try to increase the memory and speed up my computer

Similar Questions

• have dell dimension 2300... try to increase the memory... bought 512 MB memory card "valid dell"... no problem, should I expect once I installed?

  anyone has similar experience

  Make sure that the new card is correctly installed in the memory location.  If it isn't, the computer may not start.

  Enter the BIOS Setup program, and check that the BIOS sees the right amount of memory.  Start Windows XP then go to Control Panel > System and check that Windows detects the right amount.

• sound recorder, no not enough memory available to complete this operation. Quit one or more applications to increase available memory, and then try again.

  I tried to use sound recorder to test a microphone and it came with an error message after pressing the record and then he said, sound recorder, not stop not enough memory available to complete this operation. Quit one or more applications to increase available memory, and then try again. This issue is out of nowhere because he has never had this problem before. It's a brand new computer that ive built from the bottom up, and I have 4 GB of memory. only a little more than 2 is actually identified by windows xp, however. Ive looked in the Task Manager and it says I have 2 GB of free, so I don't know what to do

  Hi superconfused123,

  This problem occurs because of a design limitation in the tape recorder.

  You can check the link below: you receive a "not enough memory to complete this operation" error message when you try to record a .wav file using sound recorder: http://support.microsoft.com/kb/284893

  With regard to:

  Samhrutha G S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Unable to increase the CPU and memory in vRA in the Server tab billing information is not responsible to reconfigure

  Unable to increase the CPU and memory in vRA in the Server tab billing information is not responsible to reconfigure

  Please make the task below

  1. go Vcenter and check what VLAN is assigned note this number of VLANs

  2. go on the reservation tab and in the network profile enable VLAN

  3 do this data collection

  4. they that you try to configure the processor and memory, that it should work

• Can I replace the memory and not lose what is on the old memory for a Mid 2007 Mack computer desktop Intel Core 2 Duo, 2 GHz processor speed, 1 CPU, 4 MB of Cache L1, the 4 GB memory at 800 MHz bus speed.  Only 1 slot can play memory, the other is damaged

  Can I replace the memory and not to lose what's on the memory of the former?  I have a Mid 2007, 20 "desktop Mac, Intel Core 2 Duo, 2 GHz processor, 1 CPU, 4 MB L2 cache, 4 GB of memory, 800 MHz bus speed.  I have a backup device.  A RAM slot is damaged.

  You are confused of RAM and disk space available.

  RAM stores information temporarily while the Mac is enabled and the application is reached. RAM replacement has no effect on the long term of your information storage.

  The hard drive is where your information is stored in the long term. If you replace your hard drive, you need restore the information from a backup.

  FYI, for your iMac, the maximum RAM is only 6 GB.

• I would like to know how to get a debugger and how to increase the memory on my computer of mocarosoft 7 HP

  I tried to find information on the question of the debugger, but I'm at a total loss about how to increase the memory of the computer.  Please help me, because I have school work on this 'thing'.

  The Windows debugger is included in the SDK

  http://www.Microsoft.com/en-US/Download/details.aspx?displaylang=en&ID=8279

  http://msdn.Microsoft.com/en-us/Windows/hardware/gg463009.aspx

• Satellite L300 PSLB8E - how to increase the ram clock speed

  I have a laptop which is equipped with 2 slots for ram PC2-6400
  1 - Samsung module M4 70T5663QZ3-CF7 [800 MHz] 2GB
  2 - Samsung module M4 70T2864QZ3-CF7 [800 MHz] 1 GB
  GPU: Intel GM45
  Processor: Intel Core 2 Duo T5870 Mobile @ 2000 MHz
  According to the manufacturer, this kit allows you to work with the 667/800 MHz memory speed, but the problem is that reference programs show the actual frequency of the ram at 399 MHz.

  Question No. 1:
  (a) why not clock the memory works in 800 MHz but only 399 MHz,
  (b) how to change to a 800 MHz

  Question No. 2:
  I'm going to buy a processor
  Penryn Core 2 Duo T9600 processor (1066 MHz FSB) (2.80 G) Hz or T9400 (2.53 G)
  and install it in the computer
  and increase the memory of 2 x 4 GB 800 MHz (8 GB)

  I explained that this possibility is provided for by the manufacturer according to the Maintenance Manual for:
  Toshiba computer
  Satellite L300/L305
  Satellite Pro L300
  EQUIUM L300
  SATEGO L300
  (PSLB8x/PSLB9x)
  (PSLBAx / PSLBBx)

  If this operation will help to improve system performance

  I put t know what programs you use and if it is good or not if this info can be good and perhaps not. I put t know. The fact is that you n t have one any influence on the functionality of memory and I doubt that you can do something and change some values.

  Exact specification for laptop laptop does not for me but I think that Satellite L300 must have Intel GM45 chipset and I presume that for your motherboard FSB is 667 MHz. You can improve up to 8 GB and compatible 4 GB RAM module has PA3670U-1M4G part number.

  Upgrade CPU on Satellite L300? I put t know man. A friend of mine has this model of laptop and I don t know if it's the right decision to spend money to upgrade this old model of laptop budget.
  http://APS2.toshiba-tro.de/KB0/TSB9401AX0001R01.htm

• Explorer.exe increases the memory usage

  Original title: Explorer.exe constantly increasing memory size... Windows 7 Pro 64-bit run on Lenovo Edge 73 i5 - 4570S / / 4 GB RAM / 500 GB HDD / PC Deskstop

  Dear support,

  Kindly help me on this issue.

  1. when I just reformat the PC and load back the OS (Windows 7 Pro 64-bit) and install dropbox version 3.0.5.

  2. then the explorer.exe constantly increasing memory size until the entire screen freezes.

  3. I had to install kaspersky version 10 with license and Malwarebyte s virus scan and to... etc... Once the scan is not virus on this PC.

  So now, what can I do on this issue?

  I need your help... I did it several time reformatting also have a question...

  Thank you and best regards.

  Scofieldbee88

  Hello

  Thanks for posting your query in Microsoft Community.

  I understand that explorer.exe increases the size of the memory and the screen freezes. I'll be happy to help you with your query. Let me ask you;

  1. When was the last time it was working fine?
  2. You did it no particular change in the computer before the show?

  The issue could be related to any recent change in software or hardware on the computer or any third-party software conflict. In addition, it is recommended that you use unique security software at a time so that he would not come into conflict with other firewalls.

  We will follow the methods below and check.

  Method 1: Run the troubleshooter of Performance.

  To optimize the performance of Windows, try to use the resolution of Performance problems to automatically find and fix problems. The resolution of performance problems check issues that could slow down the performance of your computer, such as how many users is currently connected to the computer and if multiple programs are running at the same time.

  Open the performance troubleshooting utility by clicking the Start button , and then click Control Panel. In the search box, type troubleshooting, and then click Troubleshooting. Under system and security, click check for performance issues.

  Method 2: Start the computer in safe mode, and then perform the clean boot in order to avoid any conflict of third party software.

  Step 1: Start the computer in safe mode.

  See: , start your computer in safe mode

  Step 2: Perform the clean boot

  Put your system to the clean boot state helps determine if third-party applications or startup items are causing the problem. You must follow the steps in the article mentioned below to perform a clean boot.

  How to perform a clean boot in Windows

  Note: see 'How do I reset the computer to start normally after a boot minimum troubleshooting' to reset the computer starts normally after troubleshooting.

  Additional information:

  Optimize Windows performance

  Hope this information is useful. Please feel free to answer in the case where you are facing in the future other problems with Windows.

• Today, we are locked into sitting and staring at the stupid hourglass or spinning cirlces infinite so that your OS continues to steal the memory and performance

  I just want you know I hate using this operating system. WIN 7 and WIN 8 on different computers. Years ago the opportunity to correct a bit your * but today we are locked in to sit and watch the fool or spinning cirlces infinite hourglass while your OS continues to steal the memory and performance of any type of material that is using your operating system. I can't wait to own a computer that runs an operating system that doesn't degrade not just because I use it for work and play. There is a special place in * for windows programmers and engineers.

  Original title: why windows suck so bad!

  Hello

  These should help:

  Ways to improve the performance of your PC
  http://Windows.Microsoft.com/en-us/Windows-8/improve-PC-performance

  Maintenance & performance
  http://Windows.Microsoft.com/en-us/Windows/performance-maintenance-help#performance-maintenance-help=Windows-8&V2H=win7tab1&V3H=winvistatab1

  Crashes Windows or freezes
  http://support.Microsoft.com/kb/2681286

  How to speed up your PC
  http://support.Microsoft.com/kb/2746761/en-us

  =======================================================

  You use a 3rd party antivirus/antispyware/security program? If so many people
  can cause slow start from the bottom.

  Check with the support of the system Maker (manufacturer of motherboard for customized systems), their
  online resources and the drivers and ask questions in the forums about known problems.
  Updating the BIOS , drivers of low level chipset and embedded and separate major
  device drivers (anyone who can have an impact on the speed of startup and performance).

  Note the use of Win Key + X and Win Key + W (to go on the Control Panel, Run and parameters
  According to needs). Win + D key calls the office and using Win Key active / disable the office and
  Splash screen.

  Check startup programs.

  Right-click in the left lower corner - Manager of tasks
  Or Windows key + X - Manager of tasks
  Or right click on the taskbar - task manager

  Check the Startup tab.

  More troubleshooting:

  How to perform a clean boot for a problem in Windows Vista, Windows 7,
  or Windows 8
  http://support.Microsoft.com/kb/929135

  Other programs to help:

  Autoruns - free - see what programs are configured to start automatically
  When your system boots and you connect. Autoruns also shows you the complete list
  Registry and file locations where applications can configure auto-démarrer parameters.
  http://TechNet.Microsoft.com/en-us/sysinternals/bb963902.aspx
  Process Explorer - free - find out what files, registry keys, and other objects
  processes have open, which DLLs they have loaded and more. This unique
  powerful utility will show you even owned by each process.
  http://TechNet.Microsoft.com/en-us/Sysinternals/bb896653.aspx

  =======================================================

  If necessary:

  Try to do a "Refresh your PC without affecting your files" (or modification of your personal data
  settings) or even a restore. Be prepared to re - install the programs, applications will remain.
  And having redundant backups of your files on the disk main hard is always a
  good idea.

  Windows 8 includes special discount methods (keep files and settings) or a reset
  (new installation remove all).

  How to restore, refresh or reset your PC
  http://Windows.Microsoft.com/en-us/Windows-8/restore-refresh-reset-PC

  How to create a system image to refresh your PC in Windows 8
  http://support.Microsoft.com/kb/2748351

  How to update Windows 8
  http://www.eightforums.com/tutorials/2293-refresh-Windows-8-a.html

  How to reset Windows 8
  http://www.eightforums.com/tutorials/2302-reset-Windows-8-a.html

  If you need a repair disc:

  Create a system repair disc
  http://Windows.Microsoft.com/en-us/Windows7/create-a-system-repair-disc

  How to create a "system repair disc" (CD/DVD) in Windows 8
  http://www.eightforums.com/tutorials/2855-system-repair-disc-create-Windows-8-a.html

  How to create a recovery USB in Windows 8
  http://www.eightforums.com/tutorials/5132-recovery-drive-create-USB-flash-drive-Windows-8-a.html

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">

• How can you increase the memory in the VM VCenter?

  I have just ESXi 4.1 Essentials. I have to close the virtual machine to increase memory and if I stopped it, then I can handle is no longer the VMs (which is a).  I had a hand on a part of the installation and configuration of the environment but you can try to provide as much additional information as needed.

  
  

  Hello

  Launch a vsphere client directly to the host than US having the vCenter server VM and stop of the VC and increase the memory to the VM and turn on. ?

  Let me know if this does not answer your question.

  Thank you

  Avinash

• Can I increase the memory on my old Satellite Pro P100?

  I have a Satellite Pro P100 (P6PA4E-002001EN) with only 512 MB of memory and the desire to know if it can be increased and if so what memory should I buy and it is easy to open the machine and adapt?

  Hello

  You can increase the memory on this laptop amazing plu of 4 GB of RAM.

  RAM modules compatible that you can use to upgrade:
  PA3511U - 1 M 51 (Kit of memory 512 MB DDR2-667)
  PA3512U-1M1G (memory 1 GB DDR2-667 Kit)
  PA3513U-1M2G (memory 2 GB DDR2-667 Kit)

  Check the underside of your laptop and there should be probably set with a cover of Ram screw. Remove it and you will have access to the memory locations.

• How to increase the memory of the phone to the xperia neo L?

  Hello

  I use the phone Xperia Neo L and I am facing many problems due to the internal memory. At first, I thought this could turn out to be this big problem, but now I am unable to update stuff on my phone because it is already filled with lots of updates. I moved all the mobile apps on my SD card and now I find myself with no memory of the phone even install xperia updates. Is it possible to increase the memory of the phone. Please help me with the problem.

  Thanks in advance.

  Greetings asifsk1992!

  At your convenience, please join our colleagues in Sony Mobile for assistance with your question. You can attach them to this site: http://www.sonymobile.com/global-en/support/contact-us/contact-info/.

  Thank you for your message today!

• I want to increase the memory on the 2210CDS Satellite

  I have an old Toshiba Satellite 2210CDS/6.0 I want to give to charity. Until I do, I wanted to increase the memory from 64 MB to 128 MB minimum, because he seems excessive paging of memory under Windows 98, it slows down a lot too.

  The original 64 MB memory module is marked PC100-222-62, Toshiba p/n THLY6480H1FG-80. I ordered since equivalent barrettes memory 128 MB (PC100-222-620) from different sources. They fit well, but the memory is still limited to 64 MB, as evidenced by the page to configure the BIOS and Windows pages 'system '.
  The computer has only one memory location. What I am doing wrong?

  Ruud Hartog

  Hello

  This laptop is very, very, very ;) old

  However, the laptop can be improved up to 160 MB. 64 MB internal memory + 128 MB additional memory module

  The Toshiba recommend using these modules:
  128 MB - PA3005U
  64 MB - PA3004U

  Usually after upgrading the BIOS should automatically recognize the module.

• Equium P200D - how to increase the memory of the GPU?

  Hello

  I have a portable Satellite P200D-139 and I was wondering if there is a way to increase the memory of the GPU?

  This model of laptop is not known to me, but if there are shared memory graphics card you can extend it if you upgrade RAM.
  Check the specs of the laptop and see what amount of RAM max for this model of laptop is. I assume it must be 4 GB.

  By the way: check http://forums.computers.toshiba-europe.com/forums/thread.jspa?threadID=43021

• Should we leave how much free space on the C drive before affecting the performance and speed?

  Hello!

  Hard drive of my new PC (C) is 1 TB (processor Samsung 7i, Windows 8.1). It doesn't have any other disk/partition. How this space is safe to use to store large files (videos, esp., stored in the native video library file) without harming the performance and speed?

  And if I create another partition (D) and just use it for storage, it will make much difference compared to the above?

  Thank you!

  Anna

  Sunday, March 1, 2015 10:59 + 0000, AnaFilipaLopes wrote:

  And if I create another partition (D) and just use it for storage, it will make much difference compared to the above?

  Planning your Partitions

  The Question

  Partitions, how much should I have on my hard drive, what do I use
  each of them for, and what size should each one be?

  It s a common question, but unfortunately this doesn t have a
  only simple, just answer to all the world. A lot of people will respond with
  the way they do, but their response isn't necessarily best for the
  person seeking (in many cases it isn't right even for the person)
  response).

  Terminology

  First, let's rethinking the terminology. Some people ask "should I".
  partition my drive? That s the wrong question, because the
  the terminology is a little strange. Some people think that the word
  "partition" means divide the drive into two or more partitions.
  That s not correct: to partition a drive is to create one or several
  partitions on it. You must have at least one partition to use
  He who think they have an unpartitioned disk actually
  have a player with only one partition on it and it s normally
  Called C:. The choice you have is to have more than one
  partition, not that it's the partition at all.

  A bit of history

  Back before Windows 95 OEM Service Release 2 (also known as Windows
  95 (b) was published in 1996, all MS-DOS and Windows hard drives have been set
  using the file system FAT16 (except for very tiny to aid
  FAT12). That 16-bit only because were used for addressing, FAT16 has a
  maximum 2 GB partition size.

  More than 2 GB of hard disks were rare at the time, but if you had
  one, you must have multiple partitions to use all the available
  space. But even if your drive was not larger than 2GB, FAT16 created
  Another serious problem for many people - the size of the cluster has been
  more great if you had a larger partition. Cluster sizes increased from 512
  bytes for a partition to no greater than32Mb all the way up to 32 KB for a
  partition of 1 GB or more.

  More the cluster size, the space more is wasted on a hard drive.
  That s as space for all the files is allocated in whole clusters
  only. If you have 32 KB clusters, a 1 byte file takes 32 KB, a file, a
  greater than 32 k byte takes 64 k and so on. On average, each file
  about half of his last group waste.

  If large partitions create a lot of waste (called "soft"). With a 2 GB
  FAT16 drive in a single cluster, if you have 10,000 files, each
  lose half a cluster of 32 KB, you lose about 160 MB for relationships. This s
  back in an important part of a player that probably cost more than $400
  1996 - around $ 32.

  So what did the people? They divided their 2 GB drive in two,
  three or more logical drives. Each of these logical drives has been
  smaller the real physical disk, had smaller clusters, and
  so less waste. If, for example, she was able to keep all the partitions
  less than 512 MB, cluster size was only 8 KB, and the loss was reduced to a
  a quarter of what it would be otherwise.

  People partitioned for other reasons also, but back in the days of
  FAT16, it was the main reason to do so.

  The present

  Three things have changed radically since 1996:

  1. the FAT32 and NTFS file systems came along, allowing a larger
  partitions with smaller clusters and so much less waste. In
  with NTFS, cluster sizes are 4 K, regardless of the size of the partition.

  2 hard drives have become much larger, often more than 1 TB (1000 GB) in
  size.

  3 hard drives have become much cheaper. For example, a 500 GB drive
  can be bought today for about $50. That s 250 times the size of this
  Player 2Gb typical 1996, about one-eighth of the price.

  What these things mean together which is the reason to be old to have
  multiple partitions to avoid the considerable wastage of disk space left.
  The amount of waste is much less than it used to be and the cost of
  that waste is much less. For all practical purposes, almost nobody does
  should no longer be concerned about slack, and it should no longer be
  has examined when planning your partition structure.

  What Partitions are used for today

  There are a variety of different ways people put in place several
  scores of these days. Some of these uses are reasonable, some are
  debatable, some are downright bad. I'll discuss a number of Commons
  partition types in the following:

  1. a partition for Windows only

  Most of the people who create such a partition are because they believe
  If they never have to reinstall Windows properly, at least they
  He won t lose their data and he won t have to reinstall their applications.
  because both are safe on other partitions.

  The first of these thoughts is a false comfort and the second
  is downright bad. See the analysis of the types of partition 2 and 4
  below to find out why.

  Also note that over the years, a lot of people who find their windows
  partition that has begun to be the right size proves to be too
  small. For example, if you have such a partition for Windows and later
  upgrade to a newer version of Windows, you may find that your Windows
  partition is too small.

  2. a partition for installed programs

  This normally goes hand in hand with the partition type 1, a partition for
  just Windows. The thought that if you reinstall Windows, your
  installed application programs are safe if they are in another
  partitions is simply not true. That s because all programs installed
  (with the exception of an occasional trivial) have pointers to the inside
  Windows, in the registry and elsewhere, as well as associated files
  buried in the Windows folder. So if Windows, pointers and
  the files go with it. Given that the programs need to be reinstalled if Windows
  the fact, this reasoning to a separate partition for programs not
  work. In fact, there is almost never a good reason to separate
  Windows of the software application into separate partitions.

  3. a partition for the pagefile.

  Some people think mistakenly that the pagefile on another
  score will improve performance. It is also false; It doesn t
  help and often I hurt, performance, because it increases the movement of the head
  to get back to the page to another file frequently used
  data on the disk. For best performance, the paging file should normally
  be on the most widely used score of less used physical player. For
  almost everyone with a single physical disk than the same drive s
  Windows is on C:.

  4. a partition for backup for other partitions.

  Some people make a separate partition to store backups of their other
  or partitions. People who rely on a "backup" are a joke
  themselves. It is only very slightly better than no backup at all.
  because it leaves you likely to be simultaneously the original losses
  and backup for many of the most common dangers: the head crashes and other
  types of drive, serious glitches to power failure, near lightning
  strikes, virus attack, even stolen computer.  In my opinion,.
  secure backup must be on a media removable and not stored in the
  computer.

  5. a partition for data files

  Above, when I discussed separate Windows on a clean partition,
  I pointed out that separate data from Windows is a false comfort if
  He of done with the idea that data will be safe if Windows ever
  must be reinstalled. I call it a false comfort that's because
  I'm afraid many people will rely on this separation, think that their
  data are safe there and so do not take measures to
  Back it up. In truth the data is not safe there. Having to reinstall
  Windows is just one of the dangers to someone a s hard disk and not
  probably even one. This kind of "backup" falls into the same
  category, as a backup to other partitions partition; It lets you
  sensitive to the simultaneous loss of the original and the backup on many of
  the most common dangers that affect the entire physical disk, not
  just the particular partition. Security comes from a solid backup
  diet, not how partition you.

  However, for some people, it may be a good idea to separate Windows and
  programs on the one hand of the data on the other, putting each of the
  two types into separate partitions. I think that most people
  partitioning scheme must be based on their backup system and backup
  plans are generally of two types: whole hard disk imaging
  or data only backup. If you back up data, backup is
  usually facilitated by the presence of a separate with data only partition;
  to save just the score easily, without having to
  collect pieces from here and elsewhere. However, for
  those who backup by creating an image of the entire disk, there is
  usually little, if any, benefit the separation of data in a partition of
  its own.

  Furthermore, in all honesty, I must point out that there are many
  very respected people who recommend a separate partition for Windows,
  Whatever your backup plan.  Their arguments haven t convinced
  me, but there are clearly two views different here.

  6. a partition to image files

  Some people like to deal with the images and videos as something separate
  other data files and create a separate partition for them. To my
  the spirit, an image is simply another type of data and there is no
  the advantage in doing so.

  7. a partition for music files.

  The comments above related to the image files also apply to music
  files. They are just another type of data and must be dealt with the
  just like the other data.

  8. a partition for a second operating system to dual-boot to.

  For those who manage several operating systems (Windows Vista, Windows
  XP, Windows 98, Linux, etc.), a separate partition for each operating
  system is essential. The problems here are beyond the scope of this
  discussion, but simply to note that I have no objection to s
  all these partitions

  Performance

  Some people have several partitions because they believe that it
  somehow improves performance. That s not correct. The effect is
  probably low on modern computers with modern hard disks, but if
  whatever it is, the opposite is true: more music mean poorer
  performance. That's because normally no partition is full and it
  so are gaps between them. It takes time for the drive s
  read/write heads to cross these gaps. Close all files
  are, faster access to them will be.

  Organization

  I think a lot of people overpartition because they use scores as a
  organizational structure. They have a keen sense of order and you want to
  to separate the apples from the oranges on their readers.

  Yes, separating the different types of files on partitions is a
  technical organization, but then is to separate different types of
  files in folders. The difference is that the walls are static and
  fixed in size, while the files are dynamic, changing size automatically
  as needed to meet your changing needs. This usually done records
  a much better way to organize, in my opinion.

  Certainly, partitions can be resized when necessary, but except with the latter
  versions of Windows, which requires a third-party software (the and the
  possibility to do so in Windows is primitive compared to the third-party
  solutions). These third party software normally costs money and not
  any point and how stable it is, affects the entire disk.
  with the risk of losing everything. Plan your partitions in
  first place and repartitioning, none will be necessary.  The need
  to repartition usually occurs as a result of overpartitioning in
  the first place.

  What often happens when people organize with partitions instead
  records are that they make a miscalculation of how much room they need on each
  This partition, and then when they run out of space on the partition
  When a file is logically, while having plenty of space
  on the other hand, they simply saving the file in the score of "poor".
  Paradoxically, therefore, results in this kind of score structure
  less organization rather than more.

  So how should I partition my drive

  If you read what came before, my findings will not come as a
  surprise:

  1. If your backup set is the image of the entire disk, have just one
  single (usually c partition :));

  2. If you backups just data, have two partitions one for Windows and
  application programs installed (usually c :)), the other for data
  (normally D :).)

  With the exception of multiple operating systems, it is rarely
  any advantage to have more than two partitions.