Sound does not automatically pass between speakes and helmet.

Similar Questions

• Sound does not work on my computer and the 'secret' is not on. HE WORKS AT HIOME WHEN PLUGED IN MY SPEAKERS... IAM NOT HOME NOW GET OUT ON THE ROADL

  My sound does not work on my computer... It worked when pluged in my speakers at home... I'm not at home so no speakers and I can not get any sound. I checked mute and is not clicked on also the volume upward all the way. What else can cause the sound works do not? Help is greatly appreciated.

  BJ Gawle

  Hi B.J.Gawle,

  Method 1

  Looks like you're using a laptop and this would happen if the default audio device is not set to internal computer speakers.

  (a) open the Control Panel.

  (b) double click on the sounds and Audio devices icon.

  (c) click the Audio tab and under audio playback, select the audio device on the laptop.

  (d) click apply and restart the computer, check to see if it helps.

  Method 2

  If fails it above step then check out the link below and run the Fixit tool available, check if it helps.

  Diagnose and automatically repair audio playback problems

  http://support.Microsoft.com/mats/AudioPlayback/

• Table does not work correctly between LabView and TestStand

  I'm doing a TestStand program that reads data from a LabView VI.

  If I run the VI in LabView, it works perfectly well and generates a table with 18 points in length, the first 3 are numbers between 0 and 10 and the rest being-1 as I intended. Re-run the VI causes the re - initialize correctly and I get a new table that also meets my specifications.

  When I run the VI of TestStand, it works fine once, producing a table with 18 points, the first 3 are numbers between 0 and 10, and the rest is-1.

  If I run the VI in TestStand once again it increases the length of array in 18 each time. In so doing, it fails to write the new 3 numbers and just add - 1 in table 18 times. If I restart TestStand will work fine once more, he repeats the error if I re - run the VI. I don't understand why this is happening.

  I have re-product the error in a separate VI and the order, and I have attached an example in this post. The VI contains all the necessary information (if not, please say so and I will correct it), and TestStand sequence is configured to put all results, I would find useful in the report (as additional results).

  Your problem is your VI.   Specifically the comment nodes.  They initialize on the first call.  TestStand retains the VI in memory.  So when the VI is called again, the comments always nodes have their last value.  You will get the same results if you have VI your ArrayBuild.vi twice appealed.

  The way you use the feedback nodes, they really replace with Shift Registers.  I like your comment nodes, but since you pass the value of the node in the loop, the SHIFT registers are much more appropriate.  Just make sure you initialize your Shift Registers.

• Sound does not work on the computer and the volume icon does not appear in the system tray.

  Original title: my sound icon has disappeared from the taskbar.  The Control Panel indicates the sound is on, but I can't hear anything.  What happened and how do I get my sound back?

  Have a Toshiba laptop that always displays the lower icon audio in the right hand of the screen.  The sound icon has disappeared and I can't hear anything.  I check Contol Panel and sound, and he says it works and is turned up... but I can't hear a thing.  How can we retrieve icon of audio and how I can hear sound?

  Hello

  Thank you for your response.
  I did a "System Restore" and the icon reappeared, and the sound now works.
  I restarted the computer a couple of times, but that does not solve the problem.  Also, I went into the Panel and checked to see if the speakers were working and were lit, and they were.
  It wasn't until I did the restore of the system that the icon reappeared and the noise began to work again.
  Thank you.

• Satelite L750 does not automatically pass the headphone

  I've been messing around with audio on the laptop, and now when I plug headphones into the Jack the laptop no will automatically switch to the new output device.

  The only way I have found to spend it was to change for audio by default, but I have to spend the time I finished.

  Is there anyway to switch when it detects that a new output audio device is discovered.

  Thanks dan

  This thread would be useful?
  http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?MessageID=256895

  Go to the dashboard-> Realtek HD audio Manager
  In the upper right corner, there is a small yellow folder called "connector settings.
  There you can find the setting "enable pop-up dialog box, when the unit is plugged.
  Plug in a headset and select the option "headphones". Then the sound only through the headphones

• Sound does not work after installing new wireless keyboard and mouse

  I have windows xp Media Center installed the new logitech wireless keyboard and mouse, and now my sound does not work. The speaker light is on, the Device Manager does not show a conflict and said that everything works well, but still no sound. A friend has just installed a new microsoft wireless keyboard and mouse and is having the same problem so I know that's not new equipment. Does anyone else have this problem?

  Hi Red_t,

  Welcome to Microsoft Vista answers Forum!

  Thank you for visiting the website of Microsoft Windows Vista Community. The question you have posted is related to XP Media Center and would be better suited to the Windows XP community. Please visit the link below to find a community that will provide the support you want.

  Windows XP Media Center edition Discussions - http://www.microsoft.com/windowsxp/expertzone/newsgroups/reader.mspx?dg=microsoft.public.windows.mediacenter&lang=en&cr=US

  Thank you, and in what concerns:
  Swathi B - Microsoft technical support.
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Sound does not work in my Vista computer.

  Original title: Hello I need solving audio sound problems no need for pilots to soand but I bought this record registration of his friend's Audio microphone

  who had the same problem before selling it, he was using this compact computer Presario f700 with windows 8 pro iam woundering if I had just the befdore of windows or start them at the same time that windows vista would be reqinize drivers

  Hey Joe,

  As the sound does not work under Windows 8 and Windows vista, it may be a hardware problem.

  We will try the following solutions and check to see if the sound works.

  Tips for solving common audio problems

  http://Windows.Microsoft.com/en-in/Windows-Vista/tips-for-fixing-common-sound-problems

  Download and install the driver for your model of laptop vista.

  http://h20000.www2.HP.com/bizsupport/TechSupport/ProductList.jsp?locale=en_US&TaskID=135&prodSeriesId=3548233&prodTypeId=321957

  
  

  Note: If you use the 32-bit operating system, download and install the 32-bit drivers.

  If you use the 64-bit operating system, download and install the 64-bit drivers.

  Also check out the following link:
  No sound in Windows

  http://Windows.Microsoft.com/en-in/Windows/no-sound-help#no-sound=Windows-Vista&V1H=win8tab1&V2H=win7tab1&V3H=winvistatab1&v4h=winxptab1

  
  

  If the problem still persists contact support forum HP:

  http://h30434.www3.HP.com/PSG/

• EVGA Nvidia Geforce 8400 GS issues: [FIXED] screen and the sound does not [FIXED] virgins

  I have a HP Compaq dc5750 I just got an EVGA Nvidia Geforce 8400 GS, and I'm having a problem with it. I disassembled the computer cover and installed, replace the cover, turned on the computer and the monitor not power not on. So I decided that I had to disable the integrated graphics card (ATI Radeon Xpress 1150), then I added the card even once. Still happens... Monitor powers on without the new graphics card. My monitor is 8 years old and lacks a DVI port. I have to connect the monitor to the graphics card to make it work? I want just this card to work.

  UPDATE: white screen problem is fixed, but the sound does not (no audio installed device) even if the audio driver is installed

  Hello

  This kind of question is mainly caused by the sound card driver is not not compatible.  Contact the hardware manufacturer directly to confirm the driver is compatible or not.

  Test the issue with another pair of speakers or headphones, or you can plug the device of reading to another port to see the result.

  In the meantime, you can also see if the playback device is disabled. To do this, please check the following steps:

  1 Please, click Start-> Control Panel-> Sound.

  2. on the playback tab, right-click on the empty square and then click on "show disabled devices".

  3. check if your playback device is disabled. If so, right-click on it and click Activate.

  1. Please click Start, type services.msc and press ENTER.

  2. double-click on Windows Audio.

  3. click on the 'general' tab. Make sure the "Startup Type" is "automatic". Then please click on "Stop" under "Status of Service" to stop the service.

  4. click on "Start" under "Status of Service" to start the service.

  Reinstall the audio device

  1. click on start, type Device Manager, click on Device Manager to open it.

  2. expand ' audio, video and game controllers ".

  3. right click on your audio device, and then click on uninstall.

  4. check "delete the driver for this device".

  5. click on OK.

  6. after that, restart the computer, the device and the driver must be reinstalled automatically.

  Please check if the problem can be solved now.

  If the problem persists, please install the latest driver of sound card on the manufacturer.

  I found the problem... once again: I had to go to the BIOS and enable Audio integrated. My audio integrated uses Realtek High Definition Audio instead of Nvidia High Definition Audio.

• Satego P100-10F: Windows XP Lan, usb slots and the sound does not work

  Hello

  I have problems with windows vista, so I checked the forum to get information on the windows xp installation.

  I downloaded the drivers windows xp since the P100 Satellite (pspa6e), my only problem is that the LAN, usb slots and my sound does not work.

  I hope someone has a good idea for drivers or to install another driver I have sound and LAN on windows xp.

  Ty and Greetz

  See European driver of Toshiba.
  Here, you can try to install several drivers of different portable Satellite P100.
  Try all series.
  Fact is that some units of the Satellite P100 and Satego P100 series were delivered with the same features.
  Therefore, it should be possible to use the unique drivers of these series.
  Check all.

• update date and time for 3.6 numbers does not show the time and does not automatically update the date

  The 'update date and time"for numbers of 3.6 does not show the time and does not automatically update the date.  What should I do?  Thank you.

  Hi david,

  where do you find ' update of the date and time.

  Quinn

• Sound does not work. Under the properties of sounds and Audio, peripheral devices by default "sound" is grayed out.

  Original title: audio device problem
  just reinstalled windows xp.  Sound does not work.  Under the properties of sounds and Audio, peripheral devices by default "sound" is grayed out.  Microsoft Fix it, but the best I get is "do not set as default audio device.  The lack of sound recording does show a device.  Ideas?  BTW, I sometimes get static noises out of the speakers.

  Hello

  I suggest you to follow the steps from the link and check if it helps.

  No sound in Windows

  I hope this helps.

• When I unplug my headphones the sound does not go to my regular speakers and also the reverse happened... logitech headphones... HELP Please

  When I unplug my headphones the sound does not go to my regular speakers and also the reverse happened... logitech headphones... HELP Please

  Hi MaryLitrel,

  Follow the steps in the article.

  How to troubleshoot sound problems in Windows XP

  http://support.Microsoft.com/kb/307918/en-GB

  How to update a sound card driver in Windows Vista and Windows XP

  http://support.Microsoft.com/kb/166774

• My gesture control function does not work correctly there on and off automatically

  My gesture control function does not work correctly there on and off automatically

  which application you are using? try reinstalling the media gallery.

• Windows media player does not automatically open a video file on a Web site but I save it and open the file with Windows media player to play the video or audio recording.

  Windows media player does not automatically open a video file on a Web site but I save it and open the file with Windows media player to play the video or audio recording. I used to be able to play any video or audio file in any site!

  Hello

  Try resetting the default associations for WMP and IE.

  How to set default Associations for a program under Vista
  http://www.Vistax64.com/tutorials/83196-default-programs-program-default-associations.html
  How to associate a file Type of Extension to a program under Vista
  http://www.Vistax64.com/tutorials/69758-default-programs.html

  If necessary:

  How Unassociate a Type of Extension file in Vista - and a utility to help
  http://www.Vistax64.com/tutorials/91920-unassociate-file-extention-type.html
  Restore the Type Associations by default Vista file extensions
  http://www.Vistax64.com/tutorials/233243-default-file-type-associations-restore.html
  How to view and change an Extension of filename on Vista
  http://www.Vistax64.com/tutorials/103171-file-name-extension.html

  ====================================

  Also follow these steps:

  Follow these steps to remove corruption and missing/damaged file system repair or replacement.

  Run DiskCleanup - start - all programs - Accessories - System Tools - Disk Cleanup

  Start - type in the search box - find command top - RIGHT CLICK – RUN AS ADMIN

  sfc/scannow

  How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
  generates in Windows Vista cbs.log
  http://support.Microsoft.com/kb/928228

  Then, run checkdisk - schedule it to run at next boot, then apply OK your way out, then restart.

  How to run the check disk at startup in Vista
  http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

  ------------------------------------------------------------

  Then, if necessary:

  Have you recently installed another player?

  Reset your associations for WMP and IE.

  How to set default Associations for a program under Vista
  http://www.Vistax64.com/tutorials/83196-default-programs-program-default-associations.html
  How to associate a file Type of Extension to a program under Vista
  http://www.Vistax64.com/tutorials/69758-default-programs.html

  ---------------------------------------------

  Do this to reregister the Jscript.dll and Vbscript.dll files.

  Start - type in the search box - find command top - RIGHT CLICK – RUN AS ADMIN

  type or copy and paste-> regsvr32 jscript.dll
  Press enter

  type or copy and paste-> regsvr32 vbscript.dll
  Press enter

  Restart and if all goes well, it will run now.

  --------------------------------------------------------------

  Have you recently added stores or ANY application from Stardock?

  Using 64-bit Vista?

  Can you think of recent things you did in WMP which could be the cause? You added another
  reader recently or an add-on for WMP?

  When I try to use Windows Media Player 11, the program does not start, or some UI elements
  are empty - a Mr Fixit
  http://support.Microsoft.com/kb/925704/en-us

  Maybe something here
  http://msmvps.com/blogs/chrisl/articles/17315.aspx
  and here
  http://msmvps.com/blogs/chrisl/Archive/2004/10/30/17399.aspx

  Check here the news of WMP11
  http://zachd.com/PSS/PSS.html

  I hope this helps.

  I hope this helps.

  Rob - bicycle - Mark Twain said it is good.

• TB does not automatically download new messages email periodically even if "download automatically" is checked and set to 10 minutes

  TB does not automatically download new messages email periodically even if "download automatically" is checked and set to 10 minutes. Photo of the account server settings is attached.

  (For reference: it's POP, IMAP settings not.)

  Click the Advanced button under the settings above in the section "Message Storage" and review the when downloading mail on the server for this account, use the following folder to store new messages: settings.

  -Is selected Inbox for this account , and the record really / still exist? -If the second option (Inbox for the other account) is selected, make sure that the path is valid and that the box include this server when getting new messages is checked.