Survey on the site - TX power level
I use on site (EKAHAU) for the investigation of one of the dormitory building.
I get a different strength of signals from various points of access (Cisco LAP 1131)
My questions are: should I change all points of access to transmit at full power or leave it set on a global scale?
Y at - it because of level of power tx (range 1 to 4).
Allen
I would leave it alone. If your APs are focused on the controller, then if a PA must be detected has not filled by the controller, then the controller can ramp up of the transmission power.
Tags: Cisco Wireless
Similar Questions
-
How one doesn't check the battery power level?
How is - a check the battery power level, rather than just waiting for the clock to tell me that it is 10%?
The watch face, dragging up and show your looks. Swipe to the left to the right to find the battery look.
If you don't see it, on your iPhone, open the application of the watch and under the eyes, don't forget it's on.
It can also be added as a Complication to a lot of faces watch so it is always visible.
-
How to extract the signal from the waveform of my power level designated?
Hi all
How can I extract the signal of the waveform accroding to the power level? I read the Trigger & Gate .vi, but this vi retrieves the signal duration. I want to extract the signal depending on the power level.
As shown in the following figures, the signal I want to deal with is between 130000 to 140000, if I Zoom, I can see the useful signal is between 135400 to 138200. The question is how to extract the signal in the area?
I tried the sub_NoiseEst_And_Chop_Shell.vi in the example of Packet_based_link also, but this Subvi seems to be a bit slow. Can someone give me the best advice? Thanks in advance!
I'm working on something similar, but have not had time to fully develop.
My idea was to use an envelope detector (low pass filter) and then use a detection of energy VI on the envelope.
Here is where I left
-
I am unable to connect to the site of reliance power.
This is the New Zealand question: I tried to open a session on Trustpower website with an energy of number and a password given to me by Trustpower. I spoke to 2 people of this problem and they have proved to me that they can lohg to and view my account which is what I want to do, but can't
Original title: hard to connect to an energy supplier to view my account details
Hi BryanMcIntyre,
Thanks for posting in the Microsoft Community.
In addition, how are you doing today?
You have a problem with the connection to the site of reliance power. This can be very frustrating for you, and I appreciate the efforts you have put in. Let us work together as a team and try to get this fixed number.
We start with a few questions-
(1) the expression that exactly happens when you try to connect to the site of reliance power?
(2) do you get any error code or error message?
(3) you are able to view the Web site?
(4) is this specific issue on the site of reliance power?
(5) have you tried logging on to the site from another computer (running the same version of Windows)?
(6) what is the version of Windows installed on the computer?
(7) what is the version of Internet Explorer installed on the computer?
I would like more information about the issue.
Method-
I would have you look at the article-
Can't access some Web sites in Internet Explorer
http://support.Microsoft.com/kb/967897
Note: The feature reset the Internet Explorer settings can reset security settings or privacy settings that you have added to the list of Trusted Sites. Reset the Internet Explorer settings can also reset parental control settings. We recommend that you note these sites before you use the reset Internet Explorer settings.
If the problem persists, I would like you to contact technical support to be able to trust.
Check out the link-
http://support.TrustPower.co.nz/
We know if you need help. We will be happy to help you. We, at tender Microsoft to excellence.
Thank you.
-
Original title: cannot set a power scheme in Power Options
Cannot set a power scheme. When I try to save the scheme, "Manager power strategy impossible to define the... two revision levels are incompatible."
How can I fix it?
Hi BernieHopkins,
1 have you properly previously defined the power scheme?
2 have you made any hardware changes or software on the computer before this problem?
3. What is the full error message that you receive?
If you receive the same error as mentioned in this link, you can follow this link & check if the problem persists.
Hope the helps of information.
Please post back and we do know. -
Power level of the access point
I am running 7.0.164 WCS and series access point 1130 firmware 7.0.98.0.
I get a lot of complains about the students that their laptops do not get 5 bars signals. They receive at least 1 or 2 bars with being disconnect the frequency.
Problem is that the 2 closest access points are power TX 2 level. For the purpose of the test, I increase the level of tx power to 8 on access points and signals 5 portable bars, see the.
The dorm is 3 (2 rooms / 2 persons per room more bedroom bathroom and living room) suites by the wings. The walls are concrete.
I was told that using the custom for the TX power level setting is not recommended.
What are the solution to this problem? Use the custom setting or what?
Allen,
Your description of the problem that is absurd, especially considering that a power of 8 level is lower than the power level 2.
If you do a ' show config ap 802. 11A '
It will show you this
TX power
Number of supported power levels... 5
TX 1 power level... 11 dBm
Power TX 2 level... 8 dBm
Power TX 3 level... 5 dBm
TX 4 power level... 2 dBm
TX Power Level 5 dBm...-1
TX power setting... Automatic
Current Tx power level... 5If you do a ' show config ap 802. 11 b '
It will show you this
TX power
Number of supported power levels... 8
TX 1 power level... 20 dBm
Power TX 2 level... 17 dBm
Power TX 3 level... 14 dBm
TX 4 power level... 11 dBm
Power TX 5 level... 8 dBm
TX 6 power level... 5 dBm
TX 7 power level... 2 dBm
TX Power Level 8...-1 dBm
TX power setting... Automatic
Current Tx power level... 8So based on the fact that you said that Power Level 8 gives you a stronger signal is suspicious to say the least.
I hope this helps... Please evaluate the useful messages.
Thank you
Kayle
-
Hi guys,.
Witnessed: 5520 WLC, access points in high density, concrete walls. APs of 1832.
Version of PTC Optimal coverage Mode (TPCv1) Energy level assignment Automatic Setting level maximum power (-10 to 30 dBm) 30 Assignment of minimum power (-10 to 30 dBm) level -10 Power threshold (-80 to-50dBm) -70 Is it acceptable to configured statically the power level of the APs to customize level 1 instead of use the RRM (which normally gives 7 * or 8 *)?
Or do I have to set the configuration of the minimum and maximum power level?
Does hysteresis must also be changed?
Kind regards
I
Is it okay to statically configured the power level of the APs to custom level 1 instead of using RRM (which normally gives 7* or 8*)?
N ° it is not recommended to increase the level of AP 1 power at all times. This will lead your customer very good signal strength see, but they cannot communicate with AP as client machines cannot match the power level of AP. try always to match power level of AP to average power capacity of client if you want to set manually. Otherwise, leave to RRM to decide. If you see RRM set 7 * or 8 *, the power level indicating the deployment of dense AP where there APs on the same channel.Or should i adjust the configuration of minimum and maximum power level?
Yes, it is a good idea. For example, in my network, I put 8dBm min and 17dBm as max under PTC value for the 5 GHz band. HTH Rasika * Pls note all useful responses *. -
For the power level icon is missing from my taskbar. How do I find and get it again showing the taskbar? I've tried the suggestions help and read the FAQ, but in vain.
Hi Dee Gilles,
Welcome to the Microsoft community. According to the description, power icon is missing from the taskbar.
· Did you do changes on the computer before the show?
I'll help you with this problem. I suggest you follow these methods.
Method 1: Follow the steps in the article.
Method 2: Scan the System File Checker (SFC) to repair corrupted files.
I hope this helps. Let us know if you need help with Windows related issues. We will be happy to help you.
-
ASUS laptop computer only connects if I'm sitting next to the router loses power after a few feet
- ASUS laptop computer only connects if I'm sitting next to the router loses power after a few feet
- new laptop
I have the same problem with this ASUS Ultrabook. New brand ASUS but in two different houses and I have the same problems. Get right next to the router and it connects ok. Get a few feet away from the router and the ASUS gets angry and does not connect. Downloaded the latest driver, but that did not help either. Obviously, this is a faulty piece of equipment in the laptop. Great joy!
-
Hi all, I have attached to an external vendor bank in an OU to the site account and provider is global. This RIB is not filling at the fatcure level when creating invoice in the same OU
Hello
Is the defined account currency and the currency of the same as the currency of invoicing supplier site? It will not default if they are different currencies.
Cheryl
-
Where are the best sites for high-level and how information to do different things in Oracle?
HelloWhere are the best sites for high-level and how information about various things in Oracle?
Some examples of things:
* spa
* spm
* db replay
* Resource Manager
I need a place high-level
and also a place of step by step.
For example, I look at these sites:
Thank you Roger
Part of the problem is not so much finding sites that have articles on Oracle, that is to find reliable websites with this information. When I search my site of certification for resources, I find a significant number of people who have 'technical' Articles on Oracle. However, many of these blog posts have simply no useful information. It is not even that they are wrong so far as article does not include anything that is not declared more clearly and in detail in the documentation.
That said, a site you have not mentioned above is the Oracle Learning Library. There very often an excellent material that is very closely linked to the themes of the certification:
-
ShowDetailFrame-customizing the user get stored at the site level.
We have a show-detail-image in our page. When running it gives the possibility to move up/down etc.
When a non-administrator user moves a section upward, its reflected to all users. When I exported MDS, I found that this customization is get stored at the site level.
Is there a way to define these operations such as level of customization of the user, so that only the user who uses the options get affected?
My web.xml to CHANGE_PERSISTENCE is
< context-param >
org.apache.myfaces.trinidad.CHANGE_PERSISTENCE < param-name > < / param-name >
oracle.adf.view.page.editor.change.ComposerChangeManager < param-value > < / param-value >
< / context-param >
Thank you
Pauline.
Hi again.
I was doing a little PoC and you have the following approaches:
- Change of adf - config.xml file to use UserCC instead of SiteCC. Implement your own UserCC based on Andrejus or official documentation to retrieve the name of user of the API.
- If you need both UserCC and SiteCC at the same time you need to implement yourself. You can follow the construction process (spaces).
http://andrejusb.blogspot.co.UK/2011/09/making-it-work-together-MDS-user-and.html
I hope this helps.
-
establish the level thread redirects on the site
(Try a new thread and shape as my message seems to be drowned in the forum thread "we are to modernize the OTN Forums! This is the place for your questions and comments. "
to )
Salvation (Sonya Barry)
Currently
at https://wikis.oracle.com/display/Forums/OTN+Forums+Migration+and+Upgrade
He said: "... we delayed the launch so that we can establish level thread redirects on the site...» »
Does this mean that the URL behind the "Permlink" (green icon), currently on the top of each forum thread, will continue to work (redirect to the same information)?
for example 11.1.2.4.0: Java version 1.6.0_24 not supported... it takes 1.6.0_35
Thank you very much
Jan VerveckenYes. There was an internal policy on the limitation of the redirects that we reversed at the last minute before the launch. I am extremely pleased with the results.
Sonya
-
You attempt to add a word at the end of a link tag to the site level
I try to add a word before closing qoute in all links to the site level. Any way to do it without each link on all pages separately?
I tested on a single page, so I'm confident, that it will do what you want, but before you continue, you must make a backup of your site in case something goes wrong.
- Open the find and Replace dialog box (Edit menu or Ctrl + F / Cmd + F).
- The value "search in", "current Document".
- The value of "seeking to"Source Code".
- In the 'Search' field, add the following regular expression:
(
- In the field "Replace" add the following line (replace "NewText" with the text you want to add to each link):
$1new_text$2
- Select the checkbox "use regular expression.
- Test that it works by clicking on find followed next to replace.
- If you are happy that it works as expected, change ' search in ' to "Entire current Local Site" and click "replace all".
Dreamweaver warns you that you cannot undo the changes in pages that are not currently open. If you are satisfied, click OK, and the change will be at all the links.
-
How to set up a profile on the SITE level option?
To set option 'APPS_AUTH_AGENT' profile at the SITE level, what are the steps to do it? Thank you.PL see Chapter 10 of the Maitenance SysAdmin Guide - http://download.oracle.com/docs/cd/B53825_08/current/acrobat/121samg.pdf
HTH
Srini
Maybe you are looking for
-
How can I fix a display problem that appears only on the FireFox browser with my Web site?
The issue resulted in the attached screenshot is located at http://www.onhold123.com/on_hold_voices.htm. You will see that the dividing line runs in the background.
-
Qosmio F750 - how to disable the user locking after the closure of the laptop?
Hello I have a Qosmio laptop, F750 and I would keep it active after the closing of the screen keyboard. At the time you close the screen that the user is locked and my remote via WiFi connection does not recognize the laptop is ON more. I use iTunes
-
Equium A60 PSA67E - display driver problem - atidvg error
I just bought this laptop second hand. Need an operating system does all that XP pro sp. running soft bar I get an atidvg error.It changes the screen resolution of 600 by 400 and told that I need to restart. Said then the system has recovered from a
-
Bootcamp partition no longer work after resizing HD
I know this question has been asked before, but the analysis of questions seems different so new thread. I am running Mac OS 10.10.5 and 10 Windows on my Macbook Pro 13 (2012). Both the BONES have been working well, but it was difficult to share data
-
T60 unknown device, PCI Device, SM Bus
I just did a fresh XP on my T60 facility and I have 3 devices that are not the installer, even if I installed the 1 chipset driver. They are unknown device and SM Bus PCI device. My # is 200755U product. Can anyone help?