The speech unit cut in mid-sentence users

Similar Questions

• Read the motor current by using the controller PXI-7350 and MID-7604

  I use the PXI-7350 controller and MID-7604 drive to run a motor drive.  I would like to be able to measure the motor current while moving the engines.  This measurement is possible?  If so, what commands are required to read the motor current?

  Hi Casey,.

  the 7604 can limit the current to a value that is selectable by the user and you can activate the current reduction if the axis is stopped, but there is no way to read the current engine. If you want to measure the motor current, you must do it with an external device, but due to the current chopping and multiphase, motor control stepper motors is not a trivial task. Micro step mode the current phase looks like a rough sinus with lots of harmonics signal, so you will need to do a true measure requiring RMS of expensive measurement equipment.

  Anyway. If you need to know the temperature of the motor you should better measure the temperature directly. The most inexpensive device OR do is the NI USB-TC01, but there are many other options available.

  Kind regards

  Jochen

• restart of the computer from standby when I press start on the system unit, but not when a scheduled task is started

  Windows XP Professional SP3, updates, motherboard Asus P4P800 series (2006). The original system dates back to 2002, but there have been many additions and replacement upgrade. More recently, 2011, two old hard drives have been replaced (XP had destroyed itself requiring a reinstallation), with a much larger and HD, and the cpu has been replaced by a 3 GHz one.

  I've configured the BIOS to enable the use of standby mode (standby). I wanted to be able to run scheduled backup jobs early in the morning, a little before I wake up normally. The goal was to conserve energy. Whenever I leave the computer for more than an hour or two, I put it in sleep mode. In recent years, that it worked well.

  Scheduled tasks are still, in fact, more surely than ever. But now, when I press the Start button on the system unit, the operating system is restarted rather than restore the State of the system at the time of Eve. This happened almost constantly for maybe a week. I was always a guard never enter sleep mode when I'm aware of any application running who has not completed a requested operation (save a file, defragment a disk, etc.).

  I searched on the basis of knowledge, but not found any problems like that. There has been no hardware changes, no new devices; only change of important software (but it is difficult to see how it might be relevant) was the resettlement of Java Runtime Environment 6.x to support the help of OpenOffice. Although I have not checked, I am reasonably sure that all drivers are up-to-date.

  No idea why this should suddenly become a problem or how to fix?

  Hello

  I suggest you follow these methods and check.

  Method 1: View the steps suggested in the following link.

  How to solve the problems of hibernation and standby in Windows XP

  http://support.Microsoft.com/kb/907477

  Method 2: Use the Powercfg.exe utility to restore the default power mode

  You can use the Powercfg.exe utility to copy the power mode of the user by default to the currently logged user profile. You can do this because eating patterns are only related to individual user accounts. To copy the default user schema using the Powercfg.exe utility, follow these steps:

  1. click on Start, click run, type cmdand then click OK.

  2. at the command prompt, type the following command and press ENTER:
  powercfg /RestoreDefaultPolicies

  Method 3: How to perform the check and clean boot if the problem persists.

  http://support.Microsoft.com/kb/310353

  NOTE: Once you check the functionality, follow the suggestions under steps to configure Windows to use a Normal startup state.

  I hope this helps!

• Disable the copy or cut and paste completely

  From: kend_beledm

  Is it possible on a windows-based systems to disable or completely disable the copy and paste function, any type of program is displayed on the screen.

  De : Andrew McLaren

  You can do this for Windows as a whole (and even if you did, users could simply use a print-screen instead, limited data). But you can do it for specific applications: essential technology is Windows Rights Management Services ("RMS"). See http://www.microsoft.com/windowsserver2003/technologies/rightsmgmt/default.mspx

  If you have an application that can participate in a RMS infrastructure, you can indeed set up policies to selectively allow or prevent the n-cut-paste, etc., to users and groups. or refuse to cut-and - paste altogether in this application.

  Microsoft Office is the application most common which can be plugged into RMS. Once it is all together, it is extremely effective... you really want to cut-and - paste privileged information from this juicy email or a Word document. but hell, you just can not! You also cannot transfer protected emails, etc..

  There is a public SDK, so anyone can write an application that subscribes to RMS and restrict access to the application data. However if you have a legacy application (IE, an already existing application) which you can not re-engineer, so I think you're a bit stuck. You may need to address the issue of security in a non computer perspective, such as human resources policies, etc.

  You can also take a look at the Software Restriction policies ("PRS"), a similar security Windows feature. SRP will not stop users to cut and paste, as such; but it lets you create a very controlled environment. You can stop the users do a lot of things you don't want to do. See:

  http://technet2.Microsoft.com/windowsvista/en/library/0d504b1d-e57c-4DCC-8A5A-8d1da9e4d1fe1033.mspx?mfr=true

  It will be useful,

  --

  Andrew McLaren
  amclar (at) optusnet dot com dot to the

  Another response of the community of Windows Vista discussion groups

• Unable to get the basic unit of the stainless steel bracelet

  Hi, I am unable; e of pop on the basic unit of the steel stainless bracelet body. I couldn't find anything online that shows the process. In addition, can I exchange the strap metallic with leather and other straps? where can I buy these? Concerning

  Hey!

  I understand that it may be a little difficult to understand, since there are no edges or cuts to adjust to pop the base unit on. I took a few photos for you:
  
  Basically what you need to do, it's only gently but firmly push you down on the screen next to the edge to pop out. Make sure it is on the same side as the microUSB port, you recognize there is not not a small hole in the front (and a microUSB on the back port). I've marked the photo that I took with the green as to where you have to press on and red on the side that you should not press.

  Once jumped, it will look like this:
  

  Let me know if is not yet known!

  About yew, you can exchange the strap, it's quite possible. Everything just to get a different bracelet and insert the base unit. Unfortunately, I can't help where you find it as it varies depending on the market, but see if your retailer can help you in this regard!

• The Multiple Unit call manager Clusters

  Installation program:

  2 x Unit 1 x PRI 1 x dry failover servers.

  Unity 4.0.3 sr 1

  Unified on the box store. Exchange 2000 Server cluster.

  Install new 4.0.3 no upgrade, without double integration.

  UTIM

  Teaspoon 7.0.3b

  Group 1 - connect to the 1/2 Site A CM 3.3.3 CM sr4a

  1-50 answer calls only ports

  51-65 all ports.

  MWI 3300/3301

  Group 2 - connect to the CM 1 Site B CM 4.0.1 sr 1 has

  66-68 answer calls only ports

  MWI 700/701

  * Might turn not 66-68 for any service unit started using lower ports for TRAP etc.

  Group 3 - connect the CM 1 Site C cm 3.3.3 sr 2

  ThePort 69-72 answer calls only.

  MWI 700/701

  * Might turn not 66-68 for any service unit started using lower ports for TRAP etc.

  Question:

  The primary unit reported the following in the application event log:

  Event ID 1041

  Cisco Unity_Notifier

  Cannot set the lamp to wait for message for , ext XXXX, switch 0, group 2, reason: not appropriate port. Check the configuration of the port MWI.

  Same error event for all clusters/users on the same switch/cluster combination.

  MWI, notification of MSG and traps work properly.

  But the unit is still reported a problem.

  FYI: Seems to start after 1. Service release 2 has been installed. Failover was configured.

  THX.

  The unit still tries to send MWI to each cluster. If it does not you will see this error. I would say to just allowing the Message Notification on port 68 and 72. Given that the unit does not know what CCM a Subscriber is located at, it should send the MWI to each cluster. If you have at least one port for MWI, who should take care of errors.

• Addition of VSA on the GBA unit

  Dear all,

  How to add other attributes specific to the seller on the GBA unit? Normally on the software, we use the command line "CSutil" to add the ASB, but as the device is not interface to the windows system, there is no way to configure it. No one knows how to do?

  Appreciate for any idea

  Starting from 3.1, supported ACS VSA custom with RDBMS synchronization, also. This was done specifically to take charge of the unit. Action codes 350 per 355 support config and custom VSA definition.

  So, consult the ACS 3.2 user guide device for information on the use of RDBMS Synch.

  Some links:

  Topic on the RDBMS support for VSA import:

  http://www.Cisco.com/univercd/CC/TD/doc/product/access/acs_soft/csacsapp/user/sad.htm#451579

  Beginning of the RDBMS feature doc:

  http://www.Cisco.com/univercd/CC/TD/doc/product/access/acs_soft/csacsapp/user/sad.htm#451426

  Synch. Annex codes:

  http://www.Cisco.com/univercd/CC/TD/doc/product/access/acs_soft/csacsapp/user/AG.htm

  Table with the relevant action codes:

  http://www.Cisco.com/univercd/CC/TD/doc/product/access/acs_soft/csacsapp/user/AG.htm#1372

• Is windows 7 to the different United States to the United Kingdom?

  is windows 7 to the different United States to the United Kingdom?

  I know of course that we can use different dictionaries etc in software and select different keyboards, but windows is different?

  If different can you change to English from the United States to the United Kingdom using the multi-language-user pack?

  is the version of the package yet for companies (and one another) or I read that it can be installed on 7 pro SP1?

  that s 4 issues for the price of 1 - thank you very much in advance for any help

  Hello Gibbs,

  Thanks for posting your question in the Microsoft Community. We are happy to help you.

  Yes, we have specially designed Windows 7 N edition for European countries. However, you may not be able to upgrade Windows 7 to Windows 7 N.

  I suggest you have a look at the following article.

  What is a Windows 7 N edition?

  http://Windows.Microsoft.com/en-GB/Windows7/products/what-is-Windows-7-N-Edition

  You can also see the discussion on the thread below for more information.

  Windows 7 DVD disc in different countries

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-windows_install/Windows-7-DVD-disc-in-different-countries/54eb5f87-8969-4a7e-83c3-5fb16273d696

  Come back and let us know the State of the question, I'll be happy to help you. We, at tender Microsoft to excellence.

  Thank you.

• the words "how much" in any sentence will change the information contained in the typed in the field when it is selected on

  help I created a pdf form that is sent to the few hundred people very few will accept something very strange is happening when people try to fill it.  If the words are together in any sentence the field will change the information contained in the typed in when it is clicked on. If the 7 is entered in the field once on it out of the chaanges filed for view '0'.  23 or 230 happens every time.   This does not happen when if the form is opened in Adobe reader or Adobe Pro, but it seems for the most part that it opens in the browser, which is where it is filled.

  Thank you for any assistance.

  Many browsers have their own PDF plugins now that are used by default, and are unfortunately very bugs, especially when it comes to scripts and form fields. There is nothing much we can do about it, except for sending complaints to the manufacturers of these plugins and ask your users to avoid their use by saving the file and open it in Adobe Reader (or Acrobat) directly instead of inside the browser window.

  PS. the same also applies to the application overview of Apple.

• Why the DR unit does not trigger schema when it is called remotely?

  Hi all

  I have a question about the triggers of oracle schema and I would be grateful if you could kindly give me a helping hand.

  Oracle version: 11 GR 2 (11 g Enterprise Edition Release 11.2.0.1.0 - 64 bit)

  OS:                      Linux Fedora Core 17 (X86_64)

  I was reading the online documentation on schema triggers where oracle says:

  Assume that users user1 and user2 own schema triggers and user1 invokes a DR unit owned by user2. Inside the DR unit, User2 is the current user. Therefore, If the DR unit triggers the triggering event of a trigger schema that User2 owns, while the trigger is activated.

  I wanted to see this behavior in practice, so I made the following test case:

  -There are two schemas:
  
  

  • testuser where I create a procedure with AUTHID DEFINE (a unit of the Dr. therfore) named createTab. This procedure takes a table name as a parameter and if no table with this name exists already in the testuser schema, it will create a new table with the same name with a single column of type NUMBER (well, it's just an example to this issue, in practice I never create my tables this way)
    
    
  • training is therefore another scheme to which we grant the privilege EXECUTE on the above mentioned procedure createTab so that it may be possible to create tables on schema testuser by calling the remote procedure.

  The idea behind the test is to create a schema for testusertrigger, so that whenever he is, for example, a creation of the table, a message is inserted into a table of newspaper (just an example to show proof that trigger the diagram has been drawn on the table creation event). Now assuming I admit the EXECUTE privilege on the procedure of createTab for the trainingscheme, then any creation of the remote table must trigger the schema trigger, because according to the documentation inside the unit of the DR, the user is not considered appellant user (= training) but actually the owner (= testuser) that created the trigger and procedure.

  The problem is that I cannot see it in my test. Therefore I will write here my test case so that you can have a look at it and to indicate where I did wrong, and what I misunderstood in the documentation.

  So here's what I created on the schema testuser

  Code
  SET SQLBLANKLINES ALTER SESSION SET PLSQL_WARNINGS = ' ENABLE: ALL '; SET SERVEROUTPUT ON; -A table of newspaper in which the schema trigger inserts messages

  
  -indicating that the schema trigger was triggered (as proof)
  

  CREATE TABLE tablog (logMsg VARCHAR2 (100));

  -Here is the procedure that updates the above defined log table (tablog)

  -This procedure (autonomous transaction) is called by the schema trigger
  

  CREATE OR REPLACE PROCEDURE updateLog (p_logMsg IN tablog.logMsg%TYPE)

  DEFINE AUTHID

  IS

  PRAGMA AUTONOMOUS_TRANSACTION;

  BEGIN

  INSERT INTO tablog (logMsg) VALUES (p_logMsg);

  COMMIT;

  END updateLog;

  /

  DISPLAY ERRORS;

  -This is the procedure we use to create tables (which will be called so

  -remotely from another schema-> training)
  

  -As stated above, the procedure takes a table
  -name as a parameter and creates a table with a single column of type NUMBER

  -that if no table with this name exists already

  CREATE OR REPLACE PROCEDURE createTab

  (

  p_tabName IN user_tables.table_name%TYPE

  )

  AUTHID DEFINE - Therefore a unit DR that we explicitly specify AUTHID DEFINE
  

  IS

  BEGIN

  < < bk > >

  DECLARE

  tabName user_tables.table_name%TYPE;

  BEGIN

  -Check to see if a table with the name p_tabName
  -already exists
  

  T1.table_name SELECT INTO bk.tabName

  FROM user_tables t1

  WHERE t1.table_name = upper (p_tabName);

  EXCEPTION

  -No table with this name exists, so we create now
  

  WHEN NO_DATA_FOUND THEN

  IMMEDIATELY RUN 'CREATE TABLE ' |

  p_tabName | '(NUMÉRO n) ';

  END;

  END createTab;

  /

  DISPLAY ERRORS;

  - And finally it is the schema for the schema 'testuser '.
  

  -Any appeal of the above mentioned procedure createTab (if the procedure)
  -creates a new table) fires the following trigger
  

  CREATE OR REPLACE TRIGGER testuser_schema_tr

  Before you CREATE on testuser.schema

  BEGIN

  -Just insert a message into the table of the newspaper showing the evidence
  -that our schema trigger wiped of CREATE TABLE
  -statements

  updateLog

  (

  TO_CHAR (sysdate, ' ' MON-DD-YYYY HH24:Mi:ss) |

  ' ': Schema for testuser trigger pulled.

  );

  END testuser_schema_tr;

  /

  DISPLAY ERRORS;

  -I grant the privileges required for the formation of the user/schema
  -may also be able to remotely run my procedure

  GRANT EXECUTE ON createTab to training;

  GRANT SELECT ON tablog to training;

  First, I tested the procedure createTab locally (so be etre connecte connected as drawing testuser , in other words, the owner of the procedure and the relaxation). Everything worked pretty well and created table, that table the journal has been updated by the trigger which showed that in fact after each CREATE TABLE statement, the trigger was activated.

  However, when I opened a new SQL * Plus term, this time in being connected as a training scheme, I have observed that, once again, it was possible to create tables on schema testuser remotely, but the log table has been updated no more, which means that the trigger has not wiped CREATE TABLE statements that were issued remotely (by remote createTab procedure call).

  Code
  SQL > EXECUTE testuser.createTab ('tmptab');

  PL/SQL procedure successfully completed.

  SQL > SELECT * FROM testuser.tablog;

  no selected line

  SQL > USER to see THE

  The USER is 'TRAINING'

  
  

  SQL >

  Any idea? Why unity DR (createTab procedure) does not have the schema trigger, unlike what documents said, when it is called remotely?

  Thanks in advance,

  Dariyoosh

  It works for me on Oracle 11.2.0.3

  August 21, 2013 18:10:12: trigger pulled schema

  But not on 11.2.0.1

  It looks like a bug.

• compare the control unit when obtained from scriptures Sub

  Dear,
  
  I'm working on oracle apps R12, and I two business units when do two bills of different operating units and transfer to the GL, how do I compare journals it is for a specific operating unit in the database is there any ID in the database that I can compare different operating unit transactions that come from the sup to the GL book.
  
  
  Thanks in advance,

  Hello

  Ledger doesn't store information directly on the control unit which is normally captured at the transaction level.
  However, there is a table called GL_IMPORT_REFERENCES that keeps track of each worksheet that is passed from subsidiary ledgers to the General Ledger. This table has a column GL_SL_LINK_ID... This can be compared with a few tables over to reach the transaction source and pick up the reference of operating unit...

  (1) for the sheet, you want to know the GL_SL_LINK_ID of table GL_IMPORT_REFERENCES...
  (2) once GL_SL_LINK_ID is obtained, use the value in the XLA_AE_LINES table and collect the AE_HEADER_ID value...
  (3) once the AE_HEADER_ID value is obtained, use the value in the XLA_AE_HEADERS table and capture the value EVENT_ID...
  (4) once the event_ID value is obtained, you can check it with the ACCOUNTING_EVENT_ID of the base transaction... table column for accounts payable invoice it would be AP_INVOICE_DISTRIBUTIONS_ALL and for the payment of accounts payable AP_CHECKS_ALL... Similarly for other modules, the basic transaction tables would hold the reference... .Similarly each transaction table at the level of the subledger database allows to store the ORG_ID which is your value of operating unit...

  In addition, if your users provide a name for the JOURNAL by operating unit during the transfer of auxiliary accounting journal entries in the log book, you can identify by the same...

  Kind regards
  Ivruksha

• you attempt to add a web form of Business Catalyst to my site Web of Adobe Muse (via insert html) and the shape is cut all the content below where to place the html area.

  You attempt to add a web form of Business Catalyst to my site Web of Adobe Muse (via insert html) and the shape is cut all the content below where to place the html area. I tried the basic troubleshooting and it's only when I insert a form of Catalyst Business that my web page is cut, where is the bottom of the form. I use this code when you insert form BC in Muse,

  "< div class ="bulletin of information-form"> < form name ="catemaillistform58787"onsubmit ="return checkWholeForm58787 (this)"method ="post"action =" http://theincitejournal.BusinessCatalyst.com/CampaignProcess.aspx?ListId=53681& OPTIN = true & PageID = / index.html"> < div class ="form"> < div class ="item"> < label for ="CLFullName"> full name < / label > < br / > < input class ="cat_textbox_small"type ="text"name ="Full name"id ="CLFullName"maxlength ="255"/ > < / div > < div class ="item"> < label for ="CLEmailAddress"> E-mail address < / label > < br / > < input class ="cat_textbox_small"type ="text"name ="EmailAddress"id = '" "CLEmailAddress" MaxLength = "255" / > < / div > < div class = "item" > < label > Enter Word verification in box below < / label > < br / > {module_captchav2} < / div > < div class = "item" > < input class = "cat_button" type = "submit" value = "subscribe" id = "catlistbutton" / > < / div > < / div > < script type = "text/javascript" src = "http://theincitejournal.businesscatalyst.com/CatalystScripts/ValidationFunctions.js" > < / script > < script type = "text/javascript" > '

  The only settings I did took the H3 header on opt-in and page navigation after the action to get rid of the opt in BC function as default. I tried to download the source code as well and I'm having the same problem. The web Page is here " copy " and a version of what I was creating the page to look like here is ' home ' As you can see, the 'House' version allows me to scroll past where I would have placed the shape box while the 'copy' stops at any user to parade before. I have called the shape slightly from the "development" of British Colombia under the style sheets tab and still tried to trouble shoot and get rid of the code to see if it affects something and it did not add style. For some reason only the HTML to the form is but I cannot understand what the section of the code would do that. Any ideas?

  I see that you have inserted a script tag open that you forgot to close, which generates errors on the page and prevent it from be returned correctly. You should ensure that the code that you insert in the Muse is syntactically correct.

  

  - Abhishek Maurya

• planning of workflows - 11.1.2.2 reset of the planning units

  Hello
  
  a question about wf hyperion planning. How to reset the planning units? I still know that I must use the hollow administrator user, then:
  Log in as administrator
  Select file, process management, can manage the process.
  Select a scenario.
  Select a version.
  Select the superior entity > and select exclude cycle.
  
  but I can't perform this last action (exclude) because it displays on the secondary status column-> error: any defined by azione regola (error no rule not defined for the action).
  This way Iam not able to exclude plannign units. (some tests have been completed, change of owner of the PUs and actions: distribution...) Is it possible that a conflict has caused this error? )
  Right now, I see that auser (test) is the owner of all of the PUs. But also if I have access to one or another user, I'm not able to exclude CPU or change the status (no cell change status is indicated) how can I do?
  
  Thank you

  See also http://docs.oracle.com/cd/E17236_01/epm.1112/hp_admin_11122/ch09s05s05.html
  Error thrown when deleting the PUH is maybe not correct. If so you can try to remove the dependencies before PUH and try again

• What is the ORGANIZATIONAL unit support for?

  What is the OU = MyUnit stand for in the following permission file?
  < name > CN = Manager, OU = MyUnit < / name >
  

  <?xml version='1.0'?>
  <permissions>
    <grant>
      <principal>
        <class>javax.security.auth.x500.X500Principal</class>
        <name>CN=Manager,OU=MyUnit</name>
      </principal>
  
      <permission>
        <target>*</target>
        <action>all</action>
      </permission>
    </grant>
  
    <grant>
      <principal>
        <class>javax.security.auth.x500.X500Principal</class>
        <name>CN=Worker,OU=MyUnit</name>
      </principal>
  
      <permission>
        <target>cache=common*</target>
        <action>join</action>
      </permission>
      <permission>
        <target>service=invocation</target>
        <action>all</action>
      </permission>
    </grant>

  OR is the abbreviation for the organizational unit and is part of Windows Server Active Directory. When you add an organizational unit in Active Directory, this allows you to create a category for computers or users, or both. For example, in a high school, I can create an ORGANIZATIONAL unit for students have all my student accounts within that ORGANIZATIONAL unit and an OU for staff and have all my personal accounts in this OU. Now I can apply GPOS, or objects group, to this organizational unit policy, such as the Interface controls if I want to lock the student for example interfaces. You can also configure the computer OUS in them. So, for example, I can join a set of computers from the teacher to the UO staff within Active Directory computers after that these machines have been joined to the domain, and then apply a policy on that OU that says that personal accounts can ONLY log into these computers to prevent students to connect on a personal computer.

• Is compatible with Mac OS 10.12 (Sierra) with Logic Pro 10.2.4 and the iMac (21.5 inch mid 2011)

  Is compatible with Mac OS 10.12 (Sierra) with Logic Pro 10.2.4 and the iMac (21.5 inch mid 2011)?  I contemplate moving to Sierra, but not if it comes into conflict with Logic Pro.  Can someone advise?

  Thank you!

  Matt

  It was reported a number of not being able to save or to new projects with the title of the Sierra.

  I would conclude some time if I were you, especially if everything is working well at the moment.