Two Adobe ID compete with each other.

Similar Questions

• Issue of school laboratory: setting IPs & VMnet1 so two computers can communicate with each other and to access the internet

  Hello ~

  This question has probably asked a million times in a way or another, but here's my specific: I'm a laboratory for school. I've set up two virtual servers (Windows Server 2012) in VMware Pro 12. The goal is to speak (see others). According to the instructions of the teacher, I set them up as follows:
  
  "Assign your appropriate servers of IP addresses based on your installation environment.  For example, if your network environment uses the class C address range 192.168.1.x, assign a server IP 192.168.1.10, 255.255.255.0 subnet mask, a default gateway 192.168.1.1 and the other server IP 192.168.1.11, 255.255.255.0 subnet mask, a default gateway 192.168.1.1.  Note: If these IP addresses will conflict with your internal network (provide your virtual machines with access to the internet), please choose a different set of address that will work for you. »

  
  

  I need to know what will work addresses. got a domain controller DC1.  Now, I can't see each other. I can't connect to Internet via IE which is one of the 'evidence' that I'm supposed to provide.

  
  

  When I go to the Publisher, I see as the guest only parameter (how is it said to set up when you first install the VMs) is 198.162.150.0. I did not who, but I'm a little but I don't want to make things worse by changing things. I guess that's where the problem is, but I'm not sure what to put the IP, default subset mask and DNS for so I'm stuck.
  
  If it means anything, it is in fact on a borrowed laptop which is connected to the WiFi and wireless. The laptop has internet but I don't know how exactly bringing on the virtual machine when it come to be able to connect. I don't need to become an admin system; This is a compulsory course and I'm just trying to understand enough about it to pass. The problem is that other labs are constructed on it so I can't just ignore it.
  
  Any advice you can offer would be GREATLY appreciated. By the way, happy new year to you all.
  

  Sorry, yes it was a typo. It's supposed to be 192.168.150.xxx.

  Although the virtual machine must be able to communicate if they are both configured similarly (i.e. host only in this case), you generally EF IP addresses in the subnet host only for those virtual machines to be able to access it from the host, which - as mentioned earlier - should have an address of VMnet1 IP of 192.168.150.1.

  André

• HELP: What router supports VLAN? -I wish both groups cannot communicate with each other.

  Hi all

  I have 5 wireless devices must connect to the router.

  I want to divide it into 2 groups:

  That is to say, 1, device A, B, C, group 2, device D, E.

  I would like two groups cannot communicate with each other.

  I've heard, it can be done by VLAN, is e2500 can adapt to what I need?

  What about EA3500 and EA4500?

  I use G wireless, is what it means that ea4500 is out of choice even if it supports VLAN?

  Thank you all!

  Evil

  Thanks for the clarification for the OP

  FWIW

  is this an alternative to routers that do not support of VLAN, to do what you want

  http://www.SmallNetBuilder.com/lanwan/lanwan-HOWTO/32486-how-to-segment-a-small-LAN-using-tagged-VLA...

• Two Xbox 360 Wireless controllers Microsoft will interfere with each other?

  * Original title: Microsoft Xbox 360 for Windows wireless controllers... Two will interfere with each other?

  Controller: Microsoft Xbox 360 Wireless Controller for Windows (JR9-00011)

  Operating systems: Windows 7

  I have two PCs located in the same room. Is it possible to set up a wireless for each of them so that they do not interfere with each other?

  Hello

  I would like the links and see if it helps.

  How to set up your Xbox 360 to your Windows PC controller

  Set up your Xbox 360 for Windows gamepad

  If you have other questions, please post your request in the Xbox forums for assistance on this issue.

  http://forums.Xbox.com/

  Hope this information helps.

• List boxes drop-down interfearing with each other

  HE SOLVED. / Tobias
  
  
  Hello
  When I use two combo boxes with the code adobe (from Component Explorer Flex) example they interfere with each other. When I make a choice in a box the choice I made in the other disappears from the box. How can I change the code to avoid that / or do I have to use a different configuration with the code?
  
  Can someone please explain how to reach Code correctly (can't find no & amp; quot; a button insert code & amp; quot; or similar)
  
  Se my example:
  
  & amp; amp; Lt;? XML version = & amp; amp; quot; 1.0 & amp; amp; quot; Encoding = & amp; amp; quot; UTF - 8 & amp; amp; quot;? & amp; amp; GT;
  & amp; amp; Lt; xmlns:mx = MX:application & amp; amp; quot; http://www.Adobe.com/2006/MXML & amp; amp; quot; page = & amp; amp; quot; absolute & amp; amp; quot; & amp; amp; GT;
  & amp; amp; Lt; MX:script & amp; amp; GT;
  & amp; amp; Lt;! [CDATA]
  [Bindable]
  public var vinalternativ: Array = [{label: & amp; amp; quot; 1 glas husets & amp; amp; quot; wine: 65}, {label: & amp; amp; quot; 2 glas husets & amp; amp; quot; wine: 130}, {label: & amp; amp; quot; dryckespaket 3 ratters & amp; amp; quot; wine: 230}];
  
  [Bindable]
  public var sluttider: Array = [{label: & amp; amp; quot; 24,00 & amp; amp; quot; data: 0}, {label: & amp; amp; quot; 01.00 & amp; amp; quot; data: 1500}, {label: & amp; amp; quot; 02.00 & amp; amp; quot; data: 3000}];
  
  [Bindable]
  public var selectedItem:Object;
  ]] & amp; amp; GT;
  & amp; amp; Lt; / mx:Script & amp; amp; GT;
  
  & amp; amp; Lt;! -first combo - & amp; amp; GT;
  
  & amp; amp; Lt; id = MX:ComboBox & amp; amp; quot; ComboBox2 & amp; amp; quot; x = & amp; amp; quot; 86 & amp; amp; quot; y = & amp; amp; quot; 73 & amp; amp; quot; dataProvider = & amp; amp; quot; {sluttider} & amp; amp; quot; close = & amp; amp; quot; selectedItem = ComboBox (event.target) .selectedItem & amp; amp; quot; width = & amp; amp; quot; 106 & amp; amp; quot; / & amp; amp; GT;
  & amp; amp; Lt; id = MX:textarea & amp; amp; quot; lokalhyra & amp; amp; quot; x = & amp; amp; quot; 289 & amp; amp; quot; y = & amp; amp; quot; 74 & amp; amp; quot; width = & amp; amp; quot; 70 & amp; amp; quot; height = & amp; amp; quot; 22 & amp; amp; quot; text = & amp; amp; quot; {selectedItem.data} & amp; amp; quot; / & amp; amp; GT;
  
  & amp; amp; Lt;! --deuxieme combo - & amp; amp; GT;
  
  & amp; amp; Lt; id = MX:ComboBox & amp; amp; quot; vinCombo & amp; amp; quot; dataProvider = & amp; amp; quot; {vinalternativ} & amp; amp; quot; close = & amp; amp; quot; selectedItem = ComboBox (event.target) .selectedItem & amp; amp; quot; x = & amp; amp; quot; 86 & amp; amp; quot; y = & amp; amp; quot; 139 & amp; amp; quot; width = & amp; amp; quot; 106 & amp; amp; quot; / & amp; amp; GT;
  & amp; amp; Lt; id = MX:textarea & amp; amp; quot; vinval & amp; amp; quot; x = & amp; amp; quot; 289 & amp; amp; quot; y = & amp; amp; quot; 140 & amp; amp; quot; width = & amp; amp; quot; 70 & amp; amp; quot; height = & amp; amp; quot; 22 & amp; amp; quot; text = & amp; amp; quot; {selectedItem.wine} & amp; amp; quot; / & amp; amp; GT;
  & amp; amp; Lt; / mx:Application & amp; amp; GT;
  

  HE SOLVED. / Tobias

  Hello
  When I use two combo boxes with the code adobe (from Component Explorer Flex) example they interfere with each other. When I make a choice in a box the choice I made in the other disappears from the box. How can I change the code to avoid that / or do I have to use a different configuration with the code?

  Can someone please explain how to reach Code correctly (can't find no & quot; Insert button code & quot; or similar)

  Se my example:

  & amp; Lt;? XML version = & amp; quot; 1.0 & amp; quot; Encoding = & amp; quot; UTF - 8 & amp; quot;? & amp; GT;
  & amp; Lt; xmlns:mx = MX:application & amp; quot; http://www.Adobe.com/2006/MXML & amp; quot; page = & amp; quot; absolute & amp; quot; & amp; GT;
  & amp; Lt; MX:script & amp; GT;
  & amp; Lt;! [CDATA]
  [Bindable]
  public var vinalternativ: Array = [{label: & amp; quot; 1 glas husets & amp; quot; wine: 65}, {label: & amp; quot; 2 glas husets & amp; quot; wine: 130}, {label: & amp; quot; dryckespaket 3 ratters & amp; quot; wine: 230}];

  [Bindable]
  public var sluttider: Array = [{label: & amp; quot; 24,00 & amp; quot; data: 0}, {label: & amp; quot; 01.00 & amp; quot; data: 1500}, {label: & amp; quot; 02.00 & amp; quot; data: 3000}];

  [Bindable]
  public var selectedItem:Object;
  ]] & amp; GT;
  & amp; Lt; / mx:Script & amp; GT;

  & amp; Lt;! -first combo - & amp; GT;

  & amp; Lt; id = MX:ComboBox & amp; quot; ComboBox2 & amp; quot; x = & amp; quot; 86 & amp; quot; y = & amp; quot; 73 & amp; quot; dataProvider = & amp; quot; {sluttider} & amp; quot; close = & amp; quot; selectedItem = ComboBox (event.target) .selectedItem & amp; quot; width = & amp; quot; 106 & amp; quot; / & amp; GT;
  & amp; Lt; id = MX:textarea & amp; quot; lokalhyra & amp; quot; x = & amp; quot; 289 & amp; quot; y = & amp; quot; 74 & amp; quot; width = & amp; quot; 70 & amp; quot; height = & amp; quot; 22 & amp; quot; text = & amp; quot; {selectedItem.data} & amp; quot; / & amp; GT;

  & amp; Lt;! --deuxieme combo - & amp; GT;

  & amp; Lt; id = MX:ComboBox & amp; quot; vinCombo & amp; quot; dataProvider = & amp; quot; {vinalternativ} & amp; quot; close = & amp; quot; selectedItem = ComboBox (event.target) .selectedItem & amp; quot; x = & amp; quot; 86 & amp; quot; y = & amp; quot; 139 & amp; quot; width = & amp; quot; 106 & amp; quot; / & amp; GT;
  & amp; Lt; id = MX:textarea & amp; quot; vinval & amp; quot; x = & amp; quot; 289 & amp; quot; y = & amp; quot; 140 & amp; quot; width = & amp; quot; 70 & amp; quot; height = & amp; quot; 22 & amp; quot; text = & amp; quot; {selectedItem.wine} & amp; quot; / & amp; GT;
  & amp; Lt; / mx:Application & amp; GT;

• AnyConnect Clients cannot communicate with each other

  I have a problem that I've been pulling my hair out... my teleworkers connect to our network of Corp. via a connection AnyConnect VPN (version 3.1) to a Cisco ASA5520. I have not split tunneling enabled for this profile, so that all traffic should pass through the tunnel and all guests are in the same subnet L3... as far as their IP VPN address goes. The problem is the teleworker PCs cannot communicate with each other (pings/RDP/etc.). When I look at the newspaper I see traffic from one to another, have denied anything, but they do not communicate. My Network Corp., I can communicate with the two PCs Anyconnect very well. When I go to monitoring. ASDM itineraries I see each host that is connected to the ASA via Anyconnect, and the gateway for each is the default gateway of the SAA.

  Am I missing some setting in the VPN profile that prevents the access between these hosts? I think that something come in the newspaper...

  Have you enabled crossed and also a free NAT between AnyConnect users?

  permit same-security-traffic intra-interface

  network of the AnyConnect_users object

  subnet

  public static AnyConnect_users AnyConnect_users destination NAT (outside, outside) static source AnyConnect_users AnyConnect_users

  If this does not resolve your problem, please post a sanitized complete configuration of your ASA.

• Microsoft 3000 wireless keyboards; they will interact with each other

  I have 2 PC and I would like to replace the wired keyboards for 2 sets of Microsoft 3000 keyboard, will they interact with each other and can I change Ch / Freq of the units

  Hi Baz,

  Each keyboard has different frequency and will not interact with each other.

• I have Firefox and Internet Explore installed on my laptop, the question is, will they conflict with each other and should I get rid of one or the other?

  Hi, I have the browser explorer Firefox and Internet on my laptop, a friend told me that they will be in conflict with each other. the question is what I would do abouth this.

  Your friend has any idea. Both work very well.

• ASA - Tunnel all traffic, allow rays to communicate with each other

  Well, I hope someone can help me with this headache! Switching to employ a PIX and VPN 3005 concentrator Office at home in an ASA5510 for firewall and IPSEC tunnels. It is pretty much a

  • VPN on a stick, multiple rays.
  • All traffic sent by tunnel
  • Internet access through main office (using the web filter) of
  • VOIP to VOIP between rays
  • All departments are using the clients VPN 3005 HW or ASA 5505 s

  HEADQUARTERS: 10.0.0.0/24

  Speaks 1: 192.168.11.0 / 24

  Speaks 2: 192.168.12.0 / 24

  Speaks 3: 192.168.13.0 / 24

  -continues to 192.168.31.0 / 24

  Spoke with the current configuration, 1 can communicate with all the resources in the home, office and Internet integrated properly checked by a tracert. However, the rays cannot communicate with each other. This is required for VOIP traffic, when all TALK TALK calls are made (sites).

  Logging information when talk of talks initiated icmp:

  • No group of translation found for icmp src, dst outside: 192.168.31.1 inside: 192.168.11.1 (type 8, code 0)

  If I remove the nat (outside) 1 192.168.0.0 255.255.00 - rays will begin to respond to each other, but then the rays cannot tunnel through the Home Office Internet traffic. My brain is so scrambled after the cramming of VPN configurations for these days, so I hope someone has an idea. I've always used concentrators 3005, so it's a little different! In the search for documentation for this configuration, I was surprised that this isn't a most common topology. It seems that this article would (http://www.cisco.com/en/US/products/ps6120/products_configuration_example09186a00805734ae.shtml), but there is no rays! In any case, I'm sure this has something to do with NAT rules and perhaps who need access for traffic list speaks of talking.

  =============================================

  ASA Version 8.2 (1)
  !
  hostname asa5510

  interface Ethernet0/0
  Speed 100
  full duplex
  nameif outside
  security-level 0
  IP address 97.65.x.x 255.255.255.224

  interface Ethernet0/1
  Speed 100
  full duplex
  nameif inside
  security-level 100
  IP 10.0.0.40 255.255.0.0

  permit same-security-traffic inter-interface

  permit same-security-traffic intra-interface

  the DM_INLINE_NETWORK_1 object-group network
  object-network 10.0.0.0 255.255.0.0

  object-network 192.168.0.0 255.255.0.0

  access-list sheep extended ip 10.0.0.0 allow 255.255.0.0 192.168.0.0 255.255.0.0

  Allow Access-list extended wccp servers ip host 10.0.0.83 a

  Redirect traffic extended access-list deny ip any object-group DM_INLINE_NETWORK_1

  Redirect traffic scope permitted any one ip access-list

  Global 1 interface (outside)
  NAT (outside) 1 192.168.0.0 255.255.0.0
  NAT (inside) 0 access-list sheep
  NAT (inside) 1 10.0.0.0 255.255.0.0

  Route outside 0.0.0.0 0.0.0.0 97.65.x.x 1
  Route inside 192.168.0.0 255.255.255.0 10.0.0.1 1
  Route inside 192.168.2.0 255.255.255.0 10.0.0.1 1
  Route inside 192.168.3.0 255.255.255.0 10.0.0.1 1

  Crypto ipsec transform-set esp-3des esp-md5-hmac RIGHT
  life crypto ipsec security association seconds 28800
  Crypto ipsec kilobytes of life - safety 4608000 association
  Crypto ipsec df - bit clear-df outdoors

  Crypto-map dynamic dynmap 1 transform-set RIGHT

  map mymap 65535-isakmp ipsec crypto dynamic dynmap

  mymap outside crypto map interface

  crypto isakmp identity address

  crypto ISAKMP allow outside

  crypto ISAKMP policy 5
  preshared authentication
  3des encryption
  sha hash
  Group 2
  life 86400

  crypto ISAKMP policy 10
  preshared authentication
  3des encryption
  md5 hash
  Group 2
  life 86400

  crypto ISAKMP ipsec-over-tcp port 10000

  management-access inside

  a basic threat threat detection

  no statistical access list - a threat detection
  no statistical threat detection tcp-interception

  WCCP web cache redirect-list Redirect-traffic group-list password xxxxxxx wccp-servers
  WCCP 90 redirect-list traffic Redirect wccp servers group-list password xxxxxxx

  WebVPN

  internal MJHIvpn group strategy

  attributes of Group Policy MJHIvpn
  value of server WINS 10.0.10.1 10.0.10.2
  value of 10.0.10.1 DNS server 10.0.10.2
  allow password-storage
  Split-tunnel-policy tunnelall
  mjhi.local value by default-field
  allow to NEM

  username field-3002 SjfS1Pq2xZGxHicx encrypted password

  attributes of username field-3002
  VPN-access-hour no
  VPN - 250 simultaneous connections
  VPN-idle-timeout no
  VPN-session-timeout no
  Protocol-tunnel-VPN IPSec
  allow password-storage
  type of remote access service

  remote access to field tunnel-group type

  General-field tunnel-group attributes
  Group Policy - by default-MJHIvpn

  IPSec-attributes of tunnel-group field
  pre-shared-key *.

  class-map inspection_default
  match default-inspection-traffic
  !
  !
  type of policy-card inspect dns preset_dns_map
  parameters
  message-length maximum 512
  Policy-map global_policy
  class inspection_default
  inspect the preset_dns_map dns
  inspect the ftp
  inspect h323 h225
  inspect the h323 ras
  inspect the rsh
  inspect the rtsp
  inspect sqlnet
  inspect the skinny
  inspect sunrpc
  inspect xdmcp
  inspect the sip
  inspect the netbios
  inspect the tftp
  inspect the they
  inspect the icmp
  !
  global service-policy global_policy

  Hello Ala,

  In Act got to be with the Nat configuration.

  So basically you want to tunnel the traffic on the rays to communicate with each other.

  OK, it would be with a nat 0 with the access list with the corresponding traffic outside.

  Also on the crypto ACL for each site configuration, you must add an entry for the traffic of other offices.

  I hope that I have explained myself.

  Have a good

  Julio

  Note all useful posts!

• Is there a way or a widget in Muse, allowing the objects and images to react with each other?

  Hello. I would make both objects or images imported into Muse react with each other. When I say react, think of a ball bouncing off a wall or a pool ball hitting a bunch of other billiard balls. I searched for a widget that might allow cela and couldn't find one. Is this something that can do Muse, or should I look for something else... edge or the interaction of coding? Thank you.

  You can do using the edge, then publish it in the "animated dashboard deployment package", ".oam".

• How can I display two PDF files next to each other?

  How can I display two PDF files next to each other?  In the older version of Acrobat Reader, I was able to open each PDF in a separate window and used all the time.

  Hi julians7844423,

  Open Acrobat Reader DC, navigate to the Edit-> Preferences-> General-> uncheck "Open Documents in the new tab in the same window.

  Restart your system & now try to open PDF files.

  Let me know if it solves your problem.

  Kind regards
  Nicos

• Can I create a page Web of Muse that it is child Pages could be open on different computers and communicate with each other?

  
  I want to create a Web site with 4 child pages that interact with each other when opened separately on 4 different computers.

  Is this possible?

  Example:

  Child 3-page Web site open on 3 different computers with triggers and the following objectives:

  PC #1 - child #1 - confirm button (trigger)

  PC #2 - Page #2 - accepted Confirmation Popup, resulting by clicking on 'confirm' page computer/child #1 (target)

  PC #3 - child Page #3 - calendar Popup changed, resulting by clicking on 'confirm' page computer/child #1 (target)

  Any ideas are much appreciated.

  THX.

  No this is not possible with Muse.

• How to install VMplayer 3 network for virtual machines to comminicate with each other?

  People,

  Hello. I use VMPlayer 3.

  SE host: Windows 7
  Comments to: Windows XP and Oracle Linux 5

  I need to set up the network and activate Windows XP communicate with Oracle Linux 5.

  I followed this tutorial http://www.vmware.com/support/ws5/doc/ws_devices_serial_2vms.html to configure 2 virtual machines in Windows 7 host machine.

  I tried to test 2 virtual machines in the way as below:

  In Linux, [user@localhost ~] $ping WindowsXP_HostName
  Release: Unknown host WindowsXP_HostName

  
  At the Windows XP command prompt:
  C:\ping localhost.localdomain
  Its release: ping localhost 127.0.0.1 with 32 bytes of data...
  Reply from 127.0.0.1: bytes = 32 time = 2ms TTL = 128

  
  He meets a few times and then disconnected by itself. It seems that Windows XP is ping itself and not Linux server. The host name of the Linux server is 'localhost' as well. It is a kind of confusion for me.

  
  From the information above, we can see that 2 VMs cannot connect between them.

  Can any folk provides a tutorial or example or case study to set VMPlayer 3 allowing 2 virtual machines communicate with each other by step?

  Very grateful in advance.

  In the guest machine, all I see is click on VMplayer-> VM-> settings-> network-> Network adapter Connection-> select Bridged: directly connected to the physical network. After that, nothing to keep.

  That's it for the network card in Virtual Machine of its parameters, and the rest is done to each guest at the guest OS level.

  In Windows 7 host machine, I don't see anything first.

  What we need to do is to assign 3 IP addresses to 3 machines: Win 7, Win XP Guest and Linux host.

  Why the world can't bring you up Google in a browser and type, the ip static windows xp, then static ip rhea of windows 7 and finally static ip.  As I have already said there are more then enough tutorials on the Internet about how to configure a static IP address by a given operating system then I suggest you Google it!  It makes absolutely no sense to write the instructions step by step for you when there are already dozens of tutorials available on the internet.

• Two virtual machines to communicate with each other - intent an SMS Lab for test deployment?

  Hi friends ,.

  I am a new user and would like your help pretty desperately. The scenario is that I want to implement a SMS Lab to deploy the application from the server to a client and test the application. I have all the necessary knowledge to the packaging of application is concerned, and would like to help as much as VMWare is concerned.

  I created two virtual machines and one of them will be configured as a server and the other will be the client. I created a team with these two machines in it. I am trying to ping from one machine to the other and its does not work. I only use the method of configuration host. The idea is simply to make the two systems communicate so that I can finish the entire configuration and use the same SMS deployment lab.

  -First of all, I'm new to all this so I would like to know whther to everything I do is correct and what is the largest possible?

  -What I have to do something else to make sure that those two communicate about someother or any other configuration software is necessary?

  I would like to ask you guys to be a little more specific are you when you help others that I need you guys ore than a person who is used to working on VMWare.

  And just so you know if it helps, I use VMWare Workstation 6.0.

  What you are doing is reasonable.  Both of your virtual machines have an IP address on the same subnet?  In general, the scenarios no-ping, the first thing to check is the firewall in the guest computers.  Have you checked that allows ping traffic?  If it is disabled?

  -KjB

  VMware vExpert

• two items exactly close to each other

  Hello

  I have two points, point A and point B. I want that they in one line to close between them, no space.

  I tried css, but have still some problems.

  googled and got links to the presentation of the grid, but still they are online, but not more close to each other.

  Thank you

  Hi 2939203,

  It's like three times I asked someone to chnge their full name, please follow this link to start and also read it once.

  Now,.

  You must define the layout of the grid.

  2939203 wrote:

  Hello

  I have two points, point A and point B. I want that they in one line to close between them, no space.

  I tried css, but have still some problems.

  googled and got links to the presentation of the grid, but still they are online, but not more close to each other.

  Thank you

  Point has:

  The new grid: No/Yes

  Start the new row: Yes

  Now the point b:

  Start the new grid: No.

  Start the new row: No.

  New section: No. *.

  Thank you

  Zapp