The user read/write register access to the network folder/drive. Some users unable to save or write to the directories.

Similar Questions

• Home network: folder/drive share with specific users

  I have 4 computers on my home network.
  COM1 is the main desktop computer & 3 laptops (LAP1, LAP2 & LAP3 for example)
  COM1, I have 2 physical disks (Drive E & Drive-F) shared to everyone, so all 3 laptops
  full access to them.
  Now, I want to exclude Drive-F LAP3. How do I do that?

  First of all, I thought that I could change the permission on the part of the reader-E & Drive - F by manually adding all user names identified in the homegroup (instead of setting the authorization of "Everybody"), like this:
  -In car-E sharing: user name of COM1 + LAP1, LAP2 LAP3
  -In car-F sharing: user name of COM1 + LAP1, LAP2

  Apparently, it is not as simple as that.  Windows can watch only the local computer users. It can display the names of users in network (LAP1, LAP2 & LAP3).
  If this is the case, how could I achieve this?

  Some read it here (Brent-Support Engineer response):
  http://answers.Microsoft.com/en-us/Windows/Forum/windows_vista-security/cannot-add-network-user-names-to-file-sharing/0bff8b46-3212-497e-A051-0797e9a2f88d

  It seems that I can accomplish this by creating (with the same user name) for each laptop in COM1 and add user names manually for sharing (for each shared drive) permissions, like my scenario above.  Am I wrong?

  Hello

  Thanks for posting your question in the Microsoft community!

  You can add computer laptop name\username and granting permissions.

  If the problem persists, or you need help on Windows let us know.

  We will be happy to help you.

• OfficeJet Pro 8500: Officejet Pro 8500 A910 - unable to access configuration for the network folder screen.

  I can't access my webpage "network folder Setup.

  I can access my page main printer very well using the IP of the printer.   I click on Scan up fine, I then click on "configuration of the network folder" and it tries to load and then goes to a screen "ERR_CONNECTION_TIMED_OUT".

  He warned me the first time that he has been using HTTPS and I approved that.  I currently records on my printer set up awhile back and they work fine but must modify and add a little more.

  I tried multiple computers and devices with the same results.

  Thank you

  Chris Gaines

  MALVERN, AR

  Hello @Cgaines78,

  Thanks for dropping by the HP's Support Forums! I see that you run into issues trying to set up a folder network for your HP Officejet 8500 A910.

  Please continue troubleshooting here: scan to a computer, the e-mail, the device memory or the network folder

  This aid? You are now able to set up a network folder?

  Let me know the results. If this resolves the problem please let others know to mark this message as "accept as Solution".  Just say thank you, please click the ' Thumbs Up ' button. If you need more assistance let me know and I will gladly do whatever I can to help.

• How to give read, write permission to the directory from one user to another user in oracle 10g

  Hello

  I have a database in two. key is the source database and Board of Directors is the target database. Now I want a (single) create these two database directory to put the dump file. How can he give permission to READ, WRITE access to this directory both of database? Someone help me.

  Hello

  I think that first create a level of operating system directory, and then try Mr.Kar k steps

  OF DATABASE1 (KEY)

  SQL >dir1 CREATE or REPLACE a DIRECTORY as "/ opt/oracle / ';

  SQL >GRANT READ, WRITE on dir1 to the PUBLIC; (if you want to give access to all users then give public access)

  SQL >GRANT READ, WRITE on rep1 to ; (if you want to give access to the particular user)

  OF BASE2 (COUNCIL)

  SQL >CREATE Or REPLACE rep1 as DIRECTORY "/ opt/oracle / ';

  SQL >GRANT READ, WRITE on dir1 to the PUBLIC; (if you want to give access to all users then give public access)

  SQL >GRANT READ, WRITE on rep1 to ; (if you want to give access to the particular user)

• Create the table and take the name of user who can read/write on this table

  Dear gurus,
  
  I need to add the following column in Oracle 11g DB AND also add the name of user who can read/write ONLY the following table, any table to access the same read?
  
  I use to go to Oracle PL/SQL client.
  
  My dbname is 'customerdb '.
  
  TableName: "extractOrders."
  
  +: example of the field data.
  Column0 = logID: 1
  Column1 = idNumber: 39D13613-F061-D38D-100A-16536409C6D8
  Column2 = timestamp: 2011/07/11-13:45
  Column3 = resultCode: 40509
  Column4 = resultMessage: could not find the IDENTITY card
  Column 5 = number: 9813080808
  Column6 = iid: 87670200100001466100
  Column7 = products: D1430 | "' S1412 ' | "" S1407 | "' S2607 ' | "' S1417 ' | "" S1411 | "' S1413 ' | "" S1502 | "" S1406 | "' S1522 ' | "' S1524 ' | "' S1474 ' | "" S1473 ".

  user596669 wrote:

  I need to add the following column in Oracle 11g DB AND also add the name of user who can read/write ONLY the following table, any table to access the same read?

  I use to go to Oracle PL/SQL client.

  Let's say your table than extractorders is the schema of database clientsproperty.

  As this pattern create a stored procedure that runs with the privileges of the customerschema. Having this procedure return a ref cursor For example

  create or replace procedure ReadExtractOrders( c in out sys_refcursor ) authid definer is
  begin
    open c for select * from extractorders;
  end;
  

  As this code executes with the privileges of the customer schema it can read the table belonged to this scheme.

  Now give execute rights on this process for the Joe database schema - and this pattern can create a cursor on the table of ExtractOrders , without being able to access or use directly or refer to this table. Read access to this table is therefore protected by a reliable code belonged schema customers.

  Learn about the AUTHID clause and how it can be used to differentiate the code approved and non-approved, which allows to PL/SQL code to run with different privileges than the demand for prescriptions.

• Cannot access the card reader/writer internal Flash

  After a few updates, I can access is no longer any SD card inserted into the card reader/writer Flash. I tried to use the convenience store but just that said there is no problem found. When I insert the SD card, it appears in the 'control Panel\Hardware and Sound\Devices and printers' as ' Flash Card Reader/Writer "but I am not able to access the card.

  Hi Tim,.

  Was there a card player offered to you via Windows update driver update?

  -You see no drive letter assigned to the flash card while you see for readers in the window 'computer '?

  -What is the error you get when you go to the map?

  I suggest you try to change the drive letter assigned to the card and see if that helps.

  1 type diskmgmt.msc in the RUN prompt or in start search to open the computer management window.

  2. right click on the indicated card device and select "paths of access and change drive letter.

  3. click on change if there is an assigned drive letter, and then change to another letter. If this is not the case, click on add and select a drive letter.

  4 restart the computer so that the changes are applied and see if you are able to access the content in the map.

  For more information: http://windows.microsoft.com/en-in/windows7/change-add-or-remove-a-drive-letter

  Alternatively, you can try to uninstall and reinstall the drivers for the card and see if that makes a difference.

  Visit the website of your computer manufacturer to download and install the latest drivers.

  Let us know the results.

• Am about to buy DW.  2 quick questions before proceeding.  (1) can I associate a DW created an EXTERNAL SQL Express database for the read/write site?  Can be made safe?  (2) am plans to use Contribute to allow non-technical users to end dry change

  Am about to buy DW.  2 quick questions before proceeding.  (1) can I associate a DW created an EXTERNAL SQL Express database for the read/write site?  Can be made safe?  (2) am plans to use Contribute to allow non-technical end users EASILY change the sections of the web site.  Can this work?  Thank you.

  I would like some ideas.

  A CMS is the standard solution in the industry today. The most common environment is LAMP (LINUX, Apache, MySQL, PHP).

  Some of us to write custom CMS systems for a living. I concentrate on CMS for retirement centers. There are all kinds of solutions CMS available ranging from generalist, off-the-shelf CMS like WordPress, completely custom, with a lot of opportunities in the meantime.

• Object LVOOP read/write using the API TestStand

  Is it possible to read/write a LVOOP object to a variable TestStand from LabVIEW using the API of TestStand?

  SetPropertyObject() takes a green wire reference, which is incompatible with an LVOOP object.  SetValVariant(), SetValIDispatch(), and SetValInterface() seems to just write a value null of type variant.  I don't know if I use the wrong API function or if it's just not possible.

  Hi jsiegel,

  That's right, it is not quite possible to what I believe, it is your intention. As mentioned, TestStand cannot create the object of LabVIEW. To make and use references of LabVIEW with TestStand, you need LabVIEW out this reference, which may then store it TestStand as an object reference. For VI requiring the obeject LabVIEW as an input, the registered object reference can be passed in. To make calls to LabVIEW classes using the class member call with a step of the VI Action instead of the call to VI for the Type.

  Of course, you need both LabVIEW and TestStand 2012 or newer in order to use these functions.

  Kind regards

• Synchronization with Serial read/write problems. can not get the functionality of the terminal emulator

  Hello

  I am writing a VI to control PWM with a microcontroller via a serial port. I wrote a simple code for the microcontroller that allows me to set the ratio of duty cycle on a scale of 0-65535. It works very well with Termite of Compuphase (RS-232 plug); The microcontroller invited me to an entry, expected that I would one, updates and expected another entry when I decided to send him. Now, I'm trying to get the same functionality on a LabVIEW vi but hit a snag.

  When I tried to send my orders with a series read base and an example of writing, everything worked fine. I could see the prompt entry, write an entry and if I was quick enough, check out the update message. Even when I was not fast enough, I was able to check the update by monitoring the PWM pin with a Logic Analyzer. The problem with the basic example, however, is that I need to update the report to aura cyclical ratio, so I went for an example of reading continues writing. The problem I've met; is that I have to switch between reading and writing to make it work. When I do that, either I don't hold write it down long enough and nothing happens, or I get several updates when I switch to reading. Some of these updates don't even match and produce updates to defective upgrades for example; 16000 16000, 16000, 16000, 6000, 600, 60, 16000, 1600, 60, 0, 0, 0, 16000, 60, 0, 0 etc.

  I tried which allows characters of endpoint in the hope that the writing would end at the end and go to reading where he would receive a termination character and wait for me allow writing once again, but nothing helped. I still have to alternate between the two and either get no response on reading several updates of variable accuracy. I tried to remove her allows read/write and their structures of matter in the hope that the loop flow, associated with the characters of endpoint would the case, but then the updates don't register at all. The funny thing is I did a VI like this before with an Arduino and that there not even no need to switch between writing and reading (I'm now using a Board of Freescale FRDM).

  I was also the frequency of timeout errors; Error-1073807339 at VISA Read, reason Possible: VISA Hex 0xBFFF0015. I removed the option to stop the while loop if there is an error so I can run but always pops up an error on the judgment occasionally. Could the problem of synchronization always cause me problems?

  Would appreciate all advice really, I am providing my slightly modified example screws and can provide the code for microcontroller on request, even if it's very simple.

  Thanks in advance, it is
  Yusif Nurizade

  In other words, frankly, a good bad example you according to your code. Also, you have the order of writing and read upside down in your amendment if the instrument requires a command to return something. It should really be using a structure of the event. The structure of the event around a write and read and use a value change event. I have attached a quick change. This mod is still a reading after writing. If necessary, you may have two separate events to write and read.

• Make the NTFS read/write permissions without possibility to create/delete folders

  Out to one of our sites, we have a server running Windows Server R2 of 2012 which took a file share accessible to our people on the spot. Our project managers have developed a very strict folder for this file share structure, and for the purposes of verification, they want to stick to the closer this structure as possible.

  Therefore, although the local people must have read/write access to create, edit, and delete files, they won't they are able to create or delete folders. They want to use the existing folders and not to store stuff in folders that nobody knows there is except for the person who created them.

  The closest way to you, I got to do is to uncheck the advanced permissions "create folders / adding data" and "Delete subfolders and files." This has some side effects, however, the most notable being the inability to add data to the files, some files (such as CAD drawings) can be changed by anyone except the person who created them.

  Is there a way using only the NTFS permissions to accomplish what the project leaders? And if not, are there any third-party utilities that will help us do this?

  Thanks in advance for any help.

  Try asking in the Windows Server forum:
  http://social.technet.Microsoft.com/forums/en-us/category/WindowsServer

• Difficulty using the binary read/write

  Hello

  The binary read/write function somehow not working properly in my application.

  I have one store a 2D strign binary array. When the user closes the application, the application stores the values in table in the Bin file.

  N when the application starts, it reads the file and displays its contents on the table.

  The system works well if the total size of the content is 3 bytes. But if the size of the content is greater than 3 bytes, the program simply returns a NULL value at first when I read the Bin file.

  How to save:

  Convert 2D in String table using "Flatten the string" fn and to save in a binary file.

  Procedure to read:

  read a binary file. convert the output string table 2D using 'string Unflatten ".

  I enclose my code here. PLS, have a look at it and let me know the cause of the problem.

  Ritesh

  I don't understand why you're flattening of a string, a 2D channels table. It's redundant. You seem to be also the substitution of the default big-endian to little endian byte order. You try to save it in a format suitable for other programs on other platforms?

  If this is not the case, all you have to do is:

  

• Diffrence between the tablespace is ONLINE and READ WRITE?

  Hi all

  I'm very confused on the tablespace is ONLINE and READ WRITE?

  Some say that if the tablespace is online, this means that its READ WRITE and when its offline then its READ-only.

  So, what is the difference between them:

  ALTER TABLESPACE offline tablespacename; -> done mean READ only now?

  ALTER TABLESPACE tablespacename online; -> is it means its READ WRITE now?

  If Yes, then what is the use of the following command if above 2 commands? :

  ALTER TABLESPACE tablespacename [READ ONLY |] READING WRITING];

  Kind regards

  Confused Ritu

  In addition, when the tablespace is offline, objects belonging to those who are not available for use to users. You wouldn't be able to query for objects in a tablespace offline.

  When the tablespace is read only - no write operation cannot be performed i.e. etc. INSERT/UPDATE/DEL. Oracle says that read-only tablespaces provides a way to protect the historical data so that users cannot modify it. You can drop objects, such as tables or indexes, to a tablespace read-only, but you can't create or modify objects in a tablespace read only

  In order to bring a tablespace OFFLINE to ONLINE - so that it is available to users, you must "ALTER TABLESPACE online tablespacename" command. A tablespace online can be READ ONLY or READ WRITE mode.

• How to check the instance datafile I/O? solve the high physical reads/writes?

  Method-1
  identify 'hot spots' or I/O contention
  Select NAME,
  "Physical reads," PHYRDS
  round ((PHYRDS/PD.)) (PHYS_READS) * 100, 2) «Read %»,
  PHYWRTS "physical Scriptures."
  Round (PHYWRTS * 100/PD.) PHYS_WRTS, 2) "% of writing."
  FS. PHYBLKRD + FS. PHYBLKWRT "Total block I / O of.
  de)
  Select sum (PHYRDS) PHYS_READS,
  Sum (PHYWRTS) PHYS_WRTS
  v $ filestat
  ) pd,.
  v$ datafile df,.
  v$ filestat fs
  where df. FILE # = fs. FILE NO.
  ranking by fs. PHYBLKRD + fs. PHYBLKWRT / / desc
  
  
  Another method-
  On Oracle10g, CWA also provides the dba_hist_filestatxs table to track the disk i/o:
  
  break on begin_interval_time jump 2
  
  column phyrds 999 999 999 format
  column begin_interval_time format a25
  
  Select
  begin_interval_time,
  file name,
  phyrds
  Of
  dba_hist_filestatxs
  natural join
  dba_hist_snapshot;
  
  It is - method that you use to check for errors in data I/O file? AND how to solve high physical reads and writes?

  Ankit Ashok Aggarwal wrote:
  AWR project stat e/s in terms of segments, query and etc.
  Here, my concern is what should be the value of ideal threashold for a DBA to act on the high physical reads/writes?
  and how he can fix this problem if it affects database performance?

  I don't think that there is any possibility to mention that the amount of an e/s is going to be good or bad for a database in general. The reason is that it is not quantifiable. For example, in a store, maybe one day that no one gets and another day, there is no place to stand (because there was a sale announced by the store). So now, how do you say that it was not necessary? Rather than search for best practice values, it is best that you keep track of the normal functioning of your db and when you see a special summit in the values of events scattered user IO as DB file read, DB file parallel read etc and when this happens, you should check back the work you are doing and see if that can be refined somehow.

  Aman...

• Help? the source volume is read-write and can not be disassembled...

  I use 10.11.5 on an iMac 21.5 ", end of 2009 and I want to restore the OS X 10.11.5 to HD on an external drive but I get this message" Source volume is read = write and cannot be disassembled, so it cannot be copied from block. "  I can find answers do not address El Capitan.  Help would be greatly appreciated.

  .. .Goldie

  You use disk utility's restore feature?

  If the HD has a recovery partition, you can make starting in place of the recovery.

  Or you can use SuperDuper! (the basic version is free and can copy the entire disk, the paid version allows "smart updates", which copies only files that are different, saving time) running on externally to perform the copy.

• How to read/write tdms 2.0 files with the TDM C DLL?

  Hello

  How to read/write tdms 2.0 files with the TDM C DLL?

  How consequently the datas in interlaced with the TDM C DLL mode?

  Thank you

  Confirmation: TDM C DLL always wrote the file in TDMS version 2.0.