To control the line of sequences in the internal requests imported

Similar Questions

• SMU-6556 - how to control the rise in digital lines (hsdio) time

  Hello

  Is it possible to control the rise in digital lines SMU-6556 time?

  Even in a low frequency 10 kHz signal rise time is 2ns.

  TKS,

  Hello engfpe,

  The SMU-6556 is a 50 Ohm system, which means that the output is source series finished to be 50 Ohms and all our cables and accessories are 50 Ohms.  With this configuration, regardless of the flow of data, you should have a clean edge up or down, regardless of the data rate. The quality of the production (edge up or down) on your device is related to the adaptation of impedance of your cables.

  The SMU-6556 cannot adjust the speed of scanning by itself.  However, you can insert simple passive components to do it for you.  I have attached below the images.  The first is a diagram showing a way to slow down the edge.  The second is the a waveform simulation showing the rate of original edge before it slows down and the edge of idle.   This simulation is not the SMU-6556 but rather a generic digital output for concept.  In the schema that R1 is set on 34 Ohms because U1.8 has the 16 additional Ohms on the inside.  TL1 is the output of 50 ohms simulating the cable on the SMU-6556.  R2, R3, and C1 are components, you can insert after the SMU-6556 twist before moving your device/cable.  In this configuration from cable to your device is TL2 which is also 50 ohm, but it could be another impedance in which case you would change R3 to match.

  You can see in the attached images, you can slow down significantly the edge with this configuration by altering the C1.  I hope this helps.

• How can I control the elements in the graphic palette (profile line) via the property node?

  Hello everyone,

  Is it possible to control the elements (graphic palette in the profile of the line) via the property node?

  Greetings zapfle

  In general, you must balance only Min/max property, then you can "zoom and Pan" by program:

  

  Andrey.

• What is fledge command-line argument to control the graphics acceleration?

  Is there a command line argument to control the graphics acceleration for a JDE 5.0 Simulator?

  I would like to switch off in the command line so I can add it to the Simulator Run Eclipse IDE and the debug configuration.

  I checked their moult imaginal/Help and I have not found any that I could see that it works.

  Thank you.

  The settings are stored in a file located at

  \Documents and Settings\ [windows login name]\net\rim\fledge-2\fledge-saved.conf

  At the bottom of the appearance of file for the line:

  4
  

  Change the number 0 for no acceleration.

• How to control the number of lines of text below the image in the slideshow module?

  Lightroom 3.3

  How to control the number of lines of text below the image in the slideshow module?  I have an image with 36 words in the caption field which exports like two lines GOOD.!  I have another image with 57 words in the field of legend who runs the page and shows only a VERY BAD line.  With 57 words I can't do the single-line text box small enough to keep the text does not spread out of the page.

  Ideas?

  On the Mac platform and I expect similar under Windows, just hit enter or return key will not help. Instead, you will have to hit the keys Ctrl + Enter or Ctrl + return. This forces a new line. Windows may use a different modifier key. The screenshot below shows that it is possible. Unfortunately, you need to add the text via the caption or Description field in the library module.

  

• How to use Labview to control the motorized turntable?

  Hello

  I am new to Labview and do a project that requires the use of labview to control the motorized turntable (XYZ axes). I need to use the Labview programming and have no idea at all. Need help, thank you very much!

  Lei,

  Everything said by others is correct and to do because they describe, at a given time. But I always approached these projects of motion control first by looking at the 'motion controller' (I hope you have a) and 'drivers' (what you need) between the computer/LabVIEW and engines decide what communications will be required for these devices and get an idea of the syntax of command and the language to use with them.  In some cases, the controller and the motor driver are integrated in a single unit. Heck, in some cases, they are even integrated with each engine.

  The motors can be the stepper motors or perhaps servomotors.

  In the case of drivers stepper (devices that provide power electronics to run the engines), many of them are run using only two control signals for digital called 'step' (a pulse train) and 'direction' (high-low level) and if it is possible to generate directly with the PC, it's an order of magnitude easier (if you have not already a library of available motion control to manage the generation of these signals and) the execution of the stepper motors) of having a "Motion Controller" between the PC and the "motor".  Engine drivers step by step usually can be configured that current engine and the size of the stage and sometimes for the other plus-moteur/driver-parameter setting. The configuration of these can be made with jumpers, switches or, for some drivers, with orders ASCII on some sort of port of communication, but in general these are values you download the installer once at the beginning and then never touch again if you do not need generally to have a full time available on their change communication path.

  In the case of the actuator drivers (once again the devices that provide power electronics to run the engines), many use a +/-10V control input analog signal, and, again, while it is possible to generate the signal directly with the PC hardware, a separate axes controller is usually much simpler and more robust.  In the case of a servo system, there is also a signal back to an encoder or resolver attached to the engine to be used by any device will exercise the motion controller in the system.  There are once again associated with the driver configuration parameters (and controller in this case, since it is part of the servo feedback loop) which must be configured at the start but once set up properly, they rarely need to be changed again.

  A movement controller which is separated from the PC often manage several drivers, and can often coordinate a movement between them. It will load the rise up/down of the engine speed as that changes. It will be followed by position of each motor. The servo system, but it will take the feedback signal and use it to adjust the speed/position/torque of the engine. The motion controller also deal with race and home or index of signals is usually on most lines of movement and provide information of the State of the switch to the PC.   To run the motor controller is then just a matter of chaining a set commands of (usually ASCII) to indicate how fast to run and how far to go (and direction) and by sending a command "do it." Then, ask you to keep track of the status of the process and the States of the switches.

  In many cases the builders of controllers of movement are a primitive way to communicate with the controllers of a PC with no additional software other than what they offer. With this you can at least have an idea of how different the controller commands and responses they produce. That you can start to build sequences of commands to perform the actions you want.

  You can then add LabVIEW to the mix and to understand how you can get it to send sequences of similar orders on the paths of communication that are available and respond intelligently to the information it receives in return for motion control.

• How can I control the gif animations?

  I have a project where I need some animations. The animations, that all have been created in After Effects. Now I can use png sequences, but these are very big and I need much the animations running on the same time. So I prefer to use gif animations. So my question: I can control when to play the animated gif but I can't play more than once. Is there a solution?

  Thanks for responding!

  Jannis

  Hello

  I see... you control when it displays. Technically, this is not the same thing that control the animated GIF; you just control when you see it. EA only recognizes GIF as image format and can not make the browser plays from the beginning as the first time that it is displayed or when it performs a back loop (if your animated looping GIF).

  However, you could do something similar with an additional image file or two, jQuery and css background-image "load" the GIF file into a transparent image. Here is a link to an example that always runs the GIF animated from the beginning:

  https://creative.Adobe.com/share/52f15194-875B-4604-8857-9b9bf5f78e04

  A single line of code that does the work is in the playBtn click handler.

  HTH,

  Joe

• I want to open links, I click on to appear among the tabs at the end (to the right) of my browser. Is there a way to control the order of the tabs?

  I find it confusing that when I click on a link, the new tab for this link opens somewhere in the middle of my line of tabs. I would have preferred that the new tabs would appear and the (right) end of the alignment of the tab. I see no way to control the order of tabs in Firefox. Is there a way to accomplish what I want?

  Type of topic: config in the URL bar and press ENTER.

  Answer Yes.

  Filter = browser.tabs.insertRelatedAfterCurrent

  Double-click this preference to activate it false.

  Then restart Firefox.

• ConfigFree: windows pop up message: sellers application is controlling the wireless network adapter

  Hello

  When I draw a line from nearby wireless networks (with or without WEP security) to the laptop in the middle icon,
  a popup message with the text: the provider application is controlling the wireless card.
  Does anyone know what this message or where I can get the answer to this question?

  After clicking on it you may see far (only the 'ok' button is available), the connecting line with the laptop wireless network disconnects after
  a few seconds.

  Thanks a lot for helping me...

  Hello

  In my opinion this message appears because a 3rd WLan utility configures and controls the WiFi connection!
  There are different possibilities:
  The laptop uses the Intel wireless network adapter and the Intel Proset utility configures the WLan
  Or
  The laptop uses the Atheros WLan card and Atheros Client utility configures the WLan
  Or
  The windows have the option has been enabled and do this job.

  In this case ConfigFree application cannot configure and control the WiFi connection!

• Control the Structure of the event with text file

  I'm new relativaly in LabVIEW (experience only about 2 weeks). I am currently control a stepper motor using a structure of the event. Similar to the sample code given by LIFA, I entered my settings how the engine not move away, then press a button on the windows before, and it works this way. I also have other equipment that works as well in LabVIEW, as a transnational step; all components operate individually.

  Now, I'm trying to make the more automated system and to ensure that all the different equipment work in the same code. So, I tried to implement a structure of the event using a text as an input file to try to control events. The text file has a table 1 d of numbers going down vertically (only the line numbers change). So, I used a table of index function to take the numbers one by one, use a loop (while loop in this example) to go to the bottom of the column of numbers. However, the event not register the change, even if the indicator shows the value is changing.

  Attached, it's my test code and the text file that I use to try to control the structure of the event. Please let me know what I am doing wrong. Thank you.

  Oh, now I understand what you tried to say. I'm using a loop and a case structure to activate different events with the entries in the table. I thought case structures and event were the same, but you taught me the event structures are used just for the façade stuff. Thank you all!

• To control the shutter SC10

  Hi all, I am an amateur and very new for driver, Labview, and programming with pilots. But now, I must create an amplification in labview to control the Thorlabs SC10 to the shutter. I try to read documents about Labview but not all count.
  Please tell me what can do starting from the connection to the writing of this aplication!
  I think I'm in the despair of my quality
  Thank you very much for your help!

  My e-mail address: [email protected]

  This link to shutter SC10:

  http://www.mediafire.com/?ctjdc32nqpzhkbw

  Hello

  According to the manual, SC10 shutter can be controlled with a RS-232 connection.

  So the first step is to build (or buy) the cable if you don't already have in order to connect the shutter to the PC.

  Then, in LV, you will need to learn how to send messages to RS - 232. You can do it with the functions of the VISA. Search for "RS232" in the finder example LV.

  To learn to communicate in RS - 232, you can also connect 2 PC together, send message with LV and receive with the Windows Hyperterminal.

  Then he must know exactly the syntax of messages RS-232 you must send to the shutter (each instrument has its own set of 'orders').

  Finally, you will code the application LV using while/for loops, the sequence structures, structures case...

  Good luck!

• Is there a way to control the fonts used by a remote façade displayed in a browser?

  When you use a web browser (on a system with only the TEN LabVIEW installed) to monitor a remote façade commissioned from a cRIO is a way to control which fonts are used by the browser when it displays the Panel?  In the case of a stand-alone executable, I know that you can include definitions of fonts associated with the executable 'appfont' and 'FPfont' in the INI file to control the fonts used by the executable. Is there something similar that can be done with a front panel running in a browser window?  Or do I go through the VI and explicitly define a non-generic font specific for each control and indicator that is displayed?

  What is the size of fonts in windows on the PC?  It has 125%?

  Your problem is similar to that discussed in this thread.  Set a Date and hour - week 5 months does not last line

• How to dynamically control the index of an array

  Hello

  In fact, I have two request:

  1.

  I want to create a table with different size? According to the user request!

  So I would like to be able to set the index of the table, which allows the user to have his picture with a different line is array (1 d)!

  On my test will affect the number of line by another application (a loop used in another part of my request)!

  2 / is it possible to have two loops 'for' this command at the same time, a loop of the sequence (with indexation)?

  TX

  
  

• DAQmx how to control the level of tension AO paused for a relaxing break?

  I have an application where I need to generate a waveform of a fixed frequency (~ 200 kHz) and the amplitude, but for differing them burst lengths and different lengths of time between bursts. These bursts and these delays are controlled by a line of DIO to generate the relaxing break. I also need to have the output voltage analog voltage controlled between bursts of waveform. I explored using various trigger options, the break seems to be the best solution, but I'm difficult to control the particular point of the end of the waveform during the break occurs to make sure that the break is at the same specific voltage when the wave is hidden. I try to adjust the position of the example 'Analog output Pause for the periodic Signal with regeneration on specimen' but cannot get regular tension during the break I'm after. I use a card Series DAQ. X is there a simple way to pre-set the tension that will be broadcast during the paused state when using a relaxing break? I was not able to find it in the examples or documents. I can't use the code of reference AO set example because it is a software-driven and does not fit into the model of schedule I need to generate.

  Hello

  I don't think there is a way to establish a certain level on the analog output, based on a relaxing break.  I watch using a redeclenchables task analog output and do every hour of beginning to the required voltage.

• Control the order of execution of the init/release

  I have a small program that I write in LabView.  It has an API (one set of screws to wrapping the functions of the DLL to control a device).

  Other such programs in the Gayshop make liberal use of the structures of the sequence.  I understand that the sequence into LabVIEW structures are not usually recommended.  I am writing my program with the best style of LabVIEW (as far as I understand - I'm still a relative novice in LabVIEW).

  I found that I could wire together the error / mistake Terminal to create a data flow to control the order of execution and it works beautifully.

  However, there are some cases where it is not enough.

  Here is an example.  I hope that the answer to this will answer my other questions.  If this is not the case, perhaps that I'll post more.

  One of the first live I call is an Init function.  One of the last screw is the release function.

  The release function must be called at the end, after the rest of the program executed (in this case, it is after the user requests the stop).  It should be naturally at the end (or almost) of the error string in / out connections error (as it is currently).

  However, the error it receives, which will determine whether or not he will run, should be the output of Init.  Release should work even if something else has failed.

  I enclose a photo showing the problem, with most of the code snipped out (as exactly what is happening in the middle is not relevant).

  What is the elegant way to handle this in LabVIEW.  Is it really a deal for a structure of the sequence, or is there a way more pleasant or better?  How would you recommend handling?

  Thank you very much.

  BP

  I agree with what pincpanter said, more you will need to use the status of the function 'Init '.

  Note that you can ignore the error and make the merger within the Vi version if you wish.

  Steve