Unable to telnet to C60

Similar Questions

• Unable to telnet BB10 dev alpha Simulator

  I'm not able to telnet Simulator running after a command...

  Telnet

  It gives me error: could not open connection to the host, on port 23: Connect failed

  For this reason, I can't deploy my application on the Simulator.

  Thank you.

  In fact, the problem was different. Network card in the computer virtual has been disabled. Therefore, IDE was not able to find out. Permit to it and its working now. Dumb question

• Remote VPN client and Telnet to ASA

  Hi guys

  I have an ASA connected to the Cisco 2821 router firewall.

  I have the router ADSL and lease line connected.

  All my traffic for web ports etc. of ADSL ftp and smtp pop3, telnet etc is going to rental online.

  My questions as follows:

  I am unable to telnet to ASA outside Interface although its configuered.

  Unable to connect my remote VPN Client, there is no package debug crypto isakmp, I know that I have a nat that is my before router device my asa, I owe not nat port 4500 and esp more there, but how his confusion.

  I'm ataching configuration.

  Concerning

  It looks like a config issue. Possibly need debug output "debug crypto isa 127".

  You may need remove the command «LOCAL authority-server-group»

  NAT-traversal is enabled by default on the ASA 8.x version. So you don't have to worry about NAT device in the middle.

• Telnet to the PIX from the outside

  I tried the task through several suggestions.

  None of which worked. My last try was using this link.

  http://www.Cisco.com/en/us/customer/products/sw/secursw/ps2120/products_user_guide_chapter09186a0080089bd6.html

  PIX VPN client works fine however I am still unable to telnet to the PIX.

  In addition, the document speaks of configuration on the client.

  Step 3 in the VPN client, create a security policy that specifies the IP address of the remote party identity and IP gateway under the same IP address IP address of the external interface of the PIX firewall. In this example, the IP address of the PIX firewall outside is 168.20.1.5.

  I see there is only one place to put an IP address on the client. There is no place on the client to a gateway address. I tried to change my gateway machine and it still does not work.

  Does anyone have a config to work on how to Telnet to a PIX from the outside?

  The step that you are referencing is for users who use the old client VPN CiscoSecure. Do you really use that? I'm guessing that you are actually using the VPN client 3000, in which case you just have:

  (1) an acl of encryption that allows the traffic of your address has been assigned outside the pix

  (2) a statement of telnet that allows telnet address assigned from outside

  i.e.

  no_nat of ip host 200.1.1.1 access list permit 10.1.1.100

  Telnet 10.1.1.100 255.255.255.255 outside

  HTH

  Jeff

• VPN site to Site from one-way data (need help)

  Hello

  Scenario:

  VPN site to Site with Cisco 837 routers:

  Place: Clients and printers

  Site B: server queues and Print

  Site A can communicate via VPN using RDP to site B, very well.

  Question:

  Site B cannot send print jobs to printers on the Site A. also unable to telnet and other access devices on the Site A of the Site (B) Pings work correctly but to all devices.

  Debugging on site an access-list 110 showed no response traffic to the Site B via the VPN?

  I tried change ip tcp adjust 1452 but not good...

  Attached configs.

  An IOS - c837-k9o3y6 - mz.123 - 4.T3.bin site

  SITE B IOS - c837-k9o3sy6 - mz.123 - 2.XC2.bin

  Any help would be appreciated.

  Thank you very much...

  Thank you for including the configs and IOS versions. Looks like you hit a bug known to FW IOS (http://www.cisco.com/cgi-bin/Support/Bugtool/onebug.pl?bugid=CSCec78231&Submit=Search), you can perform debugging as described in details to see for sure. It is difficult to understand what router would be the culprit in a scenario when both run on a tunnel L2L CBAC, but probably RouterA is dropping packets. This would also explain why pings work but TCP connections are not.

  I would upgrade TWO routers to be the same version anyway, you encounter far fewer problems in this way, but make sure that you upgrade to one fixed-In version (or later version), has to work around the problem.

• Check sensor SFR with FireSight via VPN - does not work

  Hello security experts.

  I have an ASA5515-X with SFR installed 5.4.0 and manage with 5.4 FireSight installed on the virtual machine on LAN and I record the sensor without any problem but when I try to register the sensor to FireSight via VPN I can't do. The interface on the ASA management has no intellectual property nor nameif configured and the interface is connected to the switch, SFR has the IP even configured as LAN addressing. I can see traffic being exchanged between the sensor and the FireSight but I can't save the sensor.

  Has anyone managed to register the sensor via VPN? Is there something else to be configured in order to save the sensor with the MC via the VPN?

  The delay between the Firesight and the sensor (on WAN and VPN) I get between 80 and 100 ms, what could be the problem?

  Thank you very much!

  Remi

  Hello

  If you are unable to telnet from DC to the sensor on the port 8305 delivers connectivity then.

  Can try you to ping from sensor to DC:

  ping -M do -c 20 -s 1572 

  By default, the MTU is 1500 on eth0, if the ping does not work I will suggest to lower the MTU on the interface and see if it works. See also: / var/log/messages | grep sftunnel and see the error messages on DC and sensor and send it to me everywhere. Best regards, Aastha Bhardwaj rate if this is useful!

• IP has changed. PDM inaccessible.

  I have a PIX 615 6.3 running. I changed my IP addressing scheme and so changed my address on my PIX. I am now able to ping to the new private address, but I am unable to telnet or https access. I even tried a stealth port scan and all ports were closed.

  Is there a way to recover?

  Hello.. because you you changed the intellectual property system... you must also change your ssh and http access before you can connect to the PIX inside interface.

  SSH inside

  HTTP inside

  I hope this helps... Please, write it down so it doesn't!

• Unable to SSH/telnet through the remote access VPN to ASA interface

  Hi all - im trying to SSH/telnet to my ASA in my remote access VPN tunnel but

  can't get this to work.  what Miss me?

  remote access VPN subnet: 192.168.25.0

  LAN subnet: 192.168.1.0

  config is attached.  THX-

  Please enter the command

  Private access Managament

  and you will be able to telnet/ssh to the asa on this ip 192.168.1.253

• Unable to connect to the virtual machine via telnet

  Hi all

  The VM on Vcenter everything is perfect with the network connection. I can't do a ping of the virtual machine remotely but I can not connect via telnet.

  For the same reason? And even more, I have disabled the fiewalls of the virtual machine (Windows 2008 R2).

  The error that says: could not open connection to the host, on port 23: Connect failed

  Can you please let me know how to solve this problem?

  Since there is nothing blocking the traffic of the virtual machine in ESXi, you can begin troubleshooting in the guest OS. For example is running telnet server and configured to accept connections?

  André

• OUT OF THE BOX QUESTION C60

  Anyone know if the same firmware is installed in sw1 and sw2 on a C60 out of the box?

  SECOND QUESTION: what happens if none is the process to factory reset a C Series codec if for some reason, unable to use the serial port?

  Thank you.

  Hello

  Only one of the memory banks must be populated with a version of the software out of the box.

  The second question depends on which codec C series you mean. C20 can be hard reset (power button sequence) while C40, C60 and C90 cannot and must be done either through web series, touch, telnet or ssh where each of them except series requires a network connection.

  / Magnus

• Unable to connect to the software update server (127.0.0.1)

  I'm under El Capitan 10.14.4

  I'm unable to view or download from the App store apple updates. Everything else in the app store works fine except the updates and the updates, I get 3rd party updates, but nothing from apple. If I click on updates at the top of the app store icon I get the following error

  

  Troubleshooting steps I went through far

  • I restarted my mac a few times
  • I did some research on Google and messages more speak of iworm, fortunately I could find no trace of an infection by the worm, I scanned my machine using Sphos and ClamXav and haven't found anything relating to iWorm. I am also unable to find all the files, he leaves behind him, so I think I'm safe in this regard.
  • I checked the hosts file and there are no entries that should not be there, hosts file is copied below.

  # Database host

  #

  localhost # is used to configure the loopback interface

  # When the system boots.  Do not change this entry.

  ##

  127.0.0.1 localhost

  255.255.255.255 broadcasthost

  : 1 localhost

  • The /var/log/install.log which appear relevant lines are;

  May 26 09:44:02 macbook-pro softwareupdated [435]: SUScan: Scan for pid 435 client (/ System/Library/CoreServices/Software Update.app/Contents/Resources/softwareupdated)

  May 26 09:44:02 macbook-pro softwareupdated [435]: SUScan: out of time scan = 0.2

  May 26 09:44:02 macbook-pro softwareupdated [435]: SUScan: error in scan: error Domain = NSURLErrorDomain Code =-1004 'unable to connect to the software update server (127.0.0.1)." UserInfo = {NSErrorFailingURLKey =http://127.0.0.1/content/catalogs/others/index-10.11-10.10-10.9-mountainlion-lio n-snowleopard - leopard.merged - 1_disabled.sucatalog, SUCatalogFetchOverrideURLString =http://127.0.0.1/content/catalogs/others/index-10.11-10.10-10.9-mountainlion-lio n-snowleopard - leopard.merged - 1_disabled.sucatalog, NSLocalizedRecoverySuggestion = check that your network connection is working normally.} {If there is no problems with your connection, contact your network administrator for assistance., NSLocalizedDescription = can connect to the software update server (127.0.0.1)., SUErrorRelatedCode = SUErrorCodeScanCatalogNotFound, SUErrorUpdateServerName = 127.0.0.1, NSErrorFailingURLStringKey =http://127.0.0.1/content/catalogs/others/index-10.11-10.10-10.9-mountainlion-lio n-snowleopard - leopard.merged - 1_disabled.sucatalog, _kCFStreamErrorDomainKey = 1, _kCFStreamErrorCodeKey = 61}

  May 26 09:44:02 macbook-pro softwareupdated [435]: Scan received the error unable to connect to the software update server (127.0.0.1).

  May 26 09:44:02 macbook-pro softwareupdated [435]: updates marked ramps

  • I can ping swscan.apple.com and she is resolved to 17.164.1.22 which is the same IP that also resolves the mac next to me (which gets the update)
  • I cannot telnet on port 443 to swscan.apple.com and it connects.
  • I have a mac in yosemite next to me who can see the updates so I suspect that doesn't pose any problems with the service itself rather something on why machine.
  • I started in safe mode, and while in safe mode, I get the same error.

  I am at a complete loss what to do next short of wiping and restore from a time machine backup, can anyone help please

  You can try to disable the Sophos websheild and ClamXav if she has one. Even better would be to uninstall both and test.

  FWIW, it is never a good idea to have 2 av programs installed.

• ReadyNas NV + Inaccessible Frontview. How to fix with Telnet?

  I have a Readynas NV + which allows more access to Frontview. It is more than likely linked to the size of the file log and my OS partition. I recently did a factory reset and forgot to activate the SSH module. Now I'm unable to access the root directory. I was wondering if there are options for this? I tried to do it through Telnet, but without success. I have about 4 TB of data and do not want to save it to the top (it would take days) and I was wondering if anyone has any ideas.

  -Thank you

  Thanks for your help. It's that log files were too important. I had a readynasremote.log file which was very large. Delete this file, frontview was able to load.

  Thanks again,

  Stand

• Unable to send email. time to connect to the server. Worked yesterday. Work on other computers just stopped on this one. Windows 10

  All of a sudden I can no longer send emails from Thunderbird. Works on other computers running windows 10 but not this one. I can still receive emails. Tried to disable windows defender and windows firewall. Uninstalled and reinstalled Thunderbird. Accounts deleted and then added back in. Is still unable to send emails.

  Your domain name for mail servers is ok, mail.batterybattery.ca is located in the MX record for your domain. Server IP is 209.15.208.71.

  I just tried to telnet your provider, but it does not respond on 587 (as it has been filtered). Tried other ports and they seem good.

  Try to use SSL and port 465 instead of 587 and tls.

• CSR1000v - Extra return in telnet line/transport

  I'm running a weird question with a few CSR1000v routers circula 5.1 ESXi.  I created 10 virtual machines and of these 10 cases, I have 1 router which seems if insert an extra line (or a carriage return) in the CLI whenever I hit him "enter."  This question followed between SecureCRT and PuTTY.  I am also unable to use the "tab" key, upward or down arrows for the history and the '?' does not exit until I hit "enter".  Some examples follow:

  Router >
  Router > en
  en
  Router #.
  Router #.

  Arrow:

  Router #^ [[has

  Arrow:

  Router #^ [[B

  Tab key:

  Router > ^ I

  I am using the 'serial console platform' configuration and telnet to my ESXi server with port number address, IE: 172.100.100.2:2003 for Router3.  If I telnet between my routers (R1 telnets to an IP address on the interface of the CSR), the issue does not follow.  However, now that I have create my VM 11th and 12th, I see the extra line in the sessions during the series of console output.

  Anyone ever encountered this before?

  Good news!  Mark as resolved for others to find.  Kevin

• Configure SSH/Telnet on a WPA2000

  Hello

  I'm trying to configure SSH/Telnet on a Wireless-G WPA2000 Access Point. I have looked for documentation but am unable to find those who said how to do that via the interface user, and I don't see any obvious place where this could be. Someone managed based on setting this up? I would prefer SSH but telnet will do.

  Hi Sarah, small business wireless products do not support a CLI configuration, so no document. In addition, the only management options would be via http/https and SNMP V1, 2, 3.

  -Tom
  Please mark replied messages useful