SMU system controlled by PC

Similar Questions

• Tiara DAC supports SMU systems?

  Hello

  I want to know if it is possible to install and run the DIAdem on an SMU (chassis and controller) system, and use the DAC

  for a quick setup of measurement and installation. Does anyone have experience with this configuration?

  I know I could use Labview but for quick measurement configurations DAC in Diadem is quite perfect.

  Thanks in advance.

  Just to complete the Walters post above.

  Tiara DAC works with any hardware OR SMU which is taken in charge by NI MAX (measurement and Automation Explorer), including the global virtual channels. If you have Windows XP or later version on the SMU system, it works very well...

  Otmar

• Get the error when you try to manually create a restore point in Vista 32 - Bit - System - Protection of the system control panel. Got the unable to create the specified task

  Get the error when you try to manually create a restore point in Vista 32 - Bit - System - Protection of the system control panel.
  Got the unable to create the specified task

  Hello

  What is the exact error message received when the problem occurs?

  Methood 1:

  Auditor of file system (CFS) scan to fix all of the corrupted system files. To do this, follow the steps in the following link:

  How to use the System File Checker tool to fix the system files missing or corrupted on Windows Vista or Windows 7

  http://support.Microsoft.com/kb/929833 

  Method 2:

  You can start Windows Vista by using a minimal set of drivers and startup programs. This type of boot is known as a "clean boot". A clean boot helps eliminate software conflicts.

  I suggest to put the computer in a clean boot state, and check if the problem persists, see the link:
  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7
  http://support.Microsoft.com/kb/929135
  Note: See step 7; Reset the computer to start as usual after troubleshooting is performed.

  Method 3:

  You can temporarily disable the security software and check if the problem occurs. Check out the following link to do the same thing:

  http://Windows.Microsoft.com/en-GB/Windows-Vista/disable-antivirus-software

  Warning: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you need to disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network, while your antivirus software is disabled, your computer is vulnerable to attacks.

  I hope this helps! Let us know if you need more assistance.

• IF RIO system control resource

  Hello

  Control of resource if RIO is a typedef. I want to use a control with a style like the XP style or system. I find for the resource of visa but not for YEW - RIO.

  Where can I find or how can I make another control for my IF - RIO resource.

  Thank you

  I didn't, so I did!

  If anyone needs it, I put it here

• Windows xp professional sp3 general system control panel displays the wrong amount of system memory

  Have a Dell Optiplex GX280 running Windows XP Pro SP3 with 3.5 GB of memory. BIOS confirms the good memory installed, but the control panel > system > general tab displays only 2.99 GB of memory.  Is there a fix for this issue or Windows using only the first 3 GB of memory?

  If you have Windows XP with service pack 3 - it's a 32-bit operating system.  The most he could use is 4 GB and some of which will be used for overhead costs.  The most I've seen Windows XP with SP3 report was 3.85 GB of memory - although it is more common to see a 3.25 and 3.5 GB.

  Memory shared (with a video device) can also take off the total.  It's usually anywhere from 64 MB to 1 GB if the video device uses the system memory compared to (or in coordination with) committed memory.

  With Windows XP, however, have probably seldom got you much above 1.5 GB of memory space used without some graphics intense or video edition GOLD of virtual machines.  ;-)

  Essentially - there is unlikely to be anything to fix.  If you want to use/manage better memory, you need a 64-bit operating system (I'm not implying Windows XP 64-bit) and possibly a new video device.

• Icons disappear and tools/system control panels does not open.

  I have vista running on my laptop (not sure what version because I can't open anything).  Yesterday my icons disappeared and I can't open anything in the control panel or the system tools.  An update installed yesterday, but I don't know what it was.  It is relatively a new laptop.  I just bought this one when my old laptop (also Vista) did the same thing.  I tried the system restore, but I can't open that either.  I'm quite proficient with computers then give me your suggestions - advanced or not.

  If you cannot use the system restore, try this disk to use system restore.

  Download the ISO on the link provided and make a record of repair time it starts.

  Go to your Bios/Setup, or the Boot Menu at startup and change the Boot order to make the DVD/CD drive 1st in the boot order, then reboot with the disk in the drive.

  At the startup/power on you should see at the bottom of the screen either F2 or DELETE, go to Setup/Bios or F12 for the Boot Menu.

  When you have changed that, insert the Bootable disk you did in the drive and reboot.

  http://www.bleepingcomputer.com/tutorials/tutorial148.html

  Link above shows what the process looks like and a manual, it load the repair options.

  NeoSmart containing the content of the Windows Vista DVD 'Recovery Centre', as we refer to him. It cannot be used to install or reinstall Windows Vista, and is just a Windows PE interface to recovering your PC. Technically, we could re-create this installation with downloadable media media freely from Microsoft (namely the Microsoft WAIK, several gigabyte download); but it is pretty darn decent of Microsoft to present Windows users who might not be able to create such a thing on their own.

  Read all the info on the website on how to create and use:

  http://NeoSmart.net/blog/2008/Windows-Vista-recovery-disc-download/

  ISO Burner: http://www.snapfiles.com/get/active-isoburner.html

  It's a very good Vista startup repair disk.

  You can do a system restart tool, system, etc it restore.

  It is NOT a disc of resettlement.

  And the 32-bit is what normally comes on a computer, unless 64-bit.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  Carefully read all the:

  http://www.bleepingcomputer.com/tutorials/tutorial140.html

  Understanding Windows Update and Extras in Windows Vista at the link above.

   

  Remove the Vista updates; two ways to do this:

  1. a System Restore to before the updates:

  Click Start > programs > Accessories > system tools > System Restore > restore time/choose your own date > next

  If you use Norton, disable it before using the system restore.

  If it is impossible to enter the Normal Mode, do a Safe Mode system restore:

  Press F8 at the startup/power and the list of startup options, use THE ARROW key to select Safe mode > and then press ENTER.

  System restore steps according to the info above.

  Also:

  2. click on start > right click on computer > properties > Windows updates down the lower left corner > updates installed in the lower left corner in the next window

  > then click the one that you don't want > uninstall will appear at the top > uninstall it.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  In addition, on the page where you clicked "Installed updates", click on change settings at the top left corner it

  > Change update settings in the next page of AutoUpdate to "check for updates but let me choose etc" > OK ".

  When you take a look at pending updates, you can either download/install them one at the time, namely the update causing you problems.

  > or if you do not need an individual > right-click on > UAC prompt > hide it

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  For questions of Windows updates:

  Windows Update Forum:

  It's updated operating system Vista, upgraded installation and activate Forum.

  You will get the best help for any problem of Update/Service Pack in the Windows Update Forum; the link below:

  http://social.answers.Microsoft.com/forums/en-us/vistawu/threads

  When you repost here, kindly include the Error Codes, and exactly what is happening when you try to update.

  In this way, you will receive the best help.

  See you soon.

  Mick Murphy - Microsoft partner

• All-in-one HP Officejet J4540: stuck on 'System control' during the installation complete installation OfficeJet J4500 series on Windows 10

  Tried to install (OJ_AIO_J4500_Full_Win_WW_140_404 - 4.exe) according to the HP support page is the correct installation of installation Officejet J4540 on Windows 10.  Printer was working fine when I was on Windows 7 and I have upgraded to Windows 10 and of course the printer did not work.  A ran all HP recommended programs and never can get this printer is installed.  Installation always stalls at the "checking system".  He never goes to the 'preparation for the Installation System' and 'Install Software' and 'configure the product.  Don't ever go to this and I let it run for hours without success.  I uninstalled all HP and tried to re - install on 10 to win without success.  Lost a ton of time on it... Please give me a proven QA had the solution... Thank you!!

  Hello
  Follow the steps below and check if it solves the problem:

  1 open the Mcafee Virus and Spyware Protection software you are interested in, click on calendar and perform analyses. Click analysis in real time, and then click stop. Select until I restart the PC and confirm by clicking the button turn off.

  If you have any other security software, be sure to disable any real-time Protection during installation.

  Now, try to reinstall the HP software and check if the installation goes as planned.

  If the problem persists, run the following tool:
  FTP://ftp.HP.com/pub/Printers/datfileremover/installdatfileclean.exe

  And then run the installation file and check all difference

  Kind regards
  Shlomi

• System Control en embarrassing RMAN

  Hello
  
  on 10g R2 UNIX AIX,.
  
  
  
  How can I use the RMAN online ordering system:
  

  RMAN> host ls
  
  
  
  RMAN-00571: ===========================================================
  
  RMAN-00569: =============== ERROR MESSAGE STACK FOLLOWS ===============
  
  RMAN-00571: ===========================================================
  
  RMAN-00558: error encountered while parsing input commands

  Thank you.

  Try

  RMAN> host 'ls';
  
  test1  test2  test3
  host command complete
  

  Kind regards

  -wiZ

• Hard drive does not meet the system controls

  bad sectors on hard drive

  "How to perform disk error in Windows XP check"
    <>http://support.Microsoft.com/kb/315265 >

  HTH,
  JW

• BB 8830 blackBerry smartphones - "Eception exception: net.rim.device.api.system.controlled access exception.

  I bought a stowaway Shasta Bluetooth keyboard to use with my BB 8830. I installed the driver and software on the BB, but get the "Eception exception: net .rim... warning exception and crashes the program.» I just uninstalled my BB, reinstalled the latest version of the OS and reinstalled my applications. The problem is still there. No idea how I can eliminate the issue? Thanks in advance for your help.

  Maxxasman

  I went on the site and found the latest driver and software for the keyboard. Everything works! Thank you for helping me resolve this issue!

  Rich

• SMU remote system do not read file .lvm

  I try to get my remote system (SMU remote system) to send a signal of analog voltage by reading a file .lvm.

  I have a project in real time implemented, and under my remote system, I have a VI that is supposed to give a signal of analog voltage.

  The implementation of VI begins by reading a file position (.lvm). After that, it is connected to a DAQ assistant.

  I'm already sure that everything is connected properly, and that it is the right channel. The reason why I'm sure is because in the DAQ assistant window, I can click on "run" in order to send a test signal. I am able to capture this signal to test with an oscilloscope. Therefore, I am sure that the system is all set up correctly.

  Finally, I don't know if it's important, but the measure file he was reading is located in my host. I don't know if I deploy when the VI to the target, if the measurement file is sent to the remote system with the VI.

  I was wondering if someone could help me please.

  Thank you

  Leon

  Hi Leon,

  If I understand correctly, you are trying to read a file .lvm waveform data and send this waveform through your SMU system. What devices are specifically using (chassis, modules...)? What exactly happens when you run the VI? You see errors? If so, what are the codes that come with these errors? Additional information on what the file .lvm would be also useful. What are the functions you use to play the .lvm file?

  Kind regards

• The color control system

  Hi all

  y at - it a way to color a Boolean control system.

  I use a Boolean system control with "changes when you press on" mechanical Action. He wants her to be green when it is real and by default if the value False. But I am unable to color in the customization mode.

  How can I color it?

  Thank you

  Ritesh

  Controls from the system palette are color-matched to the theme of the operating system and cannot be changed.

  If you want to use custom colors use a control among other palettes.

• "APP-OFA-48289: unknown error when creating control systems (immobilization).

  Hello
  
  I have problem
  
  Navigator: Fixed Asset Manager > Setup > system > control systems
  
  When I tried to create in the system controls are error message:
  
  "APP-OFA-48289: unknown error." Please contact your system administrator. »
  
  
  OS: Linux
  EBS: Oracle R12.1.3
  Database: 10g
  
  
  Thank you
  
  Escaline

  Navigator: Fixed Asset Manager > Setup > active system > system controls

  When I tried to create in the system controls are error message:

  "APP-OFA-48289: unknown error." Please contact your system administrator. »

  OS: Linux
  EBS: Oracle R12.1.3
  Database: 10g

  Please see (APP-OFA-48289 unknown error when recording data in system controls form FAXSUSTL.) [ID] 966382.1).

  Thank you
  Hussein

• SMU Chassis or modules appearing does not in NI Instrument Driver Finder/connecte Intstruments

  New user, to debut with a chassis SMU-1073, controlled by a PC, with supply POWER 4113, 4145 SMU and 4071 modules DMM.

  I installed all the drivers from the supplied USB system and I can indeed see/control of the chassis and modules of NI MAX.

  When I try to see the modules Labview 2012 or 2014 (I'm looking for example VI to start) Instrument Driver finder does not show any chassis or modules.

  Looking for support OR but could find no generic "Here's how to start using this box OR $20,000 without flinching" first steps to help.

  So, I was hoping that it was a mistake and plug and play like the other instruments I connected and used. What I am doing wrong?

  

  Do not use the finder of the instrument. Use the help > examples of find and refer to material input and output. Be specific in listing of the drivers you have installed.

• SMU-1065 opened to the power

  Hello

  I have SMU - 1065 and it is a part of a large system the system controlled by a switch.

  I want the PXI Init (online) when I press the main power...

  I'm guessing there is a switch or a jumper inside the PXI, a know where or you can give me a link to a manual...?

  Hi Kobi Kalif,

  If I understand you correctly, you want to on your frame when your line is under tension of your chassis?  If you want to replace the power switch on your chassis, you can set the switch to disable on the back of your chassis to "manual".  This will allow your chassis to power on automatically as soon as the line is energized. To learn more about this option and other options, see the Article knowledge base I linked below.

  The PXI chassis remote power

  Characteristics and the NI SMU-1065 user manual

  G Brandon