VCS Express with CUCM 10

Similar Questions

• Reuse an existing one (currently registered for VCS) C20 with CUCM 8.6.2

  Hello friends...

  I have existing C20 which is registed to the VCS control running Software version: TC6.0.0.876266.

  Now, I thought of trying to save this to my 8.6.2 CUCM end point. I know that there is a different firmware (file Release TC5.1.3 - COP CUCM) who should be responsible on this endpoint before it can register.

  I looked for Cisco docos but they all assume that the Endepoint is already running a friendly of CUCM (file COP) endpoint. No cover that I could find the steps on how to get the file of the Conference of the PARTIES on the endpoint.

  Unless he can can be loaded via the CUCM by registering to the CUCM? But my question, it'll still join CUCM if he does not run the

  CUCM friendly (COP file) on the endpoint.

  Any thoughts on this will be appreciated.

  Kind regards

  Hello

  You're poorly understand the concept. C20 and an other TC end points do not have a special firmware to run on CUCM. The COP file that you install on CUCM is just a package to contain the common endpoint upgrade file, the same file that you can download and install manually in your endpoint.

  You can then go ahead and enter them on CUCM 8.6.2 is running the same version you, TC 6.0.0.

  This document contains all the instructions you need:

  http://www.Cisco.com/en/us/docs/Telepresence/endpoint/codec-c-series/TC5/administration_guide/cts_endpoint_administration_ucm86_quick_start_guide_tc50.PDF

  Concerning

  Paulo Souza

  My answer was helpful? Please note the useful answers and do not forget to mark questions resolved as "responded."

• 3241 GW ISDN with CUCM 10.5 or VCS

  Hi all

  What is the best practice to deploy ISDN GW 3241.

  It connects with CUCM or VCS control?

  How to connect it with CUCM or VCS?

  Kind regards

  There are some basic steps in the Quick Start Guide and there is more information on the different ways to configure it in this thread: https://supportforums.cisco.com/discussion/11580051/isdn-gw-3241-admin-config-guide

  Wayne
  --
  Remember the frequency responses and mark your question as answered as appropriate.

• SX20, EX90 with CUCM

  Hello

  the customer wants to buy SX20 and Ex90, and he needs information at my side, Questions:

  -Did he need a VCS? or CUCM is enogh for whom?

  -What is the version CUCM is supported for SX20, EX90?

  -How add these endpoints to CUCM?

  -regarding bandwidth, which is good the bandwitdth to make audio and video calls is very clear and quality? up to 6 Mbps?

  -What is the version for SX20 EX90 must be suppoeted with CUCM or VCS?

  Please, your answers are very important to me

  Thank you

  Hi Lkayyali,

  Please find the BW resolutions depending on requirements.

  profiles of optimal definition for system supporting 1080 p

  w288p30 w448p30 w576p30 720 p 1080 p 30 p 30

  256kbit/s normal 512kbit/s 768kbit/s 1152kbit/s 2560kbit.s

  average of 128 Kbps 384kbit/s 512kbit/s 1152 kbit/s 1920kbit/s

  128 Kbps high 256kbit/s 512kbit/s 768kbit/s 1472kbit/s

  profiles of optimal definition for system supporting 720 p 60

  w144p60 w288p60 w448p60 w576p60 720 p 60

  Normal 128kbit/s 512kbit/s 1152kbit/s 1452kbit/s 2240kbit.s

  average of 128 Kbps 384kbit/s 768kbit/s 1152 kbit/s 1920kbit/s

  128 Kbps high 256kbit/s 512kbit/s 768kbit/s 1152kbit/s

  Please feel free to rate this answer in case it is useful

• VCS-Express and the integration of control VCS

  Hello

  I have the following question on the integration between VCS and VCS Express behind NAT devices.

  Control of VCS in the configuration of the area customer I will use the (Real) Global IP address location > Peer Address or I have to use the private IP address.

  Thank you

  Hello

  It depends on the interface how you have connected on the highway. So if you have two connected interfaces then the internal one is configured with a private address, and that you would use on the control to send traffic to. But to your question, I assume you have a connected only interface so you can use the public ip address for sent traffic of venture capital control.

  Ask if you need more information.

  Best regards / / Andrey

• Range of Ports RTP endpoints TC changed after registering with CUCM

  Hello community,

  We have SX80 endpoints running TC7.3.2 and registered at CUCM 11.

  By default the TC ports rank 2326-2487 UDP RTP endpoints. After registering with CUCM, the range of ports have been changed to 16384 to 32766. In my view, WHAT CUCM change the codec settings.

  rtp_ports.PNG

  

  Based on the http://www.cisco.com/c/dam/en/us/td/docs/telepresence/endpoint/codec-c-series/tc7/administration-guide/administering-endpoints-running-tc72-on-ucm1051.pdf guide I couldn't see any setting to do with RTP ports.

  This is a problem for us, because on the firewall rules, we have configured and fixed ports for points endpoints use the default go 2326-2487 UDP. Because these endpoints and video infrastructure (servers of telepresence, TCS, VCS) are on different networks separated by firewalls. At present, when recording and join the conference bridge there are no media because ports have been changed. When I change the default port range, there is no problem with the media. I can record and call to the conference bridge hosted by a TP server successfully. And if I hit the button refresh on the web GUI of the codec, 16384 to 32766 changes the settings.

  Y at - it a setting that I could check on the side of CUCM?

  Thanks in advance.

  «By default the endpoints ports rank 2326-2487 UDP RTP TC.» After registering with CUCM, the range of ports have been changed to 16384 to 32766. "I believe THAT CUCM change the codec settings".

  Yes, it's true. Once your video endpoint is configured and registered on the CUCM, the CUCM will be more than just the default settings of your endpoint. It depends on the SIP profile has been used and applied for your endpoint. You need to check that the configuration of the SIP profile of the CUCM applied for your endpoint. In your case if it's SX80, check the SIP for SX80 profile and change the start and stop media ports. It comes to the RTP port range.

  In your case:

  Port of bootable media: 2326

  Stop Media Port: 2487

  rtp_cucm.PNG

  

  Kind regards

  Acevirgil

• I replace my airport express with the new model. Flashing orange. It works, but cannot configure security. Tried to reset via the reset button.

  I replace my airport express with the new model. Flashing orange. It works, but cannot configure security. Tried to reset via the reset button. Tried unplugging and tried unplugging the modem. I would like to fix.

  Modem... doing and... model number you have?

  What operating system do you use on your Mac, or you are using an iPhone or iPad set things up... or a PC?

• Connection to the server would not check when you configure Outlook Express with Charter Web Mail

  Hello! I call on my Outlook Express is installed on my Windows XP Professional. I need assistance with the configuration of Outlook Express with my Charter Web Mail. Charter, I called and they helped me with the setup but I'm stuck on the last part and it gave me an error on the server. The "connection to the server don't check not" and the Charter was not able to help me through, and they said it's a Microsoft Issue. I need some help here. Please help me! Thank you!

  See here: http://www.myaccount.charter.com/customers/support.aspx?supportarticleid=1241

  There are step by step instructions.

  Steve

• I'm tring to disable windows live mail, but I need windows live for my xbox, I use outlook express but now WLM keeps poping up. IWant outlook express with yahoo on windows xp email. What can I do?

  I am trying to disable windows live mail, but I need windows live for my xbox, I use outlook express but now WLM keeps poping up. IWant outlook express with yahoo on windows xp email. What can I do?

  Try going to tools | Options in OE and set it as default value for it.  Also in Internet Explorer go to tools | Internet Options | Programs and set as default OE it as well, or click the reset web settings button, if it is present.

  Steve

• Unity connection 8.6 Migration to 11 with CUCM 8.0

  Due to the right I'm going to intend a Migration of 8.6 connection unit to 11.0 of connection of the unit before I can improve CUCM. I am sure that the answer is Yes, but would there be problems running 11.0 of connection of the unit with CUCM 8.0.

  Nothing fancy on the face of connection of the unit, no unified messaging ect.

  New UC 11.0 should just registered the EPSC ports?

  Thank you

  Dan

  Looks like you need at least version 8.5 for the SCCP and SIP integration CUCM to be supported. Check the compatibility of connection of the unit guide below.

  http://www.Cisco.com/c/en/us/TD/docs/voice_ip_comm/connection/compatibil...

  Combinations for Cisco and unity connection Unified Communications Manager of the supported Version

  Table 22 Version combinations of supported for the connection of the unit and Cisco Unified Communications Manager

  Cisco Unity Connection	Cisco Unified Communications Manager
  8.5 and later	11.5 (1), 11.0 (1), 10.5 (2), 10.5 (1), 10.0 (1) 9.1 2, 9.1 (1), 9.0 (1), 8.6 (2), 8.6 (1), 8.5 (1)

  SIP: http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/connection/compatibil...

  -Terry

  Please note all useful posts

• SX 20 with CUCM 8.6.1

  Hello

  I need to record 20 peripheral SX with CUCM 8.6.1, but SX 20 is not available in the list of devices!

  How can I register it?

  Regds

  $

  Hello

  CDP file will be used for the endpoint SX20 push updates of software and the package devce for the CUCM, where it must be installed separately.

  as mentioned in the document provided by Vivek:

  Installation instructions

  Note: Cisco recommends that you apply this device for a package

  maintenance window.

  Note: Packages of devices are installed on the active partition and cannot be

  uninstalled;

  Cisco recommends that you take a backup DRS prior to installation.

  For more information on how to do a proper backup, see the Recovery Guide disaster for each version of Cisco Unified Communications Manager.

  Procedure

  Note: Apply this package of device to all of your Cisco Unified Communications

  Manager servers, starting with the publication server and the TFTP server.

  Note:

  When you apply a device Package to activate the new device support, a broad cluster restart is necessary for these devices to record successfully.

  A

  Cluster - wide restart is not required when you apply a Package of device for the update of the existing firmware/media. Cisco Unified Communications Manager 8.6, you perform all software installations and upgrades by using the software update menu options. The system can load and process only the software that Cisco has approved. You may not install or use third party or Windows - software applications that you used a previous version of Cisco Unified Communications Manager.

  1 from your web browser, go to the web page of Cisco Unified Communications Administration of the operating system.

  2. in the menu of the software upgrades, select Install/Upgrade.

  3. fill in the appropriate values in the section where the software and click Next.

  4. in the available software drop-down list box, select the device package file

  Click next

  5. check that the MD5 has the correct value. Click Next.

  6. in the warning box, verify that you have selected the right firmware and

  then click on install.

  7. check that you have received a message of success.

  Note:

  If you restart the cluster, skip step 8.

  8. stop and restart the TFTP server.

  9 reset the devices concerned to upgrade the devices to the new load.

  Hope that helps

  Concerning

  KR Ravi

• MGCP FXO does not register with CUCM on VG204XM

  I have a VG204XM running MGCP with CUCM 10.5. When the port is changed and reset him CUCM config push down to the VG204XM there is an error (it is identical to the Bug CSCtr78616 reported on a router 28xx in 2011)

  In the newspapers, I see that, once the router receives the config it tried to configure AALN/S0 / / 0 (voice-port 0/0)
  However, for some reason, it seems that the router is to convert the port to a 65535 instead of 0

  "cmapp_xml_get_interface_info: slot = 0 vic = 65535 port = 0".

  Since the port above does not exist on the router the survey attempt a mistake.

  Mar 27 18:07:59.278: % SYS-5-CONFIG_I: configured from console by console
  Mar 27 18:07:59.278: cmapp_xml_get_interface_info:
  18:07:59.278 Mar 27: =.
  Mar 27 18:07:59.278: cmapp_xml_get_interface_info: slot = 0 vic = 65535 port = 0
  18:07:59.278 Mar 27: Interface_name: AALN/S0/0
  Mar 27 18:07:59.278: controller:
  18:07:59.278 Mar 27: addr: 65535/0/0
  Mar 27 18:07:59.278: interface:
  Mar 27 18:07:59.278: voice_port: voice-port 65535/0/0
  Mar 27 18:07:59.278: dial_peer: voice dial-peer 9990655350
  Mar 27 18:07:59.278: dial_peer_port: 65535/0/0
  Mar 27 18:07:59.278:
  Mar 27 18:07:59.278: cmapp_xml_configure_router: verification of the Deleted interfaces
  Mar 27 18:07:59.278: cmapp_xml_get_intf: looking for a vdb [65535/0/0]
  Mar 27 18:07:59.278: cmapp_xml_configure_router: analog ports are ready
  Mar 27 18:07:59.278: cmapp_xml_find_corr_intf_cfg:
  Mar 27 18:07:59.278: cmapp_xml_find_corr_intf_cfg: old_cfg is NULL
  Mar 27 18:07:59.282: cmapp_xml_intf_cfg_changed:
  Mar 27 18:07:59.282: old intf configuration is null
  Mar 27 18:07:59.282: cmapp_xml_cfg_analog_intf:
  Mar 27 18:07:59.282: cmapp_mgcp_get_card_type_for_analog_intf: looking for a vdb [65535/0/0]
  Mar 27 18:07:59.294: cmapp_xml_cfg_router_intf: intf configuration: [voice-port 65535/0/0]
  Mar 27 18:07:59.294: cmapp_xml_cfg_router_intf: configuration [echo - cancel enable]
  Mar 27 18:07:59.298: % SYS-5-CONFIG_I: configured from console by console
  Mar 27 18:07:59.298: cmapp_xml_cfg_router_intf: 395 line router configuration error
  Mar 27 18:07:59.298: cmapp_xml_send_msg_to_callmgr: CMBH_MSG_CFG_ERR of sending
  Mar 27 18:07:59.298: * info ERROR: the router configuration failed: voice-port 65535/0/0
  echo - cancel enable
  end

  I have a VG224 gateways running with MGCP CUCM 10,5 and no error

  Everyone knows about this problem on VG204XM?

  Hello

  Please check

  https://Tools.Cisco.com/bugsearch/bug/CSCui83022/?reffering_site=dumpcr

  Auto config MGCP fails for VG204XM
  CSCui83022
   

  Description

• Connection of the UNIT with CUCM integration

  Hello

  Can someone please advice me on the underside, I CUCM (PUB + 1 SUB) cluster and node stand-alone 1 CUC.

  need to know the best Cisco recommended configuration

  1.0 order of AXL servers (what should we put 0 - PUB or SUB)

  2.0 tftp and order serever CUCM under port, (PUB, order SUB) group settings

  Please advice

  Thank you

  Purna

  Axl Server always be PUB and SUB.
  Pub - 0
  Sub - 1

  TFTP server must first be Sub and PUB.

  Sub - 0
  Pub - 1

  This is the best way and the recommended method to configure / integration with CUCM with connecting the unit

  Sent by Cisco Support technique iPhone App

• Cisco C40 unsubscribe automatically with CUCM 8.6.2

  Hello

  I have Cisco C40 connected to CUCM 8.6.2.

  First, he is registered with CUCM and I was able to call on another phone C40.

  Then, C40 automatically BSW of CUCM and isn't recording with CUCM now.

  I added C40 via device-> phone-> Add new-> then selected Teleprecense C40

  C40 SW version is: 5.1.5.297625

  I joined C40 and CUCM screenshot. It shows not recorded, which proves C40 registerd at least once.

  I could make and receive calls with the C40 for a few minutes. Subsequently recorded automatically and now

  error message is status: failed

  Suggest pls.

  Rgds

  Rajesh

  Hi Renon,

  Please below changes made in the SIP settings:

  change SIP profile 1 Type at Cisco, since it is native enrolled and default transport for TCP

  * c xConfiguration SIP URI 1 profile: "[email protected] / * / "

  "

  * c xConfiguration SIP profile 1 DisplayName:

  * c xConfiguration SIP DefaultTransport 1 profile: TCP

  * c xConfiguration SIP profile 1 TlsVerify: Off

  * c xConfiguration SIP profile Type 1: Cisco

  * c xConfiguration SIP profile 1 outgoing: Off

  * c xConfiguration SIP profile 1 Proxy Discovery 1: manual

  * c xConfiguration SIP Proxy 1 address of profile 1: "172.31.131.10."

  * c xConfiguration SIP profile 1 Proxy Discovery 2: manual

  * c xConfiguration SIP Proxy 2 address of profile 1:

  * c xConfiguration SIP profile 1 Proxy Discovery 3: manual

  * c xConfiguration SIP Proxy 3 address profile 1:

  * c xConfiguration SIP profile 1 Proxy Discovery 4: manual

  * c xConfiguration SIP Proxy 4 address of profile 1:

  * c xConfiguration SIP profile 1 1 LoginName authentication:

  * c xConfiguration SIP profile 1 1 password:

• Telepresence EX60 with CUCM 8.5 - How to integrate?

  Good morning people,

  I'm building a lab with 8.5 CUCM and presence Server 8.5

  I'll install the Cisco TelePresence EX60, and I wonder how I do integration with CUCM.

  Need to install the additional server? You simply add a SIP device in CUCM?

  Can someone help me?

  Thank you

  Bruno

  Hello.

  You must have CUCM 8.6 in order to utlize the full potential of the CUCM / integration EX60. You save the unit directly to the CUCM.

  I recommend you take a look at this guide, after that you did with your laboratory update.

  http://www.Cisco.com/en/us/docs/Telepresence/endpoint/codec-c-series/TC5/administration_guide/cts_endpoint_administration_ucm86_quick_start_guide_tc50.PDF

  I have attached a screenshot showing how it should look like the description of the device.

  Thank you

  Marius