Sucks TC-605 card Interface

Similar Questions

• Sucks tc-605 internet problem

  Hello my sucks tc-605 does not connect to the internet with a cable, it shows, in connections, network not identified and limited (I can connect with a wi - fi). If I try to connect the same cable to my laptop, it works.

  I have a problem for about a day connecting the cable worked perfectly so far and I have the PC for about 2 months.

  I really want to re - install windows.

  Version of the OS?

  Have you already tried to uninstall the network card and re - install the drivers?

• No audio output device installed on sucks TC-605 with Win 8.1

  I had to reinstall the drivers on my sucks TC-605 Win 8.1 running everything seems to work ok, except that I get a no audio output device installed.  I have tried everything I can think of, including the removal and reinstall all the drivers, deactivation and reactivation of the hardware in the Device Manager.  I think that perhaps there is a secret in order that the Intel Chipset drivers are installed before the Realtek audio drivers?  I've seen a lot of reports on various web sites and some that reference the Windows Audio service is restarted.  I tried ALL these "fixes" several times, but no luck!  Any help to diagnose and resolve this would be greatly appreciated.

  HDAUDIO\FUNC_01 & VEN_8086 & DEV_2807 & SUBSYS_80860101 & REV_1000

• Sucks TC-605 BIOS HELP!

  Hello everyone, I need some serious help. Yesterday by updating my PC, I searched the Acer site and saw a BIOS update for my model. I downloaded and it seemed very confusing to me. I decided to not update, later, my uncle came and said that he knew how to do. Long story short, after that he did my Acer won't start, I press the power button, I get a short beep and the HARD drive lights flashes for a second, then black screen only. Anyone with any help much appreciated.   SYSTEM SPECS: Aspire Asus pro TC - 605 - UR2S Windows 10 GT 630

  As I said earlier, if you initially had Windows 7, then your BIOS was in legacy mode (secure boot disabled, csm launch set to 'always'.

  If you need to go to the BIOS settings and disable secure boot and change the 'csm launch' forever.  Or start secured bare minimum disable.  It might possibly work with CSM launch set to never, but I'm not.

  The link below explains all.  You can use the P11. B4, but P11. B4 is for computers that came pre-installed with Windows 8,8.1 and 10... but given that your computer came pre-installed with Windows 7 you need to understand the difference between legacy mode and mode default EFI and you must understand the difference between a partition MBR one style vs style of GPT partition, if you want to use P11. B4 on a computer that came pre-installed with Windows 7.  If you do not understand these things, then it is preferable for you to use P21.xx.

  http://Acer--UK.custhelp.com/app/answers/detail/A_ID/27071/~/how-to-enable-or-disable-secure-boot

  You can re - install Windows 10 in EFI mode, which would be much more secure, but you must completely wipe your drive first, if you want to do.

• How card interfaces NIC to NIC physical specific comments

  I have a virtual machine with two network cards, eth0 and eth1 (Linux).

  My guest VM is connected to a virtual swtich, vswitch0 which is connected to the physical NETWORK card eth0. I also have a different physical NETWORK eth1 card.

  How do I map my virtual machine

  -> map virtual eth0 eth0 physical and

  -> map virtual eth1 to eth1 physical.

  So currently I VMachine (vNIC eth0 and eth1)->-> physics eth0 vswitch0

  I don't want to vNIC VMachine eth0->-> physics eth0 vswitch0

  and

  VNIC eth1 of VMachine-> vswitch0 (or other)-> physical eth1

  Thank you!!

  Configuration > networking screen, you can add an another vSwitch.  The wizard will take you through the process and you can add the vSwitch vmnic1.  You click Add Network, and then select the type of Virtual Machine.  On the next screen, you can create a new vSwitch.

  Next, you will change your VM to set network for eth1 label match the name port group of virtual machine that you created.

  Are the two physical network adapters on separate local networks?  You could have both in the same vSwitch and then segment your networks with the VLAN.

  Dave
  VMware communities user moderator

  ESXi Essentials free training / eBook offer

  Now available - VMware ESXi: planning, implementation, and security

  Also available - vSphere Quick Start Guide

• Acer sucks TC - 605 no signal when connected to 10 Windows HDTV

  I start my PC, see the Acer logo in the center of my screen and can access the configuration from there.

  As soon as the logo disappears my tv gives me a message "no signal".

  I tried with 2 hdmi, both give the same results, but do not have another monitor to test on.

  is probably a bad driver VGA, you can try to resolve this problem, uninstall drivers windows safe mode VGA.

  http://www.TomsHardware.co.UK/FAQ/ID-2569556/safe-mode-Windows.html

  You can try to enter windows 10 recovery by pressing Alt + F10, and then follow the instructions on the link above.

  If you are unable to enter safe mode, you will need to download a 10 bootable windows installation media and use it as a recovery disc to activate safe mode.

• Multiple Crypto cards on simple external Interface

  Hi, I got the following encryption card configured on my ASA5505 to allow Cisco IPSec VPN clients to connect from the outside:

  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set

  Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5

  outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

  outside_map interface card crypto outside

  I'm now trying to set up a map of additional encryption - a static configuration to establish a tunnel with Windows Azure services. The configuration, they gave me is:

  Crypto map Azur-crypto-map 10 correspondence address azure-vpn-acl

  crypto azure-crypto-card card game 10 peers XXX.XXX.XXX.XXX (hidden)
  

  card crypto azure-crypto-map 10 set transform-set of Azur-ipsec-proposal-set

  Azur-crypto-card interface card crypto outside

  However, when I apply this configuration, my Cisco IPSec clients can connect is no longer. I think that my problem is that last line:

  Azur-crypto-card interface card crypto outside

  that blows away my original line:

  outside_map interface card crypto outside

  It seems that I'm stuck with just picking one of the maps to apply to the external interface. Is there a way to apply both of these cards to the external interface to allow the two IPSec tunnels to create? We lack ASA version 8.4 (7) 3.

  Hello

  You can use the same "crypto map"

  Just add

  card crypto outside_map 10 correspondence address azure-vpn-acl

  crypto outside_map 10 card game peers XXX.XXX.XXX.XXX (hidden)
  

  card crypto outside_map 10 set transform-set of Azur-ipsec-proposal-set

  Your dynamic VPN Clients will continue to work very well that their statements "crypto map" are in the order of precedence / low in "crypto map" configurations (65535) and VPN L2L is higher (10)

  And I want to say with the above is that, where a connection VPN L2L is formed from the remote end it will be naturally VPN L2L configurations you have with the number of configurations "crypto map" '10'. Then when a VPN Client connects it naturally will not match the specific configurations of the number "10" and will move to the next entry and the match (65535)

  If you happen to set up a new connection VPN L2L then you might give him the number "11" for example and it would still be fine.

  Hope this helps

  -Jouni

• Acer AspireTC-605 Office Tower, someone added a fan turn on this unit and plugged

  Could someone install one on the counter of the fan at the Tower a sucks TC-605? This office is not dating one, and I expect the weather warmer heat it will affect. I wonder if the fan is simply connected on the motherboard without frills since I'm not particularly skilled enough to operate on a computer... Thanks for any help...

  Are you talking about how to add a case fan or talk to replace the stock with a better fan CPU fan?

  I don't think that the hot weather will affect it.  According to your textbook, the ATC-605 has a level of operation of 5 to 35 ° C (41-95). These temperatures are the times of the room.  As long as your House is less than 95 degrees Fahrenheit, you will be within the range.

  I'd leave the CPU fan only if you're not too tech savvy.  I've seen people replace their stock CPU fan and cause more harm than good because they didn't know what they were doing.  Generally what happens is they remove the heat sink and do not realize that they screwed up the thermal paste on the cpu/heat sink.  My neighbor took his CPU fan and heatsink of heat and really destroyed his circa 2006 AMD CPU.  I told him that he messed up his thermal paste, and he replied: 'what is thermal paste? Your CPU of 605 ATC has an auto protection function and it will cut up to idle before he self-destructs should never be too hot.

  It is possible to add a case fan and connect it to one of the available outside the power molex connectors.  There can be no cruise control.  It will be "always on" when your computer is turned on.  But I don't think that you need an additional case fan.  Modern electronics is designed to operate at temperatures much higher than before to be.  In any case, I'm pretty sure that there is not a port available on the motherboard to connect a case fan that would allow the automatic speed control.  But you would need just to screw (hang) in side of the case and connect to molex.

  You can check your temperature and temperature of the motherboard CPU with Soluto.  Soluto is one of the applications that is preinstalled on your computer. The UEFI/BIOS will also show you your time.

  I guess I have might consider adding a case so fan the temperature of the CPU never went more than 69 degrees C (156 F).

• Evacuation of the queues on Cisco 6504-E and 6509-E Cisco line cards

  Hello

  In our network environment, we get the following configuration:

  Cisco 6509-E(Sup-2T) as the main switch equipped of line card module WS-X 6848-SFP (1 GE)

  Cisco 6504-E (VSS-720-10 G Sup) as long as the service of distribution layer switch equipped WS-X 6704-10GE line card module

  .

  Time modules line cards end Layer 3 connections from the layer of access/core.

  The QoS trust status is ""DSCP ' on line card interfaces and 6504-E 'mls qos trust dscp' is explicitly configured to trust the DSCP values. "           As is clear from interface capacity output below, "QoS queueuing" mode on both cards line is "CoS" only, and DSCP evacuation lines is not available in interface ' wrr-tail ' configurations. Similar problem exists on the interfaces of channel member of port on the main switch Sup - 2 t as well.

  CORE01 #sh int gig2/1 cap

  GigabitEthernet2/1

  Model: WS - X SFP-6848

  Type: 1000BaseSX

  QOS scheduling: rx-(2q8t), tx-(1p3q8t)

  Queueing QOS mode: rx-(cos), tx-(cos)

  VSS01 #sh int t1/2/1 cap

  TenGigabitEthernet1/2/1

  Model: WS - X 6704-10GE

  Type: 10Gbase-LR

  QOS scheduling: rx-(8q8t), tx-(1p7q8t)

  Queueing QOS mode: rx-(cos), tx-(cos)

  CORE01(Config-if) #wrr - queue?

  minimum bandwidth of WRR bandwidth set with weights or percentages

  cos-map set up cos-sheet for a queue threshold ---> Cos map only no. DSCP

  the queue limit configure the queue limit

  detection of random set up the random detection

  the bandwidth of the SRR maximum queue set up with weights of form or

  percentages

  tail-drop threshold thresholds configure queue

  VSS01(Config-if) #wrr - queue?

  minimum bandwidth of WRR bandwidth set with weights or percentages

  COS-map set up cos-sheet for a queue threshold---> Cos only no. DSCP map

  the queue limit configure the queue limit

  detection of random set up the random detection

  tail-drop threshold thresholds configure queue

  In the above scenario, how the evacuation of the queues should be applied and what are best practices? If 'wrr-tail' is not supported for DSCP, it's recommended to set up "Political map" for evacuation queues and/or any other configuration of queues and then apply the policy of the outgoing evacuation on the interface function. Also, if the queue of political output card config is used, this allows for all the other DSCP / COS line cards in the system, so that the configuration is compatible with the network of 6500.

  Thank you and best regards,

  Mohan

  :

  Disclaimer

  The author of this announcement offers the information in this publication without compensation and with the understanding of the reader that there is no implicit or explicit adequacy or adaptation to any purpose.  Information provided is for information purposes only and should not be interpreted as making the professional advice of any kind. Use information from this announcement is only at risk of the reader.

  RESPONSIBILITY

  Any author will be responsible for any damage that it (including, without limitation, damages for loss of use, data or profits) arising out of the use or inability to use the information in the view even if author has been advised of the possibility of such damages.

  Poster

  My understanding is that you use wrr-queue cos-card as you would be for the CoS values understand the DSCP values have been mapped in these CoS values.

  If you look at figure 2-25, in the reference I provided, you will see 'Final internal DSCP is mapped to CoS' and ' "DSCP-CoS > rewrite" when dealing with exit port QoS. "

• Wireless internal card speed is 150 Mbps?

  HP p7-1007

  If I use my netgear usb adapter speed goes straight to 300mbps and stays between 270 and 300 consistantly. Unplug it and right back to 150 on the internal card. Someone at - it understand why?

  Maybe it's because it's spec'd for 150Mbps by HP.

  802.11 wireless b/g/n Mini PCI-E card
  Interface type: PCI-e card mini half-length
  Data transfer speed: up to 150 Mbps
  Communication standards: 802.11 b/g/n
  Support for connecting antenna: 1
  Operating band: 2.4 GHz
  Support for the security protocols: WPA, WEP

  http://support.HP.com/us-en/document/c02871202

  Frank

• Tecra 8000: update of the Bios allows booting from USB?

  Hello

  I have Toshiba Tecra 8000 (simple 266 MHZ)
  Will be this bios bios-t8000-930 - trad.zip (08/26/02) allow you to boot from USB?

  Hello

  As far as I know, you need a supported drive to boot from external USB drive.
  The update of the Bios won't boot options.
  If you want you can ask for the readers supported ASP.
  I found this site one:
  http://www.CCD.co.UK/Xpress/catalogue/product.asp?PN=JD0000283

  It s a Toshiba CD - RW / DVD-ROM combo wit reader PC Card interface.

• Thr type hbitmap in the labview

  Hello

  I had a Dll located in the internet.

  Now, I want to use "Call library function node" to get the data of this DLL.

  Unfortunately, I don't, t know how to set the "HBITMAP" without knowing the type of law in labview.

  the code of the DLL: extern "C" __declspec (dllimport) bool __stdcall DataMatrixDecodeBitmap (HBITMAP hImage, char * pResult, int * pSize, int nTimeOut);

  

  Is any body knows the right type of HBITMAP in the labview? Table? or labview can, t take charge kind of guy.

  Any suggestions would be much appreciated.

  Thank you

  Hello

  try looking in the header, what is this type of data. It can be a custom structure defined in this file. If so, thread a cluster with the same elements that are in the structure.

  EDIT: found on google

  --------------

  Although Windows handles are under 32-bit Windows for most of the pointers to memory
  It would be a bad idea to try to directly access these data. Windows handles are
  supposed to be types of opaque data whose internal structure is only known for Windows
  and more specific to Windows versions that are similar or better than the one that created it.

  The Windows API gives you (almost) all the specific access features
  information inside a handful. HBITMAP would need to access the API
  function GetDIBits(). This function works with a HDC device context handle you
  probably need to get your capture card interface. This is necessary to convert
  device-dependent in a HBITMAP independent unit information
  (the GetDIBits DI) information in the settings that you want to receive.

  -----------------

  So, here's an I32 or I64, depending on your system. It is a pointer to a memory space.

  And here is a previous discussion: Forum OR

• GPIB488.2 head and lib files

  I use NI GPIB-HS-USB for communication between the computer and the Dynamic Signal Analyzer(,DSA,SR785,made by Sranford.). I intend to schedule with VC6.0 and control the DSA with HS-GPIB-USB. Unfortunately, I can't find the file head NOR and circulations files providing the access interface to the GPIB.

  Please send me two files. I thank you kindly for your help.

  With my best wishes,

  Zhao.

  E-mail: [email protected]

  Zhao Hello,

  Each GPIB Instrument has a primary address (PAD) and possibly a secondary address (SAD) that correspond to the parameters of 2nd and 3rd took the call to ibdev. Each GPIB Instrument must in turn be associated with a GPIB Interface (usually referred to as the "Board" or "Board index" in the documentation) which is the first parameter in the call to ibdev. A GPIB card/Interface can communicate with up to 16 Instruments GPIB. If you have several GPIB Interfaces or advice on your computer, each of them can communicate with up to 16 Instruments GPIB. The GPIB driver software needs to know what Instrument GPIB is connected to what card/Interface GPIB, and this is why you must specify the "BdIndex" (or Board index for the particular GPIB Interface Board) in the first parameter of ibdev.

  Say, for example, you have a GPIB Instrument with the PAD 3 (but no SAD for which just enter '0' to indicate no SAD) which is connected to GPIB1 (its BdIndex = 1), the first 3 parameters in the call to ibdev would look like the following:

  ibdev (1, 3, 0...

  But if you have only one card/Interface GPIB in the computer, it's default value GPIB0 (his BdIndex = 0), the first 3 parameters in the call to ibdev are:

  ibdev (0, 3, 0...

  I hope this clears it as to why you need a Board index as well as the primary address.

  gpibtester

• Driver missing in Windows 10

  I have improved my moms to 10 Windows pc. The model is ATC-605-EB1C (Aspire) which I believe is sucks TC-605 on the Acer web site.

  Series No.: [redacted to comply with guidelines]

  Now, once Windows 10 is installed, there is only 1 device which is exclamated outside. PCI Simple Communications controller

  I went in the section of the driver and I installed buth LAN as well as the wireless and it still has an exclamation point.

  Any ideas?

  Thank you

  Joe

  joerobertson,

  I'm prety sure it's related to the intel AMT or engine of intel or BIOS or a combination of all three.

  I have two computers of TC - 605 and don't get this exclamation with Windows 10 although I noticed it after a clean installed Windows 8.1.  After a clean install of Windows 8.1, going to downloads Acer and install the iAMT driver solves this problem.

  I was curious, after installed Windows 10 cleaning or not this exclamation of controller PCI simple communications would appear, but to my surprise, it didn't.

  So, based on what you say, I wonder if your computer comes with Windows 7 pre-installed or you are using an older version of BIOS?  Two of my computers are preinstalled with Windows 8.1 and both have been updated to the latest BIOS for Windows computers of TC-605 8.1 which is P11. B3.

  Edit: What BIOS version came pre-installed on your computer?  To check the BIOS version on your computer, you right-click on the Start button, select run Windows and type "msinfo32" without the quotes.

  Edit2: Two of my computers also have the chipset driver intel 10 Windows and Windows 10 intel management engine driver installed that I downloaded from the Acer site (but still once, I don't have the exclamation even when I have not... makes me think it might be related too BIOS).

• I need a part number for a dv9000 series audio connection motherboard Intel... Please.

  I have a HP dv9723cl that I finally gave up on due to some problems with the motherboard that no one seemed to have ideas for. Well, I bought a replacement motherboard, but accidentally bought a motherboard Intel instead of card mother AMD that was originally there. Now I'm trying to put it in, and all connects together fine (after buying another CPU and CPU sinks) with the exception of the little girl that the ir receiver and the audio jacks are mounted on. The end of the cable that connects to the motherboard is too broad for this replacement motherboard.

  Someone at - it a part number for the correct audio Panel? I bought 2 different audio cards with 2 different numbers just in the hope that one of them has had reason, but none were correct. Both had the same wide end to the connection on the motherboard.

  Please, someone, anyone, tell me if you know the right part number, or where to find it. Or maybe even a link eBay at good advice if you feel generous.

  The following were found from the parts for a DV9650US page .

  It seems that the audio Platinum for this device, which uses the same motherboard you purchased based on the number of the piece, is 449763-001.

  Printed circuit board (Interface)
  		432987 001	The power button - includes power cable key board IS NO LONGER INCLUDED		N	N/A-	Modified
  		432991 001	Wireless switch board - includes cable wireless switch Board IS NO LONGER INCLUDED		N	N/A-	Modified
  		432992 001	Optical disc drive connector Board IS NO LONGER INCLUDED		N	N/A-	Modified
  		448437 001	Platinum connection of USB ports IS NO LONGER INCLUDED		N	N/A-	Modified
  		449762 001	Before USB ports connection Platinum IS NO LONGER INCLUDED		N	N/A-	Modified
  		449763 001	Map of circuits audio and infrared (IR) - contains the IR receiver, microphone, line-in and taken helmet IS NO LONGER INCLUDED		N	N/A-	Modified

  I can't guarantee that the audio card, that this unit has will align with your current deal.

  What I would recommend enter the part number of motherboard on the HP PartSurfer link above and re-cutting references printed circuit card (Interface) until you find the one that matches.

  A quick comparison returned this page for your laptop current.  However, there were more different hardware configurations a dozen for the model you listed.

  To get anything specific, I'll need the product number of the unit.  The product of the listed number is gp348av.

  NOTE: Provide NOT the serial number.