Unable to connect to my office that is connected to the same homegroup.

Similar Questions

• I am unable to connect to the Linksys WRT54G Router with wired connection to Office XP.

  My two laptops (XP and a Win7) will be connected to the router wireless and wired (ethernet). When it is plugged directly into the DSL modem, the Office connects and works very well. This problem started when I had to replace the DSL modem.

  I inherited this problem for my elderly mother... and it all started because they gave me the router password wrong, who now works (router has been reset) on two laptops, but when connected, the Office doesn't even show a light of connection on the router except during startup. I no longer get a window of logon passwork for the router, and I am unable to connect/ping the router in the office. (192.168.1.1)

  I would like to clarify a few things.

  1. two laptops work fine with cable connections and wireless through the WRT54G.

  2 desktop PC, which has only a wired connection, does not connect successfully.

  3. the symptoms of the failure of the desktop connection to are that the link on the router at the start light flashes during initialization of the PC but then will Dim.

  4. when the desktop PC trying to connect to the internet, it fails.

  5 when the desktop PC try to connect to the administration WRT54g page it fails.

  6. when the desktop computer try PIING the router at 192.168.1.1 IP address it fails.

  These points are correct?

  Assuming this is correct, open a command prompt and type

  IPCONFIG/ALL

  The output of the command should provide some information about the current state of the network connection.

  It would be useful that you posted this here release.

  The absence of a link light can be your main symptom and may be due to several reasons. He probably has an associate status "media disconnected" in IPCONFIG for the network connection.

  This could be caused by a bad network cable or a network connection disabled in the properties of the network on the PC. Small jets knowing the ot IPCONFIG output is would help more.

  Post this info if you can.

  Good luck

• I could not update or install applications for weeks, so I disconnected my Apple ID and rebooted the phone but now I can't reconnect! The error is: unable to connect to the iTunes Store. I should w8 for ios10 and hope that it will be fixed by the new ios?

  I could not update or install applications for weeks, so I disconnected my Apple ID and rebooted the phone but now I can't reconnect! The error is: unable to connect to the iTunes Store. I should w8 for ios10 and hope that it will be fixed by the new ios? Cause don't want to reset my phone.

  You have tried: If you can not connect to the iTunes Store - Apple Support ?

  And I tried to do a soft-reset/reboot the phone?

• I am unable to connect to the virtual pc Xp mode when I try to open a session given an error unable to connect to the domain that a domain controller is down or unavailable,

  I am unable to connect to the virtual pc Xp mode when I try to open a session given an error unable to connect to the domain that a domain controller is down or unavailable,

  Hi Rajendra Patil,

  I suggest you to ask your question on the TechNet Forums.

  Windows Virtual PC and XP Mode.

  http://social.technet.Microsoft.com/forums/en/w7itprovirt/threads

  I hope this helps!

• CC so that he was trying to install updates is unable to connect to the server.  What should I do?

  CC so that he was trying to install updates is unable to connect to the server.  What should I do?   This is what it looks like.

  Check your hosts file.

  help for that and other adobe.com sure common connection problems read, http://helpx.adobe.com/x-productkb/policy-pricing/activation-network-issues.html

• I have Adobe Reader DC, but have just started to give a message that Adobe is unable to connect to the DDE server, what can I do?

  I have Adobe Reader DC, but have just started to give a message that Adobe is unable to connect to the DDE server, what can I do?

  Hi johnf49911817,

  * Try the solutions below: -.

  Solution 1) (this error occurs when you have more than 1 process of Acrobat running)

  (1) go to the task by pressing Ctrl + Alt + Del Manager

  (2) go to the process in the Task Manager

  (3) terminate all processes associated with Acrobat

  (4) start Acrobat again.

  Solution 2) open Acrobat access to menu help & repair installation.

  Solution 3) control the association of file on your system.

  Solution 4) course for HKEY_CLASSES_ROOT\acrobat\shell\open\ddeexec\application and replace the key 'AcroviewA11' 'AcroviewR11.

  Kind regards

  Christian

• I can't import my script (film) into Adobe Story. The error message says that I am unable to connect to the Adobe servers. Is this a problem with the Adobe?

  I can't import my script (film) into Adobe Story. The error message says: I am unable to connect to the Adobe servers. Is this a problem with the Adobe?

  Yes and no it seems that if the file is a .doc or .pdf, that it does not load properly. But if I bring him in a Final Draft format, it works perfectly.

  Adam

  Sent from my iPhone

• I get a pop up message the first time I open Photoshop CC for the day, "we sorry that we are unable to connect to the server from adobe at the moment..." I followed instructions to turn off my antivirus and firewall, then open it. But the problem still re

  I get a pop up message the first time I open Photoshop CC for the day, "we sorry that we are unable to connect to the server from adobe at the moment..." I followed instructions to turn off my antivirus and firewall, then open it. But the problem still remains. What can we do?

  Moved to this discussion in the creative forum cloud download & install.

  R.O.B. Please see Sign in, activation or connection errors. CC, CS6, CS5.5 - http://helpx.adobe.com/x-productkb/policy-pricing/activation-network-issues.html for more information on how to resolve the error of connection between the computer and our activation server.

• A solution to the "unable to connect to the NFS server" that I can't understand

  (This question is related to the interaction between ESXi and FreeNAS and talk a lot here, but the solution was finally on FreeNAS configuration change, so I hope it's ok that I post in this forum.  It relates to the use of FreeNAS of ESXi).

  I have a FreeNAS system set up specifically for the copy of the virtual machines of my ESXi server as a backup mechanism.  I tried to mount a NFS of FreeNAS disk and ran in a (what appears to be, from discussions on the forum, a common place) problem.  ESXi, during an attempt fix the part gave me the "unable to connect to the NFS server" message.  The search in the log files, I could see some more detail, but nothing that pointed to a solution.  I also searched the logs on the FreeNAS system, nothing helps.

  I was using the IP address of the FreeNAS (static address) system instead of the DNS name when you are trying to reach the storage.

  After hours of trying different methods, creation of username on FreeNAS trying up to ESXi, scouring through all the various points of ESXi config, etc. I am getting nowhere.  Then I came across a post somewhere (not here on the forums, but in a blog somewhere) that said add the ESXi server to the hosts on the FreeNAS system file.

  Once we added - bingo-test.  ESXi logged in straight away and I am running.

  Now, I am trying to determine why the addition of ESXi machine to the FreeNAS hosts file would allow ESXi to connect.  Anyone have any ideas?  The IP address of the ESXi system was already in the allowable range set up in the UI on FreeNAS.

  Thanks in advance.

  Mounting NFS export list process requires the resolution of the customer's name. When a customer initiates the request for an NFS share, server checks its list of export for the requested directory and the name of the customer in this access list for this particular action. Now if the server fails to resolve the name of the initiator denies his request for the mounting of this share. In order to overcome this problem, you must have a dns server in the network, or do you have enter you the names and information of IP address to the server hosts file

  Naeem Holy

• Reinstalled XP and now unable to connect to the internet, dsl provider says the leaves to reinstall the connection LAN how fix this?

  Original title: windows xp.

  reinstalled xp and now unable to connect to the internet, dsl provider says the leaves to reinstall the connection LAN how fix this?

  Hello

  Go to the website of your computer manufacturer > drivers download Section > put your computer model number > operating system > Search adapter network, pilots etc. for her.

  Get graphics, sound while you're there.

  You should always do a reinstallation.

  Use the computer that you use to make the foregoing > download and save in this office > copy of Flash Drive > then install in another computer.

  See you soon.

• HP Deskjet 3510: HP Deskjet 3510 - unable to connect to the printer

  I had this printer for some time but have never been able to properly print to this printer using this specific computer.   FYI, I'm trying to print wireless at it. This office has wireless compatibility.  I have the drivers and all (I think, I HP everything at the time but not the disk that came with it I lost only).  Don't know why it fails, he said only: "unable to connect to the printer.

  Thanks in advance for any help.

  Hi aunt Shirley.

  First of all, we're going to connect the printer to the network:

  -Restore default values of network within the menu on the front panel of the printer wireless.
  -From your computer, connect wirelessly to the network printer (it should be a name similar to HP - Setup - xx - Deskjet 3510).
  -After successfully connecting to the printer, open a web browser such as Internet Explorer or Chrome and type 192.168.223.1 in the address bar and press ENTER.
  -Click on the Wireless Setup Wizard
  -Select your router and enter the password to connect to the printer to the router.

  Run again the printer software to your computer to rediscover the printer on the network.

  See the support institution by clicking on the thumbs upwards in the post that solved your problem. Doing so will help the other members of the forum their solutions also.

• Unable to connect to the VPN

  I can not connect from home (Windows 7 Starter Edition) at the office of the wife (WinXP Home) via a VPN connection.

  Follow-up of the installation a new connection wizard. Unable to connect with the new account (done in the vpn Wizard. Unable to connect with an existing account on the server VPN system either. I am able to connect from another system of home to the system that hosts the server VPN using pcAnywhere.

  Or the other attempt gives an error 800 - VPN tunnel failed.

  Any ideas on where to start looking?

  I can not connect from home (Windows 7 Starter Edition) at the office of the wife (WinXP Home) via a VPN connection.

  Follow-up of the installation a new connection wizard. Unable to connect with the new account (done in the vpn Wizard. Unable to connect with an existing account on the server VPN system either. I am able to connect from another system of home to the system that hosts the server VPN using pcAnywhere.

  Or the other attempt gives an error 800 - VPN tunnel failed.

  Any ideas on where to start looking?

  See this section of the RRAS team blog...

  http://blogs.technet.com/rrasblog/archive/2009/08/12/troubleshooting-common-VPN-related-errors.aspx

  More than likely the XP box is behind a firewall/router which does not pass traffic GRE protocol 47 . You can test the VPN PPTP link by running the test detailed in the traffic VPN PPTP Ping and secitons on this page.

  http://TechNet.Microsoft.com/en-us/library/bb877965.aspx

  GRAP the pptpsrv.exe and pptpclnt.exe programs on the internet or from a CD of XP SP2. If the tests fail work arounds include...

  * Update the firmware on the router to a version known to pass traffic GRE protocol 47.

  * Flashing the router, if supported, with third-party firmware like DD - WRT that supports passing traffic GRE protocol 47.

  * Buying a router known to pass the GRE protocol traffic.

  * Use an alternative such as Secure Shell [SSH] and a free SFTP client such as WinSCP or TBM for secure remote access to files and folders or Remote Desktop/access control to computers on office's LAN.
  MS - MVP Windows Desktop Experience, "when everything has failed, read the operating instructions.

• Unable to connect to the internet after the removal of important processes in the task bar

  I am not very tech-savvy then let me explain.

  I have a laptop Lenovo I recently bought in August 2014.  A friend suggested that I have download the free application "Open Office" in line, so I could open a school power point.  Open Office gave me a handful of viruses, which I managed to delete, then having served the system well, panic I accidentally opened the Task Manager and deleted a bunch of processes that are running.

  Now, I find that, although I am connected to WiFi, I can't open Internet.  I click on Firefox, but it shows that I am unable to connect to the Internet.

  I have Windows 8; an easy way I can solve this problem?

  Thank you.

  Original title: I accidentally turned off the program that allows my computer to connect to the Internet

  Hi Tunasushiroll,

  Thanks for posting your query in Microsoft Community.

  I imagine the inconvenience that you are experiencing and will certainly help you in the right direction to solve the problem.

  The problem can occur for various reasons, including incorrect TCP/IP settings configured, firewalls third of anti-virus programs blocking the connection, or due to bad the advanced sharing settings. So, I would suggest trying the following methods and check if you system is able to detect the wireless network.

  Method 1:

  Run the troubleshooter network first, and then test your Internet connection.

  Open the Network Troubleshooter by hitting on any fly in the Dashboard screen, quilting Search(or if you use a mouse, pointing to the top right of the screen, move the mouse down and then clicking search), entering the network troubleshooterin the search box, type, or by clicking settingsand then by typing or clicking on identify and fix network problems.

  If the problem persists, try the following method.

  Method 2:

  Second of all, please check if the WLAN service is started and set to automatic. If it is stopped, then I suggest you to start the service and set it to automatic.

  1. Press the Windows key + R, type services.msc in the Run dialog box and press ENTER.
  2. Select the Autoconfiguration WLAN service in the list and double-click it.
  3. Change the startup to Automatic type, then click Start to start the service.
  4. Click apply and then click OK.
  5. Restart the computer and verify if the network is detected. If this is not the case, go to method 3.

  Method 3:

  Reset the DNS and TCP/IP settings.

  1. Press the Windows key + X, click prompt (Admin).
  2. Please enter the following commands and press ENTER after each one.

     netsh int ip reset resetlog.txt
     netsh winsock reset
     ipconfig/registerdns
     ipconfig/flushdns
     ipconfig/release

  3. Restart the computer to check the issue.

  Check if the system is able to detect the network. If this is not the case, go to method 4.

  Method 4:
  Temporarily disable the security software (if any), and check if it helps.

  Note: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you do not disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network during the time that your antivirus software is disabled, your computer is vulnerable to attacks.

  Additional information:

  Windows wireless and wired network connection problems

  Hope this information is useful. Let us know if you need more help, we will be happy to help you.

• Unable to connect to the App Store and auto delete app

  Hi, I never update my ipad because I never, and I do not have the space for it anyway. Now and then I get the message saying ipad needs space for the update, press ok to allow deletion, or something in that sense. Theres two options cancel or ok. Today I accidentally pressed ok. He deleted my largest app and now I am having problems with the App Store. I can open it and see the recommended page. I think I can upload them as well, but when I use the search bar, it says unable to connect to the App Store. I don't know what to do and how to cancel.

  First of all, make sure that you don't have enough free space before trying to re-download the application. Once you know that you have enough space, try these two ways to get to the app.

  Click on the tab purchased on the App Store and see if the application appears in a search here or just trying to slide through until you see the app and then download it from there.

  If this does not work, do a Google search for the app. It should appear in the search. Tap on the app in the Google search and who should open the description window app on the App Store with the download next to the app icon.

• Unable to connect using the current password

  Using the current password which only had 6 characters - have now changed to 8 hope if this helps solve the problem.
  Have you noticed too there was an update of Mozilla on my laptop the day before that this problem then this could be the reason?

  Unable to connect using the current password

  It is far from a complete problem description.
  Please explain in detail

  • what you were doing
  • That's happened

  Using the current password which only had 6 characters

  6 characters is a very weak password. Consider using a password manager to generate longer and more complex passwords and to remember these passwords.