SPA9000 And direct Ip calls?

Similar Questions

• Courses and non-traversal calls

  Hello

  Can someone explain in simple terms what are courses and non-traversal calls?, what is the difference? And also the VCS control below must traversal licenses?

  CTI-VCS-CONTRL-K9

  Control of VCS

  Thanks in advance.

  If you have two endpoint C-series (i.e. CTS-SX20) both recorded on VCS control and also capable of reaching out directly between them (a routing), then in general the call will address as non-traversal call Endpoint, so no license courses will be necessary.

  However if these Endpoint calling each other, but using different protocol (i.e. an end point registered in VCS control only with H323 and other endpoint registered on the CV with SIP), or different IP version (that is to say one with IPv6 and other with IPv4 registration), then control VCS remain media routing in order to manage such scenario of interoperability which will require licensed traversal appeal.

• Port of native queue, the AA and the voice call

  Hi all

  Recently, I met a challenge problem, the customer got a busy tone when they called the number of hunting. We have AA 9 connection of the unit-based, we also have the queue of the native call (Hunt). When the client calls the DID number that we published, the number called will be translated to 100 on H.323 voice gateway, and then click CUCM and directly forward to voicemail (primarily to computer virtual in DN 100). Then the call will be forwarded to CUCM hunting through the connection of the unit to call manager after time control.

  Call routing as follows.

  Dial the number DID of PSTN--> voice gateway (translate PSTN number to 100)--> CUCM--> connection of the unit (call handler)--> native CUCM call queue

  We have a PRI dedicated to hunting, there are a large number of channels available when the question that's happened. In order to avoid congestion caused by the voice port. I added Subscriber connection of the unit so that the cluster CUC for 48-Port voice. Whenever I have reset the port in UC Group, the problem disappeared. Sometimes, there are only 3-5 calls for hunting, but the question is yet. I was wondering is there something wrong with the voice port settings?

  Thanks in advance,

  Eric

  I see, holiday would be difficult, but you can set the static days in the periods of time in CUCM, which is technically the same as in UCXN.

  I guess I see your description of what your question is exactly, are calls arriving is no longer the hunt group of?

• Mail envelopes blackBerry Smartphones at the reception in direct connect calls

  Hello all, new to the forum!  Frustrated and look for the answerman! My carrier replaced my Blackberry 8350i with another assuming that was the problem.

  Well, when I get directly connect calls and do not answer them immediately and receive other calls Direct Connect, the message envelope accumulates 1 for one, whenever I get a new Direct Connect. But after completing the message counter does not and continues to accumulate Direct Connect calls and only Direct Connect calls. Emails, sms and others disappear or subtracted from the total after reading them. When I "clean up" the call directory is empty but the message envelope counter does not reset.

  1. message counter accumulates ONLY when direct connect through Sprint calls received

  2. I have not found a method to eliminate memory except by removing the battery

  3 deletion of call logs does not solve the problem

  4. the old Blackberry and other has the problem

  5. the latest version of the software loaded

  This can be corrected? It seems to me like a software problem? I have the latest updates of software loaded with no improvement.

  sqamicheal wrote:

  • This function cannot be executed ALT, CAP and DEL.
    

  huh? Did you follow the instructions as indicated... Shift to the RIGHT, which is the key to the CAP?

• Why apple card app does not show the routes and directions between two places in India in an iphone 6 s more?

  map does not show the routes and directions

  This feature is not yet supported in India.

  http://www.Apple.com/in/iOS/feature-availability/#maps-directions

  In addition, your phone may be overheating for a number of reasons. The most common of which is low service area.

  Your attributes from battery to the majority of the production of heat, then adjust settings to put less load on the farm in general will help some.

  http://www.Apple.com/batteries/maximizing-performance/#iOS

• How can I put merge Toolkit and direct mail (for office) on a MacBook OS?

  How can I put merge Toolkit and direct mail (for office) on a MacBook OS?

  They don't seem to offer a Mac version. See https://www.mapilab.com/support/faq/system_requirements_outlook.html

  You can use the following to contact them to check that: https://www.mapilab.com/about/contact.html

• I have a persistent popup on my iphone screen saying I have ad/spyware and need to call support technique apple to 1-800-893-4975. Was suspicious so nicknamed by land line. No response. Can't warning screen to stop jumping whenever I have access to the in

  I was on facebook and clicked on a link to a recipe (went there before). I had a start to screen popping up saying repeatedly I had ad/spyware and necessary to call 1-800-893-4975 (supposedly to support technique apple) to find out how to remove it. I was suspicious so I used my landline to call the number. There was no reply or a message. It is also on the screen: www.issue.safari.net.

  I don't know if it is a type of scam. My support of apple technology has expired and cannot find any phone #/ email I can use to communicate with them. I also can't find anything online. I can't get the screen to stop appearing when I go on the internet on my phone.  Can anyone help? I'm not all tech savvy.

  It's a scam. Do not call the number.

  Double click on the Home button, and then drag upward on the preview of Safari.

  Go to settings - Safari - clear history.

  Restart Safari.

• I'm doing a Shell call Firefox in the directory C:\Program Files (x 86) of \Mozilla FireFox\ and LabView shell call gives an error.

  I'm doing a Shell call Firefox in the directory C:\Program Files (x 86) of \Mozilla FireFox\ and LabView shell call gives an error. I can go to the BACK shell and make the fine call, but Labview Shell gives several errors. Anyone know how to get around the problem of directory with the name of the Program Files (x 86) directory with space and the (x 86) BACK doesn't seem to like?

  You must use quotation marks.

• I want to control the speed and direction of a motor continuous using labview with pwm

  I want to control the speed and direction of a motor (essentially a toy motor) continuous generating a PWM signal in labview. I'm using L293d motor and exit DAQ-9472. Can I do this without the help of any microcontroller but only a simple labview code and the DAQ 9472 output

  There are many examples on how to generate a PWM on one in the buffer, or on a counter, but that does not support this card.  A 8 a cDAQ chassis also a BNC connector that can be used as a counter as well.  These examples can be found in help > example Finder in LabVIEW.

  Also be aware of your current limiting.  This card can drive a decent amount of current, but it has its limits.  You'll want to put an inline meter to see what is current and see how far you get to it.

• I have just started with a new internet provider and get phone calls from a source to say that they are windows and the need to access my computer because its infected in windows. It is this true.

  I have just started with a new internet provider and get phone calls from a source to say that they are windows and the need to access my computer because its infected in windows. It is this true.

  No, it's a scam, ignore the call.

  Just hang up, they are trying to steal your information or to install a virus on your PC.

• Unable to play games because DirectDraw and Direct 3D acceleration: not available

  I have a laptop HP DV9930us delivered with windows vista 64.  I upgraded to Windows 7 Home Premium 64-bit and installed DirectX 11.  I can't run any games or programs that use 3D graphics and when I run DxDiag, it said that the DirectDraw and Direct 3D acceleration options are not available.  Everything I read said to enable them, but there is no option to enable them.  Before the upgrade to Windows 7, everything works great.  Any help is appreciated.  Thanks in advance.

  Hello

  1. what operating system do you use?

  2. what game do you play?

  I suggest you follow the link and check.

  Diagnosing basic problems with DirectX

  http://Windows.Microsoft.com/en-us/Windows7/diagnosing-basic-problems-with-DirectX

• NFC and direct Wifi does not

  I haver tried nfs and direct wifi on my z3.

  But today decided to try the brothers samsung galaxy s4.

  The problems:

  I can send files using nfc to s4 but s4 is not able to send anything for me via nfs. Quite strange!

  If force us again and again, only google game store opens automatically.

  We enabled wifi direct on our phones and it showed connected as well.

  But whenever we try to share whatever it is, it says "failed to send ' after a while on the S4.

  And on my phone it doesn't do anything even though it shows always connected in Wifi settings live.

  I tried using Commander file, select file, send via wifi direct, the s4 as connected watch and when I click it it that nothing happens at all!

  So, what's the use of direct Wifi on Z3?

  In this case seems to be the S4, I was able to transfer files between Z and Z1 Z1 with a Z3, I had hit and Miss with Xperias and samsung, but not with the Xperias and other androids.

• I've updated the Mac driver for the 8600 and direct wireless printing is no longer works. V5.9.1

  I've updated the Mac driver for the 8600 and direct wireless printing is no longer works. The HP utility is v5.9.1, Mac OS x 10.7. I did the software update and a new driver HP was part of the package. HP ePrint still works, and print tests are okay for General network settings are intact. None of the applications that use the print dialogue box standard and local networking make it through the print queue. Any tips? Any way to roll back a driver version? Or quickly get the next revision and hope printing works again? Thank you.

  Update: OSX-specific Version is 10.7.5, model of the printer is HP OfficeJet 8600. See you soon.

  Hello

  Try to reboot the router and check if that can help you.

  After connecting the back of the router, wait 30-60 seconds and restart the printer and Mac.

  If it persists, try resettign the system as follows:

  * Be aware that reset the printer system will eliminate any existing queue and reset all custom settings driver.

  Click on the Apple menu and then click on System Preferences.
  Select Print & Scan.
  Right click (or Ctrl + click) your product with the Printers list in the left panel and then click on reset printing system.
  Click OK to confirm the reset.
  Type your user name and password.
  Click OK. The printing system resets.

  Now reconfigure the device by following the HP (under Utilities Applications\hewlett-Packard\Device) installation wizard.

  Please let me know if this can help,

  Shlomi

• Error: [810215] MakeDecision method is disabled and cannot be called.

  Hello!

  Odd error here: I am trying to call a method named "MakeDecision" in the Web Designer PersonWantsOrg cutomizer. For a few hours, I get the message "error: [810215] MakeDecision method is disabled and cannot be called. '. I can't explain it to myself, because this call works very well for a long time... anyone have an idea why this message is triggered? Or where I can see the status (?) of the method? Or, which changes the status?

  .. .and Yes, I compiled everything... several times... honestly

  Thank you very much

  Norbert

  Hi Norbert,.

  suggestion:

  Use the method "FillOrder.

  With this you are able to create a new PersonWantsOrg object and can set each property (including the OrderState).

  You must set a PropertyBag object (which contains all the properties for the new object of PersonWantsOrg), you create a new (empty) PersonWantsOrg object and call this method. The PropertyBag object is needed as a parameter to the method.

  Disadvantage: The method works only for execution by a Jobservice.

  That's why I suggest:

  Your "One-button-click" fires an event for the object selected in the PersonWantsOrg.

  You must create a process for this event, this process contains a ScriptExec job. This work calls a script with the following behavior:

  -a single parameter (UID_PWO_Source)

  -load the source object

  -fill in all the important properties of this object in a PropertyBag object, add additional properties (for example OrderState = Assigned)

  -create a new PersonWantsOrg object

  -call the method "FillOrder" for this new object and use the PropertyBag object

  The result is a new PersonWantsOrg object that is finally approved.

  I hope it helps.

  Kind regards

  Steffen

• Cisco Jabber CDR analysis and reporting: the lost packets and other info call stating "Null."

  Hello

  I have recently setup Cisco Jabber Setup and make a video call between Mac and Windows laptop. When I go to the CDR reporting, I can find my call details when I search after the end of the call. However, I see lost packets, jitter, latency as Null.

  I looked in the support forums and made all the required configurations such as going to service settings and allowing the call diagnosis. I also uncheck CDR load only one box, but not seeing any information other than the ip address and the details of the bandwidth of VideoCAP.

  Am I missing something?

  CDR.png

  

  No, the CMR is not implemented in any current version of Jabber, the next version of Jabber will be the first to have * some * RMC capacity.

  What you see at the present time, is the expected behavior.