Unable to load the config in to the PDM
I have recently implemented an IPsec tunnel between my PIX and a SonicWall in a remote office. Since then, I am only able to monitor the firewall of the MIP. Any suggestions? I disinfect my config to post if it would help to identify the specific rules.
Words Robert is correct,.
PDM will do this if you are using an access list in two different places
(http://www.cisco.com/univercd/cc/td/doc/product/iaabu/pix/pdm/v_30/pdmrn30.htm#94255).
I assume you have something like the following in your config file:
access-list allowed sheep ip 10.x.x.x, 192.168.x.x
NAT (inside) 0 access-list sheep
crypto 10 mymap map matches the address sheep
PDM will not allow this and find yourself in monitor mode. What you need to do (which is a better method of configuration anyway), is separated from the ACL with the following text:
access-list allowed sheep ip 10.x.x.x, 192.168.x.x
NAT (inside) 0 access-list sheep
access-list 100 permit ip 10.x.x.x, 192.168.x.x
crypto 10 mymap map matches the address 100
This separates your crypto and your ACL sheep. When you have only one IPSec peer so many people use the same ACL for both, which is fine, but as you've seen it done PDM barf. Separating the two ACL is much better, because if at some point later, you add a second, third, peer IPSec etc, you simply add a new ACL encryption for the new traffic lights and add that to your existing sheep ACL.
Hope this helps,
Jay
Tags: Cisco Security
Similar Questions
-
Error message for Virgin Gmail
"Unable to load the rich text editor.
What is the solution?
You can see https://support.mozilla.com/questions/896294
and look at this thread, the only real connection so far is it is very recent and it involves blank e-mail.Those who are in this thread say blank incoming emails doesn't work except if they Disable Adblock Plus from the icon of ADP.
In fact, the rich text editor would be in a separate file, there is most likely a connection to ADP because some of these files may be blocked. I used to have a lot of problem in this forum on the web and the tools were blocked (didn't really need them) just because I block a lot of things here: like animals to fur in nurse uniforms, a trash can (toolkit) and that blue area at the bottom of this page that interferes with scrolling and the use of the key 'end '.
Something seems to be wrong with your profile, clicking on it does not bring it upwards.
-
Satellite 1800-354 is unable to load the driver when it is turned off during the night
Hi could sombodu help me to solve this problem.
My laptop wives is unable to load the driver when its been delivered overnight. It's normal runs when the drivers installed and when it was turned off for about a half hour.
The laptop has windows xp sp2, the card is a belkin f5d7010 802.11 g and I downloaded the latest drivers for it. Thank you louis.Hello
This driver is the problem for the PCMCIA port or wireless network card?
Good bye
-
Unable to load the shared library LVASPT_WA.*
Hello
I have a hope that easy to fix the error: I want to use the function "WA Detrend' to the signal processing tool advanced in a real-time application running on a cRio 9030. When I try to run the VI I get the following error:
...
Deployment NI_AdvSigProcWA.lvlib:WA decimation Filter.vi
NI_AdvSigProcWA.lvlib:WA decimation Filter.vi loaded with errors on the target and was closed.
LabVIEW: Unable to load the shared library LVASPT_WA.*ptDecimationFilterH:C. make sure that the library is present on the target of RT. Either MAX allows you to install software from OR or FTP to transfer custom RT target libraries....
I reinstalled signals Advanced processing toolkit and linked things 'add new software' MAX, but the error persists.
A picture of what the system looks like to the MAX is attached.
Also, I Fund this post:
could someone tell me what he means by "Please check the installation of the custom software all mode '?
Can you telll me what I am doing wrong?
Thank you very much in advance!
I ran your situation in R & D, and the problem seems to be as a result of Advanced Signal Processing Toolkit is not not compatible on the x 64 under Linux RT OS in the 9030. The product page could be clearer on this gap. I am currently a web application to get this fixed!
Best,
David
-
Unable to load the shared library nilvce.*
When you try to deploy a Labview 2009 real-time application, I get the message:
Deployment XDNodeRunTimeDep.lvlib:loadnilvce.viXDNodeRunTimeDep.lvlib:loadnilvce.vi loaded with errors on the target and was closed.
LabVIEW: Unable to load the shared library nilvce. *: niLVCtrlEngineReserveProc:C on the target RT device.
Completed with errors of deploymentI reformatted the CRIO-9073 and reinstalled the software, but this did not help.
Any ideas on how to solve this problem?
I was able to solve this problem by changing the settings in a timed loop Structure.
The Source Type has been set to "synchronize in the scan engine. This change to the problem solved 1 kHz clock source.
This vi was initially written for the interface of the scan engine and reused on another project that uses the FPGA interface.
-
What should I do when I receive the message 'unable to load the flash shockwave.
What should I do when I receive the message 'unable to load the flash shockwave.
Hello
1. how many times you get this error message? This problem is limited to specific Web pages?2. Once you get this error message? What is your default browser?
Find out what version of Internet Explorer you are using
3. have you installed new hardware or software before the show?4. What is the operating system installed on the computer?
5. are you logged in as administrator?
Method 1:If you are facing problems with Internet Explorer 9, I suggest you read the article and try to run theFix it:Troubleshoot Internet Explorer to IE quick, safe and stableNote: Note that the reset Internet Explorer (IE) resets all settings defined by the user, including those established by the installed extensions, toolbars and other add-ons for IE by default. This includes all the security, privacy and settings area. Also this will erase browsing history, delete all temporary Internet, cookies, form data files and especially all the passwords.Method 2:a. search for Internet Explorer in the start menu.
b. right click and select "Run as Administrator".Check if the problem occurs.Method 3: Uninstall and reinstall Adobe ShockwaveTo uninstall a program
I also suggest you to download and install the latest version of Adobe Shockwave player and check if that helps:Provide more information about the issue so that we can better help you.I hope this helps. -
Error message "unable to load the shared library.
I try to get my programs for school to work, and I get these error message whenever I try to run anything. The last line of the State of deployment is as follows:
Deployment time get NLVSim and isAcceptedStep.vi IsAcceptedStep.vi and NILVSim get busy with errors on the target and has been closed.
LabVIEW: Unable to load the shared library NILVSim.*: SIM_GetTimeAndIsAccepted:C. make sure the library is present on the target of RT. Either MAX allows you to install software from OR or FTP to transfer custom RT target libraries.
I tried everything I can think of to fix this. I checked NEITHER Max and I'm all for date on the software. I reinstalled LabVIEW twice, and I reset my myRIO. My classmates do not experience problems with getting theres to work. I start to lose hope and hope someone might know what the question. Thank you for your help.
WubaDee,
NILVSim is part of the LV Control Design and Simulation Module. This one is correctly installed on your Windows development system and you installed it on your myRIO?
Norbert
-
I connect to my profile and I am not able to log in. The display shows "at the service of the user could not connect. User profile cannot be loaded... » » ?
Hello
These methods should help for Windows 7 or Vista.
References to Vista also apply to Windows 7.
You can try to fix it with Safe Mode - repeatedly press F8 as you bootup. The ADMIN account in trunk
Mode has no default password (unless someone has changed the password so it should be available).Some programs such as the updated Google (if you added the toolbar Google, Chrome or Google Earth)
has been known to cause this problem.Error message when you log on a Windows Vista-based or Windows 7 using computer a
Temporary profile: "the user profile Service has no logon. Unable to load the user profile.
http://support.Microsoft.com/kb/947215How to fix error "the user profile Service has no logon. User profile cannot be loaded. »
http://www.Vistax64.com/tutorials/130095-user-profile-service-failed-logon-user-profile-cannot-loaded.htmlHow to fix error "your user profile was not loaded correctly! You have been connected with a
temporary profile. "in Vista
http://www.Vistax64.com/tutorials/135858-user-profile-error-logged-temporary-profile.htmlBE VERY CAREFUL IF YOU USE THIS ONE:
DO NOT USE THE ACCOUNT HIDDEN ON A DAILY BASIS! If it corrupts you are TOAST.
-------------------------------------------------------------------------------------------------------------------------------------
For Windows 7:
http://www.SevenForums.com/tutorials/507-built-administrator-account-enable-disable.htmlUse the Admin account hidden to lower your user account APPLY / OK then wear again to
ADMIN. This allows clear of corruption. Do the same for other accounts if necessary after the
above message.You can use the hidden - administrator account to make another account as an ADMINISTRATOR with your same
password (or two with the same password) use a test or difficulty to another.You can run the command Admin account hidden from the prompt here if
necessary.How Boot for Windows 7 System Recovery Options or use a Windows 7 boot disk.
http://www.SevenForums.com/tutorials/668-system-recovery-options.htmlWhat are the system recovery options in Windows 7?
http://Windows.Microsoft.com/en-us/Windows7/what-are-the-system-recovery-options-in-Windows-7How to create a Windows 7 system repair disc
http://www.SevenForums.com/tutorials/2083-system-repair-disc-create.html-------------------------------------------------------------------------------------------------------------------------------------
For Vista:
How to enable or disable the real built-in Administrator account in Vista
http://www.Vistax64.com/tutorials/67567-administrator-account.htmlUse the Admin account hidden to lower your user account APPLY / OK then wear again to
ADMIN. This allows clear of corruption. Do the same for other accounts if necessary after the
above message.You can use the hidden - administrator account to make another account as an ADMINISTRATOR with your same
password (or two with the same password) use a test or difficulty to another.You can run the command Admin account hidden from the prompt here if
necessary.This tells you how to access the System Recovery Options and/or a Vista DVD
http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspxWhat are the system recovery options in Windows Vista?
http://Windows.Microsoft.com/en-us/Windows-Vista/what-are-the-system-recovery-options-in-Windows-VistaHow to create a Vista - free methods recovery disk
http://www.Vistax64.com/tutorials/141820-create-recovery-disc.html-------------------------------------------------------------------------------------------------------------------------------------
If you cannot access your old account, you can still use an Admin to migrate to another (don't forget
always leave to an Admin who is not used except for testing and difficulty account).Difficulty of a corrupted user profile
http://windowshelp.Microsoft.com/Windows/en-AU/help/769495bf-035C-4764-A538-c9b05c22001e1033.mspxI hope this helps.
Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="" -="" mark="" twain="" said="" it="">->
-
the user profile service has no log on, unable to load the user profile
my laptop me disconnected during use and I tried to log back on, but I get this message "user profile service does not have the log on, unable to load the user profile. But it allows me as a guest, but can't let me as an administrator. I'm 100% sure that my password is correct. How can I fix it.
Francefreedom
Hi, THIS IS a TWEAK of REGISTRY AND IS AHEAD if YOUR NOT COMFORTABLE, please do NOT ATTEMPT...
Boot into safe mode (tap F8 at startup) once your safe mode desktop computer has loaded click on the start button, type regedit hit search bar enter. Double left click HKEY_LOCAL_MACHINE next double left click scroll down to MICROSOFT SOFTWARE double left click MICROSOFT scroll down to WINDOWS NT double left click WINDOWS NT, scroll the LIST of PROFILES double click PROFILE, LIST within profile, you will see two files of script long as S-1-5-21-32778... will be a script. BAK at the end of the script. Make a right click the file that does not. BAK at the end and click Rename. Then, at the end of script .BA type highlight the. BAK file, and right click on it and click Rename. Delete the. Then, the part of the file BAK, highlight the click again right the file .BA and rename and add K to the .BA while she reads. BAK. The long without script. BAK in the end will have to be highlighted again on the right pane, you'll see REF COUNTY double-click REF COUNT and you will see a number in a box to make sure that the number is 0 (ZERO) if not change it to ZERO 0, click OK. Then and then double click on STATE and change again once the number 0 (ZERO)... Reboot and close regedit your machine and you will now be able to boot and load the administrator account once more. Hope this helps
You can also follow a tutorial step by step at this link
https://www.YouTube.com/watch?v=vEyxD6ZG-JI
Checkurtech
-
Original title: I can't connect to my admin account
Windows 7 - whenever I try to login on my admin acc it appears ("service user profile Service does not have the logon - user profile cannot be loaded") and do not know what that could have been and how to solve this problem, I have not tried anything yet if someone can please help me. I also connect to a standard ACC and cannot do anything because when he asks me my admin pass I put it in and nothing happens.Hello
This error can occur if the group policy setting "do not connect to users with temporary profiles" is configured.
Run the diagnostic tool for Fixit for the article mentioned below and if it solves the problem.
Error message when you log a computer Windows Vista-based or Windows 7 by using a temporary profile: "the user profile Service has no logon.
Unable to load the user profile.
http://support.Microsoft.com/kb/947215Let me know if you need more assistance.
Kind regards
Afzal Taher-Microsoft Support.
Visit our Microsoft answers feedback Forum and let us know what you think. -
Unable to load the user profile?
I tried command prompt, changes in safe mode, go to the control panel and changed the .bak thing, but it did not always help! It is on my ADMIN account, and all about it is blocked. I can't download or update anything because the password does not work - I can't even sync the songs on my phone because of that! So everything around having to use approval of the Admin does not work. The changes that I have on safe mode did not hit anything! What should I do?
Hello
These methods should help for Windows 7 or Vista.
References to Vista also apply to Windows 7.
You can try to fix it with Safe Mode - repeatedly press F8 as you bootup. THE ADMIN
Safe Mode account has no default password (so unless someone changed
the password should be available).Some programs such as the Google Updater (if you've added the Google toolbar,
Chrome or Google Earth) has been known to cause this problem.Error message when you log on to a Windows Vista-based or Windows 7
computer by using a temporary profile: "the user profile Service has no logon.
Unable to load the user profile.
http://support.Microsoft.com/kb/947215Difficulty "the user profile Service has no logon. User profile cannot be loaded. "Error in Windows 7
http://www.SevenForums.com/tutorials/186131-user-profile-service-failed-logon-user-profile-cannot-loaded.htmlHow to fix error "the user profile Service has no logon. Could not load user profile. "in
Vista & Windows 7.
http://www.Vistax64.com/tutorials/130095-user-profile-service-failed-logon-user-profile-cannot-loaded.htmlHow to fix error "your user profile was not loaded correctly! You have been connected with a
temporary profile. "in Vista & Windows 7.
http://www.Vistax64.com/tutorials/135858-user-profile-error-logged-temporary-profile.htmlBE VERY CAREFUL IF YOU USE THIS ONE:
DO NOT USE THE ACCOUNT HIDDEN ON A DAILY BASIS! If it corrupts you are TOAST.
----------------------------------------------------------------------------------------------------------
For Windows 7:
http://www.SevenForums.com/tutorials/507-built-administrator-account-enable-disable.htmlUse the hidden administrator account to lower your user account APPLY / OK then
Raise it to ADMIN. This allows clear of corruption. Do the same for other accounts
If necessary after following the above message.You can use the hidden - administrator account to make another account as an ADMINISTRATOR with
your password even (or two with the same password) use a test or difficulty to another.You can run the command Admin account hidden from the command prompt
from there if necessary.How Boot for Windows 7 System Recovery Options or use a Windows 7 boot disk.
http://www.SevenForums.com/tutorials/668-system-recovery-options.htmlWhat are the system recovery options in Windows 7?
http://Windows.Microsoft.com/en-us/Windows7/what-are-the-system-recovery-options-in-Windows-7How to create a Windows 7 - free methods system repair disc
http://www.SevenForums.com/tutorials/2083-system-repair-disc-create.html----------------------------------------------------------------------------------------------------------
For Vista:
How to enable or disable the real built-in Administrator account in Vista
http://www.Vistax64.com/tutorials/67567-administrator-account.htmlUse the hidden administrator account to lower your user account APPLY / OK then
Raise it to ADMIN. This allows clear of corruption. Do the same for other accounts
If necessary after following the above message.You can use the hidden - administrator account to make another account as an ADMINISTRATOR with
your password even (or two with the same password) use a test or difficulty to another.You can run the command Admin account hidden from the command prompt
from there if necessary.This tells you how to access the System Recovery Options and/or a Vista DVD
http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspxWhat are the system recovery options in Windows Vista?
http://Windows.Microsoft.com/en-us/Windows-Vista/what-are-the-system-recovery-options-in-Windows-VistaHow to create a Vista - free methods recovery disk
http://www.Vistax64.com/tutorials/141820-create-recovery-disc.html---------------------------------------------------------------------------------------------------------
If you can't access your old account you can still use an Admin to migrate to one
new (remember to always leave an account Admin who is not used except)
to test and difficulty).Difficulty of a corrupted user profile
http://windowshelp.Microsoft.com/Windows/en-AU/help/769495bf-035C-4764-A538-c9b05c22001e1033.mspxI hope this helps.
Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="">-><- mark="" twain="" said="" it="">->
-
I'm unable to load the microsoft KB 2378111 security update. I'm under Vist Home Premium. I get the error code 80070020. I tried safe mode, but no luck so far
Hello
You are supposed to try it in "Safe Mode with network"; not 'Safe Mode'.
You need a cable connection; no wireless using this method.
Start method 3, etc at this link if top is not solve:
"Error 0 x 80070020 when you use the Windows Update Web site or the Microsoft Update Web site to install the updates.
http://support.Microsoft.com/kb/883825
{Moderator note: Thread is placed in the appropriate forum}
See you soon.
-
Can re above, anyone help? Thank you
* original title - I'm having problems with "the user profile service has no logon. Unable to load the user profile"in order to resolve this that I have to sign as an administrator, but I forgot my password. What can I do? *
Only suggestion I can offer...
Go to safe mode... http://www.Vistax64.com/tutorials/123496-safe-mode.html
See if there is another account admin, you've not seen before.
If so, this is the built-in Administrator account. By default, there is no password.
Logon to the account built-in Administrator and do the following:
1 do a system restore
http://www.Vistax64.com/tutorials/76905-System-Restore-how.html2 use this tutorial from Microsoft support :
http://support.Microsoft.com/kb/947215
There are several methods, go through one by one.
Method 3 has a "fix it for me" applicationIf you don't see the built-in Administrator account... Sorry
We are not allowed to help users to bypass the password protection, regardless of what are "reasons".
Here's the Microsoft Policy about this:
http://social.answers.Microsoft.com/forums/en-us/vistasecurity/thread/3eba3150-8742-4264-be9f-0daaad2282cd -
Original title: deleted Vista ultima. admin identity and admin authorization password for standard users will not work.
I inadvertently deleted the admin. identity, I think in Vista Ultima. The photo shows still on the identities, but when I try to open the identity I get the following message, "user profile service service has no logon. User profile cannot be loaded. The admin. password does not work in any of the other identities now, so I can't do updates to most of my programs, such as windows. I can't open the control panel to add and change of identity.
Hi JBRA47,
You can consult the following Microsoft KB article and check if it helps to solve the problem:
Error message when you log a computer Windows Vista-based or Windows 7 by using a temporary profile: "the user profile Service has no logon. Unable to load the user profile.
http://support.Microsoft.com/kb/947215
Hope this information is useful.
Jeremy K
Microsoft Answers Support Engineer
Visit our Microsoft answers feedback Forum and let us know what you think.If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.
-
Error "the user profile Service has no logon. Unable to load the user profile.
Original title: admin user account
the user profile service service is a not the logon user profile cannot be loaded, this is the error I received - it's my account Admin what should I do to correct this. I have come back before this happened. Help, please
Hello
You can try to fix it with Safe Mode - repeatedly press F8 as you bootup. The ADMIN account in trunk
Mode has no default password (unless someone has changed the password so it should be available).Some programs such as the updated Google (if you added the toolbar Google, Chrome or Google Earth)
has been known to cause this problem.Error message when you log on a Windows Vista-based or Windows 7 using computer a
Temporary profile: "the user profile Service has no logon. Unable to load the user profile.
http://support.Microsoft.com/kb/947215How to fix error "the user profile Service has no logon. User profile cannot be loaded. »
http://www.Vistax64.com/tutorials/130095-user-profile-service-failed-logon-user-profile-cannot-loaded.htmlHow to fix error "your user profile was not loaded correctly! You have been connected with a
temporary profile. "in Vista
http://www.Vistax64.com/tutorials/135858-user-profile-error-logged-temporary-profile.htmlBE VERY CAREFUL IF YOU USE THIS ONE:
DO NOT USE THE ACCOUNT HIDDEN ON A DAILY BASIS! If it corrupts you are TOAST.
How to enable or disable the real built-in Administrator account in Vista
http://www.Vistax64.com/tutorials/67567-administrator-account.htmlUse the Admin account hidden to lower your user account APPLY / OK then wear again to
ADMIN. This allows clear of corruption. Do the same for other accounts if necessary after the
above message.You can use the hidden - administrator account to make another account as an ADMINISTRATOR with your same
password (or two with the same password) use a test or difficulty to another.You can run the Admin account hidden from the prompt by if necessary.
This tells you how to access the System Recovery Options and/or a Vista DVD
http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspxIf you cannot access your old account, you can still use an Admin to migrate to another (don't forget
always leave to an Admin who is not used except for testing and difficulty account).Difficulty of a corrupted user profile
http://windowshelp.Microsoft.com/Windows/en-AU/help/769495bf-035C-4764-A538-c9b05c22001e1033.mspxI hope this helps.
Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.
-
Original title: just changed password an hour ago. I can not connect.
Password just changed an hour ago. I can not connect. I don't have a password reset disk. When I type the password and press ENTER, the next page says ' THE SERVICE PROFILE has NO logon USER. USER PROFILE CANNOT BE LOADED. »
HelloThis error can occur if the group policy setting "do not connect to users with temporary profiles" is configured.
Try to connect to your computer from another user account and follow the steps listed in the article below.
Check out the following link and follow the steps to solve the problem:
Error message when you log a computer Windows Vista-based or Windows 7 by using a temporary profile: "the user profile Service has no logon. Unable to load the user profile.
http://support.Microsoft.com/kb/947215Note: If you do not have any other user account the computer checks to see if you can boot to the desktop insafe mode , and then perform the steps listed.I hope this helps.Thank you, and in what concerns:
Shekhar S - Microsoft technical support.Visit our Microsoft answers feedback Forum and let us know what you think.
If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.
Maybe you are looking for
-
Firefox blocks https://addons.mozilla.org/firefox/downloads/file/193648/super_start-3.4.4b-fx.xpi * how it to make?
-
Hello Something is happening with my Qosmio G20.Sometimes when I connect the plug to the computer the DC IN indicator flashes orange and the pc does not start.A few hours later I try again and now DC IN indicator shows blue and I can boot my pc and I
-
The Explorer does not display my SDCard on the Satellite A100-906
Hello world...I have this problem which is actually when I insert an sd card in the slot of my satellite a100-906, the computer recognizes the card (I get the safe removal in the systray) but Explorer doesn't show anything. I installed the last flash
-
My speakers on my computer laptop dv7-6b56nr do not work
I have a pavilion dv7-6b56nr laptop computer. When I originally bought the external speaker audio beats DID work correctly. Him now NOT. Can you please helpp me? I would appreciate it a lot, because it was one of the options that the computer off
-
Windows Update error