SSL VPN traffic
Hello
I have configured the client SSL VPN on SAA. I'm able to establish SSL VPN with the ASA and obtaining the IP address of subnet defined (CorporateVPN 172.16.0.100 - 172.16.0.110). But when I try to ping inside the property intellectual treats which is 172.16.0.1 and other machine in the range LAN getting loss of packets to the remote machine.
What could be the problem?
Below is the configuration of the SAA.
ASA Version 7.2 (1)
!
Cisco - ASA host name
test.com domain name
activate the password password
names of
DNS-guard
!
interface Ethernet0/0
Description connected to ISP
nameif outside
security-level 0
IP address "public IP".
!
interface Ethernet0/1
Shutdown
No nameif
no level of security
no ip address
!
interface Ethernet0/2
Description connected to the local network
nameif inside
security-level 100
172.16.0.1 IP address 255.255.255.0
!
interface Ethernet0/3
Shutdown
No nameif
no level of security
no ip address
!
interface Management0/0
nameif management
security-level 0
IP 192.168.1.1 255.255.255.0
management only
!
2KFQnbNIdI.2KYOU encrypted passwd
boot system Disk0: / asa721 - k8.bin
passive FTP mode
clock timezone GMT 3 30
management of the DNS domain-lookup service
DNS server-group DefaultDNS
Server name 203.123.165.75
test.com domain name
pager lines 24
Enable logging
asdm of logging of information
Outside 1500 MTU
Within 1500 MTU
management of MTU 1500
mask 172.16.0.100 - 172.16.0.110 255.255.255.0 IP local pool CorporateVPN
IP verify reverse path to the outside interface
IP verify reverse path inside interface
no failover
ASDM image disk0: / asdm521.bin
don't allow no asdm history
ARP timeout 14400
Global 1 interface (outside)
NAT (inside) 1 172.16.0.0 255.255.255.0
Route outside 0.0.0.0 0.0.0.0 Gateway 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout, uauth 0:05:00 absolute
internal GroupPolicy1 group strategy
attributes of Group Policy GroupPolicy1
Protocol-tunnel-VPN IPSec l2tp ipsec webvpn
WebVPN
enable SVC
SVC Dungeon-Installer installed
time to generate a new key of SVC 30
SVC generate a new method ssl key
internal Netadmin group strategy
Group Policy attributes Netadmin
Protocol-tunnel-VPN IPSec l2tp ipsec webvpn
WebVPN
Required SVC
SVC Dungeon-Installer installed
time to generate a new key of SVC 30
generate a new key SVC new-tunnel method
dpd-interval SVC 500 customer
dpd-interval SVC 500 gateway
username cisco password encrypted privilege 15 ffIRPGpDSOJh9YLq
attributes username cisco
VPN-group-policy Netadmin
http server enable 444
http 192.168.1.0 255.255.255.0 management
http 0.0.0.0 0.0.0.0 outdoors
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
attributes global-tunnel-group DefaultWEBVPNGroup
address pool CorporateVPN
tunnel-group NetForceGroup type webvpn
attributes global-tunnel-group NetForceGroup
address (inside) CorporateVPN pool
address pool CorporateVPN
Group Policy - by default-Netadmin
No vpn-addr-assign aaa
No dhcp vpn-addr-assign
Telnet 192.168.1.0 255.255.255.0 management
Telnet timeout 10
SSH timeout 5
Console timeout 0
management of 192.168.1.2 - dhcpd address 192.168.1.254
enable dhcpd management
!
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns migrated_dns_map_1
parameters
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the migrated_dns_map_1 dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
!
global service-policy global_policy
WebVPN
allow outside
SVC disk0:/crypto_archive/sslclient-win-1.1.1.164 2 image
enable SVC
context of prompt hostname
Cryptochecksum:13f5616c7345efb239d7996741ffa7b3
: end
Yes, 'inside access management' is only to manage/ping of the SAA within the interface. Without this command, they would still be able to access the internal network. This command is only used to manage the SAA within the interface itself.
Tags: Cisco Security
Similar Questions
-
RVL200 - SSL VPN and firewall rules
Forgive my ignorance, but I have been immersed in the configuration of this device RVL200 to allow Remoting SSL VPN to a customer site, sight unseen. I have the basics of the VPN set up in config, but now move the firewall rules. We want to block all internal devices to access the Internet, but I don't want to cripple the remote clients that will be borrowed by blocking their return via the SSL VPN traffic. This leads to my questions:
(1) a rule of DENIAL of coverage for all traffic OUTBOUND will prevent the primary function of the VPN (to allow the administration away from machines on the local network)?
(2) if the answer to #1 is 'Yes', what ports/services do I need to open the side LAN?
(3) building # 2, configuring authorized outbound rules apply only for VPN clients, rather than all the hosts on LAN?
(4) as the default INCOMING traffic rule is to REFUSE EVERYTHING, do I have to create a rule to allow the VPN tunnel, or guess that in the configuration of the router?
Here are some other details:
- The LAN behind the RVL200 is also isolated LAN in a manufacturing environment
- All hosts on this network have a static IP address on a single subnet.
- The RVL200 has been configured with a static, public IP on the WAN/INTERNET side.
- DHCP has been disabled on the RVL200
- Authentication to the device will use a local database.
- There is no such thing as no DNS server on the local network
- The device upstream of the RVL200 is a modem using PPPoE DSL, and the device has been configured for this setting.
- Several database of local users accounts were created to facilitate the SSL VPN access.
I worked with other aspects of it for a long time, but limited experience with VPN and the associated firewall rules and zero with this family of aircraft. Any help will be greatly appreciated.
aponikikay, there is no port forwarding necessary to the function of the RVL200 SSL - VPN.
Topic 1. That is not proven. It shouldn't do. The router should automatically make sure that the SSL - VPN router service is functional and accessible.
Re 2. No transfer necessary. In addition, never before TCP/UDP port 47 or 50 for VPN functions. The TCP 1723 port is used for PPTP. UDP 500 is used for ISAKMP. You usually also to transmit TCP/UDP 4500 port for IPSec encapsulation.
Let's not port 47. ERM is an IP protocol that is used for virtual private networks. It is a TCP or UDP protocol. GRE has 47 IP protocol number. It has nothing to do with TCP or UDP port 47. TCP and UDP are completely different protocols of free WILL.
It goes the same for 50: ESP is the payload for IPSec tunnels. ESP is the Protocol IP 50. It has nothing to do with TCP or UDP port 50.
'Transfer' of the GRE is configured with PPTP passthrough option.
'Transfer' of the ESP is configured with IPSec passthrough option.
-
Order SSL VPN with Cisco Cloud Web Security
We have implemented Cisco Cloud Web Security with the connector of the ASA and transfer all traffic port 80 and 443 to the Tower of the CCW. We have enabled HTTPS inspection, and I was wondering if there was anything, we can add in the configuration that would allow us to control (allow/block) SSL VPN?
#Clientless SSL VPN is not supported with Cloud Security Web; don't forget to exempt all SSL VPN traffic without client service ASA for Cloud Web Security Strategy.
Reference: http://www.cisco.com/c/en/us/td/docs/security/asa/asa90/configuration/gu...
-
Dear score
I configured SSL VPN on c3845. WebVPN working via browser but through webvpn client I am able to connect but can not reach an internal with ip address on the network. Please find the show for your reference
Check your 'ip nat inside' list 1 and make sure that you're not VPN traffic to be NATted
-heather
-
Hello
We have had problems with the SSL VPN for quite awhile, but don't seem to be getting anywhere.
This is an intermittent problem that we can not simply track down.
Users can connect to the VPN, get an IP address and show as connected on GEORGE page.
Users concerned, always shows a time of 0: logon. If they try to access anything whatsoever, they cannot, as looks that all traffic is blocked.
I ran a trace of packets to an affected user, and it shows this. To me, it looks like a firewall policy blocks.(* Parcel number: 1 * header values: bytes captured: 74, real bytes on the wire: 74 Packet Info(Time:02/19/2016 18:01:42.256): in: X 1 * (interface), out:-, DROPPED, Code Drop: 582 Id of Module (package abandoned-denied by SSLVPN under user control strategy),: 27 (policy), (Ref.Id: _968_qpmjdzDifdl), 18:31) ether header Ethernet Type: IP (0 x 800), Src = [00:11:22:33:44:55], Dst = [c2 [:ea:e4:b1:8 b: 23] Type of IP header IP Packet: ICMP (0 x 1), Src = [192.118.201.6], [172.18.1.252] = Type ICMP ICMP Packet Header Dst = 8 (ECHO_REQUEST), ICMP Code = 0, 19407 value = ICMP checksum: [2] dump hexadecimal and ASCII of the package: c2eae4b1 8 b 230011 22334455 and 08004500 003c1a76 00008001 *... #... "3DU... E...<.v....* e8bfc076="" c906ac12="" 01fc0800="" 4bcf0001="" 018c6162="" 63646566="" *...v........k.....abcdef*="" 6768696a="" 6b6c6d6e="" 6f707172="" 73747576="" 77616263="" 64656667="" *ghijklmnopqrstuvwabcdefg*="" 6869="" *hi="">
The only solution is to unplug / reconnect several times, until he started working. We cannot find a reason for this. Somedays it works very good and other days it is not.
Any help would be greatly appreciated.
Thank you
Hello
Just came across the same problem.
We had some additional IP address ranges that had to go through the firewall on SSLVPN. I beilive source was the same.
When configuring users > local users must also assign in selected authorized user access VPN (pencil icon on the right of the user name) Configure > VPN access.
Once I created the Group of subnet for all subnets internal and permitted all Local defined users to access this group for VPN access settings, all traffic began to flow.
I see that 1/2 of last year, but I just joined.
Kind regards
Rajko
-
I wonder if it is possible to have 2 SSL VPN client running simultaneously at the same time. When I'm working out of the site, I have to do the following:
1. I call Array SSL VPN network to connect to the corporate network. I need it to be able to read emails.
2. I invoke some other developed internal SSL VPN client to connect to the customer's network. This is necessary to get access to access the Citrix customer environment.
When I run the 2nd SSL VPN, my vision behaves erratically as the gel or the loss of connection to the exchange server.
SSL VPN network table is a SSL VPN split, which means that it routes web traffic of the company and nothing else.
Developed internal SSL VPN is configured to route specific IP range.
I wonder if there is any limitation in Windows 7 32 - bit OS that prevent me to simultaneously run 2 SSL VPN clients.
Appreciate your comments and your support.
Hi SamPersis,
Your question of Windows is more complex than what is generally answered in the Microsoft Answers forums. Appropriate in the TechNet forums.
Please post your question in the Windows 7 IT Pro TechNet Forums: http://social.technet.microsoft.com/Forums/windows/en-US/home?category=w7itpro
Thank you.
-
ACL rule does not work after the SSL VPN connection
Hello
I have the following configuration:
-VLAN LAN (192.168.5.0/24)
-VLAN WLAN (192.168.20.0/24)
-SSL VPN VLAN (192.168.200.0/24)
Default policy denies access to the local network. If the value rule ACL to allow traffic between WLAN and LAN. Works very well.
Now I connect with AnyConnect and access resources on the network VLAN. Works.
After you have disconnected the VPN I can't access the LAN to WLAN VLAN. If I disable the ACL rule and turn it back on, it works again until someone connects with SSL VPN.
I use firmware 1.2.15. Any ideas when this bug fixed?
Kind regards
Simon
HI Simon,.
This bug will be fixed in 1.2.16.
I don't know the exact date for the release.
But it should be out soon. If you need the fix sooner,
Please open a case of pension.
Kind regards
Wei
-
Of SSL VPN is not able to access from the outside
Configuration SSL VPN, unable to access from outside, when trying to access the browser site, it says "cannot display the Page.
Area basic firewall is configured, there must be something that I'm missing, please see the attached config.
Any help please
Looks like you will have to allow SSL VPN from the WAN traffic to the free zone (ZP-WAN-to-self), so you need to update the political map (PMAP-JM-WAN) in particular the ACL (ACL-VPN-PROTOCOL), must allow access to port 443 of any source IP address:
permit tcp any
.. .should do the trick. Cheers, Seb.eq 443 -
Should what license I for 25 SSL VPN peers
Hi all
I want to implement cluster active / standby with a pair of ASAs 5550 and I have a licensing question. Here's the "sh - key retail activation" leave two output devices...
ASA1:
SH - activation in detail key:
Serial number: XXXXX
No temporary key assets.
Activation key running: XXXXX XXXXX XXXXX XXXXX XXXXX
The devices allowed for this platform:
The maximum physical Interfaces: unlimited
VLAN maximum: 250
Internal hosts: unlimited
Failover: Active/active
VPN - A: enabled
VPN-3DES-AES: enabled
Security contexts: 2
GTP/GPRS: disabled
SSL VPN peers: 2
Total of the VPN peers: 5000
Sharing license: disabled
AnyConnect for Mobile: disabled
AnyConnect Cisco VPN phone: disabled
AnyConnect Essentials: disabled
Assessment of Advanced endpoint: disabled
Proxy sessions for the UC phone: 2
Total number of Sessions of Proxy UC: 2
Botnet traffic filter: disabled
This platform includes an ASA 5550 VPN Premium license.
Flash activation key is the SAME as the key running.
ASA2:
SH - activation in detail key:
Serial number: XXXXX
No temporary key assets.
Activation key running: XXXXX XXXXX XXXXX XXXXX XXXXX
The devices allowed for this platform:
The maximum physical Interfaces: unlimited
VLAN maximum: 250
Internal hosts: unlimited
Failover: Active/active
VPN - A: enabled
VPN-3DES-AES: enabled
Security contexts: 2
GTP/GPRS: disabled
VPN SSL counterparts: 25
Total of the VPN peers: 5000
Sharing license: disabled
AnyConnect for Mobile: disabled
AnyConnect Cisco VPN phone: disabled
AnyConnect Essentials: disabled
Assessment of Advanced endpoint: disabled
Proxy sessions for the UC phone: 2
Total number of Sessions of Proxy UC: 2
Botnet traffic filter: disabled
This platform includes an ASA 5550 VPN Premium license.
Flash activation key is the SAME as the key running.
--------------------------------------------------------------
It seems so obvious that I have to upgrade the first ASA to support 25 SSL VPN peers in order to create the cluster HA, right?
Now, I want to know do I need the license "ASA5505-SSL25-K9" or something else.
Thank you very much in advance for any help!
Ah OK I see - right then: upgading pole will allow the license to share.
Re the version target, I would recommend going directly to 8.4 (4.1). I have it deployed on several sites without problem.
-
access of entrepreneurs and employees of the web site in-house using clientless ssl vpn.
We have a layout of web SSL VPN without customer who allow employees and suppliers of connection and internal display web page. I wonder if possible separate employees and contractors to access internal pages. The internal web page has no authentication of users. They would like to see if it is possible that traffic employees get proxy behind interface INSIDE IP de ASA and entrepreneur behind a different IP address proxy traffic. Thus, the internal web page can check IP to contractor and only give them access to view certain web page, but not all pages.
Hello
Creating a group policy for each user group will be a good option, you can also use DAP to assign an ACL web to the user who logs on the portal without client, you can use the Radius, LDAP or Cisco attributes to associate the DAP for the user. For example, if you are using LDAP, you can create 2 groups separated here for employees and entrepreneurs and based on the LDAP user group membership, they will be assigned to specific web acl configured according to their access restrictions.
You can follow this link to set up an acl of web:
http://www.Cisco.com/c/en/us/TD/docs/security/ASA/asa83/asdm63/Configura...
Once the ACL is ready, you can follow this guide to configure the DAP Protocol: "check the web for acls figure10.
http://www.Cisco.com/c/en/us/support/docs/security/ASA-5500-x-series-NEX...
Thank you, please note!
-
Hello
I want to configure SSL VPN on my Cisco ASA 5510 for more information, then 30 users will have to access simultaneously, but I don't know if my license that allow.
Below is the features of my ASA license:
The devices allowed for this platform:
The maximum physical Interfaces: unlimited
VLAN maximum: 50
Internal hosts: unlimited
Failover: disabled
VPN - A: enabled
VPN-3DES-AES: enabled
Security contexts: 0
GTP/GPRS: disabled
SSL VPN peers: 2
The VPN peers total: 250
Sharing license: disabled
AnyConnect for Mobile: disabled
AnyConnect for Linksys phone: disabled
AnyConnect Essentials: disabled
Assessment of Advanced endpoint: disabled
Proxy sessions for the UC phone: 2
Total number of Sessions of Proxy UC: 2
Botnet traffic filter: disabledThis platform includes a basic license.
Concerning
Walid
You ASA have a license for this. You need to order AnyConnect MORE if you want to use the AnyConnect Client or you have licenses AnyConnect APEX order if you want to use the VPN without client.
The two are not allowed on the simultaneous connections. You must count users who use them. MOR info is in the Guide of command AnyConnect.
-
IP NAT on the router on SSL - VPN appliance
Someone at - it allows to transmit 443/SSL on a SSL VPN Cisco 891 - K9 unit?
(I have never encountered this situation before as the router VPN terminated public face directly or we had several IPs public to assign the VPN device directly a public IP address).
With ' ip nat inside source static tcp 44.55.66.255 443 10.10.10.150 443 extensible "is supposed to pass the SSL request to the appliance SSL VPN to 10.10.10.150 to have VPN applications ended here.
But failed miserably body 891 - K9 created a virtual ARP entry for 10.10.10.150. So two MACs with the same IP address.
So 443 requests were sent to its interface. At the hearing of NAT, I can't ssh inside SSL - VPN, but by the time the statemet disappeared, I can ssh and warning dupliacte ARP goes.
* 1 Nov 19:22:46.871: % IP-4-DUPADDR: duplicate address 10.10.10.150 on Vlan10, a source of aaaa.bbbb.cccc
* 1 Nov 19:23:18.083: % IP-4-DUPADDR: duplicate address 10.10.10.150 on Vlan10, a source of aaaa.bbbb.cccc
* 1 Nov 19:23:48.295: % IP-4-DUPADDR: duplicate address 10.10.10.150 on Vlan10, a source of aaaa.bbbb.cccc
RTR #sh clock
* 19:24:26.487 UTC Sunday, November 1, 2015
RTR #sh ip arp 10.10.10.150
Protocol of age (min) address Addr Type Interface equipment
Internet 10.10.10.150 - e02f.6d96.8dd0 ARPA Vlan10
RTR #sh ip arp 10.10.10.150
Protocol of age (min) address Addr Type Interface equipment
Internet 10.10.10.150 - e02f.6d96.8dd0 ARPA Vlan10
RTR #sh sh ip route 10.10.10.150Cisco TAC to reproduce this problem at the moment to report dev.
Does anyone else have this problem or a workaround?
Thank you.
I may be misunderstanding but isn't your NAT statement backwards IE. If you want traffic to pass to 10.10.10.150 it shouldn't be-
' ip nat inside source static tcp 10.10.10.150 43 43 44.55.66.25x.
isn't the device for SSL connection on interface 'ip nat inside '?
Jon
-
I have a couple of site to site VPN working properly on an ASA 5515. Don't know what is on the other side, as I haven't seen them. I configured a SSL vpn for remote users who must be able to access resources on remote sites. I got access to the network of site without any problems and and have added the range of IP addresses for remote users to links from site to site, but I am unable to connect. Anyone who has this performance, it would be greatly appreciated if you can help.
Hi mbluemel,
You need to configure the remote side to allow traffic from the remote side for SSL VPN users.
This list of documents the measures taken to achieve this: -.http://www.petenetlive.com/kb/article/0000040.htm
For more information: -.
http://www.Cisco.com/c/en/us/support/docs/security/ASA-5500-x-series-NEX...Kind regards
Dinesh MoudgilPS Please rate helpful messages.
-
Cannot access internal network so AnyConnect SSL VPN, ASA 9.1 (6)
Hello Cisco community support,
I have a lab which consists of two virtual environments connected to a 3750-G switch that is connected to a 2901 router which is connected to an ASA 5512 - X which is connected to my ISP gateway. I configured SSL VPN using AnyConnect and can establish a VPN to the ASA from the outside but once connected, I can't access internal network resources or access the internet. My information network and ASA configuration is listed below. Thank you for any assistance you can offer.
ISP network gateway: 10.1.10.0/24
ASA to the router network: 10.1.40.0/30
Pool DHCP VPN: 10.1.30.0/24
Network of the range: 10.1.20.0/24
Development network: 10.1.10.0/24
: Saved
:
: Serial number: FCH18477CPT
: Material: ASA5512, 4096 MB RAM, CPU Clarkdale 2793 MHz, 1 CPU (2 cores)
:
ASA 6,0000 Version 1
!
hostname ctcndasa01
activate bcn1WtX5vuf3YzS3 encrypted password
names of
cnd-vpn-dhcp-pool 10.1.30.1 mask - 255.255.255.0 IP local pool 10.1.30.200
!
interface GigabitEthernet0/0
nameif inside
security-level 100
IP 10.1.40.1 255.255.255.252
!
interface GigabitEthernet0/1
nameif outside
security-level 0
address IP X.X.X.237 255.255.255.248
!
interface GigabitEthernet0/2
Shutdown
No nameif
no level of security
no ip address
!
interface GigabitEthernet0/3
Shutdown
No nameif
no level of security
no ip address
!
interface GigabitEthernet0/4
Shutdown
No nameif
no level of security
no ip address
!
interface GigabitEthernet0/5
Shutdown
No nameif
no level of security
no ip address
!
interface Management0/0
management only
nameif management
security-level 100
IP 192.168.1.1 255.255.255.0
!
boot system Disk0: / asa916-1-smp - k8.bin
boot system Disk0: / asa912-smp - k8.bin
passive FTP mode
permit same-security-traffic intra-interface
network of the NETWORK_OBJ_10.1.30.0_24 object
10.1.30.0 subnet 255.255.255.0
network obj_any object
network obj_10.1.40.0 object
10.1.40.0 subnet 255.255.255.0
network obj_10.1.30.0 object
10.1.30.0 subnet 255.255.255.0
outside_access_in list extended access permitted ip object NETWORK_OBJ_10.1.30.0_24 all
FREE access-list extended ip 10.1.40.0 NAT allow 255.255.255.0 10.1.30.0 255.255.255.0
access-list 101 extended allow any4 any4-answer icmp echo
access-list standard split allow 10.1.40.0 255.255.255.0
pager lines 24
Enable logging
asdm of logging of information
Within 1500 MTU
Outside 1500 MTU
management of MTU 1500
ICMP unreachable rate-limit 1 burst-size 1
ICMP allow any inside
ICMP allow all outside
ASDM image disk0: / asdm - 743.bin
don't allow no asdm history
ARP timeout 14400
no permit-nonconnected arp
NAT (inside, outside) source obj_10.1.40.0 destination obj_10.1.40.0 static static obj_10.1.30.0 obj_10.1.30.0 non-proxy-arp-search to itinerary
NAT (inside, outside) static source any any static destination NETWORK_OBJ_10.1.30.0_24 NETWORK_OBJ_10.1.30.0_24 non-proxy-arp-search to itinerary
Access-group outside_access_in in interface outside
!
Router eigrp 1
Network 10.1.10.0 255.255.255.0
Network 10.1.20.0 255.255.255.0
Network 10.1.30.0 255.255.255.0
Network 10.1.40.0 255.255.255.252
!
Route outside 0.0.0.0 0.0.0.0 10.1.10.1 1
Timeout xlate 03:00
Pat-xlate timeout 0:00:30
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
without activating the user identity
identity of the user by default-domain LOCAL
Enable http server
http 192.168.1.0 255.255.255.0 management
http 192.168.1.0 255.255.255.0 inside
http X.X.X.238 255.255.255.255 outside
No snmp server location
No snmp Server contact
Crypto ipsec pmtu aging infinite - the security association
Crypto ca trustpoint ASDM_Launcher_Access_TrustPoint_0
registration auto
full domain name no
name of the object CN = 10.1.30.254, CN = ctcndasa01
ASDM_LAUNCHER key pair
Configure CRL
trustpool crypto ca policy
string encryption ca ASDM_Launcher_Access_TrustPoint_0 certificates
certificate c902a155
308201cd 30820136 a0030201 020204c 0d06092a 864886f7 0d 010105 9 02a 15530
0500302b 31133011 06035504 03130 has 63 61736130 31311430 12060355 74636e64
0403130 31302e31 2e33302e 32353430 1e170d31 35303731 32303530 3133315a b
170d 3235 30373039 30353031 33315 has 30 2 b 311330 0403130a 11060355 6374636e
64617361 30313114 30120603 55040313 0b31302e 312e3330 2e323534 30819f30
0d06092a 864886f7 010101 05000381 8 d 0d 003081 89028181 00a47cfc 6b5f8b9e
9b106ad6 857ec34c 01028f71 d35fb7b5 6a61ea33 569fefca 3791657f eeee91f2
705ab2ea 09207c4f dfbbc18a 749b19ae d3ca8aa7 3370510b a5a96fd4 f9e06332
4355 db1a4b88 475f96a1 318f7031 40668a4d afa44384 819d fa164c05 2e586ccc
3ea59b78 5976f685 2abbdcf6 f3b448e5 30aa96a8 1ed4e178 0001300 020301 4 d d
06092a 86 01010505 00038181 0093656f 639e138e 90b69e66 b50190fc 4886f70d
42d9b4a8 11828da4 e0765d9c 52d84f8b 8e70747e e760de88 c43dc5eb 1808bd0f
fd2230c1 53f68ea1 00f3e956 97eb313e 26cc49d7 25b927b5 43d8d3fa f212fcaf
59eb8104 98e3a1d9 e05d3bcb 428cd7c6 61b530f5 fe193d15 ef8c7f08 37ad16f5
d8966b50 917a88bb f4f30d82 6f8b58ba 61
quit smoking
Telnet timeout 5
SSH stricthostkeycheck
SSH timeout 5
SSH group dh-Group1-sha1 key exchange
Console timeout 0
VPN-addr-assign local reuse / 360 time
management of 192.168.1.2 - dhcpd address 192.168.1.254
enable dhcpd management
!
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
Trust ASDM_Launcher_Access_TrustPoint_0 vpnlb-ip SSL-point
SSL-trust outside ASDM_Launcher_Access_TrustPoint_0 point
WebVPN
allow outside
AnyConnect image disk0:/anyconnect-linux-3.1.09013-k9.pkg 4
AnyConnect image disk0:/anyconnect-macosx-i386-3.1.09013-k9.pkg 5
AnyConnect image disk0:/anyconnect-win-3.1.09013-k9.pkg 6
AnyConnect enable
tunnel-group-list activate
internal GroupPolicy_cnd-vpn group policy
GroupPolicy_cnd-vpn group policy attributes
WINS server no
value of server DNS 8.8.8.8
client ssl-VPN-tunnel-Protocol
by default no
xxxx GCOh1bma8K1tKZHa username encrypted password
type tunnel-group cnd - vpn remote access
tunnel-group global cnd-vpn-attributes
address-cnd-vpn-dhcp-pool
strategy-group-by default GroupPolicy_cnd-vpn
tunnel-group cnd - vpn webvpn-attributes
activation of the alias group cnd - vpn
!
ICMP-class class-map
match default-inspection-traffic
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map icmp_policy
icmp category
inspect the icmp
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
Review the ip options
inspect the icmp
!
global service-policy global_policy
service-policy icmp_policy outside interface
context of prompt hostname
no remote anonymous reporting call
Cryptochecksum:261228832f3b57983bcc2b4ed5a8a9d0
: end
ASDM image disk0: / asdm - 743.bin
don't allow no asdm historyCan you confirm that this is correct, your diagram shows your IP address public on ASA as 30 while you have assinged on 'outside' interface like 29?
-
WebVPN and remote vpn, ssl vpn anyconnect
Hi all
Differences between webvpn and remote vpn, ssl vpn anyconnect
All require a separate license?Thank you
Hello
The difference between the webvpn and SSL VPN Client is the WebVPN to use SSL/TLS and port
send through a java application to support the application, it also only supports TCP for unicast traffic, no ip address
address is assigned to the customer, and the navigation on the web in the tunnel is made with a SSL
Web-mangle that allows us stuff things in theSSL session.
SSL VPN (Anyconnect) Client is a client of complete tunneling using SSL/TCP, which installs an application on the computer and
envelopes vpn traffic in the ssl session and thus also an assigned ip address has the
tunnel's two-way, not one-way. It allows for the support of the application on the
tunnel without having to configure a port forward for each application.
AnyConnect is a client of new generation, which has replaced the old vpn client and can be used as long as the IPSEC vpn ssl.
For anyconnect licenses please see the link below:
http://www.Cisco.com/c/en/us/TD/docs/security/vpn_client/AnyConnect/ANYC...
Kind regards
Kanwal
Maybe you are looking for
-
Satellite M40x-250 - CD/DVD drive works sporadically
My laptop CD/DVD driver has always worked properly but in recent months, that it is no more. Most of the time that an error message telling me the CD or DVD cannot be read. Sometimes it does not work properly, and sometimes it doesn't work but very s
-
Satellite L500-1GE - cannot use hotkeys
Hello everyone!I'm Tibor of Hungary. I'm not a big forum user, but now I need a little help. I have a Satellite L500-1GE and I use Windows 7 ultimate (64 bit). My problem is the following:I can't use shortcut keys (FN + F1... 9 buttons) and so I can
-
Using ComponentOne c1chart with Labview
Someone of experience using the C1Chart (or a 3-d chart) of ComponentOne with LabView? Background: we have a c# dll that contains a control to the user with a C1Chart placed on it and a lot of wrapper code to make the C1Chart data color of LAB plot.
-
How can I recover the Vista operating system?
I have a tablet that is using Windows Vista. Hard to drive tablets erased clean with Vista. How can I recover the Vista operating system? I hope that I don't need to go out and buy a new OS, because the Tablet is worth only a few dollars and can be l
-
Just got a call from people claiming to be Microsoft saying that my computer is spreading a virus using Microsoft servers and that, at least that I followed their instructions Microsoft would turn off my computer in 3-4 h, I guess it's a hoax?