string of worksheet to not convert table

Similar Questions

• write the array to a string of worksheet

  Hello

  I have 3 digital paintings and 1 table.  I'm trying to use the writing range worksheet line.  What is the easy way to do it, since I have numeric and string, I can't create a table 2d directly?

  Yik

  This is pretty basic and a question frequently asked. First convert spreadsheets into tables of strings. Digital conversion functions / chain are polymorphic, you can connect a 1 d or 2d table at the entrance.

• ChnLinGenImp do not convert the value of units

  Hello

  I use the ChnLinGenImp command in a creation of such as channel below.

  --> Call ChnLinGenImp(SpecChannelName,length,SpecNumber*1,0,Unit)

  The question that I am running, I run the script for a conversion unit that converts the units if they are incorrect.  However the part convert does not convert the IMP channel, because it is a path of IMP.  Is in any way around that in addition to going to the ChnLinGen command?

  Hello J,

  Only two options I know in tiara 2012 are:

  (1) give and make a meaningful string instead of an implicit string and let conversions of unit of the tiara to manage all

  (2) manage your implicit channels separately and re-create them whenever there is a change of unit - but you have to manage the offset and the conversion factor

  For the linear unit conversions as degC to degF, I could imagine DIAdem running automatically on the offset values and factor of the implicit channel, BUT not all unit conversions are linear, and there must be able to operate on the values of the channels - you can not apply a non-linear conversion to a y = mx + b equation and get another y = I x + b' equation.

  Brad Turpin

  Tiara Product Support Engineer

  National Instruments

• string in the format spreadsheet in table: Missing comma

  Hi all

  Plug-in function "string in the format spreadsheet en table" with LabVIEW 2014. I do not understand why, but the point numbers are truncated at the output of the function.

  This is the VI as an attachment.

  Thanks for your help!

  Hello

  The decimal separator of your OS comma an EST. So either you replace it with a point or you replace the %f in your code by %; % f:.

  

• Write a string and an integer and a table all in the same file?

  Hello

  I am currently it several different types of values with LabView.

  I have a shot, a few numbers and several paintings.

  Thus, for example, I have a timestamp of the chain, several values of "integer" amplitude of the signal for example, RMS value, frequency and I have several paintings - table of signal, the FFT (PIC and location) values.

  Basically, I'm trying to find a way to write all the values in a single file. I can write all the individual types to separate files (so I can write the RMS, amplitude and frequency to a single file, some of the tables in the other)
  but is it possible to write a string and an integer and a table all in the same file?

  Pointers would be much appreciated,

  Thank you

  Paula

  Your file will be all text... any format in a table of text, to build as a single table, "table chain worksheet", to write to the file.

  (I'm sure this has been on the forums before... a search it would have thrown upward)

  

• The problem with IMP-00038 IMP: could not convert to character set environment handle

  The export was made under linux.  I am told that their settings are: (I can't check)

  AL32UTF8 NLS_CHARACTERSET

  NLS_NCHAR_CHARACTERSET AL16UTF16

  export of the version

  Export: Release 11.2.0.3.0

  I'm trying to import into an empty database in windows with the Release 11.2.0.1.0 version (a few levels below patch)

  AL32UTF8 NLS_CHARACTERSET

  NLS_NCHAR_CHARACTERSET AL16UTF16

  Select userenv ('LANGUAGE') of double

  AMERICAN_AMERICA. AL32UTF8

  my var environment NLS_LANG = AMERICAN_AMERICA. AL32UTF8

  The value of KEY_HKLM\Software\oracle\OraDb11g_home1\NLS_LANG is also set to AMERICAN_AMERICA. AL32UTF8

  IMP prod_user/password@instacnename file = exportfile.dmp see the = y

  WITH JUST SHOW = Y ON... (even with him in the distance)

  Import: Free 11.2.0.1.0 - Production Fri Nov 14 11:09:51 2013

  Copyright (c) 1982, 2009, Oracle and/or its affiliates.  All rights reserved.

  Connected to: Oracle Database 11 g Enterprise Edition Release 11.2.0.1.0 - 64 bit

  Production

  With the partitioning option

  IMP-00038: could not convert to character set environment handle

  IMP-00000: Import terminated unsuccessfully

  NO idea how to solve this problem?  I broadcast the gziped file and a new... to be sure of the xfer wasn't the question...

  I'm stumped... I searched the Forum and the web and tried most of what I found.

  Thanks in advance

  -Ken

  Hello

  I think that there is a single cause - see the example below

  expdp / schemas = bob

  Export: Release 11.2.0.3.0 - Production on Fri Nov 15 18:04:46 2013

  Copyright (c) 1982, 2011, Oracle and/or its affiliates.  All rights reserved.

  Connected to: Oracle Database 11 g Enterprise Edition Release 11.2.0.3.0 - 64 bit Production
  With the partitioning option
  Departure "OPS$ ORACLE." ' SYS_EXPORT_SCHEMA_06 ': / * schemas = bob.
  Current estimation using BLOCKS method...
  Processing object type SCHEMA_EXPORT/TABLE/TABLE_DATA
  Total estimation using BLOCKS method: 0 KB
  Processing object type SCHEMA_EXPORT/USER
  Processing object type SCHEMA_EXPORT/SYSTEM_GRANT
  Processing object type SCHEMA_EXPORT/DEFAULT_ROLE
  Processing object type SCHEMA_EXPORT/PRE_SCHEMA/PROCACT_SCHEMA
  Object type SCHEMA_EXPORT/TABLE/TABLE processing
  Object type SCHEMA_EXPORT/TABLE/STATISTICS/TABLE_STATISTICS treatment
  . . exported "BOB." » EMP"                                     0 KB       0 rows
  . . exported "BOB." "" EMP2 "0Ko 0 rows
  Main table "OPS$ ORACLE." "' SYS_EXPORT_SCHEMA_06 ' properly load/unloaded
  ******************************************************************************
  Empty the files together for OPS$ ORACLE. SYS_EXPORT_SCHEMA_06 is:
  /Oracle/11.2.0.3.0.DB/RDBMS/log/expdat.dmp
  Job ' OPS$ ORACLE. " "" SYS_EXPORT_SCHEMA_06 "led to 18:05:19

  [oracle@]:EMZA3:[~]# imp / file=/oracle/11.2.0.3.0.DB/rdbms/log/expdat.dmp]

  Import: Release 11.2.0.3.0 - Production on Fri 15 Nov 18:06:02 2013

  Copyright (c) 1982, 2011, Oracle and/or its affiliates.  All rights reserved.

  Connected to: Oracle Database 11 g Enterprise Edition Release 11.2.0.3.0 - 64 bit Production
  With the partitioning option

  IMP-00038: could not convert to character set environment handle
  IMP-00000: Import terminated unsuccessfully
  [oracle@]:EMZA3:[~]#

  Spot the problem?

  The original dump was expdp, we seek to import with IMP...

  If it is conversely impdp flags it is an exp file - but this round way you get just this random error!

  See you soon,.

  Harry

• VARCHAR2 data type do not convert date

  Dear gurus
  
  Version of database - 10.2.0
  
  I have a problem of varchar2 data type do not convert date...
  
  I have a table like
  
  
  SQL > table desc.
  Name Null? Type
  ----------------------------------------- -------- ----------------------------
  NAME VARCHAR2 (10)
  RECORD_DATE VARCHAR2 (20)
  
  and the record consists are...
  
  SQL > select * from table;
  
  NAME RECORD_DATE
  ---------- --------------------
  Nimai 09/09/2012 09:10
  Nimai 09/09/2012 10:10
  Scott 09/09/2012 11:10
  Scott 09/10/2012 10:00
  Nimai 09/10/2012 11:00
  
  
  If the "Record_date" column that's 09/09/2012(dd/mm/yyyy)
  
  09/09/2012 and I want to query the records which includes the date ' select * from table where record_date = 09/09/2012 "...
  This work of query...
  
  Select * from table where
  TO_CHAR (to_date (substr(record_date,1,10), ' dd/mm/yyyy'), ' dd/mm/yyyy')
  =
  TO_CHAR (to_date (substr('09/09/2012',1,10), ' dd/mm/yyyy'), ' dd/mm/yyyy')
  ;
  
  But if the "record_date" column that's 9/9/2012(d/m/yyyy) I did not what to do which function to use? /
  
  Help, please!
  
  Thanks in advance
  Nimai kinzonzi
  
  Published by: 955748 on September 22, 2012 03:47
  
  Published by: 955748 on September 22, 2012 04:10

  Hello;

  Keep things simple: (get rid of TO_CHAR)

  SELECT TO_DATE ((substr (record_date, 1, 10), ' DD/MM/YYYY') of?)

  TO_DATE (substr (record_date, 1, 12), "HH24 MON-DD-YY")

  Best regards

  mseberg

• How can I use the sequence of the string "\u00e5" in myfile.txt converted unic

  How can I use the sequence of the string "\u00e5" in myfile.txt converted to unicode in my application?
  
  I have a text file, MyFile.txt, with some sequences represented unicode:
  \u00e5
  \u00e4
  \u00f6
  etc.
  
  This is the file contains unicode, not the character it represents: a, a and o.
  I get the sequence of the file and save it to a vector. When I tried to use it on a JButton, I see the "\u00e5" string and not the character that I assumed.
  
  

   
          read file codes ...
          ...
       Vector<String> glyphVector = readGlyphIndex.getUnicodeFiles();     // to retrieve the vector with unicode sequence and save it to glyphVector
       String unicode = glyphVector.get(0);     //get the first unicode sequence
          System.out.println(unicode);    //displays \u00e5 and not å in the console.
       jButton.setText(unicode);   //jButton is a JButton and it shows the string \00e5 and not the character å
          ...

  The question is how to convert the sequence of string to be a unicode escape in the code?
  
  In order to make it clear:

  //from
  jButton.setText("\\u00e5");
  //to
  jButton.setText("\u00e5");

  Thanks in advance!
  
  Dragonfly

  String s = Character.toString((char) unicodeInInt);
  

  Strictly speaking, if unicodeInInt is a Unicode code point (for example, it can be greater than 0xFFFF) then the correct code would be this:

  String s = new String(Character.toChars(unicodeInInt));
  

  However, since the "\u" notation allows only 4 hexadecimal digits (and need to 0xFFFF code points > Unicode represented by their UTF-16 encoding), the code above is not enough for this particular case.

• iMovie imported my clips but did not convert the

  Hi all.

  Recently, I imported a whole bunch of my GoPro clips in iMovie. They seemed imported ok, but when I drag them from the event in the project and then decide I want to make adjustments of speed in clip adjustments, it is said that the clip was not converted - see attached screenshot.

  In addition, displaying some of the clips, some of them do not see smooth, the video will be trolling heavily but audio will continue. This will be resolved once that I convert the clip but it's a bit frustrating when I have to drag the item from the window of the event in the project window and then convert it just to see if I want to use it or not.

  The clips can be converted singularly but takes a while. I was wondering if there was a way to conversion in bulk the clips so that I could just let it run all night and she'll do all clips at once. I have searched through the toolbars, but found nothing. It is mostly just then preview or watch clips or if I want to make adjustments of speed/run the clip towards reverse.

  I made a video in iMovie earlier in the year with images of the GoPro (from the GoPro even) and had no problems with the conversion of import or clip.

  Any help anyone could give me would be much appreciated.

  PS if possible, I don't want to reimport them since I already moved half the clips I want in my project.

  Additional information:

  Computer: MacBook Pro 13 ", about six years, running the Version OS X El Capitan 10.11.4

  version of iMovie: iMovie ' 09, version 8.0.6 (821)

  GoPro used: GoPro Hero4 Silver

  

  I made a video in iMovie earlier in the year with images of the GoPro (from the GoPro even) and had no problems with the conversion of import or clip.

  Were then automatically using El Capitan, or a previous operating system?

  There are many reports on these forums that suggest that worm iMovie 8 and 9 are not compatible with El Capitan.OK on previous operating systems

  Even if you convert the clips there may be other issues.

  The recommendation, if you have problems with the 8 CBS NVA, is to download iMovie ver 10 from the App Store.

  It is not free for users of version 8 it is for users of version 9.

  Version 10 is quite different from 8 and 9 so a bit of a learning curve.

  Do a search here for compatibility with El Capitan iMovie for more information and look for entries of GeeD is the current master

  for iMovie 10 and how to get your events and projects in iMovie 8/9 to iMovie 10.

• I just recently upgraded to OS El Capitan.  Now, none of my movies to quicktime does not work.  I have the old version of Quick time 7 and it does not work either.  They do not convert.  Help?

  I just recently upgraded to OS El Capitan.  Now, none of my movies to quicktime does not work.  I have the old version of Quick time 7 and it does not work either.  They do not convert.  Help?

  VLC will play them?

  http://www.videolan.org/

• House of memories Play do not convert the FH on Standard DVD video

  I've just updated House memories of game to Version 3 of 2, now it will not convert the video files in FH on DVD standard. It is used for version 2. It is no longer supported? I get error that says that "some media files are not written to the disk as they are in file formats that are not supported".

  I am able to create AVCHD discs with no problems. Version 2 would convert these files so that I could make copies of DVDs also regularly.

  Thanks for any help.

  Well, when all else fails, uninstall and reinstall. Has worked with aid and they have recommended that. It worked. Should have done that in the first place but upgrade seemed to work fine except for that. Now it works very well for AVCHD and DVD Standard from FH video files.

• Ultiboard DXF to Gerber Polylines do not convert to polygons

  Hello

  I am trying to import a DXF to ultiboard antenna file and export it as a file gerber.  The DXF has two layers, edge contour and copper, I chose merger to the Board outline and the copper top.  I also check the option "Convert polylines, polygons", but when importing, there is no area of polygons/copper, just as traces of copper imports as you can see in the screenshots.  No idea why the polylines are not convert?  Dxf was generated from solidworks, so I am confident that the pads are closed areas.  At the bottom of the antenna, you can see there is even a text (part number) which clearly would be closed, but is not a conversion.

  This article is basically said to check the option "Convert closed polylines to polygons" during import, which as I said, did not work for me.  But for anyone else having this problem, I solved it by editing the dxf file so that areas of copper I filled, were met.  Then when I imported dxf updated the ultiboard, they properly imported as areas of copper regardless of whether or not the option "Convert closed polylines to polygons" was checked.

• DAQmx (Version 9.1) Create Channel for accelerometer will NOT convert m/s ^ 2

  I use DAQmx create channels for accelerometer to get results in the unit (m/s ^ 2)

  It worked until DAQmx Version 8.9.

  Now, I tested it with DAQmxVersion 9.1 and the results are in g (not converted to m/s ^ 2!)

  I use wth .vi DAQmx Create Channel (I-acceleration-accelerometer) entries

  units = m/s ^ 2

  sensitivity units = V/g (there is no sensitivity unit V /(m/s^2) available)

  sensitivity sensitivity value in V/g =

  I have read the data with

  . VI DAQmx reading (analog 2D DBL NChan NSamp)

  In DAQmx<= 8.9="" the="" double="" numbers="" are ="" correct="" converted="" to="">

  but in DAQmx 9.1 not (values are in g and low by 9.81)

  My solution is the following change

  units = g

  sensitivity units = V/g

  sensitivity = sensitivity value in V /(m/s^2)

  Then the double numbers are not converted, but m/s ^ 2.

  And this work in all versions of DAQmx.

  The problem is:

  An older program that uses the settings of the first and tested with DAQmx<=8.9 will="" get="" wrong="" measurement="" result="" with="" daqmx="" 9.1="" and="" no="" error="">

  Peter

  Hi Peter,.

  I'm not in my office at the moment and I can't try it by myself, I have forwarded your request to one of my colleagues, I hope he will contact you soon.

  Sorry for the delay,

  Tobias

  The language of MAX settings depend on the regional settings of your Windows operating system. See the following page:

  http://digital.NI.com/public.nsf/allkb/9893C1767C93D20E86256F49001CDA92

  Kind regards

  Tobias

• How to convert table 1 d scalar

  I use PMD-1208LS to get 2 entries through 2 different channels, using AInScFg.vi

  How ever, the values in table 1 d [of the digital (only 32-bit real)].

  After you have applied several equations on the Board he still table 1 d but [Digital (real 64-bit double)], now I want to send to the output channel using Eng.vi--> Aout.vi.

  The problem is, that may come on if my data is in the scalar data type [sink data are unsigned word (16-bit)] no table type?

  So, how can I convert table 1 d scalar (Word)?

  Thank you

  You can do it the way I suggested or Gaurav method. You like.

• SMC will not convert.

  My SMC will not convert the videos that ask him too. I'm going to click on "Add media" and choose one of my videos, so it'll get back with a review "this file, C:/bahbhawhereeveritis can not be converted. Please install the codec to corect first. If he can play on your PC, it must be able to convert.

  The problem is that my PC can read the .mpg files and files .mp4 and .avi, then why not SMC convert it?

  Thanks in advance,

  Mark

  PS I have the latest version of the downloaded SMC yesterday,

  shmince wrote:
  I disagree with you on the video thing, as I have 35 more hours of video on my rocket currently. I ripped out the DVDs and downloaded video files. Have you tried AnyVideo converter? Stick with conversion to mpeg and avi before their execution via the MSC and you should be in business. Also, make sure you have enough room on your platform or the conversion of SCM will fail.

  I use anydvdconverter (same as any videoconverter really).  Then I put them on the SMC and they convert very well.

  shmince, how many GB you have for 35 hours of video and more?