Time Capsule: create networks of 5.0 and 2.4 with different names

Similar Questions

• process step by step new airport express from apple with time capsule base of connection (cable cat 5 150 Ft) with late 2008 macbook

  I would like a step by step process apple a new airport express with time capsule base of connection (cable cat 5 150 Ft) with late 2008 macbook.

  Connect one end of the long Ethernet cable (we assume that you have already tested the cable to make sure it works correctly) one of the three ports LAN <>- on the Time Capsule to the WAN port on the AirPort Express "O".

  

  We assume that the AirPort Express is new, is powered OFF... and has not been previously configured.

  Turning off the Time Capsule

  Wait a few seconds

  Put in the Time Capsule market and let it run a full minute

  Power of the AirPort Express and run a full minute. Currently, the indicator light of the Express slowly flashing orange

  On the MacBook, click the WiFi status menu icon and search for a list of the new AirPort access point

  Just below this list, click on AirPort Express

  

  Who will get the "Assistant" operational configuration. It will take a few seconds for the wizard to analyze the network and offer the correct setting in a display that will look like the example below, except that you can see your cameras and the name of your wireless network.

  

  In short simple name you want to call the AirPort Expressof type... .as OfficeExpress, for example

  Click Next

  Watch the next screen carefully to confirm that the AirPort Express is in place to extend using Ethernet, which confirms that the installation wizard recovers the wired between the Time Capsule and AirPort ExpressEthernet cable connection, so the settings correct configuration will apply.

  

  When you see the message Setup is complete, click done. Close the installation window, and you're done.

• Problem of Time Capsule Roaming Network airport

  I'm having a problem by establishing a network of roaming.  When I plug my extender devices in ethernet cables through a switch to my Time Capsule base station, my wifi signal drops 150 + MBS next to the base station to < 10 mbs.

  I have a wifi in my home network based on a new time Capsule airport base station (ATCBS) running firmware c. 7.7.7.  I have my 4th gen AEBS & a 2nd gen Airport express both race v. 7.6.7 updated firmware in place in Bridge mode to extend my network in different rooms in my house. The system works very well, but I wanted to increase the power of the signal in remote places so decided I would like to convert it to a mobile network by installing ethernet cables to connect my ATCBS the AEBS and express extensions.  I use a switch Netgear 5 port (NOT of GS205-100) that I only have a single LAN fanless available left port on my ATCBS.

  I installed 3 ethernet lines-1 each in rooms with my ATCBS and airport express using mounting wall punch down taken using the convention of wiring 568B, AEBS.  These lines all end with male plugs in a unique space in the basement and are also wired as 568B.  Then I plug the ATCBS, AEBS and express lines in the switch in this remote area.

  I've done a few connection cables in the role of Cat 6 cable, I had over the House, and they all very well with my cable Tester check so I know the cable itself is not defective.  The cables all run in the basement where I can see, so I know there is not any problem to be crimped/damaged.  I have not any gear to test the installed well son.  I visually inspected the male and female (punchdown) ends to ensure that colors are properly prepared.  I did a test of my jacks punchdown conductivity by testing 8 wires on the sides of the socket and the pins in gold on the inside where an ethernet cable connecting between the cut ends.  All wires are correctly leads to the appropriate pins.

  If I plug just the ATCBS into the switch next to him and using a good patch cable I see no change in the strength of the Wifi.  If I can plug my express (also moved to the room of the base station) using another cable good patch in the switch, wifi drops as described above.  If I plug the ATCBS on the new socket and the switch at the other end - no change in force wifi.  If I plug the express in its remote location system also uses the new ethernet cable installed for him and passing through the switch, I get the wifi signal reduction.  I get the same result if I take the express up to thevbasemenbt and plulg the switch with a connecting cable).  It seems therefore that the problem may not be with the newly installed cables that I get the same result by using or by using cables good patch, and with the switch in the same room with the ACTBS.  It doesn't matter how I'm trying to connect all the devices together, plug extender devices into the system brings the WiFi falling to almost nothing.

  Any ideas on what could happen?

  I'm having a problem by establishing a network of roaming.  When I plug my extender devices in ethernet cables through a switch to my Time Capsule base station, my wifi signal drops 150 + MBS next to the base station to < 10 mbs.

  That's what happens when you initially set up the device to the airport "extend" using a wireless signal... and then later connect an Ethernet cable to the unit of the airport.

  Since the airport is configured to connect wireless and waiting for a wireless connection, the Ethernet connection and then creates a feedback loop massive on the entire network... in fact, basically crashed the network.

  Basically, you have to start over again with the AEBS and AirPort Express and "Apple Installation Wizard" to set things upward. It's practically automatic. All you need to do is assign a device name to each airport and the wizard supports all the rest.

  After the back if you need some advice on how to correctly configure things.  You can be amazed at how simple, it comes... and surprised by the wizard settings apply.

• Time Capsule has lost the Internet connection and DNS servers

  I use a Time Capsule for Time Machine via Ethernet backups for a couple of years, use it in mode bridge taking its Internet connection directly from my router and connected in turn by Ethernet to my iMac. (Most of the time that I also had wifi off on my iMac and took my Internet directly via the TC Ethernet connection.) A few months ago I upgraded to El Capitan, and the TC has lost its connection Internet (flashing yellow). A few days later I drove back to the Yosemite (for other reasons - Mail had gone mad) to restore a backup of the TC and everything was fine again for a few months. It may or may not be meaningful I plugged TC yesterday to new laptop for my wife to support for the first time, and this laptop is running El Capitan. Since then, the TC has once more lost its Internet connection and DNS settings and is stuck on flashing orange. By clicking on the 'Internet connection' status alert, tells me that the TC is not a valid IP address.

  

  I have reset the TC, repeatedly and reconfigured but all without success. After consulting the other discussions, I also tried giving the unit an alphanumeric name with no spaces & special characters and change the IPv6 "Link-local" configuration only, but this did not affect the result. And I updated the firmware for good measure. Then I unplugged overnight and carried out a full power cycle the steps recommended here, restart the router, TC and the computer (and performed a factory reset on the TC, while the router & computer was turned off). After doing that, the TC has become undetectable by AirPort Utility, until I have reset reconfigured once again, he and ended up in the same place.

  It may or may not be important to mention the following:

  1 when you set the TC after a reset, I repeatedly selected the option of adding to an existing network instead of create a network, but the installation wizard who ignored each time.

  2. in the installation each time, this point, I shows me the following, which seems to suggest that there is a problem but don't say so explicitly:

  

  I would be grateful for any advice.

  Weird how everything's going well for a few years and then crazy when you have something will change.

  El Capo adds some network problems more... but something could be fundamentally wrong with the installer.

  Your current configuration, it is apparently bridged but cannot get an IP address. The address 169.254 is give it since it's self generated.

  You need to do a manual installation. It simply means the Assistant is unable for any reason to be your network so start over and do it manually of misfortune (wow, or also possible misery, woah being where you are now!) to go...!

  1. I need to know what modem you are connected. Make and model please?

  2. the most important. What is the main router on your network or a modem?

  I gave the edge to make manual settings a few times. Somehow my instructions for Yosemite/El Capo got lost... I'll try and hunt down them. In the meantime, the basic method remains the same.

  https://discussions.Apple.com/thread/6509420

  It is not so difficult... You just know where you're going before you start.

  Airtport Utility cannot find airport Time Capsule on one of my Macs 2009

• Time capsule airport unplug my Airport Express and internet

  Howdy,

  I just brought my Airport Time Capsule of the work. I have the joint via an Ethernet cable to my extreme, both are in my basement. Upstairs, I have a set Express in place to expand the wireless. The extreme and Express worked for many years now.

  Once the time Capsule has been recognized in the public services of the airport, he made an update of the firmware.

  After that, I edited the settings for the time Capsule to my home network and set it to "develop wireless."

  Extreme, Express and Time Capsule all had them green to light up in public services - so I tried to run a Time Machine backup, and things went sour.

  The cable modem the extreme is connected to started to abandon the connection every 30-45 seconds and the Express light went red and there is no longer recognized, so I clicked "forget" to remove it. Time Machine could not locate the time Capsule.

  So I unplugged the Time Capsule, all rebooted and now my extreme and Express up and running again.

  What waste?

  Thank you

  Dan

  After that, I edited the settings for the time Capsule to my home network and set it to "develop wireless."

  I think you probably mean "extend a wireless network".

  This is the bad setting... because it would be used only if the time Capsule connected to your network using Wireless.  You specify the Time Capsule connects using Ethernet.

  Here is what is happening now... the time Capsule waiting for a wireless connection, but he gets an Ethernet connection.  This translates into a huge feedback loop that effectively blocks your network.

  The correct setting for the time Capsule would be "create a wireless network"using the same exact wireless network name, security and password as other Apple routers. " Finally, make sure that the time Capsule is set to run in Bridge Mode before you click Update to save the new settings.

• HOW THE AIRPORT TIME CAPSULE WIRELESS NETWORK IS PROTECTED?

  I implemented the airport Time Capsule, using a DSL modem connected to the internet as its bridge.  MacBook Pro was used for initial set up by the bolt of lightning to Ethernet connector and then disconnected and works perfectly.  Now, I would like to use Wi - Fi for my Samsung phone not iOS.  On the Samsung wireless I connect to my home network using a password.  Well, I don't think that a password was never set.  How can I configure my wifi at home to establish a password?   I don't think that the modem settings should enter in solving this for me, but I'll add that the modem required a static IP address be entered for this connection when its router features have been disabled for the connection of bridge.

  If the Time Capsule (TC) provides the wireless network, then you can secure it using AirPort Utility, as follows:

  • Run the AirPort Utility.
  • Select the TC and then, select change.
  • Select the wireless tab.
  • In the wireless security, select the type of security. I highly recommend that you choose: WPA2 Personal
  • Enter a password in the field password wireless. Enter the same password in the verify password.
  • Select Update.

  

• Time capsule 'unexpected error' despite the reset and the IPv6 local link configuration

  Hello

  I try to use a time capsule that I have not used for a long time to backup my mac.

  I have adware on chrome and safari that I cannot get rid of (trovi) despite several attempts (extensions, resets etc.)

  I decided to upgrade to el capitan, so that I could use software removal that does not work on Lion, but now I can't save because time capsule gives me "error unexpecetd".

  I have reset the TC and I configured link-local IPv6, but am still having the same problem.

  Anyone know if it is a question can be resolved?

  Thank you!

  It is possible that software that you download to help get rid of the adware etc... blocking the work TM... affects a lot of bad a antivirus software on Mac OS. McAfee is one of the worst.

  What operating system are you currently using?

  There is no need to upgrade... but it is necessary to clean install.

  Download and use Carbon Copy Cloner. You can use it for free for a month... I highly recommend you do the backup on a USB key connected to the Mac, so it can be made bootable... and then can be tested immediately.

  You can use the TC and the backup to that... but you can't boot from network drives.

  I can recommend you to do a clean install... just wipe the mac and start again... It's extremely better than any software removal tools.

• can't see time capsule, but can use the wifi and mount

  I have a 5th Gen (A1470) Time Capsule on our network. The WAN ethernet port is connected to a router. The TC has a static IP address, Wifi is enabled (on the TC) and router mode (bridged).

  I have hard reset the Time Capsule and reconfigured as above before you perform backups on all devices.

  We have two iMacs, two MacBook Pro and a Mac Pro (2009) backup fine both via ethernet (via a router and also directly in the transport CANADA ports) and connections Wifi of TC. One of the iMac running Yosemite the rest are El Capitan.

  However, I have an iMac on the WiFi network that cannot find the TC in the Time Machine or the Airport utility preferences. However, it can join the network Wifi of TC and attach it using the Finder. I've also disabled Wifi and iMac directly connected to an ethernet port on the TC, but he can't find it in the Time Machine or the Airport utility preferences.

  I followed the instructions from LaPastenague to Re: utility Airport can't find Time Capsule. I also reset the PRAM and SMC. No luck.

  The iMac is a 2011 model.

  I have an iMac on the WiFi network that cannot find the TC in the Time Machine or the Airport utility preferences. However, it can join the network Wifi of TC and attach it using the Finder. I've also disabled Wifi and iMac directly connected to an ethernet port on the TC, but he can't find it in the Time Machine or the Airport utility preferences.

  Just to check... what operating system is this iMac?

  You have ipv6 local link only the value... This is important.

  Make sure your network is running DHCP and DNS address is the same as the other computers.

  Make sure that the computer name is short, without spaces and pure alphanumeric characters.

  No luck, it's time to do a reset of the TM.

  Pondini instructions still work.

  I would remove plist Time Machine and redo the configuration... you don't lose the current backup... you may even do this...

  A4 here. http://pondini.org/TM/A4.html

  Honestly if that don't fix it... it is time to download and use Carbon Copy Cloner... because the TM became too difficult...

  Depending on what operating system you are on. TM has a version of command line... TMutils.

  I would like to confirm Apple it have not eliminated.

  I rarely use... I think that if it does not work via the installation of normal preferences... then it became time to use CCC which is what I do. Or run them both so I don't have a good backup.

  ne.html http://www.Macworld.com/article/2033804/Control-Time-Machine-from-the-Command-Li

  Some commands should be useful just to see the installation program.

  for example

  tmutil destinationinfo

  > ==================================================

  Name: TimeMachineBUP

  Type: network

  URL: afp: / /; AUTH = none % 20User % [email protected]/TimeMachineBUP

  ID: CFD5ED31-5884-47E7-8575-D29F65C044D8

  ====================================================

  Name: data

  Type: network

  URL: afp://Ray%20H; [email protected]/data

  ID: 2FB1A587-CD30-4A62-A4E3-2743C9C22469

• Our time capsule will blink a light amber and utilities said that it is overheating. What is the problem?

  We had a problem with our (less than 2 years) time capsule - the light yellow flashing, the fan runs often and looking in "utility" on my mac, it says that it is overheating. What is the cause of this?

  The Time Capsule fan runs constantly, so you shouldn't be aware of the fan running on the time Capsule 'often'.

  If you receive a message that the Time Capsule is overheating, there is probably a problem with the internal power supply on the Time Capsule.

  If you have an Apple Store near you, it would be wise to take the time Capsule to let the experts check the issue and discuss your options.

• can't see the time capsule on network

  I have a router modem wireless method

  2.5/5.0 and I want to continue to use the wireless installation.

  I am up-to-date on El Capitan.

  The router via ethernet is an express airport 2nd generation connected to an amp for antenna and in addition to the express via ethernet is a time capsule of 3rd generation? in a press room feeding a number of multimedia devices.

  What I want to do is to backup my Mac Book Pro on the time capsule which I see in the finder, but not its content, nor I see

  It is contained in Time Machine.

  Can someone help?

  It can be very difficult if not impossible... or only very little reliable if you do not connect the computer directly to the TC...

  Anyway... have a go... find the IP address of the TC of airport utility... no chance then don't first plug the computer by ethernet directly to TB. Use Thunderbolt for the ethernet card if your mobile phone is failed.

  Once you have the IP address... Use the top Finder menu... Go, connect to the server.

  Type AFP://10.1.1.46 (substitute your real IP of the TC).

  When the connection is done put the password and save in keychain.

  It will work up until the IP... Therefore, force is not to change.

  Still had problems give me a screenshot of the airport with the pages of summary of the Express and the TC utility.

• How to listen to a couple of times (with different names) table in another schema?

  Hello guys,.
  
  I replicate a table schema (SCH_1) (TAB_1) on the basis of data source (named DB_1) twice on the schema (SCH_2) on the basis of data target (DB_2) with two different names (TAB_1 and TAB_1_SHORT). TAB_1_SHORT on db target must be a subset (eg. WHERE STATUS = 1) of TAB_1!
  
  How to do? can someone help me?
  
  I tried to realize that in this way:
  
  (1) creation of 1 capture process with the rule 1 table on source db (without any rule of subset to capture all changes) for table TAB_1
  
  (2) creating a process of spreading with no rules
  
  (3) creation 1 apply the process with a rule in table for table TAB_1 without any subset_rule but with the transformation of the pattern of SCH_1 to SCH_2 (DBMS_STREAMS_ADM. RENAME_SCHEMA) = > it works correctly!
  
  (4) creating a subset_rule (WHERE STATUS = 1), a transformation of the pattern of SCH_1 to SCH_2 (DBMS_STREAMS_ADM. RENAME_SCHEMA) and a transformation of tablename from TAB_1 to TAB_1_SHORT (DBMS_STREAMS_ADM. RENAME_SCHEMA) for table TAB_1_SHORT = > does not work, no errors posted in dba_apply_error!
  
  in another chance, I tried to turn the table and the schemaname in the process of capture, with the effect that my first table TAB_1 would not be listened to again.
  
  I don't know what the problem is. I think it must be possible to publish a table for two different targettables in the same pattern on an another db, is not it?
  
  I hope that the greetings
  Flo

  Hello

  Adding a normal table rule and also a subset rule would not work because the rule would be evaluated only once in the set of positive rules. If the normal rule is evaluated first, then the subset rule and the rest of the rules would not be assessed at all that's why it would not work.

  This can be done using one of the following methods:

  Method 1:

  1 use the declarative transformation on the capture/apply and rename SCH_1 to SCH_2 scheme.
  2. now, on the site apply, define a DML for SCH_2.TAB_1 Manager
  3 al ' DML Handler, do the following:
       
  a. get the value of the STATUS column
  b. check if the value of STATUS = 1, if yes, then change the name of the object to TAB_1_SHORT and run the LCR.
  (c) another thing not to change the name of the object (leave it as it is, TAB_1) and run the LCR.
            
  Method 2:

  1. Add a DML for SCH_1.TAB_1 Manager
  2. in the DML handler perform:
       
  method of set_object_owner use of LCR$ _ROW_RECORD to rename the owner at the SCH_2
  b. get the value of the STATUS column
  c. check if the value of STATUS = 1, if yes, then change the name of the object to TAB_1_SHORT and run the LCR.
  (d) another thing not to change the name of the object (leave it as it is, TAB_1) and run the LCR.

  Please let me know if you need examples of code.

  Thank you
  Florent

• SkyDrive, Office 365, and Windows 8 with different user names

  A few months I bought Office 365, put him on a victory. 7 computers and Office Open using a Gmail account for my user ID (do not have a live account). Office / Skydrive works very well. Just bought a new victory. laptop 8 and open a real account to connect to the new laptop. The Live username is my login Win 8. The skydrive on the default values of portable Win 8 new a account linked to the new Live user name empty Skydrive. How can I get the new victory. 8 portable by default to the original Skydrive with gmail (many docs in this Skydrive) username?  I am looking for a long term solution. Should I "Rename" the account Office 365 for the new Live account? Can I use the login gmail as my victory. Sign in now and all the future widows editions years on the road? Thanks a lot for your help!

  If you use your ID gmail to access skydrive, it's already your microsoft account.  (a microsoft account is not linked to a particular area such as outlook.com, hotmail.com or live.com).  your @gmail.com can also be your microsoft account.

  That said, you can use your id gmail for everything (the computer connection, skydrive account) and stop using the new microsoft account, you just created, or you can set up skydrive just to use your gmail account and continue logging in to your computer with the new microsoft account.

  to activate the skydrive account, launch skydrive, reveal the charms bar (move the mouse to the lower right), click settings, click options, and then click the logout button.  next time you start skydrive, you will be asked to log in.  Sign in with your gmail id and your password.

• 3.2.5 and Postgres Tables with case names mixed

  I have a server postgres 8.2 with tables that have mixed case names such as: UserTableName
  
  3.2.5 the hyperic server is not able to configure these follow-up tables:
  
  Configuration properties
  
  The configuration has not been set for this resource due to: invalid configuration: Error retrieving value: n_tup_del
  
  "I tried to put the name of the table in ' ' and escaped-" identical to the good, but no luck... of ideas?

  Hi Jaime,

  I can confirm the bug. It is still a question on 4.0.2 and Postgres 8.3

  Please report to us. I'll create a bug report.

  See you soon,.
  Mirko

• Difficulty from a database and the connection with the name of user and password

  Hello
  
  I have an oracle 9i installed on RHEL4. But I got the following errors when you try to connect by using SQL. So I'm not able to connect to the DB, or start the DB.
  
  * $ sqlplus /nolog *.
  
  SQL More: Release 9.2.0.1.0 - Production on Tue Nov 11 14:23:13 2008 *.
  
  Copyright (c) 1982, 2002, Oracle Corporation.  All rights reserved.
  
  SQL > connect / as sysdba
  ERROR:
  ORA-01031: insufficient privileges
  
  
  SQL > connect system/manager
  ERROR:
  ORA-01034: ORACLE not available
  ORA-27101: shared memory realm does not exist
  Linux error: 2: no such file or directory
  
  
  SQL > connect system/manager@xxxxx
  ERROR:
  ORA-12541: TNS:no listener
  
  The last error says no listener. But according to me, the entries in the file /home/oracle/app/product/920/network/admin/tnsnames.ora correct and valid. I gave the HOST entry as the IP address of the server area.
  
  Y at - it suggestions or tweaks to get rid of these.
  
  Thanks in advance.

  Try unset TWO_TASK

  at the beginning the sqlplus or try

  SQLNET. AUTHENTICATION_SERVICES = (ALL)

• use time capsule 4th generation to extend the network

  Can I use the time Capsule (4th generation) to extend a network? I would like to connect via Ethernet to a router (Belkin) of non-Apple. Thank you.

  -> Belkin router-> Ethernet cable modem-> Time Capsule-> wifi network products in another part of the House

  Yes, it works perfectly.

  The TC will be in bridge mode...

  

  The wireless will be defined to create a wireless network.

  You can use the distinct name to the Belkin Wireless... or you can use a name identical to the Belkin with identical password wireless and security setting... This is called roaming network, so in theory, you can wear around your wireless devices and they swap "tours" as a mobile phone... Sounds good in theory... a little less than the sum of the parts actually.