STOP: 0X0000009F

Similar Questions

• Stop 0x0000009f (0 x 00000003, 0 x 89168030...

  Start Windows Vista Home Premium on my computer and after about 5 minutes, it freezes.  After another 10 minutes approximately, it goes to a blue screen and displays "Stop 0x0000009f (0 x 00000003, 0 x 89168030...» ». These are all the numbers that I could write down.  My computer works fine in safe mode, but I can't find a solution to this problem. Once I was able to run a diagnosis with System Mechanic and he said a hard drive error that he was unable to fix.  Any suggestions?

  most likely a software conflict. Try to perform a clean boot:

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7
  http://support.Microsoft.com/kb/929135/en-us

  I hope I could help

• Windows 7 blue screen: DRIVER_POWER_STATE_FAILURE STOP: 0x0000009f (0 x 00000003,... ntkrnlpa.exe)

  Hi all

  I got a blue screen today with my Windows 7 which is something disappointing and I don't want to do it again, can someone check the dump for me file and tell me what is the cause?

  ********************************************************************************
  The problem seems to be caused by the following file: ntkrnlpa.exe

  DRIVER_POWER_STATE_FAILURE

  Technical information:

  STOP: 0X0000009F (0 X 00000003, 0X8903B458, 0X83133AE0, 0X88B16008)

  Ntkrnlpa.exe - address 0x830eaf1c base at 0x8300c000 DateStamp 0x4f5583be

  ********************************************************************************

  I have:

  Intel i5 760
  4 GB of ram
  Windows 7 32 bit
  Comodo 5.10.228257.2253
  NOD32 4.2.71.2

  In case there is something wireless (I read something on this, but not sure!), I have:

  Device USB of TP-link wireless (& TP-link utility)
  SecurityKISS tunnel software
  proXPN vpn software

  Drivers:
  Microsoft virtual Wifi Miniport adaprot
  Realtek PCIe GBE controller (disabled)
  TP - LINK 150Mbps Wireless N adapter Lite
  Unknown device
  TP - LINK 150Mbps Wireless N adapter Lite

  VirtualBox has been running a win XP version that has Avast & Comodo

  At the point of issue, virtualbox was operating in full screen, Firefox open and no one to the PC (no action)

  I downloaded the dump file to:
  http://DepositFiles.com/files/q4ebw15vb
  Password: win7win

  Thank you

  Hello

  You have made any changes to your computer recently?

  I suggest you to follow the steps and check if it helps.

  Method 1: Disconnect all external devices except your mouse and your keyboard and check what is happening.

  Method 2:

  Step 1: Login to the Safe Mode and then check if it helps.

  Start your computer in safe mode

  Step 2: Perform a clean boot Hardware and a software clean boot, and then check if it helps.

  (a) click "Start" and type "DEVMGMT. MSC"in the search text box and press enter

  (b) develop "audio, video and game controllers".

  (c) right click on your sound card, select "Properties".

  (d) 'Pilot' click, click Disable the selected device. Click OK

  (e) Please use the same method to disable other devices such as: Modem, network card, CD - R drive. Please note that some devices such as the video card are not available should be disabled.

  (f) Please restart the computer.

  Note: do not forget to activate the devices to return after you complete your troubleshooting.

  Method 3: You can also check out the link and then check if it helps.

  Resolve stop (blue screen) error in Windows 7

• Windows 7 STOP: 0x0000009F (0 X 89637028, 0 X 000000003, 0X8316CAE0, 0XAA3AEE28).

  Crashes Windows 7 troubleshooting problem, opportunity, power, problem still exists. computer crashes. Help, please.

  Thanks in advance. THAIDADDY

  Check out this recent article can be useful

  http://support.Microsoft.com/kb/2315295

• Get a stop error code 0x0000009f

  Original title: need help, reading of files .dmp to determine the cause of the BSOD

  I have recently experienced BSOD with my PC at home and wish assistance tracks down to the root of the problem.

  .Dmp files have been compressed and are available on SkyDrive here-> http://sdrv.ms/XXrpxP
  I am on windows 7 and software configurations have not changed in the last month (possibly there have been automatic updates that have occurred).  Please let me know if other information needed to help determine the cause of the BSOD.

  Thank you

  Ryan Morrison

  Looks like Sunbelt Personal Firewall can cause this stop / 0x0000009f. I would like to uninstall it

  Then see if it crashes

  It seems that AVG is also installed, if there is a firewall, you must have a firewall installed.

  Otherwise they will conflict with each other

• (0 X 00000003 0X0000009F DRIVER_POWER_STATE_FAILURE BSOD,

  Hello!

  Whenever I try to shut down the computer during the night when I am finished working, it doesn't seem to stop. When I stopped him, he just starts to go through the process, but ultimately a BSOD occurs, which forces me to shut down the computer manually by holding the power button.

  Here, I have attached mini-decharges for three consecutive days that had the same BSOD on shutdown, all the files in the links are the same:

  https://rapidshare.com/files/3053652346/minidumps.rar
  http://www.Filefactory.com/file/c18d1c2/n/minidumps.rar
  http://www.mediafire.com/?60phwhgyabsygmf

  My computer model is Toshiba Satellite x 205-sli2 where it is useful.

  I hope that you will be able to help me with this problem. Thank you!

  Hello

  Results verified BlueScreenView WinDBG / DumpCHK.
  
  The Bug_Check were all 9F CAUSE RTKVHDA.sys, which is the function Realtek (r) High Definition Audio driver.

  9F error checking, {3, 8e46d180, 9429cb30, c64c0188}
  Probably caused by: RTKVHDA.sys
  Nom_image: RTKVHDA.sys
  MODULE_NAME: RTKVHDA

  RTKVHDA.sys dated 28/07/2009 Realtek (r) High Definition Audio Driver to function.

  Loaded symbol image file: RTKVHDA.sys
  Image path: \SystemRoot\system32\drivers\RTKVHDA.sys
  Image name: RTKVHDA.sys
  Timestamp: Kills Jul 28 06:02:38 2009 (4A6EF6EE)

  1. update RealTek Audio Codec driver.

  Driver Realtek HD Audio Codec of USA - right side-
  http://www.Realtek.com/default.aspx

  2.check with Toshiba Support, their drivers and documentation online and ask in their forums
  on the problems known. Look for the updates to the BIOS, chipset of low level drivers and major
  embedded device drivers. Also update all drivers - run DriverView - important separate device
  SEE to hide drivers Microsoft - those without drain update in their name.

  TOSHIBA = BiosVendor
  BiosVersion = V2.10
  BiosReleaseDate = 20/12/2007<- check="" for="" updates="" to="" the="" bios,="" low="" level="" chipset="" drivers,="" and="" the="">
  device embedded and separate drivers.
  TOSHIBA = SystemManufacturer
  SystemProductName = Satellite X 205
  Family = ABCDEFGHIJKLMNOPQRSTUVWXYZ
  SystemVersion = PSPBUU-01900J
  SystemSKU = 012345678912345678912345678
  TOSHIBA = BaseBoardManufacturer

  3 use the other methods in the troubleshooters below.

  ====================================
  ====================================

  Check this KB:

  The shutdown process does not terminate and you receive an error message on a computer that is
  running Windows Vista or Windows Server 2008: "Stop 0x0000009F"
  http://support.Microsoft.com/kb/972109

  ----------------

  You use Roxio or Nero programs? They have been known to cause this problem even
  If they worked well for a long period of time. If so check with their support.

  Check this thread for more information on using BlueScreenView, MyEventViewer and other methods of
  Troubleshoot BlueScreens - answers top 3 (+ 1 more).

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_vista-system/blue-screen-plug-and-play-detected-an-error-most/3deab2fa-4000-4136-8c78-a3d22b1db009

  ----------------------------------------------------------

  References to Vista also apply to Windows 7.

  This "might" be a power problem, even if this isn't the most common cause - in this case
  It seems that the PSU could be the fault.

  9F is probably a driver issue. Security/antivirus/antispware programs can also cause these issues.
  Have you added the recent devices or the updated drivers - don't forget to check in the Windows updates to see
  If a driver has been updated before this happen. This can also be caused by a loose card or cable
  and even a weak power supply.

  This error means that a driver does not properly support the power state. Check in Control Panel - device
  Manager to ensure that the drivers are not stop during sleep - double-click adapter - NETWORK adapter
  and WIFI - healthy and others - tab power management - uncheck allow the computer to turn off.
  Maybe the only has a problem.

  Start - type in the search - find MSCONFIG in top - right, click on – RUN AS ADMIN

  General tab - tick this box start Diagnostic - APPLY / OK - REBOOT

  Try it now. If the computer still blue screens thinks that video driver. Otherwise think the card NETWORK, Wifi, sound, or...
  (and it might still be video interacts with something else). See following message for my
  generic driver update methods.

  BCCode: 9F 0x0000009F<-- read="" this="">
  * 1167.html? order = date http://www.faultwire.com/solutions-fatal_error/Driver-Power-State-Failure-0x0000009F-

  ==========================================

  Look in the Event Viewer to see if something is reported on those.
  http://www.computerperformance.co.UK/Vista/vista_event_viewer.htm

  MyEventViewer - free - a simple alternative in the standard Windows Event Viewer.
  TIP - Options - Advanced filter allows you to see a period of time instead of the entire file.
  http://www.NirSoft.NET/utils/my_event_viewer.html

  -------------------------------------------------------------------------

  Here are a few ways to possibly fix the blue screen issue. If you could give the blue screen
  info that would help. Such as ITC and 4 others entered at the bottom left. And all others
  error information such as codes of STOP and info like IRQL_NOT_LESS_OR_EQUAL or PAGE_FAULT_IN_NONPAGED_AREA and similar messages.

  As examples:

  BCCode: 116
  BCP1: 87BC9510
  BCP2: 8C013D80
  BCP3: 00000000
  BCP4: 00000002

  or in this format:

  Stop: 0 x 00000000 (oxoooooooo oxoooooooo oxoooooooo oxooooooooo)
  Tcpip.sys - address blocking 0 x 0 00000000 000000000 DateStamp 0 x 000000000

  It is an excellent tool for displaying the blue screen error information

  BlueScreenView scans all your minidump files created during 'blue screen of death '.
  hangs and displays information about all accidents of a table - free
  http://www.NirSoft.NET/utils/blue_screen_view.html

  BlueScreens many are caused by old or damaged, in particular the video drivers drivers however
  There are other causes.

  You can do without if needed fail or the Vista DVD or recovery command prompt mode
  Options if your system was installed by the manufacturer.

  This tells you how to access the System Recovery Options and/or a Vista DVD
  http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

  You can try a system restore to a point before the problem started when one exists.

  How to make a Vista system restore
  http://www.Vistax64.com/tutorials/76905-System-Restore-how.html

  -------------------------------------------------------------------------

  Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN

  Enter this at the command prompt - sfc/scannow

  How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
  generates in Windows Vista cbs.log
  http://support.Microsoft.com/kb/928228

  The log can give you the answer if there is a corrupted driver. (Says not all possible
  driver problems).

  Also run CheckDisk, so we cannot exclude as much as possible of the corruption.

  How to run the check disk at startup in Vista
  http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

  -------------------------------------------------------------------------

  Often drivers up-to-date will help, usually video, sound, network card (NIC), WiFi, part 3
  keyboard and mouse, as well as of other major device drivers.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  How to install a device driver in Vista Device Manager
  http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.html

  How to disable automatic driver Installation in Windows Vista - drivers
  http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
  http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

  -------------------------------------------------------------------------

  How to fix BlueScreen (STOP) errors that cause Windows Vista to shut down or restart
  quit unexpectedly
  http://support.Microsoft.com/kb/958233

  Troubleshooting, STOP error blue screen Vista
  http://www.chicagotech.NET/Vista/vistabluescreen.htm

  Understanding and decoding BSOD (blue screen of death) Messages
  http://www.Taranfx.com/blog/?p=692

  Windows - troubleshooting blue screen errors
  http://KB.wisc.edu/page.php?id=7033

  -------------------------------------------------------------------------

  In some cases, it may be necessary.

  The Options or Vista recovery disk Startup Repair

  How to do a startup repair
  http://www.Vistax64.com/tutorials/91467-startup-repair.html

  This tells you how to access the System Recovery Options and/or a Vista DVD
  http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">

• KERNEL_DATA_INPAGE_ERROR Stop: 0x0000007A (0xc0403bc8, 0xc000000E, 0xZC895860, 0 x 80779000) Storport.sys - address 80779000 base at 80744000. 49e01ef7 datestamp.

  I had this problem with my computer, running Windows Vista Home Premium 32 bit, for several months now, where it will show the blue screen of death shows the error message above. It will be at random times, it seems to just freeze and sit there for a few minutes and then display the error message. I tried chkdsk, System Restore, defragment the HARD disk, running analysis antivirus/antispyware, security scans, check the registry errors, have all the updates and everything I can think of nothing. I saved some of the previous error messages that he brang upward in the same way if they can help with what either.

  * [date - 16/06/09; 8:00p.m.] KERNAL_DATA_INPAGE_ERROR
  Stop: 0x0000007A (0xC0415BBO, 0x000000E, 0x35AED860, 0x82B76000)
  Storport.sys - address 82B 76000 based B 82, 41000, Datestamp 49e01ef7.

  * [day - 17/06/09] Stop: 0x0000007A (0xC000000E, 0x259268C0, 0xC0438A40, 0x87148EC4)

  * DRIVER_STATE_POWER_FAILURE
  Stop: 0 x 00000095 (0 x 00000003, 0x83AD8B70, 0x8560D2B0, 0 x 84417808)

  * [day - 27/08/09] DRIVER_STATE_POWER_FAILURE
  Stop: 0x0000009F (0 x 00000003, 0x8611E030, 0x8611E030, 0xAS09E5B8)

  Pura9910

  Hello

  If a PC you can try reseating all the memory cards and cables (both ends) - are not just tight - actually remove
  and replace. Remove ALL power before opening the case.

  95 is a Plug n not specified ' error to play and no help.

  9F is usually power associated - powersupply thouugh, there might be question of device or driver and antivirus related.

  7A

  Cause

  Frequently, you can determine the cause of the error status (parameter 2) KERNEL_DATA_INPAGE_ERROR bug check. Some common status codes are:

  • 0xC000009A or STATUS_INSUFFICIENT_RESOURCES, indicates a lack of non-paged pool resources.
  • 0xC000009C or STATUS_DEVICE_DATA_ERROR, generally indicates bad blocks (sectors) on the hard disk.
  • 0xC000009D or STATUS_DEVICE_NOT_CONNECTED, indicates defective or loose wiring, termination or that the controller does not see the hard drive.
  • 0xC000016A or STATUS_DISK_OPERATION_FAILED, indicates bad blocks (sectors) on the hard disk.
  • 0xC0000185 or STATUS_IO_DEVICE_ERROR, indicates improper termination or defective cabling devices SCSI or two trying to use the same IRQ.

  These status codes are common ones that have specific causes. For more information about other possible status codes that can be returned, see the Ntstatus.h file in the operating system Microsoft Windows Driver Kit (WDK).

  Another common cause of this error message is the defective material or failing RAM.

  A virus infection can also cause this bug check.

  Solve the problem

  Solve a problem of bad block: Generally, a status I/O of 0xC000009C or 0xC000016A code indicates that the data can not be read from the disk due to a bad block (sector). If you can restart the computer after the error, Autochk runs automatically and tries to map the bad sector so that it is more used.

  If Autochk does not scan the hard disk for errors, you can manually start the disk scanner. Run Chkdsk /f /r on the system partition. You must restart the computer before the start of the analysis of disk. If you cannot start the computer due to the error, use the Recovery Console and run Chkdsk/r.

  Warning  If your system partition is formatted with the FAT file system the long file names that use the Windows operating system could be damaged if you use Scandisk or another MS-DOS-based disk tool to verify the integrity of your hard disk from MS-DOS. Always use the version of Chkdsk that matches your version of Windows.

  Solve a defective hardware problem: If the State of e / is C0000185 and the paging file is on a SCSI disk, check the cabling and SCSI termination for problems.

  Solve a problem RAM failure: Run the hardware diagnostics feeding by the system manufacturer, especially the memory scanner. For more information about these procedures, see the manual of your computer.

  Check that all the cards in the computer are well calibrated. Use an ink eraser or electrical contact treatment, available in electronic supply stores, to ensure the adapter card contacts are clean.

  Check the system log in Event Viewer for additional error messages that might help identify the device that is causing the error. You can also disable caching memory BIOS to try to resolve this error.

  Make sure that the latest Windows Service Pack is installed.

  If the previous steps do not resolve the error, take the system motherboard to a repair for the diagnostic facility. A crack, a scratched trace, or a defective component on the motherboard can cause this error.

  Solve an infection by the virus: Search your computer for viruses using any update, commercial software that examines the Master Boot Record of the disk hard antivirus. All systems of Windows files can be infected by viruses.

  --------------------------------------------------------------------------

  It's my generic bluescreen convenience store which may help.

  Look in the Event Viewer to see if something is reported on those.
  http://www.computerperformance.co.UK/Vista/vista_event_viewer.htm

  -------------------------------------------------------------------------

  Here are a few ways to possibly fix the blue screen issue. If you could give the info from the blue screen that would be
  Help. Such as ITC and 4 others entered at the bottom left. And any other information such as STOP error
  codes and info like IRQL_NOT_LESS_OR_EQUAL or PAGE_FAULT_IN_NONPAGED_AREA and similar messages.

  As examples:

  BCCode: 116
  BCP1: 87BC9510
  BCP2: 8C013D80
  BCP3: 00000000
  BCP4: 00000002

  or in this format:

  Stop: 0 x 00000000 (oxoooooooo oxoooooooo oxoooooooo oxooooooooo)
  Tcpip.sys - address blocking 0 x 0 00000000 000000000 DateStamp 0 x 000000000

  It is an excellent tool for displaying the blue screen error information

  BlueScreenView scans all your minidump files created during 'blue screen of death' crashes, and displays the
  information on all accidents of a table - free
  http://www.NirSoft.NET/utils/blue_screen_view.html

  BlueScreens many are caused by old or damaged drivers, video drivers in particular, but there are other causes.

  You can follow these steps in the Safe Mode if necessary or the command prompt Vista DVD or Options of recovery if your
  system installed by the manufacturer.

  This tells you how to access the System Recovery Options and/or a Vista DVD
  http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

  You can try a system restore to a point before the problem started when one exists.

  How to make a Vista system restore
  http://www.Vistax64.com/tutorials/76905-System-Restore-how.html

  -------------------------------------------------------------------------

  Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN

  Enter this at the command prompt - sfc/scannow

  How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
  generates in Windows Vista cbs.log
  http://support.Microsoft.com/kb/928228

  The log can give you the answer if there is a corrupted driver. (Says not all possible driver problems).

  Also run CheckDisk, so we cannot exclude as much as possible of the corruption.
  How to run the check disk at startup in Vista
  http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

  -------------------------------------------------------------------------

  Often drivers up-to-date will help, usually video, sound, network card (NIC), WiFi, 3rd party keyboard and
  smile, as well as of other major device drivers.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  How to install a device driver in Vista Device Manager
  http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.html

  How to disable automatic driver Installation in Windows Vista - drivers
  http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
  http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

  -------------------------------------------------------------------------

  How to fix BlueScreen (STOP) errors that cause Windows Vista to shut down or restart unexpectedly
  http://support.Microsoft.com/kb/958233

  Troubleshooting, STOP error blue screen Vista
  http://www.chicagotech.NET/Vista/vistabluescreen.htm

  Understanding and decoding BSOD (blue screen of death) Messages
  http://www.Taranfx.com/blog/?p=692

  Windows - troubleshooting blue screen errors
  http://KB.wisc.edu/page.php?id=7033

  -------------------------------------------------------------------------

  In some cases, it may be necessary.

  The Options or Vista recovery disk Startup Repair

  How to do a startup repair
  http://www.Vistax64.com/tutorials/91467-startup-repair.html

  This tells you how to access the System Recovery Options and/or a Vista DVD
  http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

  I hope this helps.

  Rob - bicycle - Mark Twain said it is good.

• help, BSOD 0x0000009F!

  I saw many items, to try to fix this and it wouldn't work on my laptop.

  I use a Lenove Thinkpad Edge E430c

  I had this BSOD error:
  DRIVER_POWER_STATE_FAILURE
  STOP: 0X0000009F (0 X 00000003, 0X864B9908, 0X833419E0, 0X9A99BC28)

  The last thing I did was update my cd/dvd driver. My laptop cannot read any cd, so what I did is to update its driver automatically using program windows 7 that updates your drivers and it worked! I can read CDs and DVDs now, but that's when the BSOD has started. When I tried to check my cd/dvd driver, she'll tell me that everything is fine.

  the BSOD will appear at random and not when I try to restart or shutdown my laptop.

  I hope someone could help :)

  Send a copy of your dump file in a shared file on your disc of sky with a link here.

  The dump file will be created in c:\windows\minidump. You may need to change your settings in Windows to be able to view the file. To show hidden files type Folder Options in the search box above the Start button and select view advanced settings and check that the box "display files and folders" and 'Hide protected operating system files' are not checked. You may need to scroll down to see the second element. You should also make sure that the box before "Hide extensions of known file types" is not checked.

  What is your computer brand and model? If not a branded computer, what is your motherboard brand and model?

  Please download and run the display driver and download a copy of the report he produced on your sky player. To obtain a report all drivers Select Edition, select all followed by file, save selected items.
  http://www.NirSoft.NET/utils/DriverView.html

  Please provide a copy of your system information file. Type system information in the search box above the Start button and press the ENTER key (alternative is select Start, all programs, accessories, System Tools, system information). Select file, Export and give the file a name noting where it is located. The system creates a new information file system each time system information is available. You must allow a minute or two before the file is completely filled before exporting a copy. Please download your disk from sky to share with everyone and post a link here. Please say if the report was obtained in safe mode. The request for a copy of this file is additional to answer the question about the brand and the model.

  Help with Sky Drive see section 9.3:
  http://www.gerryscomputertips.co.UK/MicrosoftCommunity1.htm

• 0X0000009F DRIVER_POWER_STATE_FAILURE

  Can someone help with this problem?  I'm on Windows 64 bit on a toshiba Qosmio F60 7sp1 lately it's been crashing a lot and if I shut it down it keeps is with this error. see you soon
  DRIVER_POWER_STATE_FAILURE

  STOP: 0X0000009F (0XFFFFFA800BD2BAB0, 0XFFFFF80005CC9518, 0 X 0000000000000003, 0XFFFFFA8012FD5BD0)

  We need the DMP file because it contains the single record of the sequence of events that led to the accident, what drivers have been loaded, and what has been loaded.

  
  

  WE NEED AT LEAST TWO FILES DMP TO SPOT TRENDS AND TO CONFIRM THE DIAGNOSIS.

  You may be able to get the DMP files without crashing by booting in SafeMode (F8) with networking.

  If you are overclocking stop.  (chances are that if you are unsure if you are, you are not)

  To allow us to help you with symptoms BSOD on your computer, download the contents of your folder "\Windows\Minidump".

  The procedure:

  * Copy the contents of \Windows\Minidump to another location (temporary) somewhere on your machine.

  * Zip up the copy (compress)

  * Please download to a service like Skydrive or "Rapidshare" to share files and put a link to them in your answer.

  Link to find out how to download below.

  http://www.WikiHow.com/use-SkyDrive

  To ensure the minidumps are enabled:

  * Click Start, in the search box, type: sysdm.cpl, press ENTER.

  * On the Advanced tab, click Startup and recovery... Settings button.

  * Make sure that automatically restart is unchecked.

  * Under the writing debugging information header, select image partial memory (256 KB) in the list box drop-down (varies from 256kb).

  * Ensure to that small Dump Directory is listed as % systemroot%\Minidump.

  * OK your way out.

  * Reboot if changes have been made.

  Please also run MSinfo32 and download the output as well.

  To run MSinfo32 please go to start > run > MSinfo32

  Go to 'file', 'save' and download the PDF is saved with the DMP

  System specs are extremely useful then please include everything you know.

  
  

  Blue screen view and that crashed are often wrong and should only be used in case of emergency...

  
  

  You can learn more about BSOD here

  You will learn how to test your memory here 

  
  

  
  

  Team Zigzag3143.com  

• 9F Win7 STOP after the rest of the hibernation

  Hello

  I am running Windows 7 Ultimate 64 - bit SP1 on an Intel Core 2 Duo E8400 at stock 3 GHz 6 GB RAM DDR2-800 (5.25 GB usable) and an AMD 7850 2 GB. Gfx card motherboard is ASUS P5K. OS disk is a 120 GB of Corsair SSD Force - GT via the integrated Intel ICH9 SATA Intel controlled v9.1.9.1002 storage controller.

  Usually, I simply SLEEP my camera (hybrid sleep mode) at the end of the day and wake up in the morning for a quick start. Timed hibernation is disabled to save wear and tear on the SSD.

  Today, I decided to Hibernate my machine that I had to turn the power off and didn't want to lose my work space. All right.
  I wake it back up again and walked away while he took over and when I came back I was watching a BSOD STOP 0x0000009F.

  I installed the windows debugging tools and symbols of Win 7 SP1 retail but WinDbg always complain "your debugger does not use appropriate symbols".

  I also downloaded the file minidump here: www.cool-breeze.pwp.blueyonder.co.uk/070513-16146-01.dmp

  Could some kind soul if you please help me understand what caused blue screen please?

  Guidance on how to get the debugger works correctly on my machine will also graciously accepted!

  Hello

  The attached DMP is the bugcheck DRIVER_POWER_STATE_FAILURE (9f).

  This error occurs if the drivers do not manage applications of transition from State power properly, usually during one of the following procedures: stop, suspend or exit from sleep, suspend or resume from hibernation mode.

  It seems to be faulty hcw95bda.sys which is the driver of Tuner Hauppauge MOD7700. See if the updates for it are available here - http://www.hauppauge.com/site/support/support.html

  If not, remove your TV Tuner card temporary for repairs (I assume that's what it's a driver for).

  If we run one! IRP on the IRP address blocked, we get the following:

  Args: 00000000 00000000 00000000 00000000
  [16, 0] 0 fffffa8006082440 0 fffff88006802cc8 00000000-00000000
  \Driver\usbhub hcw95bda
  Args: 00000000 00000000 00000000 00000002
  > [16, 2] 0 1 fffffa8006ddda40 00000000 00000000-00000000 pending
  \Driver\hcw95bda
  Args: 00051100 00000001 00000001 00000002
  [16, 2] 0 e1 fffffa8006df8270 00000000 00000000-00000000 pending
  \Driver\ksthunk

  As you can see, the two drivers listed here:

  1. the only one I listed above.

  2 ksthunk.sys - Kernel Streaming WOW64 Thunk Service. Probably collide with your TV Tuner card driver.

  Things that must also be taken in charge:

  1. your ASACPI.sys (Asus ATK0110 ACPI Utility (a well-known manufacturer of BSOD in Win7 and Win8). Also, a part of the many utilities Asus) is dated 2005. I recommend that either all the utilities Asus update you and or DELETE them.

  2. your RTKVHD64.sys (Realtek High Definition Audio function Driver) is dated 2007. Check the updates here - http://www.realtek.com.tw/downloads/downloadsView.aspx?Langid=1&PNid=8&PFid=14&Level=3&Conn=2

  You can see the site of Asus as well.

  Kind regards

  Patrick

• After sleep ntoskrnl.exe error 0x0000009f DRIVER_POWER_STATE_FAILURE

  DRIVER_POWER_STATE_FAILURE after sleep

  When I put my laptop to sleep by closing the lid or choosing sleep from the beginning, I get a bsod (ntoskrnl.exe 0x0000009f DRIVER_POWER_STATE_FAILURE) when the recovery.
  BlueScreenView report:http://dl.dropbox.com/u/12993257/bsod.htm
  Empty the file: http://dl.dropbox.com/u/12993257/091211-34538-01.zip
  Also, for some reason that I do not get the bsod when it puts itself in standby (IE after expire) but I understand when it hibernate itself.
  Any help is appreciated!
  Phil

  Hi chubble10,

  Method 1
  I suggest you try the steps from the following links:

  Stop error when you upgrade a computer that is running Windows 7 or Windows Server 2008 R2 standby or into hibernation, or when you restart the computer: "0x9F".
  http://support.Microsoft.com/kb/975599

  stop "0x0000009F" error message when a computer enters and fate of putting into hibernation in Windows 7 or Windows Server 2008 R2
  http://support.Microsoft.com/kb/981848

  Method 2
  This issue could be due to corruption of the graphics card driver. I suggest you to update the graphics card drivers.

  Updated a hardware driver that is not working properly
  http://Windows.Microsoft.com/en-in/Windows7/update-a-driver-for-hardware-that-isn ' t-work correctly

• memory dumping 0x0000009f Physics (0 x 00000003, 0x86c7c030, 0x8079ADB0, 0x85B095EB)

  How to solve this problem.

  Hi rayan,

  There seems to be a problem with the physical memory.

  Perform the steps from the link below and see if it helps.

  STOP 0x0000009F error code or code error Stop 0x000000FE on a Windows Vista-based or Windows 7 computer that uses certain USB AMD EHCI host controllers

  Important:  This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs.

  For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:

  322756 (http://support.microsoft.com/kb/322756/( )

  Good day!

• HP Pavilion s5510 windows stop

  Twice in the last week I got error message on blue screen that windows had unexpectedly shut down to avoid damage. Both times I wasn't on the computer when it happened.  He added that to CHECK ANY NEW HARDWARE or SOFTWARE.  THE DRIVER POWER STATE FAILURE.  REVIEW DISABLEING BIOS MEMORY OPTIONS CACHING OR SHADING. STOP 0X0000009F. First time I rebooted just computer that I had not added new software or hardware.  Itried a sytem restore to earlier date, but there was Aproblem with IE file jsdebuggeride.dll that prevented the restoration. I downloaded IE11 & everything was OK until 4 days later when the same thing happens again. Don't know if I should try repair or the original disks starting system recovery. Any ideas out there?

  Thank you

  papa011

  Hi Dokie,

  Sorry for the delay in response but I wanted to see if running test HGST would find & fix all the problems. Run the test as you suggested & found in the car was OK on test fast but found problems on execution of complete test. Permit HGST repair bad sectors & for more than a month, I had no more problems or questions to the center of the action. No stops Windows or disk errors. Thanks a lot for taking the time to help with my problem.

  Dad

• Qosmio G50 will not complete the installation of Windows 7 64 bit

  Hello world!

  I recently wanted to updated my Qosmio G50 - 12f 32-bit from vista to 7 ultimate 64-bit. I did a clean install: formatted the c partition.

  Everything seemed to work fine until the screen "Setup is preparing your computer for first use. At first, I thought it froze just would not go further. Back to zero (in all modes) would get the same effect.
  But to my surprise and pleasure, she managed to pass this point when I desperately wanted to wait long enough for a miracle to happen. But the problems remain. The configuration process is right! REALLY! slow. I could painfully spend the first screens, like enter the name of the computer, activation screen, modes of security, but with a very long wait time between each. And every time he reaches this final screen of security modes that she would suddenly go to a BSOD:

  Driver power state failure
  STOP 0x0000009F (0xFFFFFA800193DD70, 0xFFFFF80000B9C518, 0 x 0000000000000003, 0xFFFFFA80029C8610)

  Please, anyone have any ideas on how to solve this problem?

  Of course, there should be a driver problem, but how do I update all the drivers without operating system running? I've seen such a feature in the repair of the installation DVD section, but it accepts only .inf files.
  And I can t find those anywhere on the toshiba support website. Only the .exe that you run from your operating system that is already running.

  In any case the Qosmio G50 was not as incompatible with 7-64 bit. So I'm a little confused here!

  Please help ^ ^

  Hello

  I want to ask you about the Windows Vista Dvd disc. Is - this original type one or more of the Assembly?

• blue screen while saving files

  using windows7 on hp pavilion p62ll pc with nvidia GeForce 9100 graphics card.  system hangs during backup to disk easy 1td.  Windows advises graphic driver stopped.   in this case each time backup is attempted.   latest driver available.  no other problems with the computer.

  Did you mean

  HP Pavilion p6211f desktop PC

  Try to install this

  http://support.Microsoft.com/default.aspx/KB/976972

  What is the blue screen error code that you got?

  Stop: 0x0000009F