SPA9000 and PBX settings

Hello

I just get to work a spa9000 I want to use with trixbox installation.

in the spa9000 setup guide, it is write I have to change the settings of pbx.

But here's the problem: I don't have any PBX settings tab in admin and advanced mode voice SIP. Can somone help me solve this problem?

Photo:

Well finally it seems that I don't have a spa 9000... even if the firmware update to work properly, I have a spa 3102, that changes everything. Thanks for your reply.

Tags: VoIP Adapters

Similar Questions

  • SPA9000 And direct Ip calls?

    Hi, I just bought a SPA9000, and I wonder if I can set for direct ip calls.

    I use the FXS 1 on the spa9000 and line 1 is already on my VOIP provider.

    PBX settings
    Call the routing rule: (4xx<:L1>. |) <:L2>8xx. | <:L3>7xx. | <:L4>6xx.)

    And 1 line numbering Plan is:
    (<><:@mydynds.com:5061>xxxxxxx)

    Therefore, the call and the newspaper

    -----------------------------------------------------------------------
    [3] RegOK. NextReg in 58 (1)
    2. number of report 1 (1)(40 ms)
    Calling:[email protected]:6060
    [0:0] DIAL the ALLOC AUD (port = 16434)
    [0:0] RTP Rx upward
    [JIU] CallRoute:L144549141
    PRI--> INVITE--> pub
    Calling:[email protected]:5061
    Bcc:ringback / CallProgress 2
    CC:ringback
    [0:0] RTP Rx Dn
    Pub - 200--> CCI - 200--> pri (appeal)
    [0:0] ENC INIT 0
    [0:0] RTP Tx Up (pt = 0-> c0a80165: 16438)
    [0:0] RTCP Tx upward
    ----------------------------------------------------------------------
    But after some time 20 seconds or maybe less she then drops the call

    RespLooseMatch
    [0:0] 16 (2) LAT -.
    RespLooseMatch
    RespLooseMatch
    PRI says BCC GUEST: pri - 200--> CCI - 200--> pub
    CC: finished
    [0] alert FM stop RxTx (c = 002c67dc; a = 0)
    [0:0] call of Rel AUD
    359dc0 terminated DLG
    Sess end 3668ec
    TP Analyzer error: 34
    [0] on the hook

    -----------------------------------------------------------------------

    Any ideas?

    Thanks in advance.

    I tried to research on your problem and I found another element which may help us: Lets guess 2 devices and b. also allows assume address IP is 192.168.1.50 and B device IP address 192.168.1.51.

    Configure these settings in device A:

    Step 1: Line 1 tab, set port SIP SIP settings section: 5060.
    Stage 3: In line 1, Proxy and registration section all the empty fields or no. except to call without Reg: YES and years without Reg: YES.
    Step 5: Tab of row 1, section of subscriber information full name value: user ID: 11 and leave the other fields swamp.
    Step 7: In the tab section of plan Dial Dial Plan of line 1 on the Court together (21S 0<:@192.168.1.51:5060>), enable the IP numbering: YES

    Configure these settings in device B:

    Step 8: Line 1 tab, set port SIP SIP settings section: 5060.
    Step 10: In line 1, Proxy and registration section all the empty fields or no. except to call without Reg: YES and years without Reg: YES.
    Step 11: Tab of row 1, section of subscriber information full name value: user ID: 21 and leave the other fields swamp.
    Step 13: In the tab section of plan Dial Dial Plan of line 1 on the Court together (11S 0<:@192.168.1.50:5060>), enable the IP numbering: YES

    Now, how does it work:

    -To call device 1 line of device (any line) B dial 11.
    -To call device B line 1 of the device (one line) dial 21.

    This has proved works with two SPA phones that are configured in the same local network segment. But in you I thing deal you make IP dial in on a remote network that would probably be another network. In this case, I think that you must configure the VPN between the network where the SPA-9000 and the other phone remotely. Then configure the IP numbering as as it is done in the above procedures.

    I hope this helps.

  • I can not find where to change the privacy and security settings.

    I looked towards the top of the article about what said you to check / uncheck the boxes, but don't tell me where these boxes are.

    Hello

    1. Open the Firefox Preferences tab as follows: click the menu button

      and select Preferences.

    2. In the Firefox Preferences tab, click the Security tab (for Security and password settings) or Privacy (for confidentiality, and-not-track browsing history settings)

    Thank you.

  • This will remove all your custom settings and the settings of many extensions.

    Hello

    I was reading this article of knowledge and he says:
    "This will delete all your custom settings and many extensions settings."
    What are the custom settings?

    for example one of these and what else
    bookmarks?
    Add - ons?
    Top toolbar - Customize the toolbar
    Add on the toolbar
    Firefox/preferences
    Authorization Manager settings
    the new page open

    Corrupted preference file
    File preferences may be corrupt, Firefox prevents writing to it. If you delete this file, Firefox will automatically create another when it comes to.

    Here's how to delete the prefs.js file.

    This will remove all your custom settings and the settings of many extensions.
    Open your profile folder:

    In the menu bar, click the Help menu and select troubleshooting information. The troubleshooting information tab will open.

    In the section the Application databases, click view in the Finder. It will open a window with the folder of your profile.
    Note: If you are unable to open or use Firefox, follow the instructions for finding your profile without having to open Firefox.

    In the menu bar, click Firefox and select Quit Firefox

    Locate the prefs.js file (and, if applicable, the prefs.js.moztmp file).
    Delete these files and files prefs - n.js where n is a number (e.g. prefs - 2.js).
    If there is, remove the Invalidprefs.js.
    Restart Firefox. You should now have reset all preferences.

    Based on information from preferences not saved (mozillaZine KB)

    See also http://kb.mozillazine.org/Profile_folder_-_Firefox

    #1: there are too many pref for all kinds of adjustment which will offer a recipe of what you lose and how to keep certain parameters.
    It is possible to copy specific lines of a prefs.js to this file in another profile or restore some settings after deleting this file in the current profile folder.

    All the prefs that show as a user defined and appear in bold on the topic: config page are stored in the prefs.js file.

    This includes the changes you make and data Firefox itself and extensions store as data/parameters in a pref.
    It's

    #2,3: the localstore.rdf file stores the toolbar configuration and other data.

    #4: the current versions of Firefox shows the menu entry "Tabs" at the top menu ' display > toolbars "and" Firefox > Options ' and in the menus toolbar pop-up if the tabs are not in the default position on the top.

    If the notches located on the top and the menu entry is not available and you want to move the tabs under the navigation toolbar, then you have to toggle the pref browser.tabs.onTop false on the subject: config page.

    A restart of Firefox is necessary for updating the menu entry to display or remove.

    Note that this pref will no longer effect when the code Australis lands on the output channel (code Australis will probably land in Firefox 29).

    #5: see https://support.mozilla.org/kb/Clear+Recent+History

    Compensation of the "Site Preferences" clears all exceptions for cookies, images, pop-ups, installing the software, stored passwords in permissions.sqlite and other site specific data stored in content - prefs.sqlite (including zoom on the page).

    Deletion of cookies will delete all specified (selected) cookies, including cookies with an exception allowing you want to keep.

    #6,7: history of search bar is the story of the search bar (Google) on the Navigation toolbar.

    All recorded data to a form on a web page is included in the data in the form, but you can not separate and distinguish the two.

    Browsing history is the history of the web pages you have visited.

    #8: session cookies are always kept in memory and never stored on the disc in cookies.sqlite

    You can only delete specific cookies manually in the Cookie Manager or leave cookies expire when you close Firefox to make them behave like session cookies.

    Cookies of other compensation will include all cookies and don't obey the exceptions that you have made.

    #9
    Data stored in storage DOM is not stored in cookies.sqlite, but it is generally stored in the webappsstore.sqlite file or possibly in the form of data in IndexedDB.

  • Yahoo email won't load and store settings in the OS x mail application

    I tried to mail yahoo mail OSX El Capitan. Using the Yahoo tab in the box menu for the establishment of new accounts I can get the drop-down list to enter my email address that is recognized by Yahoo saying welcome + the address just entered. I press next to enter my password it is accepted. seconds after the drop falls again ask for the e-mail address and the password again. This time, I get the loading wheel which runs forever. After going to the doctor of connection I find mail forgot all my e-mail address and yahoo settings. It doesn't let me manually as some of the input fields are eliminated. My web yahoo mail warns me that my iMac has connected twice to my yahoo account. I went back into the box selection of accounts once again, before other suppliers named and pressed (other) then I found a button with a blue representative logo email that I have lived the same as before proceeder. Guess what? It loaded perfectly! The only problem is that this article only gives me the apps. Mail and Notes.Nothing else is available. If the Yahoo logo button had loaded, I would also have other Contacts apps.like & calendars + two other institutions. How can I get the missing apps to work using the mail icon settings?

    Is this your first attempt using Yahoo! mail on Mac? I had some weird problems with my own Yahoo! account today, and I know that sometimes he just goes a bit wonky and correct itself on its own. Unfortunately, it's a big part of the reason I do not use my Yahoo! account more.

    Have you tried to manually configure the account as an IMAP account? Y at - it none of the settings of your Yahoo! account to restrict connections and others? You have two-step verification enabled for your account?

  • Equium L20-198: error 0271 check date and time settings.

    My apologies if this appears twice, I tried to change and I somehow lost my thread.

    Hi people.

    For awhile, I had problems with my laptop. Toshiba Equium L20-198.

    If I unplug the network at any time, when I re - connect and start the computer, I get two warnings.

    Date and time settings error 0271 check.

    WARNING 0251 system cmos checksum bad default configuration used

    About 6 months ago we replaced the CMOS battery, while we struggled to find a brand new ML1220EI2 Nickel hydrogen 3V 14mAh, we had to go for a "used" quality one.

    The problem persists and I now also get this message every time that I reboot rather put into hibernation.

    Yes, the computer is a little more than 5 years and hit a little, but it is absolutely perfect in all other ways - with one exception - the main battery is completely dead. If the network becomes disconnected, I make you stop in about 3 minutes. :(

    Is it possible that the CMOS battery charge the main battery and this is my problem? I did a little research on Google and found a similar question and an answer on a Dell forum where someone has stated that the CMOS takes his food on the main battery. Would this be the case with my Equium and could buy a new battery solve my problem? I obvioiusly don't want to spend £30 + for it will not help, any response would be appreciated.

    Thank you.

    > Is it possible that the CMOS battery charge the main battery and this is my problem?
    Well, the CMOS battery can be charged with AC adapter but the laptop must be turned on for about 18 to 20 hours.
    It s not I known if battery CMOS takes the power of the main battery
    Usually the CMOS battery should always charge in work and when the laptop is plugged in
    So, theoretically the main battery has no influence on the CMOS battery.

    I think it might be a mobo problem, I think this could be a reason for it

    By the way; in most cases the CMOS battery is not removable... so I wonder how did you repalce this CMOS battery...

  • L20-198 error 0271 check date and time settings

    Hi people.

    For awhile, I had problems with my laptop. Toshiba Equium L20-198.

    If I unplug the network at any time, when I re - connect and start the computer, I get two warnings.

    Date and time settings error 0271 check.

    WARNING 0251 system cmos checksum bad default configuration used

    About 6 months ago we replaced the CMOS battery, while we struggled to find a brand new ML1220EI2 Nickel hydrogen 3V 14mAh, we had to go for a "used" quality one.

    The problem persists and I now also get this message every time that I reboot rather put into hibernation.

    Yes, the computer is a little more than 5 years and hit a little, but it is absolutely perfect in all other ways - with one exception - the main battery is completely dead. If the network becomes disconnected, I make you stop in about 3 minutes. :(

    Is it possible that the CMOS battery charge the main battery and this is my problem? I did a little research on Google and found a similar question and an answer on a Dell forum where someone has stated that the CMOS takes his food on the main battery. Would this be the case with my Equium and could buy a new battery solve my problem? I obvioiusly don't want to spend £30 + for it will not help, any response would be appreciated.

    Thank you.

    Post edited by: d14ner

    Hi people.

    For awhile, I had problems with my laptop. Toshiba Equium L20-198.

    If I unplug the network at any time, when I re - connect and start the computer, I get two warnings.

    Date and time settings error 0271 check.

    WARNING 0251 system cmos checksum bad default configuration used

    About 6 months ago we replaced the CMOS battery, while we struggled to find a brand new ML1220EI2 Nickel hydrogen 3V 14mAh, we had to go for a "used" quality one.

    The problem persists and I now also get this message every time that I reboot rather put into hibernation.

    Yes, the computer is a little more than 5 years and hit a little, but it is absolutely perfect in all other ways - with one exception - the main battery is completely dead. If the network becomes disconnected, I make you stop in about 3 minutes. :(

    Is it possible that the CMOS battery charge the main battery and this is my problem? I did a little research on Google and found a similar question and an answer on a Dell forum where someone has stated that the CMOS takes his food on the main battery. Would this be the case with my Equium and could buy a new battery solve my problem? I obvioiusly don't want to spend £30 + for it will not help, any response would be appreciated.

    Thank you.

    Post edited by: d14ner

  • Toshiba 40TL938G - find the date and time settings

    I have a 40TL938G and I can't find the date and time settings.
    Can someone help me?

    SSY
    I read the manual and it does ' t say anything about these settings.

    THX

    In the settings of digital television, you should see the option called local time settings

    To display the time on the TV you press the sign of the small clock on the remote control while watching a normal TV show (analog only)

  • Ethernet and Ethernet settings under network settings?

    Noticed that Gray was Ethernet and Ethernet settings under network settings and wireless.

    I was wondering not if that was supposed to be used for something else.

    It is used if you are using a lapdock or dock HD that you can connect a USB Dongle for ethernet and option.

    Mark

    Support Forums Manager

  • File ran and transfer settings Wizard Installation all users in Administrator account info

    I did a Windows XP Pro 32-bit clean install on a laptop.  After I installed all the software and drivers on the machine, I ran the file and Assistant to bring users account on the machine to transfer the parameters.  The problem is that I stumbled accidentally while still connected as long as administrator, all the information of users installing to the default Administrator account.  Y at - it an easy way to remove the users from the administrator account info, or to delete the administrator account take it back to the installed version of basic?  Thanks in advance for your help.

    Original title: using files and Settings Transfer Wizard. Oops

    Hello

    I suspect that Naman R misinterpreted your post. My interpretation is that you have used the Wizard Windows XP file / transfer settings, no Windows Easy Transfer.

    Assuming you still have available transfer fluid, which is a kind of external drive (USB, probably), there is no reason why you should transfer the settings again, but in the correct user profile.

    With respect to the transfer in the account manager, all the parameters of implementation of changes should be reversible system restore (start - all programs-Accessories-System Tools System Restore). Data can only be deleted while signed in as an administrator. Do the system restore before doing the right files and transfer settings, otherwise it will also cancel these changes in settings that have been applied to the appropriate user profiles.

    Tricky

  • Record header and footer settings

    Can someone tell me please how to set the parameters of the header and footer and save these settings for printing so that I don't have to enter the settings area and make sure that my printer is always selected to 'print borders', which is what seems to make the header and footer still print on my page.

    Also, how utiilize the setting "custom" under headers and footers.  I want to divide the date and time on the page and I don't know if I can do it.  That's where I'm wondering if the 'custom' area comes into play.

    I have e-all-in-one-HP Officejet Pro 8600 printing.

    Thanks for any help!

    From what it seems that you have created multiple threads on the same subject. While this may get you an answer in a faster way, it deprives the other users to communicate with us. If in the future, you would create a single thread by number, it will be greatly appreciated.

    As I explained in this post: http://h30434.www3.hp.com/t5/Printing-Issues-Troubleshooting/How-to-set-the-Header-and-Footer-Settings/m-p/2366241

    These parameters are not defined by software or the printer drivers and belong instead of the program that you use (in the case of the thread as I responded to Firefox).

    I hope that you have the information you were looking for and have a nice day!

  • My date and time settings are set in Egypt and whenever updates of the laptop with microsoft server time, it increases of 1 h.

    My date and time settings are set in Egypt and whenever updates of the laptop with microsoft server time, it increases of 1 h.
    Recently in Egypt, changes of daylight has been cancelled and I guess that's the cause of the problem!
    Any ideas?

    If time was recently cancelled, you can go to your control panel:
    Panel-> data and time-zone (tab) >
    and uncheck the "automatically adjust clock for daylight saving time.

    Otherwise, you probably need to adjust your zone settings on your computer using Microsoft time zone Editor.

    TZEdit: <> http://download.microsoft.com/download/5/8/a/58a208b7-7dc7-4bc7-8357-28e29cdac52f/tzedit.exe >

    HTH,
    JW

  • My computer won't recognize bluetooth headset! Error message 'Discoverablilty and connectivity settings were not saved' and 'Bluetooth Exchange folder is not found' by changing the properties of bluetooth

    Original title: my computer won't recognize bluetooth headset!

    When I checked "Allow bluetooth devices to find this computer" under the "Option" menu, I got the error message "Discoverablilty and connectivity settings were not saved. Another message error I got is "Bluetooth Exchange folder is not found".  Although I copied this file from my backup data files, the problem still exists.

    I used to use able to connect to my computer with the headset.

    Please advise me what I have to do.

    Hi Venturer016,

    Remember to make changes to the computer before this problem?

     

    Method 1: You can follow the steps mentioned in the link below

    The problems with Bluetooth devices

    http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-problems-with-Bluetooth-enabled-devices

    Thanks and greetings

    Ajay K

    Microsoft Answers Support Engineer
    ---------------------------------------------------------------------------------------------------------
    Visit our Microsoft answers feedback Forum and let us know what you think.

  • Vista firewall and network settings

    Greetings,

    Running Vista Ultimate OS and for the McAfee Security Center security system, providing the Dell system.  Security Center is a brand product (McAfee) Dell.  It includes a firewall.  It is generally not recommended to run two firewalls at the same time on the same system.  In this case, my preference is to disable the Windows Vista firewall and manage only the McAfee Security Center Firewall.

    However, by doing so, effects of undesirable changes in the Windows Vista network configuration.  Specifically, disable the Vista Firewall automatically turns on the discovery network and file sharing in the network settings of Vista, which is not desired.

    The question:

    What is the solution to run Windows Vista with the firewall (Vista) integrated offshore, the McAfee Security Center Firewall and discovery network and settings (network) off the coast of file sharing?

    By the way, my troubleshooting on this has included disable McAfee Firewall to determine if she could be causing a conflict with the firewall and Windows network settings.  Apparently not, because even with McAfee firewall off it is still not possible to disable the Windows Firewall (in this case, No firewall is running) without network discovery and sharing settings being switched automatically on files.

    Again, the goal is to run the McAfee Firewall with the network discovery and parameters (network) off the coast of file sharing and Windows Vista firewall off the coast.

    Thank you-

    Network discovery is enabled or disabled in vista network and sharing Center by activating or deactivating vista firewall rules. You can maybe re-create these rules in the McAfee Firewall, although they will be not be enabled / disabled from the network sharing Center. The following site will show how to display vista firewall rules:
    http://NPR.Freei.me
    Are you sure there is no setting in McAfee to block the sharing of files and network discovery?

    Note: the rules for sharing printers and files, and network discovery are clearly identified in the vista firewall.

  • Windows makes the automatic update and my settings are only for download.

    Windows 7 - I've always had my updates the setting that allows them to download, but I chose to install them.  These past few weeks I've noticed that if I refuse and install these updates that they automatically install themselves.  I like to choose how to upgrade usually one at a time, so if there is a problem I know what update caused it.  But in recent weeks a notice that he has downloaded the updates look bad.  So when a few days where I don't bother updating automatically they settle.  I checked my setting of many times, and my settings are correct.  So why are my rules being ignored?

    Once the updates are downloaded, all that is left restarts to install updates

    Some updates that don't require not a reboot will probably install

    Hardly a way to install an update at the same time as you want too.

    I suggest you these parameters personally if install one at a time is your preference

    These settings will be updated also exclude recommended to be mixed in the important section, recommended updates cause most of the problems.

Maybe you are looking for