Stop code 0x8E problem.

Similar Questions

• HP Pavilion dv6-7020us: driver error Code 28 problems

  Sorry if this is kind of a long start...

  Read that a cause for Code 28 may be due again installed equipment that poses a problem of incompatibility, so...

  First stop, due to problem of hard drive, adequate to get a hard drive again earlier this year. The new current hard drive is "INTERNAL HARD DRIVES DO SAMSUNG Spinpoint M8 ST 1000 L 1 TB 5400 RPM 8 MB Cache SATA (looks like break after" 1000"and"SATA", that's all I can put in).»

  Got Windows 7 x 64 bit installed.

  Ethernet controller, network controller, peripheral PCI, PCI Simple Communications Controller, SM Bus controller, Bus controller series universal (USB) and x 2 unknown device (one of whom I assume is the fingerprint reader) all fail with the error code 28.

  The problem, however...

  With the help of other computers and the family, I managed to get the downloaded files specifically driver installation for Windows 7 x 64 bit, moved to a USB key, ran the files on my computer (with nonworking pilots / that responded to the questionnaire), they seemed of ran perfectly fine and appeared to install correctly, but none of the enumerated factors do not always work.

  Now currently at a loss to know what to do...

  Properties: Details: Hardware ID: value...

  Ethernet controller

  PCI\VEN_10EC & DEV_8168 & SUBSYS_1818103C & REV_07

  PCI\VEN_10EC & DEV_8168 & SUBSYS_1818103C

  PCI\VEN_10EC & DEV_8168 & CC_020000

  PCI\VEN_10EC & DEV_8168 & CC_0200

  Network controller

  PCI\VEN_1814 & DEV_539A & SUBSYS_1839103C & REV_00

  PCI\VEN_1814 & DEV_539A & SUBSYS_1839103C

  PCI\VEN_1814 & DEV_539A & CC_028000

  PCI\VEN_1814 & DEV_539A & CC_0280

  PCI device

  PCI\VEN_10EC & DEV_5229 & SUBSYS_1818103C & REV_01

  PCI\VEN_10EC & DEV_5229 & SUBSYS_1818103C

  PCI\VEN_10EC & DEV_5229 & CC_FF0000

  PCI\VEN_10EC & DEV_5229 & CC_FFOO

  PCI Simple Communications controller

  PCI\VEN_8086 & DEV_1E3A & SUBSYS_1818103C & REV_04

  PCI\VEN_8086 & DEV_1E3A & SUBSYS_1818103C

  PCI\VEN_8086 & DEV_1E3A & CC_078000

  PCI\VEN_8086 & DEV_1E3A & CC_0780

  SM Bus controller

  PCI\VEN_8086 & DEV_1E22 & SUBSYS_1818103C & REV_04

  PCI\VEN_8086 & DEV_1E22 & SUBSYS_1818103C

  PCI\VEN_8086 & DEV_1E22 & CC_020500

  PCI\VEN_8086 & DEV_1E22 & CC_0C05

  (USB) Universal Serial Bus controller

  PCI\VEN_8086 & DEV_1E31 & SUBSYS_1818103C & REV_04

  PCI\VEN_8086 & DEV_1E31 & BUBSYS_1818103C

  PCI\VEN_8086 & DEV_1E31 & CC_0C0330

  PCI\VEN_8086 & DEV_1E31 & CC_0C03

  Unknown device

  ACPI\HPQ0004

  * HPQ0004

  Unknown device

  USB\VID_138A & PID_0018 & REV_0078

  USB\VID_138A & PID_0018

  . . . In my view, that it is all information. I'm sorry if I'm actually still lacking some information. Thanks in advance for the help! I look forward to the answer.

  Hello:

  Here are links to the drivers you need in the order you posted devices... just at the height of the sp # with those on your USB.

  Ethernet controller:

  This package contains the Realtek driver local area network (LAN) that allows the NIC (NIC) Realtek chip in the notebook models that are running an operating system supported.

  File name: sp56167.exe

  Network controller:

  This package contains the installation package driver for Ralink Wireless LAN to laptop models controllers that are running a supported operating system.

  File name: sp57538.exe

  PCI device:

  This package contains the driver that allows the Realtek card reader in laptop models running a supported operating system. The card reader allows users to read or write to removable storage cards supported, which are typically used in digital cameras, digital music players and cell phones.

  File name: sp56166.exe

  PCI Simple Communications controller:

  This package provides the driver Intel Management Engine Interface (MEI) for the notebook models and operating systems. The Intel Management Engine Interface allows communication between the host operating system and the Intel Management Engine firmware.

  File name: sp56158.exe

  Controller of Bus SM: NOTE: first install this driver and restart.

  This package contains the driver and Intel Chipset Installation Utility for the notebook models and operating systems. This utility allows the operating system to show the correct name for the Intel hardware that is installed in the Microsoft Windows Device Manager.

  File name: sp56156.exe

  Controller of universal serial (USB) Bus:

  This package provides the driver for the Intel USB 3.0 controller host for the notebook models and operating systems. The driver allows USB 3.0 devices.

  File name: sp56164.exe

  ACPI\HPQ0004:

  This package provides the HP ProtectSmart Hard Drive Protection software (HP 3D Driveguard) for the laptop models running a supported operating system. HP (HP 3D Driveguard) ProtectSmart hard drive Protection software protects the hard drive of "parking the heads ' if the laptop fell accidentally, or is suddenly hit by another object.

  File name: sp61037.exe

  USB\VID_138A & PID_0018:

  This package contains the driver that allows the validity fingerprint sensor in the notebook models that are running a supported operating system. The fingerprint sensor analyzes fingerprints for use with biometric security applications.

  File name: sp56403.exe

• Stop code 0x0000007E installation Win XP

  I do a Windows XP installation on the new hard drive in HP Netbook.  When installing happen to point to windows that open, it stops and I get the 0x0000007E error message.  I restart and stop at the same place.  What is the problem?

  Hi Dilbert,

  Welcome to the community Microsoft and thanks for posting the question.

  According to the description, you cannot install Windows XP, you get stop code 0x0000007E.

  I suggest you refer to the article to resolve the problem of the installation:

  How to solve an error "Stop 0x0000007E (SYSTEM_THREAD_EXCEPTION_NOT_HANDLED) code error" in Windows XP

  http://support.Microsoft.com/kb/330182

  Warning of the BIOS:

  BIOS change / semiconductor (CMOS) to complementary metal oxide settings can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the configuration of the BIOS/CMOS settings can be solved. Changes to settings are at your own risk.

  Please follow these recommended steps and post if you still experience the problem. I will be happy to provide you with additional options.

• Stop Code 0X0000008E (0XC0000005, 0X822711A7,...)

  Hello

  I tried to use this stupid program called Ccleaner and when he went to clean the registry, in my view, that he fucked it with my drivers or something because now my flipping laptop mouse does not work.  in any case, I tried to go back to before that I started the program, but it does not work.

  I get the blue screen of death when I start my computer, and then it just hangs.  The stop codes are the following;

  0X0000008E (0XC0000005, 0X822711A7, 0X8CAE891C, 0x00000000)

  Now, I've done some reading on the first 2 codes, but I can't find anything on the rest.

  I reinstalled Windows Service Pack 2 and that did nothing.  I tried to do a restore and that doesn't work anymore.

  Help, please.

  Thank you

  Chris

  Hello

  Update your driver, BIOS and any software of control and then work through the troubleshooting services
  above if necessary.

  Could be a nuisance pilot. Update your drivers manually looking at system manufacturer and
  Sites of the manufacturer of the device.

  This is my generic how updates of appropriate driver:

  This utility, it is easy see which versions are loaded:

  -Free - DriverView utility displays the list of all device drivers currently loaded on your system.
  For each driver in the list, additional useful information is displayed: load address of the driver,
  Description, version, product name, company that created the driver and more.
  http://www.NirSoft.NET/utils/DriverView.html

  For drivers, visit manufacturer of emergency system and of the manufacturer of the device that are the most common.
  Control Panel - device - Graphics Manager - note the brand and complete model
  your video card - double - tab of the driver - write version information. Now, click on update
  Driver (this can do nothing as MS is far behind the certification of drivers) - then right-click.
  Uninstall - REBOOT it will refresh the driver stack.

  Repeat this for network - card (NIC), Wifi network, sound, mouse, and keyboard if 3rd party
  with their own software and drivers and all other main drivers that you have.

  Now in the system manufacturer (Dell, HP, Toshiba as examples) site (in a restaurant), peripheral
  Site of the manufacturer (Realtek, Intel, Nvidia, ATI, for example) and get their latest versions. (Look for
  BIOS, Chipset and software updates on the site of the manufacturer of the system here.)

  Download - SAVE - go to where you put them - right click - RUN AD ADMIN - REBOOT after
  each installation.

  Always check in the Device Manager - drivers tab to be sure the version you actually install
  presents itself. This is because some restore drivers before the most recent is installed (sound card drivers
  in particular that) so to install a driver - reboot - check that it is installed and repeat as
  necessary.

  Repeat to the manufacturers - BTW in the DO NOT RUN THEIR SCANNER device - check
  manually by model.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  How to install a device driver in Vista Device Manager
  http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.html

  If you update the drivers manually, then it's a good idea to disable the facilities of driver under Windows
  Updates, this leaves ONE of Windows updates, but it will not install the drivers who will be generally
  be older and cause problems. If updates offers a new driver and then HIDE it (right click on it) and
  Then, get new ones manually if you wish.

  How to disable automatic driver Installation in Windows Vista - drivers
  http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
  http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

  I hope this helps and happy holidays!

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">

• Stop code 0x0000c1f5 HELP

  We had to reformat our computer and we had reinstalled everything everything went well past that we got on the interent fine, but when it came to the updates, we have just let it go, after the update retarted the computer, we've got a stop code 0x0000c1f5, he also says to make sure everything is correctly installed and if the problem continues to disable bios (cache or the shading may need to use) well in that safe mode to use advance option we tried all the safe mode options and it will guard will stop code that we tried to restart with the cd with f2, f12, f8 (safe mode) and blue screen again, I'm stuck on my computer and vista is to blame that we did a diagnostic test it and very thing achieved what I can do. Any help is appreciated. I have more money because of the loss of jobs and cant downlaod anything because of the stop code.  Thank you

  Hello

  I suggest you to see the steps from the following links and check that it works.

  Stop error message when you start a Windows Vista-based computer: "0x0000C1F5".

  http://support.Microsoft.com/kb/946084

  How to get around the Stop error 0x0000C1F5 on a Windows Vista-based computer

  http://support.Microsoft.com/kb/970101

• Blue screen AND Google Redirect Virus? STOP code: 0x000000AD (0x00000001, 0x00000000, 0 x 00000006, 0 x 85879410)

  Original title: blue screen of death AND Google Redirect Virus?
  Hey guys! :)

  So last night, my computer has experienced many problems that seem to just get worse and worse.

  It all started with a Google search I did; I must have clicked a bad link or something, because then my computer kept asking me permission to install some kind of .exe file (I don't remember what it's called, but I knew it was sketchy, so I clicked 'Cancel', but the guest has continued to pop up whenever I tried to close.) Then I closed Firefox and the pop - up's order, but then shortly after, a message came up on my screen saying:

  "A problem has been detected and windows has shut down to prevent damage to your computer.
  INTERNAL_POWER_ERROR
  If this is the first time you've seen this stop error screen, restart your computer. If this screen appears again, follow these steps:
  etc etc.

  STOP code: 0x000000AD (0x00000001, 0x00000000, 0 x 00000006, 0 x 85879410)

  After research I discovered that I had the unfortunate Blue Screen of Death, which now appears whenever I try to restart my computer.

  I did a system restore to a time before that day, a malware scan using Hitman Pro 3.5 that has detected a bunch of malware that I deleted, but the BSOD persists. Later in the night, I was unable to run the .exe files and kept getting an error message "the dependency service or group could start", but fortunately, this question is left today (or at least for the moment...)

  Apart from this question, I also have the Google redirect Virus, which I think is related to my BSOD problem. I had a few weeks ago and managed successfully to remove it with Hitman Pro but now he's back with a vengeance. I did multiple scans with Hitman Pro with no results, I tried to launch the Device Manager looking TDSSserv.sys with no luck and I'm starting to feel like there is no hope :(

  I'm not extremely proficient in computer science so absolutely any help would be greatly appreciated! I'm also running Windows Vista on a HP Pavilion laptop if this is useful information.

  Thanks again! :)

  Hello

  try this program to remove it

  Download update and scan with the free version of malwarebytes anti-malware

  http://www.Malwarebytes.org/MBAM.php

  You should also download and run rkill to stop the process of problem before you download and scan with malwarebytes

  http://www.bleepingcomputer.com/download/anti-virus/rkill

  If it does not remove the problem and or work correctly in normal mode do work above in safe mode with networking

  Windows Vista

  Using the F8 method:

  1. Restart your computer.
  2. When the computer starts, you will see your computer hardware are listed. When you see this information begins to tap theF8 key repeatedly until you are presented with theBoot Options Advanced Windows Vista.
  3. Select the Safe Mode with networking with the arrow keys.
  4. Then press enter on your keyboard to start mode without failure of Vista.
  5. To start Windows, you'll be a typical logon screen. Connect to your computer and Vista goes into safe mode.
  6. Do whatever tasks you need and when you are done, reboot to return to normal mode.

• Stop code 0x0000008E

  I looked far and havnt seen anyone with this stop error message, a few trinkets on whats the cause?

  0x0000008E (0xc0000005, 0x006E6940, 0xB2931B3C, 0x00000000)

  Thanks for your help!

  Hello

  For troubleshooting see BlueScreens using BlueScreenView and MyEventViewer and other methods
  This thread - top 3 responses (+ 1 other).

  http://social.answers.Microsoft.com/forums/en-us/vistarepair/thread/3deab2fa-4000-4136-8c78-a3d22b1db009

  --------------------------------------------------------------------------------------------------------------

  Two main causes of this blue screen video drivers and BIOS - check with the system manufacturer
  Site for graphics (Video) card and BIOS, then on site of the manufacturer of the device for the last video. It may be
  other pilots to check there. In updates of Windows - DISABLE the automatic-pilot plant as those who are older and if Windows Updates suggests a pilot just HIDE (see the method in the next
  message).  Antivirus is another possibility

  See methods of update driver generic in the next message.

  ---------------------------------------------------------------

  BCCode: 8th 0x0000008E is the same as 0x1000008E

  Cause

  Bug KERNEL_MODE_EXCEPTION_NOT_HANDLED control is a very common bug control. To interpret it, you must identify which exception has been generated.

  Common exception codes are:

  • 0xc0000005: STATUS_ACCESS_VIOLATION indicates that a memory access violation has occurred.

  Solve the problem

  If you do not have to debug this problem, you must use certain basic troubleshooting techniques:

  • Make sure you have enough disk space.
  • If a driver is identified in the bug check message, disable the driver or check with the manufacturer for driver updates.
  • Try changing video cards.
  • Check with your hardware vendor for updates to the BIOS.
  • Disable the BIOS memory options such as implementing caching or shading.

  If you plan to debug this problem, you may find it difficult to get a stack trace. Parameter 2 (the address of the exception) should identify the driver or function that caused the problem.

  If you do not know the specific cause of the exception, consider the following:

  • Hardware incompatibility. Ensure that all new equipment installed is listed in the list of the products tested Microsoft Windows market.
  • Service driver or defective peripheral system. A chauffeur service or defective peripheral system could be responsible for this error. The hardware problems, such as BIOS incompatibilities, conflicts of memory and IRQ conflicts can also generate this error.

  If the verification of the message bug list a driver by name, disable or remove that driver. In addition, disable or remove drivers or services that have been recently added. If the error occurs during the startup sequence and the system partition is formatted with the NTFS file system, you may be able to use Safe Mode to rename or to delete the faulty driver. If the driver is used as part of the start-up procedure of the system Safe Mode, you must start the computer by using the Recovery Console to access the file.

  If the problem is associated with Win32k.sys, the source of the error may be a third-party remote control program. If this software is installed, you can remove the system startup service using the recovery and then Console by removing the offending system service file.

  Check the system log in Event Viewer for additional error messages that might help identify the device or driver responsible for control of bug 0x1E. You can disable the cache in memory of the BIOS to try to resolve the error. You must also run the diagnostics of material, especially the scanner memory, which provides the manufacturer of the system. For more information about these procedures, see the manual of your computer.

  The error that generates this message may occur after the first reboot during Windows Setup, or after installation is complete. A possible cause of the error is lack of disk space for installation and the system BIOS incompatibilities. For any problems during the installation of Windows that are associated with lack of disk space, reduce the number of files on the hard disk drive target. Search and delete temporary files that you do not have to have, files hidden Internet, application backup files and files saved.chk, which contain fragments of files on disk scans. You can also use an another hard disk drive with more free space for the installation.

  You can solve the problems of BIOS by upgrading the version of the system BIOS

  BCCode: 8th 0x0000008E is the same as 0x1000008E<-- read="" this="">
  * 1151.html? order = date http://www.faultwire.com/solutions-fatal_error/kernel-mode-exception-not-HANDLED-0x0000008E-

  =============================================

  Look in the Event Viewer to see if something is reported on those.
  http://www.computerperformance.co.UK/Vista/vista_event_viewer.htm

  MyEventViewer - free - a simple alternative in the standard Windows Event Viewer.
  TIP - Options - Advanced filter allows you to see a period of time instead of the entire file.
  http://www.NirSoft.NET/utils/my_event_viewer.html

  -------------------------------------------------------------------------

  Also this, so you can see the probable bluescreens. (If necessary)
  
  Windows Vista restarts automatically if your computer encounters an error that requires him to plant.
  http://www.winvistatips.com/disable-automatic-restart-T84.html

  -------------------------------------------------------------------------

  It comes to my convenience store generic bluescreen:

  Here are a few ways to possibly fix the blue screen issue. If you could give the info to blue screen
  This would help. Such as ITC and 4 others entered at the bottom left. And another error
  information such as the STOP codes and info like IRQL_NOT_LESS_OR_EQUAL or PAGE_FAULT_IN_NONPAGED_AREA and similar messages.

  As examples:

  BCCode: 116
  BCP1: 87BC9510
  BCP2: 8C013D80
  BCP3: 00000000
  BCP4: 00000002

  or in this format:

  Stop: 0 x 00000000 (oxoooooooo oxoooooooo oxoooooooo oxooooooooo)
  Tcpip.sys - address blocking 0 x 0 00000000 000000000 DateStamp 0 x 000000000

  It is an excellent tool for displaying the blue screen error information

  BlueScreenView scans all your minidump files created during 'blue screen of death '.
  hangs and displays information about all accidents of a table - free
  http://www.NirSoft.NET/utils/blue_screen_view.html

  BlueScreens many are caused by old or damaged, in particular the video drivers drivers however
  There are other causes.

  You can do without if needed fail or the Vista DVD or recovery command prompt mode
  Options if your system was installed by the manufacturer.

  This tells you how to access the System Recovery Options and/or a Vista DVD
  http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

  You can try a system restore to a point before the problem started when one exists.

  How to make a Vista system restore
  http://www.Vistax64.com/tutorials/76905-System-Restore-how.html

  -------------------------------------------------------------------------

  Start - type this into the search-> find COMMAND to top box and RIGHT CLICK-
  RUN AS ADMIN

  Enter this at the command prompt - sfc/scannow

  How to analyze the log file entries that the Microsoft Windows Resource Checker
  (SFC.exe) program generates in Windows Vista cbs.log
  http://support.Microsoft.com/kb/928228

  The log can give you the answer if there is a corrupted driver. (Says not all possible
  driver problems).

  Also run CheckDisk, so we cannot exclude as much as possible of the corruption.

  How to run the check disk at startup in Vista
  http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

  -------------------------------------------------------------------------

  Often drivers up-to-date will help, usually video, sound, network card (NIC), WiFi, part 3
  keyboard and mouse, as well as of other major device drivers.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  How to install a device driver in Vista Device Manager
  http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.html

  How to disable automatic driver Installation in Windows Vista - drivers
  http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
  http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

  -------------------------------------------------------------------------

  How to fix BlueScreen (STOP) errors that cause Windows Vista to shut down or restart
  quit unexpectedly
  http://support.Microsoft.com/kb/958233

  Troubleshooting, STOP error blue screen Vista
  http://www.chicagotech.NET/Vista/vistabluescreen.htm

  Understanding and decoding BSOD (blue screen of death) Messages
  http://www.Taranfx.com/blog/?p=692

  Windows - troubleshooting blue screen errors
  http://KB.wisc.edu/page.php?id=7033

  -------------------------------------------------------------------------

  In some cases, it may be necessary.

  The Options or Vista recovery disk Startup Repair

  How to do a startup repair
  http://www.Vistax64.com/tutorials/91467-startup-repair.html

  This tells you how to access the System Recovery Options and/or a Vista DVD
  http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

  I hope this helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• Blue Screen stop Codes, failed to start the laptop at all the

  I have an Inspiron running XP Media Center edition.  Something strange happened last night where the power was interrupted during the closing down and the laptop has become something weird Media Center Genuine Advantage. I don't know what it was, I was half asleep at the time.

  In any case, this morning, I can't start the laptop.  It brings me to a screen where I have the option of waiting for Windows to start, start Windows normally or start in safe mode.  None of these work.  They bring me straight to a blue screen with stop code: 0 x 00000024.  Then, in parentheses, there these: 0 x 00190203, Ox8651F288, 0xC000102, 0 x 000000000.

  I searched a bit, and seems the only solution that I found the recovery utility, but I have a few questions about it.  One, I lose my data? Two, it says it's for advanced users, and I'm not an advanced user.  I'll be able to use it?  Three, you need a CD of the OS to run it, and I don't have a CD when I bought my Dell laptop.  I don't think I even offered to pay extra to get a copy (it was awhile I bought it).  Can I get a CD of the OS through Dell?  I know that you can burn a backup copy of Windows, but I only learned after the beginning of this problem.

  Any other maybe solutions?  Thank you.

  Message edited by kazoos at 14/10/2008 12:22
  Message edited by kazoos at 2008-10-14 12:23
  
  

• The button code will not replace the stop code

  Hello

  I have been stuck for days trying to figure this out and would appreciate any help offered.

  In an HTML5 document, I use excerpts of code (HTML5) to make an animation stops at some of the images in the scenario and then buttons take the Viewer to specific sections of the timeline.

  

  The Start button must essentially ignore the playback head on a structure ahead of the frame with the code to stop... but it doesn't. When I preview the video, I can click on the button, but the playhead does not advance the flag "getgoing. I tried this with both specific chassis numbers, but that no longer works.

  I did test files containing a single button and the stop code and everything works fine. But in this file larger with several going on, the buttons stop working. Certainly, I have imported image sequences that I made in After Effects (my favorite animation software) and Animate takes more time to save and preview because of this. I don't know if the mere fact of having sequences of images as graphic symbols would change the functionality of a button, but I'm not nothing throw.

  Thank you!

  The debugging 101 button: first thing make sure that the event handler running one) in fact, b) to what you think it is targeting. The two goals can be accomplished by sticking a trace() statement in the button click event handler that prints everything that you target your call gotoAndStop(). For example, if you have this:

  paramecium.panda.parallelogram.gotoAndStop (451);

  Add this entry:

  trace (Paramecium.Panda.Parallelogram);

  If nothing prints when you click the button, or it prints "undefined", you will have significantly reduced the problem.

• Re: hp stop code

  Hi, locked out my computer bios on hp pavilion laptop have a stop code 86402351 any help would be appreciated?

  Hello:

  Enter the unlock code:

  39560997

• Satellite Pro M70 - Windows XP has stopped working - registry problems

  My M70 lost (I will follow soon!). Windows XP has stopped working, registry problems. I finished by using the Toshiba Recovery disk and reformat the hard disk. Said again there is some registry problems and crashing.

  One had similar problems?

  Phil

  Hi Phil,

  If your laptop is always report registry errors after having re-installed the operating system from the recovery disc, then it is likely that your hard drive has errors. The Windows XP registry is composed of several files (or urticaria), and the installation process will always be located in the same area of the hard drive.

  Kind regards

• Hp246: Stop code 60016543

  I forgot my administrator bios password and I get the stop code 60016543

  @MukeshWarrior

  Enter 75974585

• I have a mini hp x 64 or and my stop code is CNU9254R4M I forgot the password please help

  I have a mini 1116nr hp, I forgot the password. Stop code is CNU9254R4M can any one help thanks in advance...

  @spiderdish2020

  Enter: e9lo7qvbv4 (3rd character is a lowercase L)

  Kind regards

  DP - K

• Compaq RT3290-C2: stop Code / COMPAQ

  Hey, need a little help here :/

  My stop code is 55020283

  I can't access the computer without the BIOS password...

  Thank you!
  
  EDIT: don't know why my message has ended up here, I wanted to write it here: http://h30434.www3.hp.com/t5/Notebook-Operating-System-and-Recovery/Bios-Password-Halt-code/td-p/270...

  @MatthewMurdock

  Enter 40988805

  Kind regards

  DP - K

• Lean how to run the stop code when the highest level VI ends

  Hi people.

  I am a newbie of LV with 30 years of experience in embedded SW engineering.  I searched for how to run the stop code when a VI of highest level ends.  I found many examples, but they are horribly complicated.  A little birdie told me that such a model of simple design should not be so compilicated.

  My application is an application of high tension control to disable all HV checkpoints when the SW ends.  My VI code is running in a while loop with a stop button that leads out of the loop.  I can easily accomplish my requirement by programming with a sequence of plate that runs after the end of the main loop.  The technique of flat sequence does not work when the user clicks the Cancel button in the toolbar of façade, more than that market when the user clicks the close button of the application (X button) when you run the exe application.

  Can someone tell me please a simple technique, the code example that can show me a lean and elegant way to accomplish my task?  It doesn't have to be an obvious solution (for example a stop induced watchdog seems simple enough).

  Thank you - John Speth

  1. place this code in a VI:

  (also attached)

  Calling code in your VI of highest level like this: