U3415W - 50/50 for the double transaction?

Similar Questions

• I have put in place for the double sided copies on Canon Pixma MX 922? Thank you

  Hello

  How can I get my Canon MX 922 to make double sided copies?  Thank you

  Wish they offered an instruction manual...

  Chrismiss56

  Hi chrismiss56,

  To copy both sides of the page, please select your PIXMA MX922 and follow these steps:

  1. press the button COPY.

  2. load the paper you want to print on in your PIXMA MX922.

  3. load the original document on the glass exhibition or in the ADF.

  4. press on the right-hand (under Print on the LCD settings) button.

  5. press up or down arrow select-sidedPrintSetting 2 ot.

  6. press on the arrow right or left to select 2 sides.

  7. press the button color for color copying, or the black button in black & white copy.

  Will depend on where you have placed the original, additional screens will be displayed.  Follow the prompts to complete the copy.

• What is the best practice for the double management interfaces?

  Hello community!

  I'm upgrading to a few host ESX to ESXi 4.1U1 4.0 in the coming weeks. My question is about how to configure the management networks. Obviously in ESX 4.0 Classic I have a Service Console port (on vSwitch0) group and a group of ports VMkernel (also on vSwitch0) which provides my host with SC and vmotion capabilities, as we all know. Note: my vSwitch0 has two vmnic attached to it, is pending and is active. That's just how we have our double installation of switches, so it must be active / standby.

  I got to thinking (book the great from HA and DRS deepdive Duncap Epping and Frank Denneman), that I should consider carefully when my network mangement I improve these hosts to ESXi 4.1 - which of course done away with the Service Console and use the vmkernel instead.

  The question is, in which best practices and account with my setup: I have two vmkernel ports? If so, how should I configure each for traffic management and vmotion vmkernel?

  I think it will be a good discussion to have.

  Thank you all,

  Matt

  The NIC vSwitch0 value active/active, the vswif (and future vmkernel management) team of NIC Active vmnic6 and vmnic1 ensures and leaves the vMotion vmkernel NIC team as is.

  This will allow you to use two physical network interface cards at the same time while having a failover plan and keep your physically separate management and vMotion traffic.

  In the end:

  vSwitch: vmnic1 vmnic6 active, active.

  VMK (Mgt): active eve of vmnic1 vmnic6.

  VMK (vMotion): active standby, vmnic6 vmnic1.

• Transform click twice on Z for the double click on the mouse

  When I click 2 times on the 'z' (90 keycode) key on my keyboard, my item is deleted.

  I would change it and when you click 2 times with the mouse, the item is deleted, but I can't figure out how to do it... If mouseDown = true? It does'nt seems not to work...

  timer=new Timer(500, 1); 
  stageRef.addEventListener(KeyboardEvent.KEY_UP, removeDraggedItem);  
  private function removeDraggedItem(e:KeyboardEvent)
  { if(timer.running==true) 
  { if(e.keyCode==90) 
  { stageRef.removeEventListener(MouseEvent.MOUSE_MOVE, dragItem); 
  stageRef.removeEventListener(Event.ENTER_FRAME, itemHitTest); 
  draggedItem.removeEventListener(MouseEvent.MOUSE_DOWN, itemClick);  
  stageRef.removeChild(draggedItem); toolbar.useText.text = "";  
  if (stageRef.contains(this)) stageRef.removeChild(this);  
  Mouse.show(); 
  Engine.playerControl = true; } 
  }  else if(e.keyCode==90) { timer.start(); }
   }
  

  I tried to change (e.keyCode == 90) by (e.buttonDown). No error but nothing happens when I double click... no idea why?

  Use a double click listener.

• Need drivers for camera double digital vivitar

  I want to download free drivers for the double camera vivicam 10.  does anyone know where to get them?

  From Internet Explorer

  Original title: camera double digital Vivitar

  Did you contact the Support of Vivitar again?

  [THX @here]

• Need to change the text in the "Basic Transaction button bar" button

  Hi all
  
  I have an obligation to change the text of the "Preview settings" custom text button in ' * Basic Transaction button Bar * "model. Is there a way we can achieve this? If so, please let me know how I can open it this model.
  
  Thank you
  Vijay

  Vijay-

  You cannot change a seeded content model. You must instead make a copy of it, modify it and use the copy in your user interface.

  In the Configurator developer repository, access the User Templates interface-> content-> button bar models models and make a copy of the Basic Transaction button bar model. (You can leave your copy in the folder models bar button if you like, or create in any other folder of your choice.) Open the new template for editing and change the button Configuration Overview, change its Source of the legend (and perhaps his flipping text Source as well), the new text that you want to appear on the button.

  Once you have changed your new template to your liking, change the node root of the user interface you want to use and utility models of the user interface definition section, choose your new template for the Basic Transaction model.

  I hope this helps!

  Mathgamain

• Pick activity with transaction XA causing the double mistake

  Hi all

  Hi all

  I have a BPEL service that reads the message to a JMS queue and then waits for a response with a PICK 5 min on alarm activity. Now there are rare cases, when I did not receive the answer within 5 minutes (but after > 5 min) and the Pick activity goes into alarm and error. But my JMS queue has an active XA transaction and that translates into a retry of the function of the source. This re-triggers all of the services and another pick activity is created. the choice of the second activity ends sometimes successfully, but sometimes also with the double-error error activity.

  The exact error message is attached here... Note also that we set the correlation id for the intervention on the pick activity...

  concerning

  Rakesh

  Hello

  That's an option... but I try to understand what is causing this intermittent problem to throw the double error message.

  Thank you

  Rakesh JS

• How to ensure that the value of a control (for example double) initializes the last value when the VI has been closed?

  I use a cluster as a control. I would like to double in this control to automoatically values to fill their last values set when the VI is opened or accessed for the first time. It would be great if someone could point out for me. Thanks in advance!

  In my opinion, the configuration files are the easiest method and the best.  Simply save your last values to the file when your code ends.  At the beginning of your code, to read the file and fill in the controls with the values read.  With the configuration files, the section name can be the name of the cluster, and key names can be control names.

  I know OpenG has some pretty nice to do, but I prefer to use the native functions OR when I can.  When porting to a new system, there is no need to copy any additional screws library (OpenG library).  The native DV come with Labview.

• What is the minimum value for the data type double?

  ... a more academic question: what is the minimum value of the data type double? I thought 'double', it is the 8-byte IEEE standard and what I remember, it's + - 1.7E + - 308.  The more different number of 0 should be 1.797E - 308.

  This is why I was a little surprised when I looked at the data output of my calculation of CVI, where I found the numbers with exponents of E-319 or E-324 as the smallest value...

  But I'm sure there's an explanation :-)

  Thank you for sharing with me,

  Wolfgang

  The largest number is indeed the order of + 1.7E + 308; There are a smaller number of - 1.7E + 308. Note that this is in fact the most negative number, which is the smallest by some reckoning. For the small beach of the Exhibitor, things get a little more complicated. 1E-308 can be represented with complete accuracy and resolution, but if you're willing to lose a few bits of precision, you can go down even further. For example:

  Double x, y, z:

  x = 1E-300;

  y = 1E7;

  z = x / y;               Give 1.000000000000000E - 307

  y = 1E8;

  z = x / y;               Give 9.999999999999999E - 309

  y = 1E18;

  z = x / y;               Give 9.999987484955998E - 319

  y = 1E23;

  z = x / y;               Give 9.881312916824931E - 324

  So, as you can see, values less than 1E-308 are possible, but they become increasingly more inaccurate and should not be relied upon.

  JR

• Control of the double loop for a positioning system. - movement ocntrol

  I am currently a control of the double loop for a positioning system, I use the speedometer to read the speed and the encoder for position on the position of the platform.

  the problem I'm meeting now, is that I'm not sure weather the computer have the PID toolkit, because I can't find them under the control design and simulation module.  so I did a PID using the basic features of labview, related information in the attached documents.

  I'm not sure of the part of the dt, the labview has this kind of service as of the timing of simpling?

  do I have to install the labview real_time potion? I'm just using the labview 8.5

  Another issue is that, how I'm going to let the system remember the position instead of back to 0 whenever I restarted the program? If not is there any other way I can control the motor to move the position of the target that is initially set?

  the last question is that is it possible for me to generate a profile about the current and desired position? to set a maximum speed and acceleration.

  I do not have a motion controller, so I have not installed the module version and motion.

  can someone suggest me a way to do it?

  Hey, 14 I never used TDMS files. but maybe this will help. [zip file]

  and if it isn't, I found this (which you can probably read into its equivalent in English)

  http://digital.NI.com/public.nsf/allkb/099731B9B31936B08625745A0076A610

  [don't forget to Congrats]

• Unable to save changes to the sounds. When registered and then double checked, change moved not. This applies specifically to sound for the navigation to start windows Explorer. I'm putting it to zero. »

  Unable to save changes to the sounds. When registered and then double checked, change moved not. This applies specifically to sound for the navigation to start windows Explorer. I'm putting it to zero.

  Unable to save changes to the sounds. When registered and then double checked, change moved not. This applies specifically to sound for the navigation to start windows Explorer. I'm putting it to zero.

  ====================================
  After making your change did you left click... Apply / OK?
  John Inzer - MS - MVP - digital media experience

• Request for Balance/amount of the historical Transaction summary

  Hello

  I'm working on a report in which one quantity/must correspond with a quantity / in transactional historical summary.

  Amount through my query = quantity in transactional historical summary.

  But balance through my query! = Balance in transactional historical summary.

  
  

  Query is-

  SELECT

  item_id, SUM (target_value)

  Of

  (

  SELECT

  item_id moqv.inventory_item_id, SUM (transaction_quantity * item_cost) target_value

  Of

  mtl_onhand_qty_cost_v moqv

  WHERE

  moqv.organization_id =: org_id

  AND moqv.inventory_item_id = NVL(:Item_id,moqv.inventory_item_id)

  GROUP BY

  moqv.inventory_item_id, moqv. Item_Cost

  UNION ALL

  SELECT

  MMT.inventory_item_id item_id,-SUM (transaction_quantity * actual_cost * nvl(currency_conversion_rate,1)) target_value

  Of

  mtl_material_transactions mmt, mtst mtl_txn_source_types

  WHERE

  MMT.organization_id =: org_id

  AND transaction_date > =: user_date + 1

  AND mmt.transaction_source_type_id = mtst.transaction_source_type_id

  AND mmt.inventory_item_id = NVL(:Item_id,mmt.inventory_item_id)

  Mmt.subinventory_code GROUP, mmt.inventory_item_id

  mmt.subinventory_code is not null

  )

  ITEM_ID GROUP;

  Please, someone at - it help me, what changes are required to achieve the desired result.

  Thanks in advance

  Kind regards

  Anurag Sharma

  Select cost * quantity balance

  Of

  (select round(actual_cost,5) cost, inventory_item_id)

  Of

  mtl_material_transactions one

  where

  inventory_item_id =: ITEM_ID

  and TRANSACTION_DATE<>

  and transaction_id = (select max (transaction_id) in the mtl_material_transactions where inventory_item_id = a.inventory_ITEM_ID and TRANSACTION_DATE<=:p_to_date))>

  (select item_id quantity, sum (target_qty) of)

  (SELECT

  target_qty, item_id

  Of

  (

  SELECT

  item_id moqv.inventory_item_id, SUM (transaction_quantity) target_qty

  Of

  mtl_onhand_qty_cost_v moqv

  WHERE

  moqv.organization_id =: orgn_id

  - and SUBINVENTORY_CODE ('PC store', 'STORE of RTV')

  GROUP BY

  moqv.inventory_item_id, moqv. Item_Cost

  UNION ALL

  SELECT

  MMT.inventory_item_id item_id, target_qty SUM (transaction_quantity)

  Of

  mtl_material_transactions mmt, mtst mtl_txn_source_types

  WHERE

  MMT.organization_id =: orgn_id

  AND transaction_date > =: p_to_date + 1

  AND mmt.transaction_source_type_id = mtst.transaction_source_type_id

  - and MTM. SUBINVENTORY_CODE ('PC store', 'STORE of RTV')

  GROUP BY mmt.inventory_item_id

  )

  WHERE item_id =: ITEM_ID

  ) z, msi mtl_system_items

  where msi.inventory_item_id = z.item_id

  and msi.organization_id =: orgn_id

  Group item_id) xyz

  where xyz.item_id = abc.inventory_item_id

  Thanks for the help... I found the solution.

• HP laserjet 1022 does not wait for the user to turn the pages when printing double-sided

  My Hp laserjet 1022 printer working properly for years.

  So far, when he executed more paper he tried a couple of times to get more paper and then stops with a message on the PC it is out of paper.

  Very annoyingly, this has changed recently, now when it is out of paper, he tries a couple of times to get more paper and watch the message on the PC, saying that it is paper and then again, try a couple of times to get more paper and again shows the same message on the PC and him back... This continues to go on and on.

  It's especially annoying when trying to print double-sided. Before he used to stop and ask you to turn the pages to print the other side. Now the previous behavior overrides the break to turn the pages and keeps it will try to get more paper. As now, it does not wait for the user to turn the pages, in general it spoils the impression out by getting another paper that is not what I wanted, he drives me crazy! It's really hard to print anything double face now.

  All solutions?

  Operating system is Windows 7, I just downloaded and installed the latest driver for this printer "2013-01-09, Version: 20120918" and I get the same behavior. In the properties of the printer that I put some State Messages to Off and at least I don't get the full windows message screen poping up every time the printer is trying again to get more paper. I have not found all the other parameters that may affect this behavior.

  Help!

  Hello

  I solved the problem! I found the original CD for the printer. I uninstall the current driver and then install CD and now when the printer is out of paper trying to get paper a couple of times and then stops, as it used to be.

  Thanks for your help.

  Martin

• Stop the realization of revenues for a particular Transaction in AR

  Hello

  I have a scenario where a client pays upfront for a service item / which will provide us in the future every month. Accounting rules (fixed amounts such as 12 months, 15 months) allows us to recognize revenues in several bouts. Lets say any such transaction took place January 1, 2015, with a value of $1200. Since we use the accounting rule of 12 months, this amount will be recognized back asd $100 every month. Then at the end of February, customer wishes not to receive this service from March. That's why we have to stop recognizing the revenue for the 10 months left in the future. (we are in R12.0)

  Ledger entry from 1 to January 1

  Dr. debtor 1200

  Unearned income CR 1200

  Journal entry of 2 in 1 Jan

  Dr. cash 1200

  CR 1200 debtor

  Ledger entry from 3 to 1 January

  Dr. Uneanred revenue 100

  CR 100 recipes

  Input3 accounting will be generated for all 12 months. I need to stop this accounting of March writing leave. How to do this?

  Thank you

  Lakshith

  Hi all

  Thanks for all the inputs. I found the solution. We need to the credit of the transaction that will reverse all the entries created from March to December.

  Must first set up the profile option: AR: use invoice accounting for credit memos.

  Can credit the transaction using the LIFO rule.

  Thanks to all for the replies.

  Kind regards

  Lakshith

• Help understand the Double billing for the same product on the same account

  Recently, I realized that I make double charge on my account from creative cloud for the same exact items charged to the exact same credit card. In addition, I must say that I had two accounts still somehow. It is because I have lost access to the associated e-mail account and do could not connect. When I talked to Adobe at this time there they notify that I have create a new account with a new email, I did. That being said, every month for almost a year I was charged $31,79 and the new account as well. (I admit I'm not very good about checking all my automatic subscriptions online monthly but supposed to Adobe as a company highly and popular, could do things). I called and the first representative I spoke with today understands the problem and transferred to me for a refund, however once transferred, the representative was not only do not understand but rude and gave me a refund for 6 months. As of today, they canceled the account I have not used and me be charged twice a month for but only paid 6 months more than 12 months of double billing. The representative tried to tell me he was doing me a favor because I wasn't in charge of normal early termination fees. It has become so confusing and so I did at that moment that I said I would get more help here in the forums...

  1. I'm trying to understand why in the world they would even charge me a cancellation fee when I was clearly NOT cancellation of an account, just to make a change, which was made according to the way which they charged me and, of course, who they do not now recognize?

  2. How can I reload the same exact account for exactly the same product with activation of the said product as a single computer, and no other user (not to mention that I just used the product)?

  Any help or advice would be appreciated!

  All first of all my apologies for the not so pleasant experience.

  The Adobe ID here in the forum has a CC bought in March 2016 with no cases registered.

  I understand that this is for another subscription CC, could you please me message in private closed, the file number or the number of order which you have been invoiced in duplicate.

  I can probably follow that.

  Concerning

  Stéphane