlan510-IsTak) 1 0.0.0.0 0.0.0.0
NAT (Vlan600-SafeQ) 1 0.0.0.0 0.0.0.0
NAT (Vlan462-Suldalsposten) 1 0.0.0.0 0.0.0.0
static (vlan400, external) 79.x.x.x DomeneServer netmask 255.255.255.255
static (vlan470-Kyrkjekontoret, external) 79.x.x.x 192.168.202.10 netmask 255.255.255.255
static (vlan400, external) 79.x.x.x NotesServer netmask 255.255.255.255 dns
static (vlan400, external) 79.x.x.231 netmask 255.255.255.255 TerminalServer
static (vlan400, external) 79.x.x.234 Steadyily netmask 255.255.255.255
static (vlan400, outside) w8-eyeshare netmask 255.255.255.255 79.x.x.232
static (Vlan490-QNapBackup, external) 79.x.x.233 192.168.10.10 netmask 255.255.255.255 dns
static (Vlan600-SafeQ, external) 79.x.x.235 w8 - print subnet mask 255.255.255.255
static (vlan400, outside) w8 - app netmask 255.255.255.255 79.x.x.236
static (Vlan450, vlan400) 192.168.210.0 192.168.210.0 netmask 255.255.255.0
(Vlan500-HellandBadlands, vlan400) static 192.168.30.0 192.168.30.0 netmask 255.255.255.0
(vlan400, Vlan500-HellandBadlands) static 192.168.1.0 192.168.1.0 netmask 255.255.255.0
(vlan400, Vlan450) static 192.168.1.0 192.168.1.0 netmask 255.255.255.0
static (vlan400, external) 79.x.x.252 FonnaFlyMedia netmask 255.255.255.255
static (Vlan462-Suldalsposten, vlan400) 192.168.4.0 192.168.4.0 netmask 255.255.255.0
static (vlan400, Vlan462-Suldalsposten) 192.168.1.0 192.168.1.0 netmask 255.255.255.0
static (vlan400, Vlan600-SafeQ) 192.168.1.0 192.168.1.0 netmask 255.255.255.0
static (Vlan600-SafeQ, vlan400) 192.168.50.0 192.168.50.0 netmask 255.255.255.0
static (Vlan600-SafeQ, Vlan450) 192.168.50.0 192.168.50.0 netmask 255.255.255.0
static (Vlan600-SafeQ, vlan470-Kyrkjekontoret) 192.168.50.0 192.168.50.0 netmask 255.255.255.0
static (Vlan450, Vlan600-SafeQ) 192.168.210.0 192.168.210.0 netmask 255.255.255.0
static (vlan470-Kyrkjekontoret, Vlan600-SafeQ) 192.168.202.0 192.168.202.0 netmask 255.255.255.0
Access-group interface Vlan1 Vlan1_access_out
Access-group outside_access_in in interface outside
Access-group outside_access_out outside interface
Access-group vlan400_access_in in the vlan400 interface
vlan400_access_out group access to the interface vlan400
Access-group Vlan450_access_in in the Vlan450 interface
Access-group interface Vlan450 Vlan450_access_out
Access-group interface Vlan460-SuldalHotell Vlan460_access_in
Access-group interface Vlan460-SuldalHotell Vlan460_access_out
Access-group interface Vlan461-SuldalHotellGjest Vlan461_access_in
Access-group interface Vlan461-SuldalHotellGjest Vlan461_access_out
Access-group vlan470_access_in in interface vlan470-Kyrkjekontoret
vlan470_access_out access to the interface vlan470-Kyrkjekontoret group
access to the interface vlan480-Telefoni, vlan480_access_out group
Access-group interface Vlan490-QNapBackup Vlan490_access_in
Access-group interface Vlan490-QNapBackup Vlan490_access_out
Access-group interface Vlan500-HellandBadlands Vlan500_access_in
Access-group interface Vlan500-HellandBadlands Vlan500_access_out
Access-group interface Vlan510-IsTak Vlan510_access_in
Access-group interface Vlan510-IsTak Vlan510_access_out
Access-group Vlan600_access_in_1 interface Vlan600-SafeQ
Access-group Vlan600_access_out interface Vlan600-SafeQ
Access-group Vlan462-Suldalsposten_access_in_1 Vlan462-Suldalsposten interface
Access-group Vlan462-Suldalsposten_access_out_1 Vlan462-Suldalsposten interface
Route outside 0.0.0.0 0.0.0.0 79.x.x.225 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout, uauth 0:05:00 absolute
x x encrypted privilege 15 password username
the ssh LOCAL console AAA authentication
Enable http server
http 192.168.210.0 255.255.255.0 Vlan450
http 192.168.200.0 255.255.255.0 Vlan1
http 192.168.1.0 255.255.255.0 vlan400
No snmp server location
No snmp Server contact
SNMP-Server Community public
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
card crypto outside_map 20 match address outside_20_cryptomap_1
card crypto outside_map 20 set pfs
peer set card crypto outside_map 20 62.92.159.137
outside_map crypto 20 card value transform-set ESP-3DES-SHA
outside_map interface card crypto outside
crypto ISAKMP allow outside
ISAKMP crypto enable vlan400
crypto ISAKMP policy 10
preshared authentication
3des encryption
sha hash
Group 2
life 86400
tunnel-group 62.92.159.137 type ipsec-l2l
IPSec-attributes tunnel-group 62.92.159.137
pre-shared-key *.
Telnet 192.168.200.0 255.255.255.0 Vlan1
Telnet 192.168.1.0 255.255.255.0 vlan400
Telnet timeout 5
SSH 171.68.225.216 255.255.255.255 outside
SSH timeout 5
Console timeout 0
dhcpd update dns both
!
dhcpd option 6 ip 81.167.36.3 81.167.36.11 interface Vlan1
!
dhcpd option 6 ip 81.167.36.3 81.167.36.11 outside interface
!
dhcpd address 192.168.1.100 - 192.168.1.225 vlan400
dhcpd option ip 6 DomeneServer 81.167.36.11 interface vlan400
dhcpd option 3 ip 192.168.1.1 interface vlan400
vlan400 enable dhcpd
!
dhcpd address 192.168.210.100 - 192.168.210.200 Vlan450
dhcpd option 6 ip 81.167.36.3 81.167.36.11 interface Vlan450
dhcpd ip interface 192.168.210.1 option 3 Vlan450
enable Vlan450 dhcpd
!
dhcpd address 192.168.2.100 - 192.168.2.150 Vlan460-SuldalHotell
dhcpd option 6 ip 81.167.36.3 81.167.36.11 interface Vlan460-SuldalHotell
dhcpd 192.168.2.1 ip interface option 3 Vlan460-SuldalHotell
dhcpd enable Vlan460-SuldalHotell
!
dhcpd address 192.168.3.100 - 192.168.3.200 Vlan461-SuldalHotellGjest
dhcpd option 6 ip 81.167.36.3 81.167.36.11 interface Vlan461-SuldalHotellGjest
dhcpd ip interface 192.168.3.1 option 3 Vlan461-SuldalHotellGjest
dhcpd enable Vlan461-SuldalHotellGjest
!
dhcpd address 192.168.202.100 - 192.168.202.199 vlan470-Kyrkjekontoret
interface of dhcpd option 3 ip 192.168.202.1 vlan470-Kyrkjekontoret
dhcpd option 6 ip 81.167.36.3 81.167.36.11 interface vlan470-Kyrkjekontoret
dhcpd enable vlan470-Kyrkjekontoret
!
dhcpd option 3 192.168.20.1 ip interface vlan480-Telefoni
dhcpd option 6 ip 81.167.36.3 81.167.36.11 interface vlan480-Telefoni
!
dhcpd address 192.168.10.80 - 192.168.10.90 Vlan490-QNapBackup
dhcpd option 6 ip 81.167.36.3 81.167.36.11 interface Vlan490-QNapBackup
dhcpd 192.168.10.1 ip interface option 3 Vlan490-QNapBackup
!
dhcpd address 192.168.30.100 - 192.168.30.199 Vlan500-HellandBadlands
dhcpd option 6 ip 81.167.36.3 81.167.36.11 interface Vlan500-HellandBadlands
dhcpd ip interface 192.168.30.1 option 3 Vlan500-HellandBadlands
dhcpd enable Vlan500-HellandBadlands
!
dhcpd address 192.168.40.100 - 192.168.40.150 Vlan510-IsTak
dhcpd option 6 ip 81.167.36.3 81.167.36.11 interface Vlan510-IsTak
dhcpd 3 ip Vlan510-IsTak 192.168.40.1 option interface
Vlan510-IsTak enable dhcpd
!
dhcpd address 192.168.50.150 - 192.168.50.199 Vlan600-SafeQ
dhcpd option 6 ip 81.167.36.3 81.167.36.11 interface Vlan600-SafeQ
Vlan600-SafeQ enable dhcpd
!
dhcpd address 192.168.4.100 - 192.168.4.150 Vlan462-Suldalsposten
interface option 6 ip DomeneServer 81.167.36.11 Vlan462-Suldalsposten dhcpd
interface ip dhcpd option 3 Vlan462-Suldalsposten 192.168.4.1
Vlan462-Suldalsposten enable dhcpd
!
!
!
!
type of policy-card inspect dns preset_dns_map
parameters
message-length maximum 512
!
context of prompt hostname
Cryptochecksum:x
: end
Site 1 config:
: Saved
:
ASA Version 7.2 (4)
!
ciscoasa hostname
domain default.domain.invalid
activate the password encrypted x
passwd encrypted x
names of
!
interface Vlan1
nameif inside
security-level 100
IP 192.168.77.1 255.255.255.0
!
interface Vlan2
nameif outside
security-level 0
PPPoE Telenor customer vpdn group
IP address pppoe setroute
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
switchport access vlan 15
!
interface Ethernet0/6
!
interface Ethernet0/7
!
passive FTP mode
DNS server-group DefaultDNS
domain default.domain.invalid
outside_access_in list extended access permit icmp any any disable log echo-reply
access extensive list ip 192.168.77.0 outside_1_cryptomap allow 255.255.255.0 192.168.1.0 255.255.255.0
access extensive list ip 192.168.77.0 inside_nat0_outbound allow 255.255.255.0 192.168.1.0 255.255.255.0
pager lines 24
asdm of logging of information
Within 1500 MTU
Outside 1500 MTU
ICMP unreachable rate-limit 1 burst-size 1
ASDM image disk0: / asdm - 524.bin
don't allow no asdm history
ARP timeout 14400
Global 1 interface (outside)
NAT (inside) 0-list of access inside_nat0_outbound
NAT (inside) 1 0.0.0.0 0.0.0.0
Access-group outside_access_in in interface outside
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
Enable http server
http 192.168.77.0 255.255.255.0 inside
http 192.168.1.0 255.255.255.0 inside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
card crypto outside_map 1 match address outside_1_cryptomap
card crypto outside_map 1 set pfs
peer set card crypto outside_map 1 79.160.252.226
card crypto outside_map 1 set of transformation-ESP-3DES-SHA
outside_map interface card crypto outside
crypto ISAKMP allow inside
crypto ISAKMP allow outside
crypto ISAKMP policy 10
preshared authentication
3des encryption
sha hash
Group 2
life 86400
Telnet 192.168.77.0 255.255.255.0 inside
Telnet timeout 5
SSH timeout 5
Console timeout 0
VPDN group Telenor request dialout pppoe
VPDN group Telenor localname x
VPDN group Telenor ppp authentication chap
VPDN x x local store password username
dhcpd outside auto_config
!
dhcpd address 192.168.77.100 - 192.168.77.130 inside
dhcpd dns 192.168.77.1 on the inside interface
dhcpd option 6 ip 130.67.15.198 193.213.112.4 interface inside
dhcpd allow inside
!
dhcpd option 6 ip 130.67.15.198 193.213.112.4 outside interface
!
tunnel-group 79.160.252.226 type ipsec-l2l
IPSec-attributes tunnel-group 79.160.252.226
pre-shared-key *.
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
!
global service-policy global_policy
context of prompt hostname
Cryptochecksum:x
: end
Hello
The addition of a new network to the existing VPN L2L should be a fairly simple process.
Essentially, you need to add the network of the Crypto present ACL configurations "crypto map" . You also need to configure the NAT0 configuration for it in the appropriate interfaces of the SAA. These configurations are all made on both ends of the VPN L2L connection.
Looking at your configurations above it would appear that you need to the following configurations
SITE 1
- We add the new network at the same time the crypto ACL and ACL NAT0
access extensive list ip 192.168.77.0 outside_1_cryptomap allow 255.255.255.0 192.168.20.0 255.255.255.0
access extensive list ip 192.168.77.0 inside_nat0_outbound allow 255.255.255.0 192.168.20.0 255.255.255.0
SITE 2
- We add new ACL crypto network
- We create a new NAT0 configuration for interface Vlan480 because there is no previous NAT0 configuration
outside_20_cryptomap_1 to access extended list ip 192.168.20.0 allow 255.255.255.0 192.168.77.0 255.255.255.0
Comment by VLAN480-NAT0 NAT0 for VPN access-list
access-list VLAN480-NAT0 ip 192.168.20.0 allow 255.255.255.0 192.168.77.0 255.255.255.0
NAT 0 access-list VLAN480-NAT0 (vlan480-Telefoni)
These configurations should pretty much do the trick.
Let me know if it worked
-Jouni
-
Help the Site VPN Site PIX 501
Hello
I'm pretty new to PIX firewall, so I hope someone here can help me.
I have two PIX and try to create a private network virtual between the two PIX. I posted the configs below.
The problem is that I can ping PIX on a PIX two, but I can't ping the servers behind TWO PIX. On two PIX, I cannot ping PIX ONE or all the servers behind it.
Any advice would be appreciated.
Thank you
PIX 1
6.2 (2) version PIX
ethernet0 nameif outside security0
nameif ethernet1 inside the security100
hostname TMAXWALES
domain ciscopix.com
fixup protocol ftp 21
fixup protocol http 80
fixup protocol h323 h225 1720
fixup protocol h323 ras 1718-1719
fixup protocol they 389
fixup protocol rsh 514
fixup protocol rtsp 554
fixup protocol smtp 25
fixup protocol sqlnet 1521
fixup protocol sip 5060
fixup protocol 2000 skinny
names of
inside_outbound_nat0_acl ip 192.168.254.0 access list allow 255.255.255.0 192.1
68.1.0 255.255.255.0
outside_cryptomap_20 ip 192.168.254.0 access list allow 255.255.255.0 192.168.1
.0 255.255.255.0
pager lines 24
interface ethernet0 10baset
interface ethernet1 10full
Outside 1500 MTU
Within 1500 MTU
IP address outside of *. *.198.139 255.255.255.248
IP address inside 192.168.254.1 255.255.255.0
alarm action IP verification of information
alarm action attack IP audit
location of PDM 192.168.254.10 255.255.255.255 inside
location of PDM 192.168.1.0 255.255.255.0 outside
history of PDM activate
ARP timeout 14400
Global 1 interface (outside)
NAT (inside) 0-list of access inside_outbound_nat0_acl
NAT (inside) 1 0.0.0.0 0.0.0.0 0 0
Route outside 0.0.0.0 0.0.0.0 *. * 1.198.137
Timeout xlate 03:00
Timeout conn 0 half-closed 01:00:10: 00 udp 0:02:00 CPP 0: h323 from 10:00 0:05:00 TR
p 0:30:00 sip_media 0:02:00
Timeout, uauth 0:05:00 absolute
GANYMEDE + Protocol Ganymede + AAA-server
RADIUS Protocol RADIUS AAA server
AAA-server local LOCAL Protocol
Enable http server
http 192.168.254.10 255.255.255.255 inside
No snmp server location
No snmp Server contact
SNMP-Server Community public
No trap to activate snmp Server
enable floodguard
Permitted connection ipsec sysopt
No sysopt route dnat
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
outside_map 20 ipsec-isakmp crypto map
card crypto outside_map 20 match address outside_cryptomap_20
card crypto outside_map 20 peers set *. *.198.138
outside_map crypto 20 card value transform-set ESP-3DES-SHA
outside_map interface card crypto outside
ISAKMP allows outside
ISAKMP key * address *. *.198.138 netmask 255.255.255.255 No.-xauth non - co
Nfig-mode
part of pre authentication ISAKMP policy 20
ISAKMP policy 20 3des encryption
ISAKMP policy 20 chopping sha
20 2 ISAKMP policy group
ISAKMP duration strategy of life 20 86400
Telnet timeout 5
SSH timeout 5
Terminal width 80
PIX 2
6.2 (2) version PIX
ethernet0 nameif outside security0
nameif ethernet1 inside the security100
hostname tmaxbangor
domain ciscopix.com
fixup protocol ftp 21
fixup protocol http 80
fixup protocol h323 h225 1720
fixup protocol h323 ras 1718-1719
fixup protocol they 389
fixup protocol rsh 514
fixup protocol rtsp 554
fixup protocol smtp 25
fixup protocol sqlnet 1521
fixup protocol sip 5060
fixup protocol 2000 skinny
names of
permit 192.168.1.0 ip access list inside_outbound_nat0_acl 255.255.255.0 192.168
. 254.0 255.255.255.0
permit 192.168.1.0 ip access list outside_cryptomap_20 255.255.255.0 192.168.254
.0 255.255.255.0
pager lines 24
opening of session
debug logging in buffered memory
interface ethernet0 10baset
interface ethernet1 10full
Outside 1500 MTU
Within 1500 MTU
IP address outside of *. *.198.138 255.255.255.248
IP address inside 192.168.1.1 255.255.255.0
IP verify reverse path to the outside interface
IP verify reverse path inside interface
the IP audit info action alarm reset drop
reset the IP audit attack alarm drop action
location of PDM 192.168.1.0 255.255.255.0 inside
PDM logging 100 information
history of PDM activate
ARP timeout 14400
Global 1 interface (outside)
NAT (inside) 0-list of access inside_outbound_nat0_acl
NAT (inside) 1 0.0.0.0 0.0.0.0 0 0
Route outside 0.0.0.0 0.0.0.0 *. * 1.198.137
Timeout xlate 03:00
Timeout conn 0 half-closed 01:00:10: 00 udp 0:02:00 CPP 0: h323 from 10:00 0:05:00 TR
p 0:30:00 sip_media 0:02:00
Timeout, uauth 0:05:00 absolute
GANYMEDE + Protocol Ganymede + AAA-server
RADIUS Protocol RADIUS AAA server
AAA-server local LOCAL Protocol
Enable http server
http 192.168.1.0 255.255.255.0 inside
http 192.84.7.111 255.255.255.255 inside
http 192.168.1.10 255.255.255.255 inside
No snmp server location
No snmp Server contact
SNMP-Server Community public
No trap to activate snmp Server
enable floodguard
Permitted connection ipsec sysopt
No sysopt route dnat
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
outside_map 20 ipsec-isakmp crypto map
card crypto outside_map 20 match address outside_cryptomap_20
card crypto outside_map 20 peers set *. *.198.139
outside_map crypto 20 card value transform-set ESP-3DES-SHA
outside_map interface card crypto outside
ISAKMP allows outside
ISAKMP key * address *. *.198.139 netmask 255.255.255.255 No.-xauth non - co
Nfig-mode
part of pre authentication ISAKMP policy 20
ISAKMP policy 20 3des encryption
ISAKMP policy 20 chopping sha
20 2 ISAKMP policy group
ISAKMP duration strategy of life 20 86400
Telnet 192.168.1.0 255.255.255.0 inside
Telnet timeout 50
SSH timeout 5
Terminal width 80
Can't see anything obviously wrong with the configs. You have these connected back to back on the same subnet, it looks that it even if you have xxx out IP addresses? If so it's maybe a routing problem, in what they send everything to the default gateway of xxx.x.198.137 rather than to the other.
Try to add a static route to the remote subnet to each PIX that points directly to the peer, so on PIX1 you should have:
Route outside 192.168.1.0 255.255.255.0 xxx.x.198.138
and on PIX2 do:
Route outside 192.168.254.0 255.255.255.0 xxx.x.198.139
and see if that makes a difference. Note that you wouldn't encounter this problem when these two PIX is on separate networks and uses the default gateway for all routing decisions.
If this still fails, run 'debug cryp isa' and ' debug cry ipsec "on the two PIX are trying to build a tunnel again, and then and send us the output.
Also, make sure your tests that you're rattling to a host behind a PIX to a host behind the other PIX, ping PIX to PIX or host because of PIX that won't test your VPN connection.
-
How can I get a SpryMenuBar update of several pages of the site changes?
I'm a relatively new Web site builder. I'm building a site in CS5 that will initially have about 10 to 20 pages, but constantly expand.
How can I have my SpryMenuBar changes feed to all of the pages on my site? I think I need to do something with the external css styles, but I can't understand it.
I used a template to create additional pages.
Thank you
Joshua
Hello
the new bad first: SPRY is outdated and is no longer officially supported by Adobe. (SPRY for example will not work on any touch screen.) So I / we recommend that you switch to a library jQuery for your other needs.
The good news: while brégent wrote you can use SSI directives. For this, David Powers made a great "recipe book". Still (!) you can find it:
http://foundationphp.com/tutorials/sprymenu/ssi.php.
Good luck!
Hans-Günter
-
Routing multiple subnets on a site to site VPN
What is the recommended solution to deliver several subnets on a site to site vpn? Each subnet requires its own policy or a policy can be used for one or more subnets if the remote site has several subnets? In addition, if the remote router has only two fastethernet interfaces, it'll work if one of the interfaces of subinterface configuration or router on a stick?
If you talk about static routing, you can simply add the routes and change the ACL for encrypted as a result traffic.
If you want to run a dynamic routing. you will then need to IPSEC VTI. Here is the link
http://www.Cisco.com/en/us/docs/iOS/12_3t/12_3t14/feature/guide/gtIPSctm.html#wp1063136
and although I did not use of subinterfaces for IPSEC VTI. but according to me, it will work.
-
Unable to connect to the site of wildtangent games
KServer questions?
After several weeks on the site of WildTangent Games, I am now unable to connect. I tried several times to the direction of their support staff with passwords provided by them. Now they say the problem is most likely an error in KServe (KClient, KStatus). Also, I have Norton AV and got no where with them. What is the problem and what can you do about it? I'm not savvy in computer science.
Hello
A K (including KServer, KClient, KHttp and KStatus) error message typically occurs when your computer attempts to communicate with our servers, but the security software installed on your computer prevents that the communication does not occur. I would say to contact the forum of Wild Tangent games below to submit your question. It would be better option for assistance.
http://Forum.WildGames.com/Hope the information is useful.
-
Lack of drop down in the Site Manager
I am designing the presentation for my layout of product e-commerce (Ecommerce BC and Muse) - watch the video support/training it is assumed that me several options in the Site Manager. I don't have Web Forms and email system.
I don't have a page; module templates, etc.
Any suggestions or knowledge available?
Thank you-
Hello
Please activate the edition online by going to my details > scroll down > enable editing online.
It would also depend on the plan of the site you have selected.
Thank you
Sanjit
-
Using the same set processing on several site to site VPN tunnels
Hi all. I have a rather strange situation about site-to-site VPN tunnel.
On the one hand, I have a PIX 501 and on the other end an ASA5505 and a tunnel set up between them.
The problem is that on the side of the PIX, I can't establish a tunnel, but when the traffic starts on the side of the ASA the tunnel established as usual.
I checked the configurations on both ends and keys, passwords, mirror that LCD seems OK. The only thing that comes to my attention, it's that I have the same set of transformation used for 2 different tunnel on the side of PIX.
Can I use the same set of transformation on several tunnels or should I set a different transformation for each tunnel? Could be the source of the problem?
Use it on PIX
card crypto set pfs group2
Or on ASA, use:
card crypto set pfs Group1
-
VPN site to Site - ASA to PIX - same subnet on the inside
Chaps,
I have a unusual scenario, whereby case I need a tunnel vpn site-to-site between a pix of cisco version 7 and version 8 cisco asa, which have the same subnet ip to each endpoint. Is it possible to create such a tunnel from site to site or do I change one of the remote endpoints?
Thank you
Nick
Hi Nicolas,.
To allow the traffic through the tunnel when having the same at both ends addressing scheme, you should NAT VPN traffic.
That is to say.
Site a 10.1.1.0/24 LAN
Site B LAN 10.1.1.0/24
The site config:
NAT permit list to access ip 10.1.1.0 255.255.255.0 192.168.2.0 255.255.255.0
(in, out) static 192.168.1.0 access-list NAT
license of crypto list to access ip 192.168.1.0 255.255.255.0 192.168.2.0 255.255.255.0
Site B config:
NAT permit list to access ip 10.1.1.0 255.255.255.0 192.168.1.0 255.255.255.0
(in, out) static 192.168.2.0 access-list NAT
license of crypto list to access ip 192.168.2.0 255.255.255.0 192.168.1.0 255.255.255.0
The idea is that Site A will to 192.168.1.0 translatefd when you go to Site B, and Site B will result to 192.168.2.0 when you go to the Site A.
Hope that makes sense.
Federico.
-
Cannot ping computers on the subnet remote site vpn while to set up
Hi all
I encountered a problem of site to site vpn for ping answered nothing of machines of remote subnet.
the ipsec tunnel is ok but I can ping the ASA distance inside the interface ip
Here is my scenario:
LAN1 - ASA5510 - ASA5505 - LAN2 - ordinateur_distant
LAN1: 192.168.x.0/24
LAN2: 172.25.88.0/24
remote_machine_ip: 172.25.87.30
LAN1 can ping to ASA5505 inside interface (172.25.88.1)
but cannot ping ordinateur_distant (172.25.87.30)
Inside of the interface ASA5505 can ping ordinateur_distant
LAN2 can ASA5510 ping inside the machines on LAN1 and interface
Is there something I missed?
Thanks much for the reply
I don't think it's something you really want to do.
If you PAT the whole subnet to LAN1 ip (192.168.1.0/24) to 172.25.249.1, then LAN2, will not be able to reach the specific host on LAN1, cause now, you represent the LAN1 network, with a single ip address.
So traffic will become a way from LAN1 can reach LAN2 and get the response of LAN2 through the PAT on 172.25.249.1
But LAN2, is no longer specific hosts LAN1 ip traffic, since you only have 172.25.249.1, to represent the subnet to LAN1.
If you still want to PAT the whole subnet to LAN1 (192.168.1.0/24) ip to 172.25.249.1, then you have to do outside the NAT.
http://www.Cisco.com/en/us/customer/docs/security/ASA/asa80/command/reference/no.html#wp1737858
Kind regards
-
Use the remote website via VPN site-to-site
Hi all
We have two sites, the site has and B. At site A, we have a Web site we want to share with all of site B. Currently, site B can access the site via the VPN site-to site on X 0, which is their LAN. Nothing outside X 0 cannot access or ping to the address.
We added access rules to allow access from the DMZ to this interface, but again, no ping and no communication at all. The other strange thing is that we see that no trip package for these access rules either.
Any help is appreciated. Thank you.
It seems that the demilitarized zone is not part of the VPN tunnel.
Can you confirm that the DMZ subnet is part of local destinations on the site B and a part of the local destinations on site?
Kevin
-
Site to site VPN - impossible to reach the other side ASA
Hello
Recently, I replaced a Juniper with a Cisco ASA 5505 firewall in a branch. This branch has a VPN site to another seat. Firewall at Headquarters is a Juniper and managed by third parties. I have configured the ASA and replaced Juniper. Everything at the Branch works, and can reach all subnets and servers. As the user is concerned, there is no problem.
But corporate headquarters, I am unable to reach this ASA on the interface of data or management. See the image, I am unable to ping or join a network 192.168.10.0 and 192.168.200.0 or any other subnet 10.15.8.0 to Headquarters. However, I can ping computers from branch office which is in the same subnet as the data interface.
You guys could help me as I need to reach the ASA headquarters branch. I welcome all networks on both sides inside and the external interface. I also created a NAT as below. Am I wrong configured NAT
NAT (inside, outside) static source DM_INLINE_NETWORK_4 DM_INLINE_NETWORK_4 HO_Subnets HO_Subnets non-proxy-arp-search of route static destination
!
NAT Dynamics obj_any interface of source to auto after (indoor, outdoor)DIWA
This information is useful. You try to SSH to the address inside or management? May I suggest that we focus for now on access to inside? After we get this working, we can watch access via the management.
It does not appear in what you posted, but I'm not sure if it might be something that you have removed before posting. Do you have configured access to the administration? If this is not the case, may I suggest that you add access management inside the config.
HTH
Rick
-
Which device to use for the site to site VPN
Hello
Can someone recommend some inexpensive VPN devices, which will be set up to connect a few VPN site to site (20-30) (each site should not exceed 5 to 10 computers. The sites will be equipped with different VPN devices (like Linksys regular or any other - just able to site IPsec VPN). What I need is for my main site and hope get some suggestions.
Thank you
Ashok
Hey Ashok
Well, I'd say the firewall Cisco ASA 5500-x and Cisco ISR / ASR, two supported VPN from Site to Site on several sites.
You can look into those if they meet your criteria.
Concerning
Véronique
-
RV180 restrict access to the Site to Site VPN
Hello
I'm trying to set up my network so that VPN traffic is routed only to a physical single on the RV180 port or to a certain subset of devices on a network.
I have a site to site vpn configuration in a Home Office and connect to the corporate network. The user has a couple of devices on the home network who need to access the corporate network.
We hope to leave his PC accessible to its home network and the corporate network, but limit other devices to access the vpn.
I think that I could do playing with the subnet, but I just can't get my head around it.
It must be something simpleish to do this, isn't there?
I'd appreciate any help you have.
Thank you
Gary
Hi boys, here's a hypothetical situation.
VLAN 1 is port 1
VLAN 2 is port 2
VLAN 1 has a switch connected to your local network of services
VLAN 2 has a switch to maintain your VPN.
The configuration of the port for each port would be the vlan respective unidentified.
You can disable the router in order to prohibit intervlan communication. But also, and especially, the vpn is a specific meaning, subnet, you specify the specific ip subnet on the config of the tunnel because the config include not a second subnet will not work it's traffic in the tunnel.
-Tom
Please mark replied messages useful -
How to pass the traffic of a site VPN S2S by ASA to another S2S VPN site?
I have a need for hosts on separate VPN networks connected to my ASA corp to communicate among themselves. Example: Host A site 1 a need to communicate with host B on the site 2. Both sites 1 & 2 are connected via the VPN S2S. I would get every site traffic to flow through the ASA at the other site. Where should I start my configuration? NAT? ACL?
I can ping each host in the network Corp. but cannot ping from one site to the other. I set up same-security-traffic permit intra-interface and addition of NAT and rules the ACL to allow/permit 1 Site to contact Site 2. When I do a trace of package through Deputy Ministers DEPUTIES, packets are allowed to pass. I read different that tell no NAT y at - it something at the other end of the VPN to do? should NAT and ACLs rules be mirrored? Just in case, a site is an instance of MS Azure VM and the other is a 3rd party VM instance.
On the HubASA, can I set up a new card encryption that selects the Site1 Site2 traffic and protect the traffic and value her counterpart Site2 public IP or just add this selection of traffic to the existing encryption card for the existing tunnel between HubASA and Site2?
Just add this traffic to the existing encryption card.
Remember that this should be added on three routers (two hubs and there has been talk).
Site1
CRYPTO ip access list allow
Site2 subnet > CRYPTO ip access list allow
subnet training3 > CRYPTO ip access list allow
subnet HUB > Site2
CRYPTO ip access list allow
Site1 subnet > CRYPTO ip access list allow
subnet training3 > CRYPTO ip access list allow
subnet HUB > Training3
CRYPTO ip access list allow
Site1 subnet > CRYPTO ip access list allow
Site2 subnet > CRYPTO ip access list allow
subnet HUB > HUB
CRYPTO_1 ip access list allow
Site1 subnet > CRYPTO_1 ip access list allow
Site1 subnet > CRYPTO_1 ip access list allow
Site1 subnet > CRYPTO_2 ip access list allow
Site2 subnet > CRYPTO_2 ip access list allow
Site2 subnet > CRYPTO_2 ip access list allow
Site2 subnet > CRYPTO_3 ip access list allow
subnet training3 > CRYPTO_3 ip access list allow
subnet training3 > CRYPTO_3 ip access list allow
subnet training3 > Each of these ACLs is attributed to their respective crypto cards. CRYPTO_1 is assigned the site1 crypto map, CRYPTO_2 is assigned to the site2 crypto card... etc.
I hope that's clear
In addition to this, you need to configure identity NAT / NAT provides both the HUB and the spokes of sites.
--
Please do not forget to select a correct answer and rate useful posts
Maybe you are looking for
-
I have an old airport express (used as an extender) and a Comcast cable modem. In order to get a signal on my iPhone (AT & T), I had a microphone AT & T cell. I can't use the microphone cell as there is only a single port ethernet on the modem. If I
-
I can't change my default search engine.
A few days ago, I was not careful enough by downloading an application from the internet. My landing page and my search engines have been change to webssearches.com. In addition, a toolbar has been installed. To remove the toolbar and clean the addon
-
where and how to get the new Firefox add - one of who is spying on us. Please mail to...
Heard speak adds the new on Fire Fox. Where and how to get the new Firefox add - one of who is spying on us. Please mail to maheshubhayakar at rediffmail.com edited by email address - moderator
-
Firefox crashed, and a message appeared on the Internet (I couldn't understand it, and I'm not able to remember). The problem seems serious, first of all, I scanned my registry with Registry Mechanic, and then I checked the status of my drive with Pe
-
Windows 8.1 itself affecting no.: 1 in the order of boot loader
I treated myself to a HP Envy 700-230EA at the end of week. I like to use a mixture of Windows and Linux (Opensuse) in a dual-boot system. I found the HP guide on how to install a 2nd o/s using a DVD (disable secure boot / enable start legacy / choo