the H200 controller replacement

Similar Questions

• The PERC S300 controller replacement

  I want to upgrade a server PowerEdge R310 Windows Server 2008 R2 to R2 2012. Unfortunately the PERC S300 is not supported and I could not find the necessary drivers.

  I found that PERC H700 has the correct drivers and is compatible with the R310, can anyone confirm that please?

  Are there cheaper alternatives? Otherwise, I think I have to disconnect the PERC controller and connect the drives to the internal SATA ports, but then I have 4 independent drives with no RAID either because the PERC S100 embedded is not as well supported... (is there a SW raid solution?)

  Thank you

  The H700 is a controller that is supported on the R310, but you must do a clean install or backup/restore.

  The H310 is also supported by the R310.  It is a hardware RAID controller low end and would also require a reinstall/restore.

  The S100 can handle a direct migration of the S300 disc, but when you read, it is not supported in 2012 either.

  You can move the disks to the SATA onboard and get rid of the S300, but there was also a clean installation/restore.  If you did the onboard SATA (in AHCI/no RAID), there was no RAID managed by the system, but you can configure RAID under Windows, which would provide at least some redundancy.  Performance is not worse than the S series controllers.

  My advice?  Never skimp on storage, no matter what it is used for.  Always get the top of the page (H7x0) controller when you configure a server.

• Satellite Pro M70 - ist is possible to change the craphics controller?

  Is it possible to change the graphics controller to my Satellite Pro M70...
  If so, where to buy a new one?

  THX

  Hello

  Well, in general it s is not possible to replace or update the graphics card.
  But I compared a Satellite Pro M70 unit because this series of laptop was delivered with different hardware configurations and I found that these installed graphics cards:
  Mobile Intel 915GM Express Chipset AlvisoGM 8 MB to 128 MB shared video memory
  ATI MOBILITY RADEON X600SE 128 MB of video memory
  ATI MOBILITY RADEON X 700 256 MB of video memory

  However, in my opinion you can not change the graphics card

• Problem of update for the onboard Controller 1.03 T43 (1871)

  Hello

  I have a T43 (1871) and is not able to update the controller shipped (1.03). I tried to update to 1.04 & 1.05 without success.

  However, I could update the BIOS to 1.29 with THIS 1.03.

  How to replace the standard HD with a Hitachi HTE721060G9AT00 and received the 2010 error. Have heard unofficial BIOS that does not MISTAKE 2010.

  One way or the other I like update the embedded controller.

  TIA!

  I found a way to update the controller shipped from my T43 (1871).

  The help of the update of the system Thankvantage, or no version diskkette updated on http://support.lenovo.com/us/en/products/laptops-and-netbooks/thinkpad-t-series-laptops/thinkpad-t43...

  But

  Click START > RUN, and enter name of file with the name of the full path where you stored Embedded Controller program Update Utility with s - a-s options. (eg. C:\Temp\1YHJ05US. EXE s - a - s)
  Then press the Enter key. Windows automatically stops and the program of the system BIOS update without any user intervention.

  As I found on http://forum.thinkpads.com/viewtopic.php?f=2&t=23331by chriswendy (posted: Wednesday, April 12, 2006 17:00).

  EC, updated today at 1.05 through switches s - a s

• Aurora R4: newly installed SSD running in G2 / SATA300 - how can I 'persuade' the SATA controller to run at G3 /SATA600?

  Good evening.  I was a little indecisive on the place where this post, but I think it's the right place.

  I just replaced the main drive in my Alienware Aurora R4 with a SanDisk Extreme Pro SSD... works perfectly (and quickly).  I realized a clean Windows 10 Pro (x 64), generation to level to the latest version.  I'm not using RAID.

  The SDS is properly installed and connected in the location SATA01.

  This Aurora R4 has the "Dell", well actually "Intel" Patsburg 6 Port SATA AHCI Controller (revised A7), capable of handling G3 / SATA600.  However, two DVD players work to G1 / SATA150 and all four disks are running at G2 / SATA300.

  I have the latest driver for the Intel Rapid Storage Technology technology, confirming a transfer rate SATA 3 Gb/s for my SSD (and the other three HARD drives).

  How can I convince the computer I want to optimize my SanDisk Extreme Pro SSD performance, with the rate of transfer running at G3 / SATA600?

  I searched on through the value of the library of web pages, but not found a solution.  I was hoping that it would be a BIOS problem (installed last), is a question of the SATA controller firmware, but that doesn't seem to be the case.  Technology Intel Rapid Storage Technology driver allows no fiddling, so I drew a blank there.

  Knowledge advice would be warmly received, especially if you have a R4 Aurora that runs a G3 SSD / SATA600!

  Hi Domo_P1000,

  You can search the forums to Alienware for help with this. I found this relevant thread.

• migration of APs to the 5508 controller 4402

  Hello all,.

  We have two controllers (4402 and 5508) to one of the site.

  Customers of services at present.

  Both controllers have the same set of SSID but uses only a single group of AP.

  What would be the best means to move APs on 4402 to 5508?

  4402 services series years 1230 and 1240 AP. And looking at the note accompanying the WLC 7.6 code located on 5508,

  years 1240 only are supported. So, we will need to get the replacement of the years 1230.

  Someone suggested to go into every single years 1240 and change high availability for point to 5508 as primary and secondary 4402

  (just in case the AP don't is not the controller) 5508 Once this is done, I can add the AP in the access point default of the group to broadcase the same SSID.

  Is it enough for the task of migration?

  Also, what is the requirement of default design for the number of necessary uplinks?

  We have about 150 APs currently on 5508 that uses Group LAG of 1 4 uplinks.

  Regarding the 4402, it is service 60 APs with 1 2 uplinks.

  Thus with the APs on 4408 joining the 5508, 5508 serves about 210APs. 4 1 enough uplink is?

  What is the best practice recommended requirement of uplink AP?  APs on 5508 are 3602 s and 3702 s.

  Thank you in advance.

  P.S. BTW two controllers are part of the same mobility group

   Someone suggested going into every single 1240s and change the high availability to point to 5508 as primary and 4402 as secondary.(just in case the AP does not join the 5508 controller.) Once that is done, I can add the AP into the default AP group to broadcase the same SSIDs.Is that enough for migration task?

  Yes, it is sufficient. Unless 5508 have the same available on 4402 AP group name, all years 1240 migration goes into default-group & you may need to add to the good group of AP. It is advisable to have same AP group created between the controllers where AP configured for failover.

  Don't forget 1240 last took in charge in 8.0.x code. In order to better plan as well before moving on to 8.1 replacement code (expect less than 1-2 months of time). See below for more details compatibility matrix

  http://www.Cisco.com/c/en/us/TD/docs/wireless/compatibility/matrix/compatibility-matrix.html

   Also what is the default design requirement for the number of uplinks needed? We have about 150 APs currently on 5508 which uses LAG group of 4 1G uplinks.Thus with APs on 4408 joining the 5508, 5508 will roughly serve 210APs. is 4 1G uplink sufficient? 

  4G LAG is more that sufficient for 250 AP, I'm sure that together the traffic will be much less of 4G if monitor you the traffic volume of the art on this trunk links.

   What is the best practice recommended AP to uplink requirement? APs on 5508 are 3602s and 3702s.

  I guess that all of these AP connected to 1 Gbps switch compatible PoE ports +. If your binding rising intercommutation is 1 Gbit/s, which would be the bottleneck, WLC to SW LAG before becoming a bottleneck.

  HTH

  Rasika

  Pls note all useful responses *.

• failure of the graphics controller envy14t-1000 flashes code?

  For laptop of HP Envy 14-1000. i5 - 450 M, Radeon 5650 M. Out of warranty. New installation of Windows 8 Professional on an OCZ Agility SSD 4.

  At startup, caps lock flashes code indicates a failure of the graphics controller. Stays on for 2-5 minutes, but will then start Windows. This indicates imminent failure and a replacement motherboard is necessary, or is it the result of something else?

  On your laptop, there are several codes of different flashing given by a flashing caps lock key. You say that it is the graphical model controller failure error light. Use this document to make sure it is the correct error code.

  The ENVY of laptops series have their GPU soldered onto the motherboard. So if you've got a controller failure graphics card you might have to replace the entire motherboard of the laptop. This interview is possible to do it yourself, although difficult. Even if you specify your product is out of warranty, I suggest to contact HP Technical Support again and look in an interview of the laptop. If you are in the USA / Canada, you can contact HP at 1-800-474-6836. If you are outside the United States / Canada then here try to find contact information for your region.

• Remove the SCSI controller change question of VMWare

  Hello

  I used PowerCLI for create a virtual machine and replace it with instead of buslogic SCSI LSILogic controller. I did it by using the following code:

  function updateSCSIController ($vmName, $ctrlName)

  {

  $vm = get - VM $vmName | Get-View

  1. Get the controller and devices on

  $vm. Config.Hardware.Device | where {$_.} DeviceInfo.Label - eq $ctrlName} | % {

  $oldCtrl = $_

  $ctrlKey = $_. Key

  $devs = @)

  $_. Device | % {

  $devKey = $_

  $vm. Config.Hardware.Device | where {$_.} Key - eq $devKey} | % {

  $devs += $_

  }

  }

  }

  1. Create the specification for the device changes

  $bootDelay = 10000

  $spec = new-Object VMware.Vim.VirtualMachineConfigSpec

  $spec. BootOptions = New-Object VMware.Vim.VirtualMachineBootOptions

  $spec. BootOptions.BootDelay = $bootDelay

  1. Remove the old controller

  $old = new-Object VMware.Vim.VirtualDeviceConfigSpec

  $old.device = $oldCtrl

  $old.operation = 'delete '.

  $spec. DeviceChange += $old

  1. Update the devices connected to the controller

  $devs | % {

  $dev = new-Object VMware.Vim.VirtualDeviceConfigSpec

  $dev.device = $_

  $dev.device.ControllerKey = - 100

  $dev.operation = "Edit."

  $spec. DeviceChange += $dev

  }

  1. Add the new controller

  $new = new-Object VMware.Vim.VirtualDeviceConfigSpec

  $new. Device = New-Object VMware.Vim.VirtualLsiLogicController

  $new. Device.Key = - 100

  $new. Device.ControllerKey = $oldCtrl.ControllerKey

  $new. Device.UnitNumber = $oldCtrl.UnitNumber

  $new.operation = 'Add '.

  $spec. DeviceChange += $new

  $vm. ReconfigVM ($spec)

  }

  However when I try to start the virtual machine Via code, it gives me an error saying that the virtual machine has questions to be decided.

  This is the question asked by VMWare:

  sg.disk.AdapterMismatch: the disk attached to the node SCSI0:0 has been created for the Buslogic SCSI adapter but SCSI0 Virtual Machine device is a SCSI LSI Logic card.

  VMware ESX Server can change the free disc adapter type. Attention of the user, if a guest operating system is installed on the drive, it is perhaps not able to start.

  Do you think Vmware ESX Server to change the type of adapter for SCSI0:0 disk

  This issue can be removed through PowerCLI?

  This is the part of code that fails

  updateSCSIController - vmName $name - ctrlName "SCSI controller 0.

  Start-VM - $vm VM - confirm: $false

  $vm | Get-CDDrive. Game-CDDrive-connected: $true - confirm: $false

  I don't know if you can remove the question, but you can respond with the Set-VMQuestion cmdlet.

  ____________

  Blog: LucD notes

  Twitter: lucd22

• Failure of hard drive in Dimension 8250, the maximum size and the type of replacement tips please

  Dimension 8250 (Feb 2003), Windows XP Home SP2, 60 GB HDD, 512 MB of RAM, BIOS A01 - entirely standard

  My hardrive suffers from weird deaf noise for a few months, but last week, it was a lot worse. Sometimes it starts up and is ok, othertimes it takes 1 hour to start and everything produces the deaf noise and is so slow, that it's unusable and other times simply clunks and not even start.

  Error messages received:

  (a) "drive Dell, monitoring system has detected that drive 0 on the primary Eide controller is out of normal, backup specifications and replace the HARD drive.

  (b) "error was detetcted on the HARD disk during the paging operation" (in the event viewer)

  (c) "driver detetcted a controller the HARD disk error" (in the event viewer)

  (d) when I run the Dell IDE Drive Diagnostics (F12), it says FAILED return Code 6

  Issues related to the:

  (1) am I correct that the drive needs replacement?

  (2) I want to just keep it very simple and buy a drive and adapt it, do not worry about BIOS or other upgrades. What I do pay attention to the size car that I buy, is there a maximum size that I can have with BIOS A01? Maybe thought to 120 GB? I just want to be able to adapt, without having to play around with BIOS upgrades so simply the easiest option, which is to buy, set up and reinstall the software. So, is there any limitation integrated with BIOS A01? The recovery CD is XP SP 1

  (3) am I correct that the PC supports up to 100 ATA if you need to make sure that I buy ATA 100 no ATA 133?

  (4) original drive is Hitachi, Seagate Barracuda would be better?

  (5) think active drive a 2 MB cache, a cache 8 MB drive would work ok without me having to pay anything and if yes is it useful on the 2 MB cache?

  Thanks for your time.

  Message edited by craiguk on 02/06/2008 18:27
  Message edited by craiguk on 02/06/2008 18:28
  Message edited by craiguk on 02/06/2008 18:47
  
  

• If my Macbook Pro is under Applecare extended it reduces the cost of replacing the battery?

  If my Macbook Pro is under Applecare extended it reduces the cost of replacing the battery?

  How much is usually charged for the replacement of the battery?   (in the United Kingdom)

  Thank you

  If it's a warranty or Apple Care + the covered replacement instance, it should be free.

  Otherwise:

  Mac Service Pricing - Support Apple laptops

  https://support.Apple.com/en-GB/Mac-notebooks/repair/service/pricing

  13/15 inch MacBook Pro

  £99 INCLUDING VAT.

• My ink carriage does not move to the way to replace the ink cartridges. I think I put the ink in the wrong office

  My ink carriage does not move to the way to replace the ink cartridges. I think I put ink in bad officejet 3830

  Hello! Welcome to the community @Tammy111 HP

  I read your post about the ink carriage being stuck in your Officejet 3830, and I wanted to respond to troubleshoot. Try these steps and if the transport is not yet move to order so that you can access the ink, then your best bet would be to call phone support to see if they can replace the unit for you. I'll leave their details below.

  HP OfficeJet 3830, DeskJet 3830, 5730 printers - an error 'Transport Jam'

  Click on the thumb to below testify my help!

  Click on the "accept as Solution" if I'm you guide to a solution!

  Contact HP:

  Step 1. Open the link: www.hp.com/contacthp/

  Step 2. Enter the product number or select Auto detection

  Step 3. Scroll up to "still need help? Fill out the form to select your contact options.

  Step 4. Scroll down and click on: contact HP options - click Get phone number

  File number and phone number appear

• A friend changed my wallpaper of girls on his iPad mini and now we do not find the photo to replace? Any ideas?

  I hope someone can help as a friend changed my 4 years girls wallpaper on his iPad Mini and now we do not find the photo to replace? I thought that it would be in his photographs, but this isn't? Help! She is not happy...

  Was it a personal photo or one of the built-in wallpapers?

• Satellite 2710 XDVD: the graphics controller hardware specification

  Can someone tell me about specific electrical equipment of the graphics controller (manufacturer, type, etc.)?
  And what kind of changes are in the BIOS version 7.60?
  Can I install more than 192 MB of RAM?

  Thank you very much

  Post edited by: philips

  Hello

  in the specification of this machine, I found that there a Trident Microsystems Cyber 9525 graphics card.
  And he says that the laptop can not use more than 192 MB of RAM.

  Good bye

• World for the voluntary battery replacement program

  Hello. I am concerned about the voluntary battery replacement.

  My laptop is: Tecra S3, manufactured at 2006-02-21 (ordered in 2006-03-14). Model number is: PTS30E-01R01CG3. I tried the software for testing, but he said that I'm not concerned. Eight days latter, I saw this new article (http://eu.computers.toshiba-europe.com/cgi-bin/ToshibaCSG/news_article.jsp?service=EU&ID=Battery_Pack_Replac ement_09_2006 & cnt = NEWS & key = Battery_Pack_Replacemen t_09_2006 & display = T) and I definitely want to participate.

  Before a few weeks, I noticed that my battery wear level is 17%, which is not normal (never checked to see what is the initial value was), because from the beginning, I used to follow the instructions for the use of battery of security!
  I am from Bulgaria and I would like to know if I can replace my battery.

  Thank you.

  [Edited by: admin on October 4, 2006 09:10]

  Hello

  To my knowledge, the warranty will cover battery for one year.
  In my opinion it should be no problem with the battery replacement if the warranty is valid.
  In this case, contact the Toshiba service partner in your country and ask for help.

  By the way: as Sam mentioned in the post above only are not all but only some notebooks between March and may was affected and there could be only one problem with the loading and unloading of procedure.

• Satellite C660-117 - where to download the Ethernet controller driver?

  Hello.

  Can someone please help with my laptop? Here's my laptop specs:
  Model: Toshiba Satellite C660-117
  Part number: PSCOLE-00Y00JEN
  Serial number: XA458343K

  I have just rewiped my laptop with Windows 7 Ultimate. I use the laptop on a wireless connection. In Device Manager, I have an exclamation mark next to the Ethernet controller. This prevents me from going online.

  Can someone direct me please the link to download some driver I need?

  Thank you much much in advance.

  Dennis.

  Hey Buddy,

  Controller driver Ethernet can be both: WLAN or LAN card. All the drivers and tools can be downloaded from the official website of Toshiba:
  http://EU.computers.Toshiba-Europe.com > support & downloads > download drivers

  You have installed Windows 7 Ultimate, but may I ask why you haven t used the Toshiba with Windows 7 Home Premium recovery disc? On this disc are all the drivers and tools are installed because it s a picture of factory for you don t have stress with driver and installation tool.