That treats the assignment do VLAN authorization Cisco ISE?

Hello

When I create an authorization policy in Cisco ISE, under common tasks, it is the assignment of VLANS. What makes that? Is it puts the user on this VLAN?

Thank you.

Yes, this will overwrite the VLAN configured on the switch port/SSID or wireless. For example, all ports can be configured to be part of VLAN 10, but you want users to finances in VLAN 20. You can use the profile of EHT permission to do exactly this.

Thank you for evaluating useful messages!

Tags: Cisco Security

Similar Questions

Authentication of 802. 1 X with the assignment problem VLAN.

Hello

I intend to implement the authentication of 802. 1 X with assignment of VLANS on our network and assign different VLAN on the switch (Cat2960) of access according to the terminals (for example, VLAN10 for VLAN40 for PC, VLA30 for STB IPTV, VLAN20 for voice, WLAN) after a successful authentication.

Is the topology of the network (backbone L3 Switch: Cat6K) <----->(L2 access switch: Cat2960) <-------->(L2 access switch: Cat2960) <-->WLAN, voice, IPTV, PC. (Please refer to the file for the detailed topology rasthaus)

I have to respect (switch L2) <-->(switch L2) topology due to wiring problem.

My question is below.

1. to take account of different VLAN of terminals, the only way is in trunk on both L2 switches port. is this possible?

As far as I know, cannot enable 802. 1 X on a trunk port. is it good?

2. If this is true, is there a solution?

Thank you for your help. :-)

You will not run 802. 1 x on the junction between switch ports, but rather on the ports that connect devices to end-users.

The band multiple @domaine used in user name on the integration of commercials with Cisco ISE?

Hello

How to remove multiple domain suffixes through ISE with AD user name used as an external identity Source. Username is used in [email protected] / * / format.

Cisco ISE 1.2 patch introduced 4 Strip prefix or suffix @domaine Kingdom of the username through ISE with AD used as external identity Source. But the documentation is not updated for this feature. I am able to band 1 domain successfully suffix but following conditions listed in the list of suffixes fails to get stripped.

Any thoughts on the same.

Thanks Kumar

In the ISE under Administration > identity management > external identity Sources

Choose the Active Directory on the left, select your ad server and Advanced settings

Under identity band of suffix, make sure prefixes band below: is selected (I know, it says prefix).

In the list of Suffixes box, enter your list of domain suffixes to undress. The separator character is a comma (,).

If this does not solve your problem, then I fear that a call to TAC may be in order.

UPDATE *.

Spaces are significant characters. The registration of domains, so as such:

@domain.com, @domain.local, @testdomain.com

END UPDATE *.

Please rate useful messages and mark this question as answered if, in fact, does that answer your question. Otherwise, feel free to post additional questions.

Charles Moreton

Post edited by: Charles Moreton

@domaine band on the integration of commercials with Cisco ISE?

Hello

How can I strip area @domaine of the user through ISE with AD name used as an external identity Source. User name is used in

[email protected] / * / format.

Thanks Kumar

This is now supported in the ISE 4 1.2 patch. recently posted in EAC:

CSCuj95908 ISE is not field stripping for external store AD

ADF Mobile: contact is created on the device that, after the user selects the button AUTHORIZE

My app allows users to quickly and easily add contacts on their IOS phone. I need help capturing the "do not ALLOW" button click.
Background:
When you add a contact to the users device phoneGap prompts the user "Allow PAP to access Contacts?". After that this alert is displayed, the user must select "Allow" or "Disallow". Of course if the user selects "Allow" my code works perfectly.
However, if the user selects "Do not allow" I'm not able to capture this selection and process accordingly.
Here's the line of code that treats the newContact for this user to the application.
Contact newContact = device.createContact (contact);
where the 'contact' has been resolved with the user data
You would offer your expert opinion on how to do it please?
Thank you very much!
Tree Strepek

The permissions for iOS in the config.xml file.

https://github.com/Apache/Cordova-plugin-contacts/BLOB/master/src/iOS/CDVContacts.h

Dynamic assignment of VLANS for MAB / ACS 5.5

Hello

Tried MAB works with ACS 5.5, and the looks part good ACS in the newspapers - the MAC address is sought, the authorization profile is correct. But on the switch, I get the following text:

* 1 mar 00:12:53: AAA/AUTHENTIC/8021 X (00000004): choose method list "by default".

* 1 mar 00:12:53: RADIUS/ENCODE (00000004): orig. component type = DOT1X

* 1 mar 00:12:53: RADIUS: AAA Attr not supported: audit-session-id [607] 24

* 1 mar 00:12:53: RADIUS: [0A8E0FDE00000002] 30 41 38 45 30 46 44 45 30 30 30 30 30 30 30 32

* 1 mar 00:12:53: RADIUS: 30 30 30 38 30 [00080 41A]

* 1 mar 00:12:53: RADIUS: AAA Attr not supported: interface [171] 20

* 1 mar 00:12:53: RADIUS: 47 69 67 61 62 69 74 45 74 68 65 72 65 74 31 [GigabitEthernet1] 6F

* 1 mar 00:12:53: RADIUS: 2F 30 [/ 0]

* 1 mar 00:12:53: RADIUS (00000004): Config NAS IP: 0.0.0.0

* 1 mar 00:12:53: RADIUS / ENCODE (00000004): acct_session_id: 4

* 1 mar 00:12:53: RADIUS (00000004): send

* 1 mar 00:12:53: RADIUS/ENCODE: best local IP 10.142.15.222 for Radius server address - 10.54.248.55

* 1 mar 00:12:53: RADIUS (00000004): send request to access the id 10.54.248.55:1645 1645/5, len 162

* 1 mar 00:12:53: RADIUS: 5th authenticator FE 17 88 64 41 1 D 09-86 EA 51 BE 78 42 B6 EB

* 1 mar 00:12:53: RADIUS: username [1] 14 "28924ad5a199".

* 1 mar 00:12:53: RADIUS: User-Password [2] 18 *.

* 1 mar 00:12:53: RADIUS: 6 Service-Type call control [6] [10]

* 1 mar 00:12:53: RADIUS: Framed-MTU [12] 6 1500

* 1 mar 00:12:53: RADIUS: Called-Station-Id [30] 19 "00-1A-A1-99-9F-82".

* 1 mar 00:12:53: RADIUS: Calling-Station-Id [31] 19 "28-92-4A-D5-A1-99".

* 1 mar 00:12:53: RADIUS: Message-Authenticato [80] 18

* 1 mar 00:12:53: RADIUS: EE F5 B8 E1 70 37 A6 3A AD 89 20 A5 A7 D0 E3 B4 [p7:]

* 1 mar 00:12:53: RADIUS: EAP-Key-Name [102] 2 *.

* 1 mar 00:12:53: RADIUS: NAS-Port-Type [61] 6 Ethernet [15]

* 1 mar 00:12:53: RADIUS: NAS-Port [5] 6 50102

* 1 mar 00:12:53: RADIUS: NAS-Port-Id [87] 22 'GigabitEthernet1/0/2 '.

* 1 mar 00:12:53: RADIUS: NAS-IP-Address [4] 6 10.142.15.222

* 1 mar 00:12:53: RADIUS (00000004): started 5 sec timeout

* 1 mar 00:12:53: RADIUS: receipt id 1645/5 10.54.248.55:1645, Access-Accept, len 106

* 1 mar 00:12:53: RADIUS: authenticator 26 B4 B9 AB 3 04 68 DA - 38 AF F6 CD 36 95 73 2 b

* 1 mar 00:12:53: RADIUS: username [1] 19 "28-92-4A-D5-A1-99".

* 1 mar 00:12:53: RADIUS: [25] of class 31

* 1 mar 00:12:53: RADIUS: 43 41 43 53 3 a 41 30 31 44 52 46 4 30 30 32 2F [CACS:A01DRFN002 /]

* 1 mar 00:12:53: RADIUS: 32 33 31 35 38 38 36 30 31 31 37 38 2F [231588601/178]

* 1 mar 00:12:53: RADIUS: Tunnel-Type [64] 01: VLAN 6 [13]

* 1 mar 00:12:53: RADIUS: Tunnel-Medium-Type [65] 6 01:ALL_802 [6]

* 1 mar 00:12:53: RADIUS: Message-Authenticato [80] 18

* 1 mar 00:12:53: RADIUS: 91 22 50 8 62 C2 F0 10 C6 OF 70 84 AF 31 6 CD [Pbp1l ""]

* 1 mar 00:12:53: RADIUS: mount-Auth-Type [81] 6 20003120

* 1 mar 00:12:53: RADIUS (00000004): receipt of id 1645/5

* 1 mar 00:12:53: RADIUS: unsupported value 20003120 to the 81 attribute

* 1 mar 00:12:53: RADIUS/DECODE: Ascend auth type; IN CASE OF FAILURE

* 1 mar 00:12:53: RADIUS/DECODE: decoder; IN CASE OF FAILURE

* 1 mar 00:12:53: RADIUS/DECODE: Ascend-Auth-Type attribute; IN CASE OF FAILURE

* 1 mar 00:12:53: RADIUS/DECODE: analysis response op decode; IN CASE OF FAILURE

* 1 mar 00:12:53: RADIUS/DECODE: analyze the answer; IN CASE OF FAILURE

* 1 mar 00:12:53: % MAB-5-FAIL: failure of authentication for the client (2892.4ad5.a199) on the Interface item in gi1/0/2 AuditSessionID 0A8E0FDE0000000200080ABF

* 1 mar 00:12:53: % AUTHMGR-7-RESULT: result of the "dead server" authentication "MAB" for the client (2892.4ad5.a199) on the Interface item in gi1/0/2 AuditSessionID 0A8E0FDE0000000200080ABF

* 1 mar 00:12:53: % AUTHMGR-5-FAIL: failed authorization for customer (2892.4ad5.a199) on the Interface item in gi1/0/2 AuditSessionID 0A8E0FDE0000000200080ABF

It recognizes the attributes 64 and 65, but the Tunnel-private-group-id, which contains the actual number of VLAN is not supported. How can I assign the vlan OK if this attribute is not taken in charge? Does not work with a string corresponding to the name VLAN on the switch either.

The version is 12.2.55SE10 3750G.

Hello

Since him debugs if I see that you are missing an attribute to make the assignment of VLANs, in your test it just to send the following items:

* 1 mar 00:12:53: RADIUS: Tunnel-Type [64] 01: VLAN 6 [13]

* 1 mar 00:12:53: RADIUS: Tunnel-Medium-Type [65] 6 01:ALL_802 [6]

But it would be appropriate to send:
- Tunnel-Type = 64 = VLAN
- Tunnel-Medium-Type = 802
- Tunnel-private-Group-ID = 253
When the "Tunnel-private-Group-ID" is the number/name of vlan to be awarded, the bellows is an example on what it would look like on the profile of the ACS:

http://www.Cisco.com/c/dam/en/us/support/docs/wireless/5500-series-wirel...

Note: Please mark as answer as appropriate

Assignment of VLANS by MAC address on a 6248

Hello

We have a mixture of 5548 and 6248 switch batteries, all updated to the latest fw, grouped on a 8024f.

We add 560 Polycom phones to our network and want to assign phones to the voice VLAN and use the internal switch on the phone to the computer workstation.

The 5548 have the handy table YES, the:

VLAN voice Yes-table add 00907 Polycom/Veritel_phone___

It works a treat and the assignment of VLANS for phone and PC works beautifully on the 5548.

However, the 6248 legacy does not have this feature.

Am I right assuming that we cannot assign addresses MAC Polycom-issued to one VLAN specific on switches 62XX as 55XX switches on? We are left with assigning simply labeled the voice VLAN? I'm afraid non-voix tag traffic for some applications will be treated badly as voice.

What is the best way to do it? Here are the General config we will stop for the 6248:

Configure
database of VLAN
VLAN 10 100

interface vlan 10
name "VoIP."
output

interface vlan 100
name 'data network '.
Routing
IP 10.1.10.1 255.255.255.0
output

Example config for a switchport with Polycom and PC phone
!
interface ethernet 1/g1
switchport mode general
switchport General pvid 100
No switchport acceptable-framework-type general tag only
VLAN allowed switchport General add 100
switchport general allowed vlan add 10 tag
switchport vlan allowed General remove 1
output
!

The 6248 uses a Broadcom firmware and the 5548 uses a Marvell firmware, that's why we see the differences in the characteristics. The 6248 has no YES table as the 5548. Here is the basic configuration of VLAN voice on the 6248.

1.

To start creating a VLAN voice, create it first VLAN database mode for VLAN.

Console # console (config) # vlan database console(config-vlan) # vlan 2 console (config - vlan) #exit console (config) #.

2.

Then, globally enable the Vlan voice.

Console (config) # vlan VoIP

3.

In the configuration of interface for the desired port mode, assign it VLAN to the port using general mode. Then, assign it VLAN voice on the port with the command vlan vlan id #.

Console (config) # interface console item in gi1/0/10 # switchport general console mode # vlan 2 voice

There is also this white page that goes over the process.

www.Dell.com/.../pwcnt_voice_VLAN_support.pdf

A workstation sends no marked traffic, and will be placed on the general mode port PVID. In this case, it seems that your PVID is VLAN 100, therefore all workstation traffic will go to this VLAN. I'm not aware of a situation where the traffic of the workstation would be confused with traffic voice and placed on the VLAN incorrect, you have a specific situation / application where you think this can happen? I can do some research on this scenario to help alleviate any concerns.

Thank you

SG300: Cant assign aw vlan 802. 1 x + freeradius

We recently got SG300-10 and try to get the assignment of vlan dynamic works via 802.1 x and freeradius. We got it so that the client connected to the SG300 would correctly auth, IE, I see this in "see the dot1x users:

MAC Auth Auth Session VLAN

Port Username Address Method Server Time

-------- ---------------- ----------------- ------ ------ -------------- ----

gi7 testuser 58:55:ca:24:19:d4 802.1X Remote 00:04:39

However, the client does not seem to be at all on the vlan correct or any vlan. If I change the port of "dot1x - radius attributes vlan static" to "dot1x - radius attributes vlan" then the customer cant auth at all (which is expected because it cannot retrieve the information of vlan).

The freeradius users file looks like this:

testuser  Cleartext-Password := "testpassword"
##Tunnel-Tag = 0,
Tunnel-Medium-Type = IEEE-802,
Tunnel-Type = VLAN,
Tunnel-Private-Group-Id = "104"

There is this whole line in the eap.conf file:

copy_request_to_tunnel = yes

Running config:

net055#show running-config

config-file-header

net055

v1.3.5.58 / R750_NIK_1_35_647_358

CLI v1.0

set system mode switch

file SSD indicator encrypted

ssd-control-start

ssd config

ssd file passphrase control unrestricted

no ssd file integrity control

ssd-control-end cb0a3fdb1f3a1af4e4430033719968c0

vlan database

default-vlan vlan 3333

exit

vlan database

vlan 1,100,104,111

exit

voice vlan oui-table add 0001e3 Siemens_AG_phone________

voice vlan oui-table add 00036b Cisco_phone_____________

voice vlan oui-table add 00096e Avaya___________________

voice vlan oui-table add 000fe2 H3C_Aolynk______________

voice vlan oui-table add 0060b9 Philips_and_NEC_AG_phone

voice vlan oui-table add 00d01e Pingtel_phone___________

voice vlan oui-table add 00e075 Polycom/Veritel_phone___

voice vlan oui-table add 00e0bb 3Com_phone______________

dot1x system-auth-control

hostname net055

line console

exec-timeout 30

exit

line ssh

exec-timeout 0

exit

encrypted radius-server host 172.16.200.57 key #REMOVED priority 10 usage dot1.x

radius-server host source-interface vlan 100

management access-list mlist2

permit ip-source 172.16.202.0 mask 255.255.255.0

permit ip-source 172.16.200.0 mask 255.255.255.0

exit

management access-class mlist2

logging buffered debugging

aaa authentication enable default enable none

aaa accounting dot1x start-stop group radius

enable password level 15 encrypted #REMOVED

no service password-recovery

no passwords complexity enable

passwords aging 0

username #REMOVED password encrypted #REMOVED privilege 15

ip ssh server

ip ssh password-auth

ip http timeout-policy 1800 https-only

no ip http server

tacacs-server timeout 10

clock timezone " " 0 minutes 0

clock source sntp

interface vlan 100

ip address 172.16.200.21 255.255.255.0

no ip address dhcp

interface vlan 104

name gen-0-Gnv-204.0

interface vlan 111

name guest-0-Gnv-10-66-61.0

dot1x guest-vlan

interface gigabitethernet1

switchport trunk allowed vlan add 100,104,111

interface gigabitethernet7

dot1x guest-vlan enable

dot1x reauthentication

dot1x radius-attributes vlan static

dot1x port-control auto

switchport mode general

switchport general allowed vlan add 104 untagged

no macro auto smartport

exit

ip default-gateway 172.16.200.1

Looks like there was a similar questions here, but it seems to have never been resolved:

https://supportforums.Cisco.com/message/3336810#3336810

Hi all

I'm working with Colin and that ends up being a problem of RADIUS. In the file eap.conf, for peap (auth phase 1).

We need to enable copy_request_to_tunnel AND use_tunneled_reply:

{PEAP

# The syringe EAP session needs a default value
# Type of EAP that is distinct from that of
# module EAP-tunneled. Inside of the
# PEAP tunnel, we recommend that you use MS-CHAPv2,
# as the default type is supported by
# Windows clients.
default_eap_type = mschapv2

# module has PEAP also of these configuration
Articles of #, which are the same as TTLS.

copy_request_to_tunnel = yes
use_tunneled_reply = yes

Subsequently, we could see the answers of the test with id user vlan posting it once by response.

See you soon!

Is possible to write the INSERT statement that fills two columns: 'word' and 'sense' of the file text with multiple lines - in each line is followed word that is the meaning?

Is possible to write the INSERT statement that fills two columns: 'word' and 'sense' of the file text with multiple lines - in each line is followed word that is the meaning?

Hello

2796614 wrote:

Is possible to write the INSERT statement that fills two columns: 'word' and 'sense' of the file text with multiple lines - in each line is followed word that is the meaning?

Of course, it is possible. According to what the text file looks like to, you can create an external table that treats the text file as if it were a table. Otherwise, you can always read the file in PL/SQL, using the utl_file package and INSERT of PL/SQL commands.

You have problems whatever you wantt? If so, your zip code and explain what the problem is.

Whenever you have any questions, please post a small example of data (CREATE TABLE and only relevant columns, INSERT statements) for all of the tables involved and the exact results you want from these data, so that people who want to help you can recreate the problem and test their ideas. In this case, also post a small sample of the text involved file.

If you ask about a DML operation, such as INSERT, then INSERT statements, you post should show what looks like the tables before the DML, and the results will be the content of the table changed after the DML.

Explain, using specific examples, how you get these results from these data.

Always say what version of Oracle you are using (for example, 11.2.0.2.0).

See the FAQ forum: Re: 2. How can I ask a question on the forums?

Cisco ISE 1.1.1 with Windows posturing

Hello

We tired for configured windows posturing here's the scenario

We saw five ise boxes 3315 with version 1.1.1 off them 2 is admin, 2 is PS and 1 MNT

and we have local Symantec and WSUS Server.

We make posturing for Windows where I have a few questions

(1) is there an integration here of the local WSUS server with Cisco ISE where Cisco ISE can automatically take all the mandatory WSUS update according to the crititcality of the WSUS server.

(2) what is advised to set up the strategy of the Posture of the posture of windows in Cisco ISE and if manually configure windows political posture using specific KB and if there is an update available on Microsoft will we be able to configure the policy for the new update.

(3) we have configured authentication dot1x in cisco ise and asked as well as on switch port where once the user must be connected to dot1x port of the switch it invites username and password dot1x and therefore, authorization policy, it gives vlan appropriate dynamics.

But what are the ways where we can restrict the machine which is rather than the assets of the company and even if the user's user name and password in short any employee aware how we can restrict the user making the machine rather than the assets of the company?

(4) can configure US policy posture for antivirus which will keep us in normal mode and at the same time, we can put posturing for windows which monioring mode which only monitor policy posture and reflected in the monitoring, log in which does not restrict the network for windows posturing

That will be great if any one can please help me to get the issues

Thank you

Pranav

What follows is under the POLICY-OF ELEMENTS of STRATEGY-POSTURE-> REQUIREMENTS > >

What follows is located under

POLICY OF-> ELEMENTS OF STRATEGY-> POSTURE->

REPAIR-> WINDOWS SERVER UPDATE SERVICES REMEDIATION ACTIONS

What follows is part POLICY-> POSTURE

These settings work ALMOST flawlessly for me by forcing her we approved on our WSUS server for our group of workstations updated (all of our laptops are members of the) which meet the criteria of severity EXPRESS (critical and Important). Now, what I've discovered in the last few days is that... MS seems a bit random in their identification of what severity level they assign to their updates. For example... I think that a service pack of the operating system would be considered IMPORTANT if not CRITICAL... however... Look at this from the identification of the server WSUS from Windows 7 Service Pack 1:

Thus, those who updates you deleted, I'd go throgh your WSUS server to identify how they are identified by gravity, then according to your needs set the parameters of the ISE accordingly to ensure that you get updates you plan.

Hope this helps everyone out there who has similar problems.

Thank you

Dirk

Authentication (Windows Server 2013) AD Cisco ISE problem

Background:

Has deployed two Cisco ISE 1.1.3. ISE will be used to authenticate users wireless access admin WLC and switches. Database backend is Microsoft running on Windows Server 2012 AD. Existing Cisco ACS 4.2 still running and authenticate users. There are two Cisco WLCs version 7.2.111.3.

Wireless users authenticates to AD, through works of GBA 4.2. Access admin WLC and switches to the announcement through ISE works. Authentication with PEAP-MSCHAPv2 access and admin PAP/ASCII wireless.

Problem:

Wireless users cannot authenticate to the announcement through ISE. This is the error message '11051 RADIUS packet contains invalid state attribute' & '24444 Active Directory failed because of an error that is not specified in the ISE'.

Conducted a detailed test of the AD of the ISE. The test was a success and the result seems fine except for the below:

xxdc01.XX.com (10.21.3.1)

Ping: 0 Mins Ago

Status: down

xxdc02.XX.com (10.21.3.2)

Ping: 0 Mins Ago

Status: down

xxdc01.XX.com

Last success: Thu Jan 1 10:00 1970

March 11 failure: read 11:18:04 2013

Success: 0

Chess: 11006

xxdc02.XX.com

Last success: Fri Mar 11 09:43:31 2013

March 11 failure: read 11:18:04 2013

Success: 25

Chess: 11006

Domain controller: xxdc02.xx.com:389

Domain controller type: unknown functional level DC: 5

Domain name: xx.COM

IsGlobalCatalogReady: TRUE

DomainFunctionality: 2 = (DS_BEHAVIOR_WIN2003)

ForestFunctionality: 2 = (DS_BEHAVIOR_WIN2003)

Action taken:

Log Cisco ISE and WLC by using the credentials of the AD. This excludes the connection AD, clock and AAA shared secret as the problem.

(2) wireless authentication tested using EAP-FAST, but same problem occurs.

(3) detailed error message shows below. This excludes any authentication and authorization policies. Even before hitting the authentication policy, the AD search fails.

12304 extract EAP-response containing PEAP stimulus / response

11808 extracted EAP-response containing EAP - MSCHAP VERSION challenge response to the internal method and accepting of EAP - MSCHAP VERSION such as negotiated

Evaluate the politics of identity

15006 set default mapping rule

15013 selected identity Store - AD1

24430 Authenticating user in Active Directory

24444 active Directory operation failed because of an error that is not specified in the ISE

(4) enabled the registration of debugging AD and had a look at the logging. Nothing significant, and no clue about the problem.

(5) wireless tested on different mobile phones with the same error and laptos

(6) delete and add new customer/features of AAA Cisco ISE and WLC

(7) ISE services restarted

(8) join domain on Cisco ISE

(9) notes of verified version of ISE 1.1.3 and WLC 7.2.111.3 for any open caveats. Find anything related to this problem.

10) there are two ISE and two deployed WLC. Tested a different combination of ISE1 to WLC1, ISE1 to WLC2, etc. This excludes a hardware problem of WLC.

Other possibilities/action:

1) test it on another version WLC. Will have to wait for approval of the failure to upgrade the WLC software.

(2) incompatibility between Cisco ISE and AD running on Microsoft Windows Server 2012

Did he experienced something similar to have ideas on why what is happening?

Thank you.

Update:

(1) built an another Cisco ISE 1.1.3 sever in another data center that uses the same domain but other domain controller. Thai domain controller running Windows Server 2008. This work and successful authentication.

(2) my colleague tested in a lab environment Cisco ISE 1.1.2 with Windows Server 2012. He has had the same problem as described.

This leads me to think that there is a compatibility issue of Cisco ISE with Windows Server 2012.

Yes, it seems that 1.1.3 doesn't support Server 2012 as of yet.

External identity Source OS/Version

Microsoft Windows Active Directory 2003 R2 32-bit and 64-bit

Active Directory Microsoft Windows 2008 32-bit and 64-bit

Microsoft Windows Active Directory 2008 R2 64-bit only

Microsoft Windows Active Directory 2003 32-bit only

http://www.Cisco.com/en/us/docs/security/ISE/1.1/compatibility/ise_sdt.PDF

Cisco ISE synchronization and NTP server

I am currently implementing Cisco ISE to our customer.

But having a little problem Cisco ISE cannot synchronize with NTP server.

Keep in mind, NTP servers in AD.

Currently, Cisco ISE synchronize just at the local level.

Cisco ISE implemented distributed mode, when there are two Cisco ISE installed on VMware (Administration & monitoring primary & secondary node), and another is the device (political Service node).

As a result of it might not sync server NTP and the ISE of Cisco, Cisco ISE often OUT-OF-SYN.

Is there a solution for this problem?

Gandhi,

This is a known issue, I have crossed upwards and have not read that you use AD as your NTP server, there have been problems with integration of the ISE and ACS with AD as their ntp source, please use another device like sources ntp, for example a router.

Thank you

Tarik Admani
* Please note the useful messages *.

Cisco ISE Patch 1.3 6 procedure

Hi team,

Please help me with the installation of fix on Cisco ISE version 1.3.0.876. I intend to patch our ISE with HA Set - up for patch 6. There also a way to upgrade? I read that you must install the hotfix on the primary node, then the secondary node automatically update to patch 6. Which command will work for me to check that the secondary image is upgraded to patch 6. Also, how much time it take to restart the application.

Thanks in advance!

Kind regards

Mady

Hi Mady-

You can perform the installation, restore and check the status of the patch directly from the graphical interface on the head node to Admin. You can reference to ISE 1.3 Administrator's Guide:

Install the Patch:

http://www.Cisco.com/c/en/us/TD/docs/security/ISE/1-3/admin_guide/b_ise_admin_guide_13/b_ise_admin_guide_sample_chapter_0101.html#ID202

Check the status of the patch:

http://www.Cisco.com/c/en/us/TD/docs/security/ISE/1-3/admin_guide/b_ise_admin_guide_13/b_ise_admin_guide_sample_chapter_0101.html#ID325

I hope this helps even if end :)

Thank you for evaluating useful messages!

Cisco ACS, multiple CA, assignment of VLAN relevant to the domain

Hi all

I searched for a solution to a specific customer requirement.

I want authenticate users with certificates from different RootCA wireless and assign them to one VLAN based on their field? Ideally, using the same SSID and a Cisco ACS server.

Is this possible? Has anyone seen that it works?

I realize that the ACS can have trust company for the relevant RootCA (dunno what version is needed for this?). And that assignment VLAN is also possible to a unique SSID based on RADIUS attributes. But I am not sure that these parts would fit together?

Would appreciate some advice!

Thanks in advance

Rob

Hello

Yes, this is possible. I suggest that you implement one by one to make sure that everything works, but no problem to do so. All recent versions of ACS allow this.

You can do mapping group from ad groups (a group for each area, so if you want to) and assign the vlan based on the mapping of this group.

GBA can trust several certification authorities and authenticate users with certificates of all these cases. It's just a matter of import these number certificate in the trust list.

And you can assign the vlan and use only one ssid as well.

I can't guide you on the procedure that it depends on which version you have and if you have IOS ap or WLC, but it is basically each function separated as in the config Guide and just used all together.

Nicolas

===

Remember responses of the rate that you find useful

4.1 of the ACS and 802. 1 x dynamic assignment of VLANS

Hi guys,.

a customer wants to implement assignment of VLANs with 802 dynamics. 1 x. The customer has the following facilities, Cisco ACS 4.1 for Windows, Cisco ASA 5540, CSA 5.2 with CSA MC, several routers and Cisco switches.

Now, the questations are, we can implement assignment of vlan dynamic without a unit of the ANC and the customer also wants to decide between customers with real antivirus signatures and the old signatures. Older clients are denied access to the anti-virus server and the update of the signature and if everything is ok, to have access to the internal network.

How could implement us this without a new hardware or software?

Any ideas? Thanks for help.

René

You can have a look on the frame of the NAC system. If you want only the posture validate cable customers then there no extra components to buy. If you want to go wireless, you will likely need to buy a Cisco client that supports wireless. You can get the configuration from here guide:

http://www.Cisco.com/application/PDF/en/us/guest/NetSol/ns617/c649/cdccont_0900aecd8040bbd8.PDF

I suggest you prototype and see what you think, the good thing is that you can deploy on a per switchport basis so you can make the installer on ACS without disturbing what is there already and apply it by configuring the switch.

That treats the assignment do VLAN authorization Cisco ISE?

Similar Questions

Maybe you are looking for