The ESP vpn remote access problem

I have vpn for remote access configured on the router from cisco 2901. Everything works well except 2 3g ipad. When I connect with the ipad 3g network it connects, but it is impossible to access the resources of the company. I talked to my phone provider and they told me that they have some problems NAT with ESP. and advised me to force vpn clients to use ports udp 500 and 4500. How do I configure my router to get there?

Thanks in advance

Hello

ISAKMP using UDP 500 port for connection management (Phase 1).

NAT - T (used when they are peripheral nat between two VPN end points) using UDP 4500 port.

So now your NAT - T router is configured by default, all you have to do is if you have an ACL on the external interface allow this traffic (Isakamp and NAT T) on some of its latest IOS versions, you do not have to apply the ACL that default VPN traffic (encrypted traffic bypasses the ACL).

If your condition is performed by default, great right thing! You can leave your phone provider, you are ready for the test.

Julio

Do rates all useful posts!

Tags: Cisco Security

Similar Questions

  • 1841 as Concentrator VPN remote access with manual keying

    Hi there and happy new year 2011 with best wishes!

    I would use a router 1841 as VPN hub for up to 20 remote connections.

    My remote (third party) clients have IPsec capacity supported by IKE and the Manual Keying, but I have not found information about simple configuration of Cisco VPN remote access (only on the easy VPN server).

    I'd like to configure the VPN entry Server Manual (I think it's an easy way to start), no problem to do?

    files:

    -topology

    -third party router Ethernet / 3G GUI IPsec with choice of algorithm auth

    -third party router Ethernet / 3G GUI IPsec with choice of encryption algorithm

    I feel so much better that someone help me!

    Kind regards

    Amaury

    As the remote end is third-party routers, the only option you have will be LAN-to-LAN IPSec VPN. You can not run VPN easy because that is only supported on Cisco devices.

    If your remote end has a static external ip address that ends the VPN, you can configure card crypto static LAN-to-LAN on the 1841 router, however, if your remote end has dynamic external ip address, you must configure card crypto dynamic LAN-to-LAN on the 1841 router. All remote LAN subnets must be unique.

  • Create different group with VPN remote access

    Hello world

    The last time, I ve put in place a VPN for remote access to my network with ASA 5510

    I ve access to all my internal LAn helped with my VPN

    But I want to set up a vpn group in the CLI for a different group of the user who accesses the different server or a different network on my local network.

    Example: computer group - access to 10.70.5.X network

    Group consultant network - access to 10.70.10.X

    I need to know how I can do this, and if you can give me some example script to complete this

    Here is my configuration:

    ASA Version 8.0 (2)
    !
    ASA-Vidrul host name
    vidrul domain name - ao.com
    activate 8Ry2YjIyt7RRXU24 encrypted password
    names of
    DNS-guard
    !
    interface Ethernet0/0
    nameif outside
    security-level 0
    address IP X.X.X.X 255.255.255.X
    !
    interface Ethernet0/1
    nameif inside
    security-level 100
    address IP X.X.X.X 255.255.255.X
    !
    interface Ethernet0/2
    Shutdown
    No nameif
    no level of security
    no ip address
    !
    interface Ethernet0/3
    Shutdown
    No nameif
    no level of security
    no ip address
    !
    interface Management0/0
    Description Port_Device_Management
    nameif management
    security-level 99
    address IP X.X.X.X 255.255.255.X
    management only
    !
    2KFQnbNIdI.2KYOU encrypted passwd
    passive FTP mode
    DNS server-group DefaultDNS
    vidrul domain name - ao.com
    access-list 100 scope ip allow a whole
    access-list extended 100 permit icmp any any echo
    access-list extended 100 permit icmp any any echo response
    vpn-vidrul_splitTunnelAcl permit 10.70.1.0 access list standard 255.255.255.0
    vpn-vidrul_splitTunnelAcl permit 10.70.99.0 access list standard 255.255.255.0
    inside_nat0_outbound list of allowed ip extended access all 10.70.255.0 255.255.255.0
    pager lines 24
    Outside 1500 MTU
    Within 1500 MTU
    MTU 1500 management
    IP local pool clientvpngroup 10.70.255.100 - 10.70.255.200 mask 255.255.255.0
    ICMP unreachable rate-limit 1 burst-size 1
    ASDM image disk0: / asdm - 602.bin
    don't allow no asdm history
    ARP timeout 14400
    Global 1 interface (outside)
    NAT (inside) 0-list of access inside_nat0_outbound
    NAT (inside) 1 10.70.0.0 255.255.0.0
    Access-group 100 in the interface inside
    Access-group 100 interface inside

    Timeout xlate 03:00
    Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
    Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
    Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
    Timeout, uauth 0:05:00 absolute
    dynamic-access-policy-registration DfltAccessPolicy
    Protocol RADIUS AAA-server 10.70.99.10
    AAA authentication enable LOCAL console
    the ssh LOCAL console AAA authentication
    LOCAL AAA authorization command
    Enable http server
    http 192.168.1.2 255.255.255.255 management
    No snmp server location
    No snmp Server contact
    Server enable SNMP traps snmp authentication linkup, linkdown cold start
    Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
    Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
    Dynamic crypto map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs
    SYSTEM_DEFAULT_CRYPTO_MAP game 65535 dynamic-map crypto transform-set ESP-DES-SHA ESP-DES-MD5
    outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
    outside_map interface card crypto outside
    crypto ISAKMP allow outside
    crypto ISAKMP policy 10
    preshared authentication
    the Encryption
    md5 hash
    Group 2
    life 86400
    Crypto isakmp nat-traversal 30
    Telnet 0.0.0.0 0.0.0.0 inside
    Telnet timeout 5
    SSH 0.0.0.0 0.0.0.0 outdoors
    SSH timeout 5
    Console timeout 0
    outside access management
    dhcpd manage 192.168.1.2 - 192.168.1.5
    dhcpd enable management
    !
    a basic threat threat detection
    Statistics-list of access threat detection
    !
    class-map inspection_default
    match default-inspection-traffic
    block-url-class of the class-map
    class-map imblock
    match any
    class-map P2P
    game port tcp eq www
    !
    !
    type of policy-card inspect dns migrated_dns_map_1
    parameters
    message-length maximum 512
    Policy-map global_policy
    class inspection_default
    inspect the migrated_dns_map_1 dns
    inspect the ftp
    inspect h323 h225
    inspect the h323 ras
    inspect the netbios
    inspect the rsh
    inspect the rtsp
    inspect the skinny
    inspect esmtp
    inspect sqlnet
    inspect sunrpc
    inspect the tftp
    inspect the sip
    inspect xdmcp
    Policy-map IM_P2P
    class imblock
    class P2P
    !
    global service-policy global_policy
    vpn-vidrul group policy internal
    vpn-vidrul group policy attributes
    Protocol-tunnel-VPN IPSec
    Split-tunnel-policy tunnelspecified
    Split-tunnel-network-list value vpn-vidrul_splitTunnelAcl
    value by default-field vidrul - ao.com
    test 274Y4GRAbNElaCoV of encrypted password privilege 0 username
    username admin privilege 15 encrypted password bTpUzgLxalekyhxQ
    attributes of user admin name
    Strategy-Group-VPN-vpn-vidrul
    username, password suporte zjQEaX/fm0NjEp4k encrypted privilege 15
    type tunnel-group vidrul-vpn remote access
    vpn-vidrul general-attributes tunnel-group
    address clientvpngroup pool
    Group Policy - by default-vpn-vidrul
    IPSec-vpn-vidrul tunnel group attributes
    pre-shared-key *.
    context of prompt hostname
    Cryptochecksum:d84e64c87cc5b263c84567e22400591c
    : end

    What you need to configure is to imitate the configuration on the tunnel-group and group strategy and to configure access to specific network you need.

    Currently, you have configured the following:

    vpn-vidrul group policy internal
    vpn-vidrul group policy attributes
    Protocol-tunnel-VPN IPSec
    Split-tunnel-policy tunnelspecified
    Split-tunnel-network-list value vpn-vidrul_splitTunnelAcl
    value by default-field vidrul - ao.com

    type tunnel-group vidrul-vpn remote access
    vpn-vidrul general-attributes tunnel-group
    address clientvpngroup pool
    Group Policy - by default-vpn-vidrul
    IPSec-vpn-vidrul tunnel group attributes
    pre-shared-key *.

    What you need is to create new group policy and the new tunnel-group and configure the tunnel split ACL to allow access to specific access required.

    The user must then connect with the new group name and the new pre-shared key (password).

    Hope that helps.

  • The Routing and remote access could not start, error 214500037 (0x80004005)

    My windows server 2003 r2, failed to start the Routing and remote access services. And in the event an observer log, it has error code
    Event ID: 7024, with service specific error 2147500037 (0x80004005)
    I tried to reset tcp/ip and replace ias.mdb and dnary.mdb by a new, but it did not work.

    Thank you

    Hi budhihartono,

    Since you are facing problems with windows server 2003 r2, it would be better suited in the Technet Windows forum. Please post your question in the following TechNet Windows server forum to improve assistance:

    http://social.technet.Microsoft.com/forums/en-us/category/WindowsServer

  • VPN remote access with router 2610

    Guys,

    A router Cisco 2610 series with IOS Version 11.3 (2) software version XA4 (fc1) will support a VPN remote access VPN Clients using standard Windows (LT2P on IPSec or PPTP) via a connection of Remote LAN-based access to wide band.

    I have bought this device and need an answer fast if possible.

    Thank you 1 million.

    Vito

    The navigation feature is the ideal tool for this:

    http://Tools.Cisco.com/ITDIT/CFN/JSP/index.jsp

    Search by function and enter PPTP and you will see he came to 12.2 code.

    Do the same for L2TP and you will see he came in 12.1 T code.

    The short answer is no.

  • The anyconnect vpn easy vpn Remote communication problem

    Hi team,

    I have a problem of communication of the anyconnect vpn easy vpn Remote I´ll explain better below and see the attachment
    topology:

    (1) VPN Tunnel between branch HQ - That´s OK
    (2) VPN Tunnel between Client AnyConnect to HQ - that s OK

    The idea is that the Anyconnect Client is reaching the local Branch Office network, but has not reached.
    Communication is established just when I begin a session (icmp or rdp) branch to the AnyConnect Client,.
    in this way, the communication is OK, but just for a few minutes.

    Could you help me?
    Below the IOS version and configurations

    ASA5505 Version 8.4 (7) 23 (Headquarters)
    ASA5505 Version 7.0000 23 (branch)

    Configuration of the server easy VPN (HQ) *.

    Crypto dynamic-map DYNAMIC - map 5 set transform-set ESP-AES-256-SHA ikev1
    Crypto card outside-link-2_map 1 ipsec-isakmp DYNAMIC-map Dynamics
    Crypto map link-outside-2_map-65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
    Crypto map interface outside-link-2_map outside-link-2

    ACL_EZVPN list standard access allowed 10.0.0.0 255.255.255.0
    ACL_EZVPN list standard access allowed 192.168.1.0 255.255.255.0
    ACL_EZVPN list standard access allowed 192.168.50.0 255.255.255.0
    ACL_EZVPN list standard access allowed 10.10.0.0 255.255.255.0

    internal EZVPN_GP group policy
    EZVPN_GP group policy attributes
    Split-tunnel-policy tunnelspecified
    value of Split-tunnel-network-list ACL_EZVPN
    allow to NEM
    type tunnel-group EZVPN_TG remote access
    attributes global-tunnel-group EZVPN_TG
    Group Policy - by default-EZVPN_GP
    IPSec-attributes tunnel-group EZVPN_TG
    IKEv1 pre-shared-key *.

    object-group network Obj_VPN_anyconnect-local
    object-network 192.168.1.0 255.255.255.0
    object-network 192.168.15.0 255.255.255.0
    object-group network Obj-VPN-anyconnect-remote
    object-network 192.168.50.0 255.255.255.0
    the NAT_EZVPN_Source object-group network
    object-network 192.168.1.0 255.255.255.0
    object-network 10.10.0.0 255.255.255.0
    the NAT_EZVPN_Destination object-group network
    object-network 10.0.0.0 255.255.255.0
     
    destination of Obj_VPN_anyconnect local Obj_VPN_anyconnect-local static NAT (inside, outside-link-2) Obj - VPN static source -.

    Remote AnyConnect VPN - Obj anyconnect-remote non-proxy-arp-search to itinerary
    destination NAT (inside, outside-link-2) static source NAT_EZVPN_Source NAT_EZVPN_Source NAT_EZVPN_Destination static

    NAT_EZVPN_Destination no-proxy-arp-search to itinerary
    NAT (outside-link-2, outside-link-2) static source Obj-VPN-anyconnect-remote Obj-VPN-anyconnect-remote static destination

    NAT_EZVPN_Destination NAT_EZVPN_Destination non-proxy-arp-search route

    Configuration VPN AnyConnect (HQ) *.

    WebVPN
    Select the outside link 2
    by default-idle-timeout 60
    AnyConnect essentials
    AnyConnect image disk0:/anyconnect-win-2.5.2014-k9.pkg 1
    AnyConnect profiles Remote_Connection_for_TS_Users disk0: / remote_connection_for_ts_users.xml
    AnyConnect enable
    tunnel-group-list activate

    tunnel of splitting allowed access list standard 192.168.1.0 255.255.255.0
    tunnel of splitting allowed access list standard 192.168.15.0 255.255.255.0
    tunnel of splitting allowed access list standard 10.0.0.0 255.255.255.0

    internal clientgroup group policy
    attributes of the strategy of group clientgroup
    WINS server no
    value of server DNS 192.168.1.41
    client ssl-VPN-tunnel-Protocol
    Split-tunnel-policy tunnelspecified
    Split-tunnel-network-list value split tunnel
    ipconnection.com.br value by default-field
    WebVPN
    AnyConnect Dungeon-Installer installed
    time to generate a new key 30 AnyConnect ssl
    AnyConnect ssl generate a new method ssl key
    AnyConnect value Remote_Connection_for_TS_Users type user profiles
    AnyConnect ask flawless anyconnect

    type tunnel-group sslgroup remote access
    tunnel-group sslgroup General-attributes
    address vpnpool pool
    authentication-server-group DC03
    Group Policy - by default-clientgroup
    tunnel-group sslgroup webvpn-attributes
    enable IPConnection-vpn-anyconnect group-alias

    object-group network Obj_VPN_anyconnect-local
    object-network 192.168.1.0 255.255.255.0
    object-network 192.168.15.0 255.255.255.0
    object-group network Obj-VPN-anyconnect-remote
    object-network 192.168.50.0 255.255.255.0
    the NAT_EZVPN_Source object-group network
    object-network 192.168.1.0 255.255.255.0
    object-network 10.10.0.0 255.255.255.0
    the NAT_EZVPN_Destination object-group network
    object-network 10.0.0.0 255.255.255.0
     
    destination of Obj_VPN_anyconnect local Obj_VPN_anyconnect-local static NAT (inside, outside-link-2) Obj - VPN static source -.

    Remote AnyConnect VPN - Obj anyconnect-remote non-proxy-arp-search to itinerary
    destination NAT (inside, outside-link-2) static source NAT_EZVPN_Source NAT_EZVPN_Source NAT_EZVPN_Destination static

    NAT_EZVPN_Destination no-proxy-arp-search to itinerary
    NAT (outside-link-2, outside-link-2) static source Obj-VPN-anyconnect-remote Obj-VPN-anyconnect-remote static destination

    NAT_EZVPN_Destination NAT_EZVPN_Destination non-proxy-arp-search route

    Hello

    communication works when you send the traffic of easyvpn derivation because it froms the IPSEC SA to pool local subnet and anyconnect HQ. The SA formed only when the branch initiates the connection as it's dynamic peer connection to HQ ASA.

    When there no SA between branch and HQ for this traffic, HQ ASA has no idea on where to send the anyconnect to network traffic.

    I hope this explains the cause.

    Kind regards

    Averroès.

  • Problem with ASA 5505 VPN remote access

    After about 1 year to have the VPN Client from Cisco connection to an ASA 5505 with no problems, all of a sudden one day it stops working. The customer is able to get a connection to the ASA and browse the local network for only about 30 seconds after the connection. After that, no access is available to the network behind the ASA. I have tried everything I can think of to try to solve the problem, but at this point, I'm just banging my head against a wall. Anyone know what could cause this?

    Here is the cfg running of the ASA

    ----------------------------------------------------------------------------------------

    : Saved

    :

    ASA Version 8.4 (1)

    !

    hostname NCHCO

    enable encrypted password xxxxxxxxxxxxxxx

    xxxxxxxxxxx encrypted passwd

    names of

    description of NCHCO name 192.168.2.0 City offices

    name 192.168.2.80 VPN_End

    name 192.168.2.70 VPN_Start

    !

    interface Vlan1

    nameif inside

    security-level 100

    IP 192.168.2.1 255.255.255.0

    !

    interface Vlan2

    nameif outside

    security-level 0

    IP address **. ***. 255.255.255.248

    !

    interface Ethernet0/0

    switchport access vlan 2

    Speed 100

    full duplex

    !

    interface Ethernet0/1

    !

    interface Ethernet0/2

    !

    interface Ethernet0/3

    !

    interface Ethernet0/4

    !

    interface Ethernet0/5

    !

    interface Ethernet0/6

    !

    interface Ethernet0/7

    !

    boot system Disk0: / asa841 - k8.bin

    passive FTP mode

    network of the NCHCO object

    Subnet 192.168.2.0 255.255.255.0

    network object obj - 192.168.1.0

    subnet 192.168.1.0 255.255.255.0

    network object obj - 192.168.2.64

    subnet 192.168.2.64 255.255.255.224

    network object obj - 0.0.0.0

    subnet 0.0.0.0 255.255.255.0

    network obj_any object

    subnet 0.0.0.0 0.0.0.0

    the Web server object network

    the FINX object network

    Home 192.168.2.11

    rdp service object

    source between 1-65535 destination eq 3389 tcp service

    Rdp description

    outside_nat0_outbound extended access list permit ip object NCHCO 192.168.1.0 255.255.255.0

    outside_nat0_outbound extended access list permit ip object NCHCO 192.168.2.0 255.255.255.0

    inside_nat0_outbound extended access list permit ip object NCHCO 192.168.1.0 255.255.255.0

    inside_nat0_outbound list of allowed ip extended access all 192.168.2.64 255.255.255.224

    permit access list extended ip 0.0.0.0 inside_nat0_outbound 255.255.255.0 192.168.2.64 255.255.255.224

    outside_1_cryptomap extended access list permit ip object NCHCO 192.168.1.0 255.255.255.0

    outside_1_cryptomap_1 extended access list permit ip object NCHCO 192.168.1.0 255.255.255.0

    LAN_Access list standard access allowed 192.168.2.0 255.255.255.0

    LAN_Access list standard access allowed 0.0.0.0 255.255.255.0

    NCHCO_splitTunnelAcl_1 list standard access allowed 192.168.2.0 255.255.255.0

    AnyConnect_Client_Local_Print deny ip extended access list a whole

    AnyConnect_Client_Local_Print list extended access permit tcp any any eq lpd

    Note AnyConnect_Client_Local_Print of access list IPP: Internet Printing Protocol

    AnyConnect_Client_Local_Print list extended access permit tcp any any eq 631

    print the access-list AnyConnect_Client_Local_Print Note Windows port

    AnyConnect_Client_Local_Print list extended access permit tcp any any eq 9100

    access-list AnyConnect_Client_Local_Print mDNS Note: multicast DNS protocol

    AnyConnect_Client_Local_Print list extended access permit udp any host 224.0.0.251 eq 5353

    AnyConnect_Client_Local_Print of access list LLMNR Note: link Local Multicast Name Resolution protocol

    AnyConnect_Client_Local_Print list extended access permit udp any host 224.0.0.252 eq 5355

    Note access list TCP/NetBIOS protocol AnyConnect_Client_Local_Print

    AnyConnect_Client_Local_Print list extended access permit tcp any any eq 137

    AnyConnect_Client_Local_Print list extended access udp allowed any any eq netbios-ns

    outside_access_in list extended access permit tcp any object FINX eq 3389

    outside_access_in_1 list extended access allowed object rdp any object FINX

    pager lines 24

    Enable logging

    asdm of logging of information

    Within 1500 MTU

    Outside 1500 MTU

    mask of VPN_Pool VPN_Start VPN_End of local pool IP 255.255.255.0

    ICMP unreachable rate-limit 1 burst-size 1

    ASDM image disk0: / asdm - 649.bin

    don't allow no asdm history

    ARP timeout 14400

    NAT (inside, all) static source NCHCO destination NCHCO static obj - 192.168.1.0 obj - 192.168.1.0

    NAT (inside, all) static source any any destination static obj - 192.168.2.64 obj - 192.168.2.64

    NAT (inside, all) source static obj - 0.0.0.0 0.0.0.0 - obj destination static obj - 192.168.2.64 obj - 192.168.2.64

    !

    network obj_any object

    NAT dynamic interface (indoor, outdoor)

    the FINX object network

    NAT (inside, outside) interface static service tcp 3389 3389

    Access-group outside_access_in_1 in interface outside

    Route outside 0.0.0.0 0.0.0.0 69.61.228.177 1

    Timeout xlate 03:00

    Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

    Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

    Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

    Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

    timeout tcp-proxy-reassembly 0:01:00

    dynamic-access-policy-registration DfltAccessPolicy

    network-acl outside_nat0_outbound

    WebVPN

    SVC request to enable default svc

    Enable http server

    http 192.168.1.0 255.255.255.0 inside

    http *. **. ***. 255.255.255.255 outside

    http *. **. ***. 255.255.255.255 outside

    http NCHCO 255.255.255.0 inside

    http 96.11.251.186 255.255.255.255 outside

    No snmp server location

    No snmp Server contact

    Server enable SNMP traps snmp authentication linkup, linkdown warmstart of cold start

    Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac

    Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac

    Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

    Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

    Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac

    Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

    Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac

    Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac

    Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac

    Crypto ipsec transform-set esp-3des esp-sha-hmac ikev1 l2tp-transform

    IKEv1 crypto ipsec transform-set l2tp-transformation mode transit

    Crypto ipsec transform-set vpn-transform ikev1 esp-aes-256 esp-sha-hmac

    Crypto ipsec transform-set esp-3des esp-sha-hmac TRANS_ESP_3DES_SHA ikev1

    transport mode encryption ipsec transform-set TRANS_ESP_3DES_SHA ikev1

    Crypto ipsec transform-set esp-3des esp-md5-hmac TRANS_ESP_3DES_MD5 ikev1

    transport mode encryption ipsec transform-set TRANS_ESP_3DES_MD5 ikev1

    Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac

    crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set

    crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 define ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5

    crypto dynamic-map dyn-map 10 set pfs Group1

    crypto dynamic-map dyn-map 10 set transform-set l2tp vpn-transform processing ikev1

    dynamic-map encryption dyn-map 10 value reverse-road

    Crypto-map dynamic outside_dyn_map 20 set transform-set ESP-3DES-SHA ikev1

    Crypto-map dynamic outside_dyn_map 20 the value reverse-road

    card crypto outside_map 1 match address outside_1_cryptomap

    card crypto outside_map 1 set pfs Group1

    peer set card crypto outside_map 1 74.219.208.50

    card crypto outside_map 1 set transform-set ESP-3DES-SHA ikev1

    map outside_map 20-isakmp ipsec crypto dynamic outside_dyn_map

    outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

    outside_map interface card crypto outside

    inside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

    inside crypto map inside_map interface

    card crypto vpn-map 1 match address outside_1_cryptomap_1

    card crypto vpn-card 1 set pfs Group1

    set vpn-card crypto map peer 1 74.219.208.50

    card crypto 1 set transform-set ESP-3DES-SHA ikev1 vpn-map

    dynamic vpn-map 10 dyn-map ipsec isakmp crypto map

    crypto isakmp identity address

    Crypto ikev1 allow inside

    Crypto ikev1 allow outside

    IKEv1 crypto ipsec-over-tcp port 10000

    IKEv1 crypto policy 10

    preshared authentication

    3des encryption

    md5 hash

    Group 2

    life 86400

    IKEv1 crypto policy 15

    preshared authentication

    aes-256 encryption

    sha hash

    Group 2

    life 86400

    IKEv1 crypto policy 35

    preshared authentication

    3des encryption

    sha hash

    Group 2

    life 86400

    enable client-implementation to date

    Telnet 192.168.1.0 255.255.255.0 inside

    Telnet NCHCO 255.255.255.0 inside

    Telnet timeout 5

    SSH 192.168.1.0 255.255.255.0 inside

    SSH NCHCO 255.255.255.0 inside

    SSH timeout 5

    Console timeout 0

    dhcpd address 192.168.2.150 - 192.168.2.225 inside

    dhcpd dns 216.68.4.10 216.68.5.10 interface inside

    lease interface 64000 dhcpd inside

    !

    a basic threat threat detection

    Statistics-list of access threat detection

    no statistical threat detection tcp-interception

    WebVPN

    internal DefaultRAGroup group strategy

    attributes of Group Policy DefaultRAGroup

    value of server DNS 192.168.2.1

    L2TP ipsec VPN-tunnel-Protocol ikev1

    nchco.local value by default-field

    attributes of Group Policy DfltGrpPolicy

    value of server DNS 192.168.2.1

    L2TP ipsec VPN-tunnel-Protocol ikev1 ssl-clientless ssl-client

    allow password-storage

    enable IPSec-udp

    enable dhcp Intercept 255.255.255.0

    the address value VPN_Pool pools

    internal NCHCO group policy

    NCHCO group policy attributes

    value of 192.168.2.1 DNS Server 8.8.8.8

    Ikev1 VPN-tunnel-Protocol

    Split-tunnel-policy tunnelspecified

    value of Split-tunnel-network-list NCHCO_splitTunnelAcl_1

    value by default-field NCHCO.local

    admin LbMiJuAJjDaFb2uw encrypted privilege 15 password username

    username privilege 15 encrypted password yB1lHEVmHZGj5C2Z 8njferg

    username NCHvpn99 password dhn. JzttvRmMbHsP encrypted

    attributes global-tunnel-group DefaultRAGroup

    address (inside) VPN_Pool pool

    address pool VPN_Pool

    authentication-server-group (inside) LOCAL

    authentication-server-group (outside LOCAL)

    LOCAL authority-server-group

    authorization-server-group (inside) LOCAL

    authorization-server-group (outside LOCAL)

    Group Policy - by default-DefaultRAGroup

    band-Kingdom

    band-band

    IPSec-attributes tunnel-group DefaultRAGroup

    IKEv1 pre-shared-key *.

    NOCHECK Peer-id-validate

    tunnel-group DefaultRAGroup ppp-attributes

    No chap authentication

    no authentication ms-chap-v1

    ms-chap-v2 authentication

    tunnel-group DefaultWEBVPNGroup ppp-attributes

    PAP Authentication

    ms-chap-v2 authentication

    tunnel-group 74.219.208.50 type ipsec-l2l

    IPSec-attributes tunnel-group 74.219.208.50

    IKEv1 pre-shared-key *.

    type tunnel-group NCHCO remote access

    attributes global-tunnel-group NCHCO

    address pool VPN_Pool

    Group Policy - by default-NCHCO

    IPSec-attributes tunnel-group NCHCO

    IKEv1 pre-shared-key *.

    !

    class-map inspection_default

    match default-inspection-traffic

    !

    !

    type of policy-card inspect dns preset_dns_map

    parameters

    maximum message length automatic of customer

    message-length maximum 512

    Policy-map global_policy

    class inspection_default

    inspect the preset_dns_map dns

    inspect the ftp

    inspect h323 h225

    inspect the h323 ras

    inspect the rsh

    inspect the rtsp

    inspect esmtp

    inspect sqlnet

    inspect the skinny

    inspect sunrpc

    inspect xdmcp

    inspect the sip

    inspect the netbios

    inspect the tftp

    Review the ip options

    !

    global service-policy global_policy

    context of prompt hostname

    call-home

    Profile of CiscoTAC-1

    no active account

    http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address

    email address of destination [email protected] / * /

    destination-mode http transport

    Subscribe to alert-group diagnosis

    Subscribe to alert-group environment

    Subscribe to alert-group monthly periodic inventory

    monthly periodicals to subscribe to alert-group configuration

    daily periodic subscribe to alert-group telemetry

    Cryptochecksum:a2110206e1af06974c858fb40c6de2fc

    : end

    ASDM image disk0: / asdm - 649.bin

    ASDM VPN_Start 255.255.255.255 inside location

    ASDM VPN_End 255.255.255.255 inside location

    don't allow no asdm history

    ---------------------------------------------------------------------------------------------------------------

    And here are the logs of the Cisco VPN Client when sailing, then is unable to browse the network behind the ASA:

    ---------------------------------------------------------------------------------------------------------------

    Cisco Systems VPN Client Version 5.0.07.0440

    Copyright (C) 1998-2010 Cisco Systems, Inc.. All rights reserved.

    Customer type: Windows, Windows NT

    Running: 6.1.7601 Service Pack 1

    Config files directory: C:\Program Files (x 86) \Cisco Systems\VPN Client\

    1 09:44:55.677 01/10/13 Sev = Info/6 CERT / 0 x 63600026

    Try to find a certificate using hash Serial.

    2 09:44:55.677 01/10/13 Sev = Info/6 CERT / 0 x 63600027

    Found a certificate using hash Serial.

    3 09:44:55.693 01/10/13 Sev = Info/6 GUI/0x63B00011

    RELOADED successfully certificates in all certificate stores.

    4 09:45:02.802 10/01/13 Sev = Info/4 CM / 0 x 63100002

    Start the login process

    5 09:45:02.802 01/10/13 Sev = Info/4 CM / 0 x 63100004

    Establish a secure connection

    6 09:45:02.802 01/10/13 Sev = Info/4 CM / 0 x 63100024

    Attempt to connect with the server "*." **. ***. *** »

    7 09:45:02.802 10/01/13 Sev = Info/6 IKE/0x6300003B

    Try to establish a connection with *. **. ***. ***.

    8 09:45:02.818 10/01/13 Sev = Info/4 IKE / 0 x 63000001

    From IKE Phase 1 negotiation

    9 09:45:02.865 10/01/13 Sev = Info/4 IKE / 0 x 63000013

    SEND to > ISAKMP OAK AG (SA, KE, NO, ID, VID (Xauth), VID (dpd), VID (Frag), VID(Nat-T), VID (Unity)) to *. **. ***. ***

    10 09:45:02.896 10/01/13 Sev = Info/5 IKE/0x6300002F

    Received packet of ISAKMP: peer = *. **. ***. ***

    11 09:45:02.896 10/01/13 Sev = Info/4 IKE / 0 x 63000014

    RECEIVING< isakmp="" oak="" ag="" (sa,="" ke,="" non,="" id,="" hash,="" vid(unity),="" vid(xauth),="" vid(dpd),="" vid(nat-t),="" nat-d,="" nat-d,="" vid(frag),="" vid(?))="" from="">

    12 09:45:02.896 10/01/13 Sev = Info/5 IKE / 0 x 63000001

    Peer is a compatible peer Cisco-Unity

    13 09:45:02.896 01/10/13 Sev = Info/5 IKE / 0 x 63000001

    Peer supports XAUTH

    14 09:45:02.896 01/10/13 Sev = Info/5 IKE / 0 x 63000001

    Peer supports the DPD

    15 09:45:02.896 01/10/13 Sev = Info/5 IKE / 0 x 63000001

    Peer supports NAT - T

    16 09:45:02.896 01/10/13 Sev = Info/5 IKE / 0 x 63000001

    Peer supports fragmentation IKE payloads

    17 09:45:02.927 01/10/13 Sev = Info/6 IKE / 0 x 63000001

    IOS Vendor ID successful construction

    18 09:45:02.927 01/10/13 Sev = Info/4 IKE / 0 x 63000013

    SENDING > ISAKMP OAK AG * (HASH, NOTIFY: NAT - D, NAT - D, VID (?), STATUS_INITIAL_CONTACT, VID (Unity)) to *. **. ***. ***

    19 09:45:02.927 01/10/13 Sev = Info/4 IKE / 0 x 63000083

    IKE port in use - Local Port = 0xDD3B, Remote Port = 0x01F4

    20 09:45:02.927 01/10/13 Sev = Info/5 IKE / 0 x 63000072

    Automatic NAT detection status:

    Remote endpoint is NOT behind a NAT device

    This effect is NOT behind a NAT device

    21 09:45:02.927 01/10/13 Sev = Info/4 CM/0x6310000E

    ITS established Phase 1.  1 crypto IKE Active SA, 0 IKE SA authenticated user in the system

    22 09:45:02.943 10/01/13 Sev = Info/5 IKE/0x6300002F

    Received packet of ISAKMP: peer = *. **. ***. ***

    23 09:45:02.943 01/10/13 Sev = Info/4 IKE / 0 x 63000014

    RECEIVING< isakmp="" oak="" trans="" *(hash,="" attr)="" from="">

    24 09:45:02.943 01/10/13 Sev = Info/4 CM / 0 x 63100015

    Launch application xAuth

    25 09:45:03.037 01/10/13 Sev = Info/6 GUI/0x63B00012

    Attributes of the authentication request is 6: 00.

    26 09:45:03.037 01/10/13 Sev = Info/4 CM / 0 x 63100017

    xAuth application returned

    27 09:45:03.037 10/01/13 Sev = Info/4 IKE / 0 x 63000013

    SEND to > ISAKMP OAK TRANS *(HASH, ATTR) to *. **. ***. ***

    28 09:45:03.037 10/01/13 Sev = Info/4 IPSEC / 0 x 63700008

    IPSec driver started successfully

    29 09:45:03.037 01/10/13 Sev = Info/4 IPSEC / 0 x 63700014

    Remove all keys

    30 09:45:03.083 01/10/13 Sev = Info/5 IKE/0x6300002F

    Received packet of ISAKMP: peer = *. **. ***. ***

    31 09:45:03.083 01/10/13 Sev = Info/4 IKE / 0 x 63000014

    RECEIVING< isakmp="" oak="" trans="" *(hash,="" attr)="" from="">

    32 09:45:03.083 01/10/13 Sev = Info/4 IKE / 0 x 63000013

    SEND to > ISAKMP OAK TRANS *(HASH, ATTR) to *. **. ***. ***

    33 09:45:03.083 01/10/13 Sev = Info/4 CM/0x6310000E

    ITS established Phase 1.  1 crypto IKE Active SA, 1 IKE SA authenticated user in the system

    34 09:45:03.083 01/10/13 Sev = Info/5 IKE/0x6300005E

    Customer address a request from firewall to hub

    35 09:45:03.083 01/10/13 Sev = Info/4 IKE / 0 x 63000013

    SEND to > ISAKMP OAK TRANS *(HASH, ATTR) to *. **. ***. ***

    36 09:45:03.146 01/10/13 Sev = Info/5 IKE/0x6300002F

    Received packet of ISAKMP: peer = *. **. ***. ***

    37 09:45:03.146 01/10/13 Sev = Info/4 IKE / 0 x 63000014

    RECEIVING< isakmp="" oak="" trans="" *(hash,="" attr)="" from="" **.**.***.***="" isakmp="" oak="" trans="" *(hash,="" attr)="" from="">

    38 09:45:03.146 01/10/13 Sev = Info/5 IKE / 0 x 63000010

    MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_ADDRESS:, value = 192.168.2.70

    39 09:45:03.146 01/10/13 Sev = Info/5 IKE / 0 x 63000010

    MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_NETMASK:, value = 255.255.255.0

    40 09:45:03.146 01/10/13 Sev = Info/5 IKE / 0 x 63000010

    MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_DNS (1):, value = 192.168.2.1

    41 09:45:03.146 01/10/13 Sev = Info/5 IKE / 0 x 63000010

    MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_DNS (2):, value = 8.8.8.8

    42 09:45:03.146 01/10/13 Sev = Info/5 IKE/0x6300000D

    MODE_CFG_REPLY: Attribute = MODECFG_UNITY_SAVEPWD:, value = 0x00000001

    43 09:45:03.146 01/10/13 Sev = Info/5 IKE/0x6300000D

    MODE_CFG_REPLY: Attribute = MODECFG_UNITY_SPLIT_INCLUDE (# of split_nets), value = 0x00000001

    44 09:45:03.146 10/01/13 Sev = Info/5 IKE/0x6300000F

    SPLIT_NET #1

    = 192.168.2.0 subnet

    mask = 255.255.255.0

    Protocol = 0

    SRC port = 0

    port dest = 0

    45 09:45:03.146 10/01/13 Sev = Info/5 IKE/0x6300000E

    MODE_CFG_REPLY: Attribute = MODECFG_UNITY_DEFDOMAIN:, value = NCHCO.local

    46 09:45:03.146 01/10/13 Sev = Info/5 IKE/0x6300000D

    MODE_CFG_REPLY: Attribute = MODECFG_UNITY_UDP_NAT_PORT, value = 0 x 00002710

    47 09:45:03.146 01/10/13 Sev = Info/5 IKE/0x6300000D

    MODE_CFG_REPLY: Attribute = MODECFG_UNITY_PFS:, value = 0x00000000

    48 09:45:03.146 01/10/13 Sev = Info/5 IKE/0x6300000E

    MODE_CFG_REPLY: Attribute = APPLICATION_VERSION, value = 8.4 (1) Cisco systems, Inc. ASA5505 Version built by manufacturers on Tuesday, January 31, 11 02:11

    49 09:45:03.146 01/10/13 Sev = Info/5 IKE/0x6300000D

    MODE_CFG_REPLY: Attribute = MODECFG_UNITY_SMARTCARD_REMOVAL_DISCONNECT:, value = 0x00000001

    50 09:45:03.146 01/10/13 Sev = Info/4 CM / 0 x 63100019

    Data in mode Config received

    51 09:45:03.146 01/10/13 Sev = Info/4 IKE / 0 x 63000056

    Received a request from key driver: local IP = 192.168.2.70, GW IP = *. **. ***. remote IP address = 0.0.0.0

    52 09:45:03.146 01/10/13 Sev = Info/4 IKE / 0 x 63000013

    SEND to > ISAKMP OAK QM * (HASH, SA, NO, ID, ID) to *. **. ***. ***

    53 09:45:03.177 01/10/13 Sev = Info/5 IKE/0x6300002F

    Received packet of ISAKMP: peer = *. **. ***. ***

    54 09:45:03.177 01/10/13 Sev = Info/4 IKE / 0 x 63000014

    RECEIVING< isakmp="" oak="" info="" *(hash,="" notify:status_resp_lifetime)="" from="">

    55 09:45:03.177 01/10/13 Sev = Info/5 IKE / 0 x 63000045

    Answering MACHINE-LIFE notify has value of 86400 seconds

    56 09:45:03.177 01/10/13 Sev = Info/5 IKE / 0 x 63000047

    This SA was already alive for 1 second, expiration of adjustment to 86399 seconds now

    57 09:45:03.193 01/10/13 Sev = Info/5 IKE/0x6300002F

    Received packet of ISAKMP: peer = *. **. ***. ***

    58 09:45:03.193 01/10/13 Sev = Info/4 IKE / 0 x 63000014

    RECEIVING< isakmp="" oak="" qm="" *(hash,="" sa,="" non,="" id,="" id,="" notify:status_resp_lifetime)="" from="">

    59 09:45:03.193 01/10/13 Sev = Info/5 IKE / 0 x 63000045

    Answering MACHINE-LIFE notify is set to 28800 seconds

    60 09:45:03.193 01/10/13 Sev = Info/4 IKE / 0 x 63000013

    SEND to > ISAKMP OAK QM * (HASH) to *. **. ***. ***

    61 09:45:03.193 01/10/13 Sev = Info/5 IKE / 0 x 63000059

    IPsec Security Association of loading (MsgID = SPI OUTBOUND SPI INCOMING = 0x3EBEBFC5 0xAAAF4C1C = 967A3C93)

    62 09:45:03.193 01/10/13 Sev = Info/5 IKE / 0 x 63000025

    OUTGOING ESP SPI support: 0xAAAF4C1C

    63 09:45:03.193 01/10/13 Sev = Info/5 IKE / 0 x 63000026

    Charges INBOUND ESP SPI: 0x3EBEBFC5

    64 09:45:03.193 01/10/13 Sev = Info/5 CVPND / 0 x 63400013

    Destination mask subnet Gateway Interface metric

    0.0.0.0 0.0.0.0 96.11.251.1 96.11.251.149 261

    96.11.251.0 255.255.255.0 96.11.251.149 96.11.251.149 261

    96.11.251.149 255.255.255.255 96.11.251.149 96.11.251.149 261

    96.11.251.255 255.255.255.255 96.11.251.149 96.11.251.149 261

    127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 306

    127.0.0.1 255.255.255.255 127.0.0.1 127.0.0.1 306

    127.255.255.255 255.255.255.255 127.0.0.1 127.0.0.1 306

    192.168.1.0 255.255.255.0 192.168.1.3 192.168.1.3 261

    192.168.1.3 255.255.255.255 192.168.1.3 192.168.1.3 261

    192.168.1.255 255.255.255.255 192.168.1.3 192.168.1.3 261

    224.0.0.0 240.0.0.0 127.0.0.1 127.0.0.1 306

    224.0.0.0 240.0.0.0 96.11.251.149 96.11.251.149 261

    224.0.0.0 240.0.0.0 192.168.1.3 192.168.1.3 261

    255.255.255.255 255.255.255.255 127.0.0.1 127.0.0.1 306

    255.255.255.255 255.255.255.255 96.11.251.149 96.11.251.149 261

    255.255.255.255 255.255.255.255 192.168.1.3 192.168.1.3 261

    65 09:45:03.521 01/10/13 Sev = Info/6 CVPND / 0 x 63400001

    Launch VAInst64 for controlling IPSec virtual card

    66 09:45:03.896 01/10/13 Sev = Info/4 CM / 0 x 63100034

    The virtual card has been activated:

    IP=192.168.2.70/255.255.255.0

    DNS = 192.168.2.1, 8.8.8.8

    WINS = 0.0.0.0 0.0.0.0

    Domain = NCHCO.local

    Split = DNS names

    67 09:45:03.912 01/10/13 Sev = Info/5 CVPND / 0 x 63400013

    Destination mask subnet Gateway Interface metric

    0.0.0.0 0.0.0.0 96.11.251.1 96.11.251.149 261

    96.11.251.0 255.255.255.0 96.11.251.149 96.11.251.149 261

    96.11.251.149 255.255.255.255 96.11.251.149 96.11.251.149 261

    96.11.251.255 255.255.255.255 96.11.251.149 96.11.251.149 261

    127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 306

    127.0.0.1 255.255.255.255 127.0.0.1 127.0.0.1 306

    127.255.255.255 255.255.255.255 127.0.0.1 127.0.0.1 306

    192.168.1.0 255.255.255.0 192.168.1.3 192.168.1.3 261

    192.168.1.3 255.255.255.255 192.168.1.3 192.168.1.3 261

    192.168.1.255 255.255.255.255 192.168.1.3 192.168.1.3 261

    224.0.0.0 240.0.0.0 127.0.0.1 127.0.0.1 306

    224.0.0.0 240.0.0.0 96.11.251.149 96.11.251.149 261

    224.0.0.0 240.0.0.0 192.168.1.3 192.168.1.3 261

    224.0.0.0 240.0.0.0 0.0.0.0 0.0.0.0 261

    255.255.255.255 255.255.255.255 127.0.0.1 127.0.0.1 306

    255.255.255.255 255.255.255.255 96.11.251.149 96.11.251.149 261

    255.255.255.255 255.255.255.255 192.168.1.3 192.168.1.3 261

    255.255.255.255 255.255.255.255 0.0.0.0 0.0.0.0 261

    68 09:45:07.912 01/10/13 Sev = Info/4 CM / 0 x 63100038

    Were saved successfully road to file changes.

    69 09:45:07.912 01/10/13 Sev = Info/5 CVPND / 0 x 63400013

    Destination mask subnet Gateway Interface metric

    0.0.0.0 0.0.0.0 96.11.251.1 96.11.251.149 261

    **. **. ***. 255.255.255.255 96.11.251.1 96.11.251.149 100

    96.11.251.0 255.255.255.0 96.11.251.149 96.11.251.149 261

    96.11.251.149 255.255.255.255 96.11.251.149 96.11.251.149 261

    96.11.251.255 255.255.255.255 96.11.251.149 96.11.251.149 261

    127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 306

    127.0.0.1 255.255.255.255 127.0.0.1 127.0.0.1 306

    127.255.255.255 255.255.255.255 127.0.0.1 127.0.0.1 306

    192.168.1.0 255.255.255.0 192.168.1.3 192.168.1.3 261

    192.168.1.3 255.255.255.255 192.168.1.3 192.168.1.3 261

    192.168.1.255 255.255.255.255 192.168.1.3 192.168.1.3 261

    192.168.2.0 255.255.255.0 192.168.2.70 192.168.2.70 261

    192.168.2.0 255.255.255.0 192.168.2.1 192.168.2.70 100

    192.168.2.70 255.255.255.255 192.168.2.70 192.168.2.70 261

    192.168.2.255 255.255.255.255 192.168.2.70 192.168.2.70 261

    224.0.0.0 240.0.0.0 127.0.0.1 127.0.0.1 306

    224.0.0.0 240.0.0.0 96.11.251.149 96.11.251.149 261

    224.0.0.0 240.0.0.0 192.168.1.3 192.168.1.3 261

    224.0.0.0 240.0.0.0 192.168.2.70 192.168.2.70 261

    255.255.255.255 255.255.255.255 127.0.0.1 127.0.0.1 306

    255.255.255.255 255.255.255.255 96.11.251.149 96.11.251.149 261

    255.255.255.255 255.255.255.255 192.168.1.3 192.168.1.3 261

    255.255.255.255 255.255.255.255 192.168.2.70 192.168.2.70 261

    70 09:45:07.912 01/10/13 Sev = Info/6 CM / 0 x 63100036

    The routing table has been updated for the virtual card

    71 09:45:07.912 01/10/13 Sev = Info/4 CM/0x6310001A

    A secure connection established

    72 09:45:07.943 01/10/13 Sev = Info/4 CM/0x6310003B

    Look at address added to 96.11.251.149.  Current host name: psaserver, current address (s): 192.168.2.70, 96.11.251.149, 192.168.1.3.

    73 09:45:07.943 01/10/13 Sev = Info/4 CM/0x6310003B

    Look at address added to 192.168.2.70.  Current host name: psaserver, current address (s): 192.168.2.70, 96.11.251.149, 192.168.1.3.

    74 09:45:07.943 01/10/13 Sev = Info/5 CM / 0 x 63100001

    Did not find the smart card to watch for removal

    75 09:45:07.943 01/10/13 Sev = Info/4 IPSEC / 0 x 63700014

    Remove all keys

    76 09:45:07.943 01/10/13 Sev = Info/4 IPSEC / 0 x 63700010

    Creates a new key structure

    77 09:45:07.943 01/10/13 Sev = Info/4 IPSEC/0x6370000F

    Adding key with SPI = 0x1c4cafaa in the list of keys

    78 09:45:07.943 01/10/13 Sev = Info/4 IPSEC / 0 x 63700010

    Creates a new key structure

    79 09:45:07.943 01/10/13 Sev = Info/4 IPSEC/0x6370000F

    Adding key with SPI = 0xc5bfbe3e in the list of keys

    80 09:45:07.943 01/10/13 Sev = Info/4 IPSEC/0x6370002F

    Assigned WILL interface private addr 192.168.2.70

    81 09:45:07.943 01/10/13 Sev = Info/4 IPSEC / 0 x 63700037

    Configure the public interface: 96.11.251.149. SG: **.**.***.***

    82 09:45:07.943 10/01/13 Sev = Info/6 CM / 0 x 63100046

    Define indicator tunnel set up in the registry to 1.

    83 09:45:13.459 01/10/13 Sev = Info/4 IKE / 0 x 63000013

    SEND to > ISAKMP OAK INFO * (HASH, NOTIFY: DPD_REQUEST) to *. **. ***. ***

    84 09:45:13.459 01/10/13 Sev = Info/6 IKE/0x6300003D

    Upon request of the DPD to *. **. ***. , our seq # = 107205276

    85 09:45:13.474 01/10/13 Sev = Info/5 IKE/0x6300002F

    Received packet of ISAKMP: peer = *. **. ***. ***

    86 09:45:13.474 01/10/13 Sev = Info/4 IKE / 0 x 63000014

    RECEIVING< isakmp="" oak="" info="" *(hash,="" notify:dpd_ack)="" from="">

    87 09:45:13.474 01/10/13 Sev = Info/5 IKE / 0 x 63000040

    Receipt of DPO ACK to *. **. ***. seq # receipt = 107205276, seq # expected is 107205276

    88 09:45:15.959 01/10/13 Sev = Info/4 IPSEC / 0 x 63700019

    Activate key dating SPI = 0x1c4cafaa key with SPI = 0xc5bfbe3e

    89 09:46:00.947 10/01/13 Sev = Info/4 IKE / 0 x 63000013

    SEND to > ISAKMP OAK INFO * (HASH, NOTIFY: DPD_REQUEST) to *. **. ***. ***

    90 09:46:00.947 01/10/13 Sev = Info/6 IKE/0x6300003D

    Upon request of the DPD to *. **. ***. , our seq # = 107205277

    91 09:46:01.529 01/10/13 Sev = Info/5 IKE/0x6300002F

    Received packet of ISAKMP: peer = *. **. ***. ***

    92 09:46:01.529 01/10/13 Sev = Info/4 IKE / 0 x 63000014

    RECEIVING< isakmp="" oak="" info="" *(hash,="" notify:dpd_ack)="" from="">

    93 09:46:01.529 01/10/13 Sev = Info/5 IKE / 0 x 63000040

    Receipt of DPO ACK to *. **. ***. seq # receipt = 107205277, seq # expected is 107205277

    94 09:46:11.952 01/10/13 Sev = Info/4 IKE / 0 x 63000013

    SEND to > ISAKMP OAK INFO * (HASH, NOTIFY: DPD_REQUEST) to *. **. ***. ***

    95 09:46:11.952 01/10/13 Sev = Info/6 IKE/0x6300003D

    Upon request of the DPD to *. **. ***. , our seq # = 107205278

    96 09:46:11.979 01/10/13 Sev = Info/5 IKE/0x6300002F

    Received packet of ISAKMP: peer = *. **. ***. ***

    97 09:46:11.979 01/10/13 Sev = Info/4 IKE / 0 x 63000014

    RECEIVING< isakmp="" oak="" info="" *(hash,="" notify:dpd_ack)="" from="">

    98 09:46:11.979 01/10/13 Sev = Info/5 IKE / 0 x 63000040

    Receipt of DPO ACK to *. **. ***. seq # receipt = 107205278, seq # expected is 107205278

    ---------------------------------------------------------------------------------------------------------------

    Any help would be appreciated, thanks!

    try to refuse the ACL (access-list AnyConnect_Client_Local_Print extended deny ip any one) at the end of the ACL.

  • ODA IP ASA when you browse the web via remote access vpn

    Hi all

    I was wondering if it is possible to configure an ASA5510 in a way to allow users remote access VPN use external IP of the ASA when browsing the web. So what I'm looking for is a solution to hide my IP address and use the IP address of the ASA, when browsing.

    The firmware version of the ASA is 9.1 (6)

    Thanks in advance

    Hello

    What you want to achieve is calles u-turn.

    You must enable the feature allowed same-security-traffic intra-interface

    For the configuration of the asa, here's the Cisco documentation (I don't copy paste on the post):

    http://www.Cisco.com/c/en/us/support/docs/security/ASA-5500-x-series-NEX...

    Thank you

    PS: Please do not forget to rate and score as good response if this solves your problem

  • Cisco ASA, connect an IP address on the OUTSIDE of the VPN remote access

    Hello

    I tried to find resources on the net but could not find a solution, then post it here. Maybe someone can help.

    So the problem is that I'm trying to access a server on the cloud for remote VPN access (cisco asa 5510).

    The server on the cloud (54.54.54.54) is only accessible from the outside interface (192.168.11.2) NY Firewall (cisco asa 5510)

    I added some ACE for this in the ACL of VPN tunnel to divide.

    NY-standard host allowed fw # access - list vpn_remote-customer 54.54.54.54

    And I see the road added to my cliet machine after the VPN connection, but still it cannot connect to this server.

    The network INTERIOR, I can connect to the server.

    Thanks in advance.

    Hello

    This is most likely a problem with NAT hair/U-turn hairpin.

    Will need to see the configurations or you would need to check yourself

    I don't know what your version of the Software ASA is to be like who determines what is the format of NAT configuration.

    So far, you have confirmed that the ASA VPN configuration provides the VPN Client with the route to the remote server. Then in circulation should be tunnel to the ASA.

    Then, you will need to check the output of this command

    See the race same-security-traffic

    You should see the command in the output below

    permit same-security-traffic intra-interface

    If you do not, you will need to add it. This effect of controls is to allow traffic to enter an interface and exit through the same interface. In your case this applies to Internet VPN Client traffic to the remote server as it between ' outside ' and spell through the 'outside'.

    Then, should ensure that dynamic PAT is configured for the VPN Clients.

    8.2 software (and below)

    You most likely have a dynamic configuration PAT like that on the firewall, if levels of above running software version

    Global 1 interface (outside)

    NAT (inside) 1 0.0.0.0 0.0.0.0

    In this situation if we wanted to add dynamic PAT for a pool of VPN, we would add

    NAT (outside) 1

    This would allow users to use the same public IP address as LAN users, when accessing the remote VPN server

    Software 8.3 (and above)

    Because the NAT configuration format is completely different in the latest software, you could probably just add a new configuration of NAT completely without adding a

    network of the VPN-PAT object

    subnet

    dynamic NAT interface (outdoors, outdoor)

    Of course, its possible that there could be some configuration NAT already on the device which could cause problems for this configuration. If this does not work then that we would have to look at the actual configurations on the ASA.

    Hope this helps

    Let me know how it goes

    -Jouni

  • How to configure VPN remote access to use a specific Interface and the road

    I add a second external connection to an existing system on a 5510 ASA ASA V8.2 with 6.4 AMPS

    I added the new WAN using another interface (newwan).

    The intention is to bring more internet traffic on the new road/interface (newwan), but keep our existing VPN using the old interface (outside).

    I used the ASDM GUI to make changes and most of it works.

    That is to say. The default route goes via (newwan)

    Coming out of a VPN using a site to character the way previous (out) as they now have static routes to achieve this.

    The only problem is that remote incomming VPN access Anyconnect do not work.

    I put the default static route to use the new interface (newwan) and the default tunnel road be (outside), but that's the point is will not...

    I can either ping external IP address from an external location.

    It seems that the external interface doesn't send traffic to the - external interface (or at least that's where I think the problem lies). How can I force responses to remote VPN entering IPS unknown traffic to go back on the external interface?

    The only change I have to do to make it work again on the external interface is to make the default static route to use external interface. Calling all internet traffic to the (external connection) original

    Pointers appreciated.

    William

    William,

    As it is right now that you will not use the same interface you have road to terminate remote access unless you know their IP addresses by default.

    In one of the designs that I saw that we did something like that.

    (ISP cloud) - edge router - ASA.

    The edge router, you can make PAT within the interface for incoming traffic on port udp/500 and UDP/4500 (you may need to add exceptions to your L2L static) of the router. It's dirty, I would not say, it is recommended, but apparently it worked.

    On routers, this kind of situation is easily solved using VRF-lite with crypto.

    M.

  • IP overlapping between VPN remote access and within the interface

    Hi all

    I tried to replace an ASA and configured vpn for remote access using cisco VPN client.

    Remote access users are not able to access within the network, but have no problem accessing the network through a VPN site-to site.

    One thing to note is that remote access VPN users are assigned an ip address of 10.X.3.1 - 10.X.3.200 mask 255.255.255.0. The inside interface is on 10.X.1.2 255.255.0.0.

    Remote access users will have no problem to access within the network if the pool of the vpn client is changed to 192.168.1.1 to 192.168.1.100.

    ASA errors

    6 January 7, 2012 16:25:08 302013 10.X.3.1 27724 3389 10.X.1.66 built of TCP connections incoming 20940 for outside:10.X.3.1/27724 (10.X.3.1/27724)(LOCAL\Cisco) at inside:10.X.1.66/3389 (10.X.1.66/3389) (Cisco)

    6 January 7, 2012 16:25:08 106015 10.X.1.66 3389 10.X.3.1 27724 Deny TCP 10.X.1.66/3389 to 10.X.3.1/27724 flags SYN ACK on dmz interface (no link)

    I understand that the overlap between access ip address range remote vpn network interface network and inside will cause routing problems, but why the syn - ack makes its appearance in the DMZ interface? The interface of the DMZ is on ip address 172.16.Y.1 255.255.255.0.

    I intend to reduce the interface 10.X.0.0 255.255.254.0 inside if it is in fact a routing problem due to the IP address that overlap, but I understand why the syn - ack comes from the dmz interface and the diagnosis of the problem is correct. I check with the customer and was informed that the existing design works on an another ASA with no such problems.

    I agree what you said and also tried, but it does not work.

    http://www.Cisco.com/en/us/products/ps6120/products_tech_note09186a00807e0aca.shtml#overlap

    Solution, that you already know

    Solution

    Always ensure that the IP addresses in the pool should be assigned to VPN, network clients internal head unit and the internal network to the VPN Client must be in different networks. You can assign the same major network with different subnets, but sometimes the routing problems.

    Thank you

    Ajay

  • Cannot Ping across the VPN remote access

    Hello world

    I hope I posted this in the right place!

    I'm a bit new to Cisco IOS, so please forgive me if I ask a stupid question!

    We have a firewall of 515E PIX 6.3 (4) on which I used the VPN Wizard to set up a remote access VPN the Cisco VPN client on the external interface.

    When I connect to home on my laptop Windows XP Pro SP2 running Cisco VPN Client 4.0.5(C) I seem to be able to connect to most of the network resources (IE file shares, I can RDP into servers, etc.) but I can't seem to be able to ping anything : I just request times out.

    I'm sure it's something stupid I've done (or not done).

    I have attached my config and would be grateful if someone could take a look and point me in the right direction.

    Thanks in advance for your help,

    Peter.

    Hi Peter,.

    You must add a line to the inside_access_in access list:

    Enable

    conf t

    access-list inside_access_in allow icmp a whole

    output

    write members

    Kind regards

    Cathy

  • VPN remote access - no network connectivity internal!

    Hi Experts,

    I understand that it is a very common problem when considering the implementations of IPSec VPN for remote access using Cisco VPN Client. But for the last six months, I have tried to configure remote VPN access to as many sites customer and gets stuck to the top with the same question!

    -The remote VPN Client connects, authenticates successfully to the local user database (to make things easier, I used the local user authentication), the tunnel is set up (I could see the exit of the isakmp #show her as a AM_ACTIVE ). So I think that the parameters of encryption and authentication for Phase 1 /Phase 2 should work because the tunnel is having successfully established

    -Now comes the question, no connectivity to the internal network. I tried all the possible solutions, that I could find online.

    1. the most common problem is NAT - Traversal not active

    -Compatible NAT - T with the time default keepalive of 20

    2. None of the configurations NAT to exempt remote VPN traffic

    -A ensured that Nat configurations not present in configuration and internal network 192.168.1.X VPN traffic networks VPN 192.168.5.X /192.168.10.X being exempted NAT

    3-Split tunnel configurations

    -Reconfigured Split tunnel access list configuration Standard access list expanded (although not required as a Standard access list is more than enouugh, if I'm not mistaken) to allow traffic selected from 192.168.1.X for 192.168.5.X/192.168.10.X that will create routes on Client that allows users to simultaneously access VPN resources and access Internet VPN client. The Tunnel from Split network group was added again to the group policy.

    4 enabled Perfect Forward Secrecy (PFS) /Disabled

    . It may be an extra charge, it has been disabled / enabled

    5. the road opposite Injection

    -Ensured that a temporary reverse route has been injected to the routing table by allowing the reverse Route Injection to insert automatically the temporary static routes to the remote tunnel using the command set reverse road networks

    A few more interesting things were noted:

    Encrypted and Bypassed packages found when a continuous ping started the ASA inside the interface.

    No decryption happens of the VPN Client, which means that there is no answer back from the network traffic statistics.

    Decryption and packages are found be increasing when I try to ping of the IP address to the customer (192.168.0.10) has published the SAA. But on the SAA, I'm not back any response and showing as? . So that would mean that there is communication of ASA to the customer via the VPN tunnel while no communication is happening from the internal network to the customer

    The entire configuration is shown below

    ASA Version 8.2 (1)
    !
    ciscoasa hostname
    activate the encrypted password of AS3P3A8i0l6.JxwD
    2KFQnbNIdI.2KYOU encrypted passwd
    names of
    !
    interface Vlan1
    nameif inside
    security-level 100
    IP 192.168.1.1 255.255.255.0
    !
    interface Vlan2
    nameif outside
    security-level 0
    address IP X.X.X.X 255.255.255.0
    !
    interface Ethernet0/0
    switchport access vlan 2
    !
    interface Ethernet0/1
    !
    interface Ethernet0/2
    !
    interface Ethernet0/3
    !
    interface Ethernet0/4
    !
    interface Ethernet0/5
    !
    interface Ethernet0/6
    !
    interface Ethernet0/7
    !
    passive FTP mode
    access-list extended SHEEP allowed ip 192.168.1.0 255.255.255.0 192.168.0.0 255.255.255.0
    ST1 list extended access permitted ip 192.168.1.0 255.255.255.0 192.168.0.0 255.255.255.0
    pager lines 24
    asdm of logging of information
    Outside 1500 MTU
    Within 1500 MTU
    IP local pool testpool 192.168.0.10 - 192.168.0.15
    ICMP unreachable rate-limit 1 burst-size 1
    don't allow no asdm history
    ARP timeout 14400
    Global 1 interface (outside)
    NAT (inside) 0 access-list SHEEP
    NAT (inside) 1 0.0.0.0 0.0.0.0
    Route outside 0.0.0.0 0.0.0.0 X.X.X.X 1
    Timeout xlate 03:00
    Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
    Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
    Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
    Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
    timeout tcp-proxy-reassembly 0:01:00
    dynamic-access-policy-registration DfltAccessPolicy
    AAA authentication enable LOCAL console
    AAA authentication http LOCAL console
    the ssh LOCAL console AAA authentication
    AAA authentication LOCAL telnet console
    Enable http server
    http 192.168.1.0 255.255.255.0 inside
    http 0.0.0.0 0.0.0.0 inside
    http 0.0.0.0 0.0.0.0 outdoors
    No snmp server location
    No snmp Server contact
    Server enable SNMP traps snmp authentication linkup, linkdown cold start
    Crypto ipsec transform-set esp-3des esp-md5-hmac FirstSet
    life crypto ipsec security association seconds 28800
    Crypto ipsec kilobytes of life - safety 4608000 association
    Crypto-map dynamic dyn1 1jeu transform-set FirstSet
    Crypto-map dynamic dyn1 1jeu reverse-road
    dynamic mymap 1 dyn1 ipsec-isakmp crypto map
    mymap outside crypto map interface
    crypto ca server
    SMTP address [email protected] / * /
    crypto ISAKMP allow outside
    crypto ISAKMP policy 1
    preshared authentication
    3des encryption
    sha hash
    Group 2
    life 43200
    Telnet timeout 5
    SSH 0.0.0.0 0.0.0.0 outdoors
    SSH 0.0.0.0 0.0.0.0 inside
    SSH timeout 5
    Console timeout 0
    dhcpd outside auto_config
    !
    dhcpd address 192.168.1.10 - 192.168.1.132 inside
    dhcpd dns 8.8.8.8 4.4.4.4 interface inside
    dhcpd allow inside
    !
    a basic threat threat detection
    Statistics-list of access threat detection
    no statistical threat detection tcp-interception
    WebVPN
    internal RAVPN group policy
    RAVPN group policy attributes
    Split-tunnel-policy tunnelspecified
    Split-tunnel-network-list value ST1
    the address value testpool pools
    dk Z6zukyDvwVjP7o24 encrypted privilege 15 password username
    sv i1gRUVsEALixX3ei encrypted password username
    tunnel-group testgroup type remote access
    tunnel-group testgroup General attributes
    address testpool pool
    Group Policy - by default-RAVPN
    testgroup group tunnel ipsec-attributes
    pre-shared-key *.
    !
    class-map inspection_default
    match default-inspection-traffic
    !
    !
    type of policy-card inspect dns preset_dns_map
    parameters
    message-length maximum 512
    Policy-map global_policy
    class inspection_default
    inspect the preset_dns_map dns
    inspect the ftp
    inspect h323 h225
    inspect the h323 ras
    inspect the rsh
    inspect the rtsp
    inspect esmtp
    inspect sqlnet
    inspect the skinny
    inspect sunrpc
    inspect xdmcp
    inspect the sip
    inspect the netbios
    inspect the tftp
    !
    global service-policy global_policy
    context of prompt hostname
    Cryptochecksum:48f0863a70b8f382c7b71db0b88620fe
    : end

    ----

    Could you please help me identify where I'm going wrong. Its been a long time I have trying to figure out but nothing seems to work! ;-(

    Help, please!

    Thank you

    ANUP

    (1) pls replace the tunnel ACL ACL standard split as follows:

    no extended ST1 192.168.1.0 ip access list allow 255.255.255.0 192.168.0.0 255.255.255.0

    access-list allowed ST1 192.168.1.0 255.255.255.0

    (2) add icmp inspection:

    Policy-map global_policy

    class inspection_default

    inspect the icmp

    (3) Finally, I add the following so that you can test the ASA inside the interface:

    management-access inside

  • Files shared via PPTP VPN remote access/desktop

    Hello

    I just bought the RV180W so I can connect to my desktop wherever you are a VPN client. The two things I need to do while I'm connected like a VPN client must be able to access my files on my desktop and be able to remote desktop as well. I have Win7 on all my computers. Ideally, I would like to do on the PPTP VPN connection, but if this is not possible so I can try out the software Cisco QuickVPN.

    I activated the PPTP on my router and created a user account. I was also able to successfully establish the remote connection. While I was logged as a PPTP VPN client, I was able to access the Internet and my configuration page of the router, which tells me that the connection is good. However, I was not able to discover my desktop label my network PC in Win7 and I was able to remote desktop. I keep my desktop PC on all the time and he will never sleep. I haven't created any strategy of connection, but maybe that's the problem. Please let me know if you know a solution.

    Thank you!

    Mustafa greetings,

    Thanks for writing.

    Have you access the router configuration using the public IP address or local IP address when you are connected to the PPTP tunnel? You can test the tunnel connecting and then ping the local IP address of the router or a computer.

    You want to make sure that the addresses that you configure for the PPTP users are not incompatible with your DHCP addresses. You need not configure any policy with PPTP.

    In addition, in order to access files through the tunnel, you must map the drive by using the IP address. For example, \\192.168.1.101\MyFiles

    Once we verify your tunnel, access issues can be troubleshooted. If you have any problems, consider giving us a call at 1-866-606-1866. We will be happy to help you.

    Kind regards

    -David Aguilar

    Cisco Small Business Support Center

    1-866-606-1866

  • ASA 5505 VPN remote access

    Hi all

    I read the http://www.cisco.com/en/US/docs/security/asa/asa80/getting_started/asa5505/quick/guide/rem_acc.html and following the steps to create a remote access VPN. At the end of this post is delivered to the FW config.

    I test the connection on a Cisco VPN Client for Windows Remote with plans on the migration of the profile to my Linux laptop. What I see is an error message when you run 'debug cryptop isa 129' of

    Dec 09 10:10:03 [IKEv1]: Group = DefaultRAGroup, IP = 83.109.134.21, Removing peer to peer table does not, no match!
    Dec 09 10:10:03 [IKEv1]: Group = DefaultRAGroup, IP = 83.109.134.21, error: cannot delete PeerTblEntry

    What seems strange to me, is that I have a group policy and a configured connection IPSec 'RemoteHome' profile, but it is not referenced in the debug output. I searched through my config for DefaultRAGroup, but nothing helped. However I found it in the ASDM under IPSec connection profiles.

    I configured the FW to use LOCAL authentication and have configured the VPN Client with the right user name and password.

    So, basically, I'm at a loss on how to correct my mistake. Any help much appreciated.

    After the config FW is the power output of debug crypto isa 129.

    See you soon,.

    Conor

    RemoteHome_splitTunnelAcl list standard access allowed host 10.2.2.2
    RemoteHome_splitTunnelAcl list standard access allowed 172.16.0.0 255.255.0.0
    RemoteHome_splitTunnelAcl standard access list allow 10.3.3.0 255.255.255.0
    RemoteHome_splitTunnelAcl list standard access allowed 192.168.2.0 255.255.255.0
    access-list 1 permit line INSIDE_nat0_outbound extended ip host 10.2.2.2 192.168.2.64 255.255.255.192
    allowed to Access - list INSIDE_nat0_outbound line 2 extended ip 172.16.0.0 255.255.0.0 192.168.2.64 255.255.255.192
    permit for access list 3 INSIDE_nat0_outbound line scope ip 10.3.3.0 255.255.255.0 192.168.2.64 255.255.255.192
    allowed to Access - list INSIDE_nat0_outbound line 4 extended ip 192.168.2.0 255.255.255.0 192.168.2.64 255.255.255.192
    local pool VPN_REMOTE_POOL 192.168.2.90 - 192.168.2.99 255.255.255.0 IP mask
    internal RemoteHome group strategy
    Group Policy attributes RemoteHome
    Protocol-tunnel-VPN IPSec
    Split-tunnel-policy tunnelspecified
    value of Split-tunnel-network-list RemoteHome_splitTunnelAcl
    value of DNS server *.
    cunningtek.com value by default-field
    tunnel-group RemoteHome type remote access
    attributes global-tunnel-group RemoteHome
    Group Policy - by default-RemoteHome
    address VPN_REMOTE_POOL pool
    IPSec-attributes tunnel-group RemoteHome
    pre-shared key *.
    Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
    NAT (INSIDE) 0 access-list INSIDE_nat0_outbound tcp udp 0 0 0

    Firewall # Dec 09 10:10:03 [IKEv1]: IP = 83.109.134.21, IKE_DECODE RECEIPT Message (msgid = 0) with payloads: HDR (4) SA (1) + KE + NUNCIO (10) + ID (5) the SELLER (13) + the SELLER (13) + SOLD
    OR (13) of the SELLER (13) + the SELLER (13) + (0) NONE total length: 849
    Dec 09 10:10:03 [IKEv1 DEBUG]: IP = 83.109.134.21, SA payload processing
    Dec 09 10:10:03 [IKEv1 DEBUG]: IP = 83.109.134.21, processing ke payload
    Dec 09 10:10:03 [IKEv1 DEBUG]: IP = 83.109.134.21, payload processing ISA_KE
    Dec 09 10:10:03 [IKEv1 DEBUG]: IP = 83.109.134.21, nonce payload processing
    Dec 09 10:10:03 [IKEv1 DEBUG]: IP = 83.109.134.21, payload processing ID
    Dec 09 10:10:03 [IKEv1 DEBUG]: IP = 83.109.134.21, payload processing VID
    Dec 09 10:10:03 [IKEv1 DEBUG]: IP = 83.109.134.21, received xauth V6 VID
    Dec 09 10:10:03 [IKEv1 DEBUG]: IP = 83.109.134.21, payload processing VID
    Dec 09 10:10:03 [IKEv1 DEBUG]: IP = 83.109.134.21, DPD received VID
    Dec 09 10:10:03 [IKEv1 DEBUG]: IP = 83.109.134.21, payload processing VID
    Dec 09 10:10:03 [IKEv1 DEBUG]: IP = 83.109.134.21, received Fragmentation VID
    Dec 09 10:10:03 [IKEv1 DEBUG]: IP = 83.109.134.21, IKE Peer included IKE fragmentation capability flags: Main Mode: real aggressive Mode: false
    Dec 09 10:10:03 [IKEv1 DEBUG]: IP = 83.109.134.21, payload processing VID
    Dec 09 10:10:03 [IKEv1 DEBUG]: IP = 83.109.134.21, received NAT-Traversal worm 02 VID
    Dec 09 10:10:03 [IKEv1 DEBUG]: IP = 83.109.134.21, payload processing VID
    Dec 09 10:10:03 [IKEv1 DEBUG]: IP = 83.109.134.21, the customer has received Cisco Unity VID
    Dec 09 10:10:03 [IKEv1]: IP = 83.109.134.21, message received ISAKMP Aggressive Mode 1 with the name of Group of unknown tunnel "conor".
    Dec 09 10:10:03 [IKEv1 DEBUG]: Group = DefaultRAGroup, IP = 83.109.134.21, IKE SA payload processing
    Dec 09 10:10:03 [IKEv1 DEBUG]: Group = DefaultRAGroup, IP = 83.109.134.21, IKE SA proposal # 1, transform # 5 entry overall IKE acceptable matches # 1
    Dec 09 10:10:03 [IKEv1 DEBUG]: Group = DefaultRAGroup, IP = 83.109.134.21, build the payloads of ISAKMP security
    Dec 09 10:10:03 [IKEv1 DEBUG]: Group = DefaultRAGroup, IP = 83.109.134.21, building ke payload
    Dec 09 10:10:03 [IKEv1 DEBUG]: Group = DefaultRAGroup, IP = 83.109.134.21, building nonce payload
    Dec 09 10:10:03 [IKEv1 DEBUG]: Group = DefaultRAGroup, IP = 83.109.134.21, Generating keys for answering machine...
    Dec 09 10:10:03 [IKEv1 DEBUG]: Group = DefaultRAGroup, IP = 83.109.134.21, construction of payload ID
    Dec 09 10:10:03 [IKEv1 DEBUG]: Group = DefaultRAGroup, IP = 83.109.134.21, build payloads of hash
    Dec 09 10:10:03 [IKEv1 DEBUG]: Group = DefaultRAGroup, IP = 83.109.134.21, calculation of hash for ISAKMP
    Dec 09 10:10:03 [IKEv1 DEBUG]: Group = DefaultRAGroup, IP = 83.109.134.21, build payloads of Cisco Unity VID
    Dec 09 10:10:03 [IKEv1 DEBUG]: Group = DefaultRAGroup, IP = 83.109.134.21, constructing payload V6 VID xauth
    Dec 09 10:10:03 [IKEv1 DEBUG]: Group = DefaultRAGroup, IP = 83.109.134.21, constructing the payload of the NAT-Traversal VID ver 02
    Dec 09 10:10:03 [IKEv1 DEBUG]: Group = DefaultRAGroup, IP = 83.109.134.21, NAT-discovery payload construction
    Dec 09 10:10:03 [IKEv1 DEBUG]: Group = DefaultRAGroup, IP = 83.109.134.21, NAT discovery hash calculation
    Dec 09 10:10:03 [IKEv1 DEBUG]: Group = DefaultRAGroup, IP = 83.109.134.21, NAT-discovery payload construction
    Dec 09 10:10:03 [IKEv1 DEBUG]: Group = DefaultRAGroup, IP = 83.109.134.21, NAT discovery hash calculation
    Dec 09 10:10:03 [IKEv1 DEBUG]: Group = DefaultRAGroup, IP = 83.109.134.21, construction of Fragmentation VID + load useful functionality
    Dec 09 10:10:03 [IKEv1 DEBUG]: Group = DefaultRAGroup, IP = 83.109.134.21, build payloads VID
    Dec 09 10:10:03 [IKEv1 DEBUG]: Group = DefaultRAGroup, IP = 83.109.134.21, Send Altiga/Cisco VPN3000/Cisco ASA GW VID
    Dec 09 10:10:03 [IKEv1]: IP = 83.109.134.21, IKE_DECODE SEND Message (msgid = 0) with payloads: HDR (4) SA (1) + KE + NUNCIO (10) + ID (5) + HASH (8) the SELLER (13) + the SELLER (13) + SOLD
    OR (13) NAT - D (130) + NAT - D (130) of the SELLER (13) + the seller (13) + (0) NONE total length: 424
    Dec 09 10:10:03 [IKEv1 DEBUG]: Group = DefaultRAGroup, IP = 83.109.134.21, case of mistaken IKE AM Responder WSF (struct & 0xd8d3bed8) , : AM_DONE, EV_ERROR--> AM_SND_MSG2, EV_
    SND_MSG--> AM_SND_MSG2, EV_START_TMR--> AM_BLD_MSG2, EV_BLD_MSG2_TRL--> AM_BLD_MSG2, EV_SKEYID_OK--> AM_BLD_MSG2, NullEvent--> AM_BLD_MSG2, EV_GEN_SKEYID--> AM_BLD_MSG2, EV_BLD_MSG2_HDR
    Dec 09 10:10:03 [IKEv1 DEBUG]: Group = DefaultRAGroup, IP = 83.109.134.21, IKE SA AM:7ff48db9 ending: 0x0104c001, refcnt flags 0, tuncnt 0
    Dec 09 10:10:03 [IKEv1 DEBUG]: Group = DefaultRAGroup, IP = 83.109.134.21, sending clear/delete with the message of reason
    Dec 09 10:10:03 [IKEv1]: Group = DefaultRAGroup, IP = 83.109.134.21, Removing peer to peer table does not, no match!
    Dec 09 10:10:03 [IKEv1]: Group = DefaultRAGroup, IP = 83.109.134.21, error: cannot delete PeerTblEntry

    I think this is the beginning of your question.

    Message received ISAKMP aggressive Mode 1 with the name of the unknown group tunnel "conor".

    In the vpn client, you must enter the name of the group, RemoteHome and pre shared key, NOT your username. You will be asked your username after login.

    As the name conor group does not exist, it is failing in the DefaultRAGroup

Maybe you are looking for

  • updates

    I just upgraded to os os 10.11 10.7. Updates of applications is now it seems that in the app store. I can't understand how to choose which applications to automatically check updates for and which not. So, where do you do that?

  • Windows 2000 message user32.dll

    I installed windows 2000 as second operating system.Now, at the start, I get the message "enter PadExe.exe point niet anyway."What this mean, how do I get off of him?

  • Identifying word password does not not with app store

    Hi guys,. odd question here. I tried to update an application but he told me that my password is incorrect. I know it's not because I'm registered in "my apple id" with her without any problem but when I tried the app store yet once I thought he was

  • HP CP400DN: CP4005dn

    He is a recent problem insofar as my printer worked OK until about 3 weeks ago. When trying to print multiple pages, him buzzing printer in action prints one page front and then stops with the display reading "Clearing paper path" followed by "check

  • Locking with memory dump or sometimes freezes just and need to hard reboot. The 7th

    Hello No specific program causes, I can load the system a few days and it blocks when its idle sometimes very sporadic. This is error code; Unknown bug control: the 7th. Parameters = 0xc0000005, 0x482ec466,.0x80e49814, 0x80e493f0. Thanks in advance!