The switching in APEX 4.0 themes

Similar Questions

• 2 ips in 1 switch how can I separate them in the network map

  When I map of the network and sharing Center it shows 2 computers enter 1 switch, 1 computer looks at his goes into each other before entering the switch, how to separate the 1 and got the 2 go in there alone?

  Hello

  I can't guess what the map is however the card is just programmable graphical presentation.

  In reality, if the computers are each connected to the independent switch ports and are not connected by a cable directly between them they won't in the other.

  If you provide more information on the network devices and how the cables are connected a better understanding can take place.

• Apex 5 universal theme: too much space between the bar and of the body of content

  Hello

  I work with the universal theme and my client is also enthusiastic about is that I am.

  I observed, this universal theme calculated the margin of the happy body at the end of the rendering and adds something like 100 px space between the menu bar and the content body.

  Many layouts which seems well - for some, it's a little strange.

  Is there a mechanism to place content in the title of body (which would allow almost exactly fill my requirement) or to stop this behavior?

  Or is this just a RTFM issue and I did not foud the manual jet?

  Concerning

  Sebastian

  Thx for your return. I tried to get a workspace APEX on the fly; but he has failed.

  So I had time to check.

  I used to write Javascript Code on Page 0 in the header after regions before putting them in files from APEX 4.0.

  As a result, Universale APEX 5 theme to a misinterpretation of the provision. "Container" (of the region

  ) was placed directly after the header section before the menu bar.

  Then the calculation of the provision made the rest...

  So I moved the "Javascript" - regions in the page footer Section.

  Now, the layout is fine.

  Cordially Sébastien

• Apex 42 5 theme image files in the list of the Navigation menus

  Environment: Apex 5 / 12 c/Linux

  Theme 42 - Menu Navigation

  I'm trying to configure the Navigation Menu to use images in the directory of the East (or #WORKSPACE_IMAGE #) rather than the css fontawsome images.  The help in the Navigation Menu panel shows that the option to use fontawsome css images or images of file system is controlled in the list template.  However, I can find no documentation on how the template must be configured to control this option.

  I copied the side Menu of Navigation list model with a new model (picture Menu in the side Navigation) and the Navigation Menu to use this new list (under User Interfaces).  I tried various constructions in the new model based on the construction of li JQuery for example replace the HTML for the list template in the sense of: -.

  "< li characteristics-current ="true"data-id =" "#A01 #" unable to read the data = "#A02 #" data-icon = "false" >

  "< a href =" "#LINK #" title = "#A04 #" > < img src = "#IMAGE #" / > #TEXT_ESC_SC # < /a > < /li >

  However this is made with a fake fontawesome class and the img tag is removed.

  Various other html constructs fail, which suggests that a flag is somewhere that is needed to indicate to the Apex renderer to use images of filesystem rather than fontawesome classes.  It doesn't seem to be a global setting or the option to configure this.

  Any ideas?  Or the development team would provide advice?

  Thank you.

  HI Paul,.

  Have understood you things by yourself very well.

  You are right that change the markup for the list to be used by widget tree side navigation will not affect the markup generated client side. It is similarly of the menu widget. The tree and the menu widgets are JavaScript data-driven. The markup simple list is just a way to let the models list APEX to create menus or trees. The markup simple list gets transformed into a JavaScript data which are then used to create widgets. The treeView widget and the widget menu cannot use the img tags to display icons.

  Say that 5 APEX uses FontAwesome icons or even the icons of fonts is a little too specific. APEX 5 uses CSS to specify icons. This includes using images and CSS sprite images as long as they are specified in the CSS. Based on the options you give, I think that you understand the situation. In addition to background images 64 Basic, you can use other background images as well. For example, an image of the CSS sprite comes with jQuery UI, and is at your disposal. Or you can use a single image. You can create your own images to sprite.

  Take a look at this simple demo application where I used some of the icons of the sprite CSS UI jQuery as well as some images from the APEX.

  https://Apex.Oracle.com/pls/Apex/f?p=81996:1

  I created a file called my_sprites.css and transferred as a static application file. Then I added it to the user interface of office under CSS files:

  #APP_IMAGES #my_sprites.css

  Here are its contents:

  body .a-TreeView .ui-icon.fa,
  body .a-TreeView .mi-icon.fa {
      display: inline-block;
      margin: 0 12px;
      vertical-align: middle;
      padding: 0;
      height: 16px;
      width: 16px;
  }
  
  body .a-TreeView .mi-icon.fa {
      height: 20px;
      width: 20px;
  }
  
  .t-TreeNav .a-TreeView-node--topLevel > .a-TreeView-content .ui-icon.fa,
  .t-TreeNav .a-TreeView-node--topLevel > .a-TreeView-content .mi-icon.fa {
      display: inline-block;
      margin: 0 12px;
      vertical-align: middle;
      padding: 0;
      height: 16px;
      width: 16px;
  }
  
  .t-TreeNav .a-TreeView-node--topLevel > .a-TreeView-content .mi-icon.fa {
      height: 20px;
      width: 20px;
  }
  
  .mi-icon {
      height: 20px;
      width: 20px;
      display: inline-block;
  }
  
  .mi-icon-calculator {
      background-image: url("/i/htmldb/icons/pt_computation.png");
  }
  
  .mi-icon-piechart {
      background-image: url("/i/htmldb/icons/pt_piechart.png");
  }
  

  The navigation tree side force the type icon "f" then the fa class is added to all icons. If the CSS overrides some properties for the fa class. Some other special css is necessary for when icons are in a tree. For the menu icons, I entered "mi-icone mi-icone-Calculator" for example Image/class field.

  I hope that this help show how to use other types of icons CSS.

  Kind regards

  -John

• How can I do a silent install of Firefox 23 because the switch - ms does not work?

  I was able to do a silent install of all the previous versions of Firefox by using the switch - ms. But when I use it on the new version, the user interface comes up and he has never done this before. I tried different silent switches but non of them work.

  Not the most experienced at this, but you use the stub Installer, perhaps you can try the classic installer and try again?

  Hope this helps.

  • https://www.Mozilla.org/en-us/Firefox/all/ < = full installer

• Two small buttons on the side of the switch just stop working - Tecra M5

  I had this problem before too many and I was told that the way to resolve the issue was a recovery CD, which means losing all my DATA and blabla... The problem is that the two very small buttons on the side of the switch just stop working.

  Just as that. They are always connected as when the laptop is on in standby or hibernation mode if you click on them it restart the machine. We tried something with Toshiba technician before and also their repair without success Center (change the purpose of the button, reinstall the program etc...) The only remedy was still a lot of recovery CD and a replacement of the machine, thank you for that. The sentence is still started. It could be a problem as cookies, just a wild guess or anything else.

  Now, nobody knows how to solve this problem, or had the same problem?
  Thank you. Olivier

  You talk about the presentation of Toshiba and Toshiba Assist buttons. Am I wrong?
  It seems that there might be corrupted registry keys or the common modules stopped working.
  Why? I put t know but perhaps I got a solution
  Try reinstalling the common modules.
  First remove it from the Add & Remove programs. Then restart the laptop and install the downloaded again common modules.

• How can I disable the Switch-to-Tab function? -I need to open multiple tabs in the same place...

  I need to keep several versions of the same site opened at the same time, and then switch between them... Apparently the Switch-to-Tab function will not allow this and keep my duplicated tabs become other Web pages...

  You can turn it off by using the switch to tab no Add on more - https://addons.mozilla.org/firefox/addon/switch-to-tab-no-more

• How do engage you the switch cover?

  I replaced the microphone cable in a pavilion of DV2617US.  Everything seems to be fine (?) but I can not replace the cover of the switch in place on the left side.  It seems that the left hinge is not completely.  The part of the joint that connects the laptop computer part to the display part is in the way of my snapping the cover from the rear switch in place.  I tried it SEVERAL times and diassembled several times as well.

  Help, please.  My friend wants her computer back.  Thank you!

  < steve="">

  Thank you.  I finally got it!

  I have the manual, thank you anyway.  Most other books I have include real photos, not rendered.   The problem there.  View of evil eye.  ;-)

  Pages 84 and 85 both show the two screws which were the culprits.  In the manual (believe me) that screws are horizontally side-by-side.  If you screw them in this way, the metal separates so either part little plastic of the motherborad.  But, a little enough to be a pain in my Assembly ass!  If you align them vertically, it works fine - just like the engineers built!

  Thank you very much for your help!

  < steve="">

• Having trouble getting the voice VLAN on the switch X1052P to work at all

  Can someone help me understand how to set up the voice VLAN X1052P? I spent several hours trying to get this working and it does not work. I spent about 4 hours on the phone with a Dell technician that night and he couldn't get it to work and finally gave up. He told me that I had to spend my warranty to ProSupport because he did not know how to solve the problem. What group of *. It's a simple configuration of VLAN. What must be so picky about? In any case...

  Setting up the VIRTUAL LAN must be fairly simple, but apparently on this switch is not. The user guide page 406 is not very useful except explaining what the different options. I must admit I am not an expert VLAN so I dunno I've misconfigured something. But remember, Dell technology could not operate either.

  Here's my situation... I have VoIP phones on my network connected to a network wall jack. Connected to phones are my computers of users. The computer of the user and its respective VoIP phone, both share the same data cable. Before replacing Cisco managed Internet service provider spend all it worked well. The problem is that they had direct access to our network so I removed the switch and installed the X1052P in its place. I talked to the ISP to let them know what I'm doing and they said everything I had to do was setup VLAN ID: 15 for the voice VLAN because this is the VLAN ID that the router uses to route telephone traffic. Router PSI is also the server DHCP VLAN 15 and issues IP for phones using 172.27.0.0/24 with a DHCP 172.27.0.50 range - 150.

  I tried to configure the switch using parameters of VLAN static and settings VLAN voice and neither one also seems to do what I want it to do.

  Network administration > VLAN > VLAN static

  Network administration > VLAN > Voice VLAN

  I activated the profile 'phone' on ports I want to added to the voice VLAN and it does not work. Moreover, 47 the switch port is connected directly to the ISP router and is configured as a trunk with the default port VLAN 1 unidentified and tag VLAN 15. For other ports I tried the general implementation, access and trunk of the parameters on each port to see if I could get something going and still nothing happens. When I set up the ports as General ports VLAN, I made adding VLAN VLAN 1 and VLAN 15 as a VLAN tagged not marked. It still does not.

  This is the short story from where I am now. Any help is greatly appreciated.

  FYI, as a follow up I finally solved the problem. I hope this information helps someone else that can encounter the same problem.

  After buying the ProSupport warranty upgrade ($121 out-of-Pocket mind you) and addressing a total of 4 technicians ProSupport expert technician a 3rd another level (only available via chat message between one of the ProSupport phone technicians and the 3rd Tier expert tech - i.e. I couldn't talk or chat with this person me) the consensus was that the material must be bad. When I bought the X1052P I bought two of them, so the best way to know if it was a bad switch was simply configure the other switch and see if the behavior occurs on this one, too. Well, this switch also restarted each time I assigned the profile 'phone' to more than 13 or 14 ports in the switch. It seems that it was not a hardware problem after all.

  I went back to the switch original and tried new things hoping that I could fall on a solution and it turns out that the solution was NOT to use the voice VLAN on the switch. It does not work!

  SOLUTION: I set the VLAN ID: 15 manually and no has not assigned any phone profiles to one of the ports. This is how I solved the problem.

  So he has bad software on the switch. I tried to see if there are updates of the firmware on the Dell support site, but there is none. Configure manually the phone VLAN was the solution. What a freaking nightmare which turned out to be. Maybe someone in Dell could note this problem and test in-house. And, if you want to compensate me for the 20 + hours I spent working on this problem, which has be great, too.

• Mode of the switch port to connect to a router

  I wonder what mode to set the switchport is connected to a router.

  I guess the cable between the router is connected to a port in trunk mode (for all the VLANS defined)? Then I Lass with gateways for VLANs pointing to the router routing interfaces?

  So in this way, if a neighboring switch does not know how to route a packet to an unknown IP address, the packet is sent on the trunk to the other switch. Here the appropriate VLAN SVI sends the packet to the appropriate router interface. Is this correct or nearly correct?

  Hi Atle,

  You can connect a trunk port or port access to a router. If you choose to use an access port, the router will form an adjacency only through the VIRTUAL LAN defined in this access port. If you choose a trunk port, you can use dot1q encapsulation on subinterfaces of adjacencies form on several VLANs. If you use a trunk you would this type of configuration:

  On the switch:

  item in gi1/0/1 interface

  switchport mode trunk

  switchport trunk encapsulation dot1q

  switchport trunk allowed vlan a to c

  On the router

  gi0/0.a interface

  encapsulation dot1q one

  IP address x.x.x.x y.y.y.y

  !

  interface gi0/0.b

  encapsulation dot1q b

  IP address v.v.v.v y.y.y.y

  !

  interface gi0/0.c

  encapsulation dot1q c

  IP address z.z.z.z y.y.y.y

  Here's a good tutorial on this subject:

  http://www.howtonetwork.NET/public/708.cfm

  Cisco service documentation:

  http://www.Cisco.com/en/us/docs/iOS/12_0t/12_0t1/feature/guide/8021Q.html

  To answer your question, you can use the router as a default gateway for hosts. In this case, should not have an IVR on the switch, except for MANAGEMENT purposes. Traffic from the hosts would take the path of the L2 to the router and then the router would make the next decision of transfer for the package. If you have two routers, you could do a safe for both routers and run a FHRP between them for redundancy.

  HTH

  Anthony

• The switch configuration of 6500 catalyst for IPS Inline the METHOD works

  I understand how to configure the switch Catalyst 6500 so that the monitoring of ports are access ports in two VLAN separate operation online.

  However, I don't see any document that describes how the desired VLAN traffic gets forced through the IPS.

  "Promiscuous" mode, you can use copy/capture VACL and forwards traffic wished the METHOD of analysis. I don't see how to get traffic desired through the IPS.

  Note that the 6500 host is running native SXE IOS 12.2 (18).

  Thanks for any help.

  A transparent firewall is a pretty good comparison.

  Say you have vlan 10 with 100 PCs and 1 router for the network.

  If you want to apply a transparent firewall on this vlan you can put not just the Firewall interface on vlan 10. Nothing would go through the firewall.

  Instead, you need to create a new vlan, say 1010. Now you place the Firewall interface on vlan 10 and the other on the vlan 1010. Nothing is still going through the firewall. So now move you that router from vlan 10 to vlan 1010. Everything you do is to change the vlan, IP address and the mask of the router remain the same.

  The firewall transparent bridge vlan 10 and vlan 1010. The SCP on the vlan 10 ae is able to communicate and through the router, but must go through the transparent firewall to do.

  The firewall is transparent because there no IP Route between 2 VLANS, instead, the same IP subnet is on the VLAN and the transparent firewall ensuring the beidges between the 2 VLANS.

  The transparent firewall can do firewall between the SCP on the vlan 10 and the router on vlan 1010. But PC has vlan 10 talks for PC B on vlan 10, then the transparent firewall does not see and cannot block this traffic.

  An InLine sensor is very similar to the transparent firewall and will fill between the 2 VLANS. And similarly an InLine sensor is able to monitor InLine between PCs traffic on vlan 10 and the router on vlan 1010, but will not be able to monitor the traffic between 2 PCs on vlan 10.

  Now the PC on the other vlan and the router on a virtual LAN is a classic deployment for the sensors online, but your VLAN need not be divided in this way. You can choose to place some servers in one vlan and desktop to another vlan. You subdivide them VLAN to whatever the logical method for your deployment.

  Now for the surveillance of several VLANs the same principle still applies. You can't control traffic between machines on the same vlan. So for each the VLAN that you want to analyze, you will need to create a new vlan and divide the machines between the 2 VLANS.

  In your case with Native IOS, you are limited to only 1 pair of VLAN for InLine followed, but your desired deployment would require 20 pairs of vlan.

  The IPS 5.1 software now has the ability to manage the 20 pairs, but the native IOS software doesn't have the ability to send the 40 VLAN (20 pairs) to the JOINT-2.

  Changes in native IOS are in testing right now, but I have not heard a release date for these changes.

  Now cat BONES has already made these changes. So here is a breakdown of basic of what you could do in the BONE of cat and you can use to prepare for a deployment native IOS when it came out.

  For VLAN 10-20 and 300-310, you want monitored, you will need to break each of those VLANs in VLAN 2.

  Let's say that keep us it simple and add 500 to each vlan in order to create the new VLAN for each pair.

  Therefore, the following pairs:

  10/510, 511/11, 12/512, etc...

  300/800, 801/301, 302/802, etc...

  You configure the port to probe trunk all 40 VLAN:

  set the trunk 5/7 10-20 300-310 510-520 800-810

  (And then clear all other vlans off this trunk to clean things up)

  In the configuration of JOINT-2 create the 20 pairs of vlan inline on interface GigabitEthernet0/7

  NW on each of VLAN original 20 leave the default router for each LAN virtual vlan original to the vlan 500 +.

  At this point, you should be good to go. The JOINT-2 will not track traffic that remains inside each of the 20 VLAN original, but would monitor the traffic is routed in and out of each of the 20 VLAN.

  Due to a bug of switch, you may need to have an extra PC moved to the same vlan as the router if the switch/MSFC is used as the router and that you deploy with a JOINT-2.

• Bypassing the switch mouse button

  Hi, for various reasons, I prefer to have the buttons left and right of the mouse when I use the computer, but there are some games, like Skyrim, FarCry 3 and TROUBLESHOOTING 2, who seem to ignore the switch and use the buttons by default.

  I guess that means that games recover the clicks of the mouse at the same time as the windows system, without waiting for them to be activated.

  Is it possible to fix this so that I can play as I want?

  Any help would be appreciated,

  Thank you.

  You will need to change within the parameters of the game itself, but very often they do not provide for such options.

• Is there a shortcut or an alternative ot turn it on wireless when you lost the wifi because the switch button seems no longer works? my laptop is hp 8560w

  The switch for the wireless button is always orange and nothing happens when I press them.

  Its possible, you could go into the BIOS of the laptop and make sure that the wireless hardware is enabled (available on some models only). Consult this manual for possible help with that...

  http://bizsupport1.Austin.HP.com/BC/docs/support/SupportManual/c03424153/c03424153.PDF

  Beyond that by looking at the user manual it doesn't seem to be a combination of function for this laptop switch switch wireless only top of page material.

  http://bizsupport1.Austin.HP.com/BC/docs/support/SupportManual/c02970545/c02970545.PDF

  If you suspect a problem of material and the laptop is still under warranty I would contact HP for assistance...

  There are also forums for HP to possible assistance...

  http://h30434.www3.HP.com/T5/notebook-hardware/BD-p/hardware

• APEX 5, universal theme, value pairs attribute - column layout problem

  Hello

  APEX 5, universal theme.

  I have a little problem with the column model attribute - value pairs.

  If one of the fields is the result of a LOV and the value of the field is zero the provision goes a little wrong (half a row of the value column), when having long lists of pairs, it is difficult to see what value belongs to what field. It is a horizontal allignment problem that looks like the below example, the field in the middle is an empty field based on a LOV.

  Think of it as a little bug. Maybe someone can provide an easy solution?

  See you soon,.

  Bottom

  It looks like a bug in the CSS of the theme. This rule

  .t-AVPList-label,
  .t-AVPList-value {
    display: block;
    vertical-align: top;
    font-size: 1.4rem;
    line-height: 2rem;
    padding: .8rem 1.2rem;
    margin: 0;
    box-shadow: 0 1px rgba(0,0,0,.05) inset;
    transition: background-color .1s;
  }
  

  needs a property added minimum height so that the heights of term/description elements are aligned if one (or both) of them are empty:

  .t-AVPList-label,
  .t-AVPList-value {
    display: block;
    vertical-align: top;
    font-size: 1.4rem;
    line-height: 2rem;
    padding: .8rem 1.2rem;
    margin: 0;
    box-shadow: 0 1px rgba(0,0,0,.05) inset;
    transition: background-color .1s;
    min-height: 4rem;
  }
  

  You can create a style sheet personalized containing a rule of precedence for this problem:

  .t-AVPList-label,
  .t-AVPList-value {
    min-height: 4rem;
  }
  

  Transfer it to your workspace and reference it in the theme CSS File URL property to include in the app:

  #THEME_IMAGES#css/Core#MIN#.css?v=#APEX_VERSION#
  #WORKSPACE_IMAGES#theme_42_AVPlist_fix.css
  

• How to edit #TEMPLATE_CSS # a topic at the 4.2 APEX?

  Dear Experts,
  
  How to edit #TEMPLATE_CSS # a topic at the 4.2 APEX?
  
  Best regards
  Mahmoud

  Mahmoud_Rabie wrote:
  Dear Paul,

  To be more precise, I have the following

  in my page template.

  I know, #TEMPLATE_CSS # is replaced with the contents of the file above.

  No, it isn't.

  As described above, #TEMPLATE_CSS # is replaced with the contents of the File URL and Inline CSS of the model properties. This feature allows the customization level of the CSS model included in the page. Try it: change #TEMPLATE_CSS # in the model:

  
  #TEMPLATE_CSS#
  
  

  Now add a style to the Inline CSS property:

  body { background: black !important; }
  

  Run the page. View the source of the page in the browser and see what happened to #TEMPLATE_CSS #...

  The question is: I (by APEX 4.2) can I update this content directly to do tasks such as adding or upgrading the CSS classes?

  Not in the way you want to say.

  URL of the file and Inline are empty (default) and ready to be used to completely replace the content of #TEMPLATE_CSS #.

  Yes, #TEMPLATE_CSS # is replaced with the contents of the properties of model File URL and Inline . Affecting not the inclusion of other information of CSS, you use the new channels of alternative CSS < link rel = "stylesheet"... > elements, or embedded statements < style > .

  Is the only solution to update/change the CSS for a theme to download CSS then paste it in the field on line (under the section the model CSS)?

  N ° if you want a custom theme, the best way is:

  1 copy the CSS theme at a place accessible in the file system (at best) or a trustee of the APEX (if you don't have access to system files).
  2. create a new theme as a copy at the APEX.
  3 change the < link rel = "stylesheet"... > references topic in the new theme templates page to point to the new location of CSS.
  4 customize the CSS (like Coda which allow locals and edit files remotely is quite useful).