Telepresence EX60 with CUCM 8.5 - How to integrate?
Good morning people,
I'm building a lab with 8.5 CUCM and presence Server 8.5
I'll install the Cisco TelePresence EX60, and I wonder how I do integration with CUCM.
Need to install the additional server? You simply add a SIP device in CUCM?
Can someone help me?
Thank you
Bruno
Hello.
You must have CUCM 8.6 in order to utlize the full potential of the CUCM / integration EX60. You save the unit directly to the CUCM.
I recommend you take a look at this guide, after that you did with your laboratory update.
I have attached a screenshot showing how it should look like the description of the device.
Thank you
Marius
Tags: Cisco Support
Similar Questions
-
With the help of CTS EX60 without CUCM
Hello
I want to test the solution of telepresence CTS EX60 without registering to CUCM or other platform.
Is there a way to attribe him a private IP address and do NAT to test if it works or not?
I have a CTSMX200 registered to CUCM, and I want to use it to test (if possible) the EX60.
Any help?
--
Concerning
Edson VumaHi Edson,
You will have a private as 192.168.2.X behind a NAT router address or the XDSL modem. You have to install on H323 settings on the NAT mode: on and you have to write down the public IP address of the router or ADSL modem.
You have the Setup ' allocation of port: static "and then on the RTP port range settings, you can see the range of TCP/UDP ports.
It has latest configuration on the router or modem. You have Setup port address translation for the internal IP address of the EX60 with this RTP port because if you receive an internet video appeal H323 form which the public IP address, the router/modem need to know which local IP address must redirect this parcel.
The summary of port rules:
192.168.2.x tcp 1720 call signalline
192.168.2.x tcp/udp (your RTP port range)
If you do the same configuration on the two EX60, they can call each other and other VC systems over the internet and they can receive calls from other VC systems.
Best regards...
-
Integration of the Cisco Telepresence SX20 with Cisco Telepresence EX60
Hi all
I have a question, I have the following device:
-SX20 together
-EX60 with touchscreen controller
Do I know if the EX60 can be deployed in an environment SX20? as each of them as functions of call I don't know if it will be in conflict or not because I have little knowledge about the voice and video. If the device can be integrated, can I request a deployment guide, the configuration guide on these? Thank you very much!
If your devices are not connected to any call (VCS or CUCM) control, search for SX20 autonomous in the forums - there are many threads that describe what you need to configure the settings. Do the same configuration on the SX and exodus once this is done, you should be able to call the IP address of one of the other.
Wayne
--
Remember the frequency responses and mark your question as answered as appropriate. -
Edge router with CUCM/Tel Telepresence SX10 Server Mirotik / Tel conductor
Hello
I have a client with 15 sites connecting with Mikrotik router-Board of Directors.
I have to questions of implementation, in this network, a video-conferencing solution with:
15 Telepresence SX10, one for each sites
CUCM
Cisco Telepresence Server
Conductor of Cisco Telepresence
The Cucm, Serveer telepresence and the conductor will be installed on the main site.
Thank you
Yes, I also prefer this option if your go direction CUCM because he has already included as an option for CUCM licenses (multiparty license of Cisco) and lower costs.
Kind regards
Acevirgil
-
SX 20 with CUCM 8.6.1
Hello
I need to record 20 peripheral SX with CUCM 8.6.1, but SX 20 is not available in the list of devices!
How can I register it?
Regds
$
Hello
CDP file will be used for the endpoint SX20 push updates of software and the package devce for the CUCM, where it must be installed separately.
as mentioned in the document provided by Vivek:
Installation instructions
Note: Cisco recommends that you apply this device for a package
maintenance window.
Note: Packages of devices are installed on the active partition and cannot be
uninstalled;
Cisco recommends that you take a backup DRS prior to installation.
For more information on how to do a proper backup, see the Recovery Guide disaster for each version of Cisco Unified Communications Manager.
Procedure
Note: Apply this package of device to all of your Cisco Unified Communications
Manager servers, starting with the publication server and the TFTP server.
Note:
When you apply a device Package to activate the new device support, a broad cluster restart is necessary for these devices to record successfully.
A
Cluster - wide restart is not required when you apply a Package of device for the update of the existing firmware/media. Cisco Unified Communications Manager 8.6, you perform all software installations and upgrades by using the software update menu options. The system can load and process only the software that Cisco has approved. You may not install or use third party or Windows - software applications that you used a previous version of Cisco Unified Communications Manager.
1 from your web browser, go to the web page of Cisco Unified Communications Administration of the operating system.
2. in the menu of the software upgrades, select Install/Upgrade.
3. fill in the appropriate values in the section where the software and click Next.
4. in the available software drop-down list box, select the device package file
Click next
5. check that the MD5 has the correct value. Click Next.
6. in the warning box, verify that you have selected the right firmware and
then click on install.
7. check that you have received a message of success.
Note:
If you restart the cluster, skip step 8.
8. stop and restart the TFTP server.
9 reset the devices concerned to upgrade the devices to the new load.
Hope that helps
Concerning
KR Ravi
-
Hello
the customer wants to buy SX20 and Ex90, and he needs information at my side, Questions:
-Did he need a VCS? or CUCM is enogh for whom?
-What is the version CUCM is supported for SX20, EX90?
-How add these endpoints to CUCM?
-regarding bandwidth, which is good the bandwitdth to make audio and video calls is very clear and quality? up to 6 Mbps?
-What is the version for SX20 EX90 must be suppoeted with CUCM or VCS?
Please, your answers are very important to me
Thank you
Hi Lkayyali,
Please find the BW resolutions depending on requirements.
profiles of optimal definition for system supporting 1080 p
w288p30 w448p30 w576p30 720 p 1080 p 30 p 30
256kbit/s normal 512kbit/s 768kbit/s 1152kbit/s 2560kbit.s
average of 128 Kbps 384kbit/s 512kbit/s 1152 kbit/s 1920kbit/s
128 Kbps high 256kbit/s 512kbit/s 768kbit/s 1472kbit/s
profiles of optimal definition for system supporting 720 p 60
w144p60 w288p60 w448p60 w576p60 720 p 60
Normal 128kbit/s 512kbit/s 1152kbit/s 1452kbit/s 2240kbit.s
average of 128 Kbps 384kbit/s 768kbit/s 1152 kbit/s 1920kbit/s
128 Kbps high 256kbit/s 512kbit/s 768kbit/s 1152kbit/s
Please feel free to rate this answer in case it is useful
-
3241 GW ISDN with CUCM 10.5 or VCS
Hi all
What is the best practice to deploy ISDN GW 3241.
It connects with CUCM or VCS control?
How to connect it with CUCM or VCS?
Kind regards
There are some basic steps in the Quick Start Guide and there is more information on the different ways to configure it in this thread: https://supportforums.cisco.com/discussion/11580051/isdn-gw-3241-admin-config-guide
Wayne
--
Remember the frequency responses and mark your question as answered as appropriate. -
320 TS Cisco with CUCM integration
Dear experts,
Is there a way we can integrate the TS with CUCM 320 without any conductor.
Means of SIP trunk or as conference bridge.
BR
Hi Muhammad
Telepresence on 310/320 Media Server and Cisco TelePresence Server on a Virtual Machine do not support managed locally; mode on these platforms, the telepresence server must be managed by a system as a conductor of Cisco TelePresence
Conductor for the unique conference bridge is free.
BR Oleksandr
-
can't make an external call with CuCM and H323 gateway
Hi experts, I have a problem with CuCM and h323 Gateway. I use a 2811 router to make a gateway H323, CuCM server and Switch layer 2 build a VoIP LAB, this my network:
and my router configuration:
Current configuration: 2335 bytes
!
version 12.4
horodateurs service debug datetime msec
Log service timestamps datetime msec
no password encryption service
!
router host name
!
boot-start-marker
boot-end-marker
!
forest-meter operation of syslog messages
!
No aaa new-model
!
!
!
dot11 syslog
IP source-route
!
!
IP cef
DHCP excluded-address 192.168.1.1 IP 192.168.1.10
!
IP VOICE dhcp pool
network 192.168.1.0 255.255.255.0
option 150 ip 192.168.1.2
default router 192.168.1.1
!
!
No ipv6 cef
!
Authenticated MultiLink bundle-name Panel
!
!
voip phone service
h323 connections allow h323
allow connections h323 to SIP
allow connections sip h323
allow sip to sip connections
service additional h450.12
Fax protocol cisco
!
!
!
vocal h323 class 1
H225 timeout tcp establish 3
!
!
!
translation of the voice-rule 1
rule 1 / ^ 9.
!
!
voice translation-profile PSTN
translate 1 called
!
!
voice-card 0
!
!
application
Service flash aa1: its - cisco.2.0.2.0.tcl
paramspace English language en
paramspace English index 1
Param aa-driver 0839959204
paramspace location English flash:
prefix English paramspace
!
!
!
Archives
The config log
hidekeys
!
!
interface FastEthernet0/0
IP 192.168.1.1 255.255.255.0
automatic duplex
automatic speed
H323-gateway voip interface
port of link voip H323-gateway 192.168.1.1
!
interface FastEthernet0/1
no ip address
Shutdown
automatic duplex
automatic speed
!
IP forward-Protocol ND
no ip address of the http server
no ip http secure server
!
!
!
control plan
!
!
!
voice-port 0/0/0
cover of the echo - cancel 32
connection ERA opx 3100
Description 08395959204
activation of the caller ID
!
voice-port 1/0/0
!
voice-port 0/0/2
!
voice-port 0/0/3
!
!
!
1010 Dial-peer voice pots
Service aa1
incoming called number 08395959204
direct line to inside
port 0/0/0
!
voice pots Dial-peer 2020
PSTN description
translation-profile outgoing PSTN
destination-model 9 t
Setup progress_ind allow 3
progress_ind enable progress 8
port 0/0/0
Forward-digits all the
!
Dial-peer voice 10 voip
destination-model 1...
Setup progress_ind allow 3
progress_ind enable progress 8
h323 voice-class 1
session target ipv4:192.168.1.2
DTMF-relay h245 alphanumeric
Codec g711ulaw
No vad
!
!
!
!
Line con 0
line to 0
line vty 0 4
Cisco password
opening of session
!
Scheduler allocate 20000 1000
end
I have configured the gateway h323 and attach files to router parttern on follow CUCM
What is the problem and how to solve?
Thanks for all the help.
Your DP pointing CUCM is wrong, or your ÉRA OPX, depending on what you need.
voice-port 0/0/0
cover of the echo - cancel 32
connection ERA opx 3100
Description 08395959204
activation of the caller ID
Dial-peer voice 10 voip
destination-model 1...
Setup progress_ind allow 3
progress_ind enable progress 8
h323 voice-class 1
session target ipv4:192.168.1.2
DTMF-relay h245 alphanumeric
Codec g711ulaw
No vad
Your DP is waiting for 1... and you send 3100, they must match.
You might need to change the significantt numbers and entering CSS, but only you can know
For outgoing, you are throwing 9 predot, but again, expect it in your RFP, again, change as you need.
voice pots Dial-peer 2020
PSTN description
translation-profile outgoing PSTN
destination-model 9 t
Setup progress_ind allow 3
progress_ind enable progress 8
port 0/0/0
Forward-digits all the
You cannot transfer the numbers all send you also 9 for each call
Change your configuration you want / need.
HTH
Java
If it helps, please note
-
Hello
There is a lot of confusion on Express C/E & VCS C/E, if anyone can confirm my following queries:
With VCS VCS & Express control every endpoint to register with VCS control (no participation required CUCM or VCS control can't integrate with CUCM)?
With Highway Core & edge that every endpoint is record in CUCM & CUCM will record Expressway Core?
For calls B2B & movi Jabber, that we must have Expressway Center/periphery, VCS control/Express IS NOT support jabber movi & called B2B?
Software Express C/E & VCS C/E are the same, but the licenses are different?
Our clients have obtained
1 x control VCS licensed
1 x Express VCS under license
1 x ISDN gateway,
1 x TP driver
1 x TP management suit.
Kind regards
Francisco
With VCS VCS & Express control every endpoint to register with VCS control (no participation required CUCM or VCS control can't integrate with CUCM)?
Yes, no CUCM is required, endpoints can also enroll in the VCS-E or it could register SIP to VCS - C proxy endpoints. A parallel installation of VCS CUCM with a trunk should also work with todays versions.
The VCS will be only support standards basis of endpoints SIP and H323, its main purpose
a for video settings. You won't be able to use it to register, provision or use of Cisco IP phones with it.
With Highway Core & edge that every endpoint is record in CUCM & CUCM will record Expressway Core?
See the C & E highway as a single unit to the external communication. The registrations are transferred by proxy
CUCM outside.
But that also means, you can't register 3 party at the highway and even end points
Cisco endpoints must support the installation of the fast track C & E.
The highway also runs things like XMPP for Jabber.
For calls B2B & movi Jabber, that we must have Expressway Center/periphery, VCS control/Express IS NOT support jabber movi & called B2B?
The C & E Highway can also manipulate calls business2business or another sip trunks / h323, but this infrastructure requires the media license.
B2B calls also works very well with the installation of VCS.
If you are talking about how to provide Jabber accounts and video Jabber:
There are video Jabber (which is implemented by TMS and VCS) and Jabber (i.e. led CUCM) there.
If you are talking about outside calls that he can just be regarded as regular b2b external calls.
then they be it work with VCS or motorways on the site of the end.
Software Express C/E & VCS C/E are the same, but the licenses are different?
It is correct. Licensing Expressway is more attractive for users CUCM, but you already have
have SPRDD in place that should work in all cases well.
With CUCM, you get licenses Expressway in any case. So according to the type of use, you.
B2B, internal calls... you can add a configuration of fast track to Jabber and the stuff of office home and
use the VCs to B2B and part 3 records.
-
Range of Ports RTP endpoints TC changed after registering with CUCM
Hello community,
We have SX80 endpoints running TC7.3.2 and registered at CUCM 11.
By default the TC ports rank 2326-2487 UDP RTP endpoints. After registering with CUCM, the range of ports have been changed to 16384 to 32766. In my view, WHAT CUCM change the codec settings.
Based on the http://www.cisco.com/c/dam/en/us/td/docs/telepresence/endpoint/codec-c-series/tc7/administration-guide/administering-endpoints-running-tc72-on-ucm1051.pdf guide I couldn't see any setting to do with RTP ports.
This is a problem for us, because on the firewall rules, we have configured and fixed ports for points endpoints use the default go 2326-2487 UDP. Because these endpoints and video infrastructure (servers of telepresence, TCS, VCS) are on different networks separated by firewalls. At present, when recording and join the conference bridge there are no media because ports have been changed. When I change the default port range, there is no problem with the media. I can record and call to the conference bridge hosted by a TP server successfully. And if I hit the button refresh on the web GUI of the codec, 16384 to 32766 changes the settings.
Y at - it a setting that I could check on the side of CUCM?
Thanks in advance.
«By default the endpoints ports rank 2326-2487 UDP RTP TC.» After registering with CUCM, the range of ports have been changed to 16384 to 32766. "I believe THAT CUCM change the codec settings".
Yes, it's true. Once your video endpoint is configured and registered on the CUCM, the CUCM will be more than just the default settings of your endpoint. It depends on the SIP profile has been used and applied for your endpoint. You need to check that the configuration of the SIP profile of the CUCM applied for your endpoint. In your case if it's SX80, check the SIP for SX80 profile and change the start and stop media ports. It comes to the RTP port range.
In your case:
Port of bootable media: 2326
Stop Media Port: 2487
Kind regards
Acevirgil
-
I have iOS 10 and I am still unable to make messages with animation effects. How can I solve this problem?
Without knowing what is happening when you try, it is difficult to recommend troubleshooting. However, one of the first steps is to ensure that you don't have to reduce the Motion activated in accessibility.
-
Until the latest update when the url I wanted in the address bar of AutoComplete has been selected, it "accompanies" no more further by clicking on. I must now click the refresh arrow. It won't work even with the return. How can I operate the old way easier?
You can disable this extension in tools > Modules > Extensions and close and restart Firefox normally.
-
I've been using Sync plugin with my installation of Firefox 3.6. Now, I move to a new laptop with Firefox 4. How to import Firefox 3.6 of Firefox 4 synchronized entries?
Hello!
You have 2 options. If you decide to use Firefox Sync to do, follow the instructions described here: How can I set up Sync on my computer?
The other option is to do it manually. To do this, you must migrate the profile. Follow this procedure: back up and restore the information contained in the profiles of Firefox
-
my wifi password has been changed and now I want to get back in touch with the new password HOW
my wifi password has been changed and now I want to get back in touch with the new password HOW
Hey gerritfrompretoria,
If you are not prompted to use the new password to your Wi - Fi network when trying to connect, you may have to remove the network on your system. This can be done by the following steps.
- Open system preferences in the Apple menu
- Choose the network
- Select a Wi - Fi connection on the left
- Click Advanced... in the bottom right
- Choose your network from the list of preferred networks
- Click on the '-' at the bottom of the list
- Click OK
- Click on apply
Once removed try to connect to your Wi - Fi network normally and you will be prompted for the password.
Sincerely
Maybe you are looking for
-
I want to have my favorites in the left pane of the default desktop, when I connect in firefox, as before. the solution proposed in the firefox help page "What happened to the bookmarks toolbar?", i.e. to check "bookmarks toolbar" in the drop-down di
-
Satellite P - display on screen is sideways
Hi guys Hoping for more help inside the problem my 1.5 years caused tonight. When left alone for a second with open computer laptop! She managed to put the screen on the screen on the side:) And I'm not the most technical people so any advice highly
-
Hi I'm looking for a Westward 3 game on my Win Xp, but I can't. I look in DXdiag to see what is the problem and my computer hangs over the entrance. When I ran a debugger Windows on it, the listed Debugger entry broke when he tries to load my IE brow
-
When I open a file today, he said that it was empty, but I did not remove the content. I searched the trash, but it's not here. Probably the name of the file would have been as well as content if it had been deleted? I did a search, but he finds ever
-
Do not let me install any apk file
I updated my phone to pacifier, but she will not let me install any apk. The install tab does not work when I proceed to the installation!